Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Aplicação da metodologia de planejamento de experimentos para formulação de massas cerâmicas para telhas

Rio Grande do Norte State stands out as one great producer of structural clay of the brazilian northeastern. The Valley Assu ceramic tiles production stands out obtained from ilitics ball clays that abound in the region under study. Ceramics formulation and the design of experiments with mixture approach, has been applied for researchers, come as an important aid to decrease the number of experiments necessary to the optimization. In this context, the objective of this work is to evaluate the effects of the formulation, temperature and heating rate in the physical-mechanical properties of the red ceramic body used for roofing tile fabrication of the Valley Assu, using design of mixture experiments. Four clays samples used in two ceramics industry of the region were use as raw material and characterized by X-ray diffraction, chemical composition, differential thermal analysis (DTA), thermogravimetric analysis (TGA), particle size distribution analysis and plasticity techniques. Afterwards, they were defined initial molded bodies and made specimens were then prepared by uniaxial pressing at 25 MPa before firing at 850, 950 and 1050 ºC in a laboratory furnace, with heating rate in the proportions of 5, 10 e 15 ºC/min. The following tecnologicals properties were evaluated: linear firing shrinkage, water absorption and flexural strength. Results show that the temperature 1050 ºC and heating rate of 5 ºC/min was the best condition, therefore presented significance in all physical-mechanical properties. The model was accepted as valid based of the production of three new formulations with fractions mass diferents of the initial molded bodies and heated with temperature at 1050 ºC and heating rate of 5 ºC/min. Considering the formulation, temperature and heating rate as variables of the equations, another model was suggested, where from the aplication of design of experiments with mixtures was possible to get a best formulation, whose experimental error is the minor in relation to the too much formulations

Investigação das alterações citogenéticas em pacientes pediátricos com leucemia linfóide aguda do Rio Grande do Norte

Leukemia is a heterogeneous group of hematologic malignancies that result from partial or total transformation of the blast cells. The Acute Lymphoblastic Leukemia (ALL) is the most common malignancy in childhood, especially in male, Caucasian children younger than 14 years. Several criteria are adopted to classify ALL, including the cell morphology, cytochemistry, immunophenotyping and cytogenetic analysis. Cytogenetic studies allow a more detailed analysis to detect chromosomal abnormalities of leukemic cells. These modifications will determine the diagnosis, classification, stage characterization, remission assessment and prognosis. In this study were evaluated 30 patients, aged from four months to seventeen years, of both sexes and various ethnicities. The age distribution showed that 67% of patients had between one and ten years (with mean age of XX years old), the most prevalent ethnic was Caucasian (50%) and 57% were males. According to immunophenotype, 93% of patients had B-cells progenitor ALL and 7% early lineage T. Considering the total studied population, the most frequent medical findings were lymphadenopathy (37%), hepatomegaly (77%) and splenomegaly (70%), where one patient could present more than one of these medical findings. Regarding the CBC, the majority of patients had hemoglobin below 10 g / dl (73%), leukocyte count less than 10.000/μL (60%) and platelet count below 150.000/μL (83%). Chromosomal abnormalities were observed in 64% of all patients, where hyperdiploidy was the most common numerical change (67%), followed by hypodiploid (33%). All these data are in agreement with the literature. Moreover, complexes structural and/or number changes not yet described in literature were observed, which indicated poor prognosis. Finally, we concluded that this study demonstrated the importance of cytogenetic study in the diagnosis and identification of prognostic factors in pediatric patients with ALL in Rio Grande do Norte. The results obtained in this study are extremely useful and emphasizes that surveys of this nature must be conducted more frequently in our state

Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace

Análise das propriedades termofísicas, mecânicas e geométricas de telhas cerâmicas queimadas em forno caieira e forno abóbada

In the industry of ceramic in Rio G. do Norte, tile stands out as the most manufactured product by this industry, being the intermittent kiln abóbada and caieira the principal type of kiln used in burning. There was a need to make a study of the influence exerted by the type of kiln in which tiles are burnt in their thermo physical properties. The analysis started with 24 raw samples of tile, which was split in two groups of 12 samples and burnt in Abóbada and Caieira kiln. Besides that, it was made study of the tax of heat transfer to the environment (for each kiln). After having been burnt the samples were taken for laboratory analysis. The properties verified were impermeability, determination of dry mass, absorption of water, the load of bending rupture and its geometric characteristics, the tests were conducted following the currents standards. The tests were carried out according to the ABNT - NBR 15310. The calculation of the rate of heat transfer showed that the abóbada kiln is more efficient than the Caieira, however the results of tests on the samples revealed no superiority of one over another sample. So the furnace had no influence on the performance of the ceramic tiles

Viabilidade térmica de um forno solar fabricado com sucatas de pneus

The proposed design provides a solar furnace alternative, box-like, low-cost operation to be used in cooking, comprising three scrap tires to make the recycling thereof. The tires were coupled to each other, forming an enclosure, which stood on its bottom covered by a parable multiple mirrors made from a urupema (sieve indigenous) and the inner sides of the oven aluminum sheet painted black, obtained from beer cans, thus being made to obtain the increase in the concentration of solar radiation incident on the inside of the prototype studied. Two tires were attached, leaving an air layer between them, with the function of thermal insulation. The third tire aimed to support the other two and thermally insulate the bottom of the oven. Externally was placed a metal frame with flat mirrors to reflect the incident rays into the oven, having a mobility to correct the apparent motion of the sun. Its primary feature is the viability of clean, renewable energy to society by tackling the ecological damage caused by the large-scale use of wood for cooking food. The tests show that the furnace reached the maximum temperature of 123.8 °C and baking various foods such as pizza, bun, and other lasagne in an average time 50 minutes. Proves the feasibility of using the oven. Presenting still able to improve their performance with the addition of new materials, equipment and techniques

Tratamento de materiais contaminados com bifenilas policloradas (PCBS) via extração convencional e fluído supercrítico

The decontamination of the materials has been subject of some studies. One of the factors that it increases the pollution is the lack of responsibility in the discarding of toxic trash, as for example the presence of PCB (Polychlorinated Biphenyls) in the environment. In the Brazilian regulations, the material contaminated with PCB in concentrations higher than 50 ppm must be stored in special places or destroyed, usually by incineration in plasma furnace with dual steps. Due to high cost of the procedure, new methodologies of PCBs removal has been studied. The objective of this study was to develop an experimental methodology and analytical methodology for quantification of removal of PCBs through out the processes of extractions using supercritical fluid and Soxhlet method, also technical efficiency of the two processes of extraction, in the treatment of contaminated materials with PCBs. The materials studied were soils and wood, both were simulated contamination with concentration of 6.000, 33.000 and 60.000 mg of PCB/ kg of materials. Soxhlet extractions were performed using 100 ml of hexane, and temperature of 180 ºC. Extractions by fluid supercritical were performed at conditions of 200 bar, 70°C, and supercritical CO2 flow-rate of 3 g/min for 1-3 hours. The extracts obtained were quantified using Gas chromatography-mass spectrometry (GC/MS). The conventional extractions were made according to factorial experimental planning technique 22, with aim of study the influence of two variables of process extraction for the Soxhlet method: contaminant concentration and extraction time for obtain a maximum removal of PCB in the materials. The extractions for Soxhlet method were efficient for extraction of PCBs in soil and wood in both solvent studied (hexane and ethanol). In the experimental extraction in soils, the better efficient of removal of PCBs using ethanol as solvent was 81.3% than 95% for the extraction using hexane as solvent, for equal time of extraction. The results of the extraction with wood showed statistically it that there is not difference between the extractions in both solvent studied. The supercritical fluid extraction in the conditions studied showed better efficiency in the extraction of PCBs in the wood matrix than in soil, for two hours extractions the obtain percentual of 43.9 ± 0.5 % for the total of PCBs extracted in the soils against 95.1 ± 0,5% for the total of PCBs extracted in the wood. The results demonstrated that the extractions were satisfactory for both technical studied

Evolução do reparo por excisão de nucleotídeo

The phylogeny is one of the main activities of the modern taxonomists and a way to reconstruct the history of the life through comparative analysis of these sequences stored in their genomes aimed find any justification for the origin or evolution of them. Among the sequences with a high level of conservation are the genes of repair because it is important for the conservation and maintenance of genetic stability. Hence, variations in repair genes, as the genes of the nucleotide excision repair (NER), may indicate a possible gene transfer between species. This study aimed to examine the evolutionary history of the components of the NER. For this, sequences of UVRA, UVRB, UVRC and XPB were obtained from GenBank by Blast-p, considering 10-15 as cutoff to create a database. Phylogenetic studies were done using algorithms in PAUP programs, BAYES and PHYLIP package. Phylogenetic trees were build with protein sequences and with sequences of 16S ribosomal RNA for comparative analysis by the methods of parsimony, likelihood and Bayesian. The XPB tree shows that archaeal´s XPB helicases are similar to eukaryotic helicases. According to this data, we infer that the eukaryote nucleotide excision repair system had appeared in Archaea. At UVRA, UVRB and UVRC trees was found a monophyletic group formed by three species of epsilonproteobacterias class, three species of mollicutes class and archaeabacterias of Methanobacteria and Methanococci classes. This information is supported by a tree obtained with the proteins, UVRA, UVRB and UVRC concatenated. Thus, although there are arguments in the literature defending the horizontal transfer of the system uvrABC of bacteria to archaeabacterias, the analysis made in this study suggests that occurred a vertical transfer, from archaeabacteria, of both the NER genes: uvrABC and XPs. According the parsimony, this is the best way because of the occurrence of monophyletic groups, the time of divergence of classes and number of archaeabacterias species with uvrABC system

Análise comparativa dos genes de reparo do DNA em Gluconacetobacter diazotrophicus e Gluconobacter oxydans

Gluconacetobacter diazotrophicus é uma alfa-proteobactéria Gram-negativa, tolerante a meios ácidos, fixadora de nitrogênio atmosférico e foi a primeira bactéria diazotrófica endofítica isolada da cana-de-açúcar. Por sua vez, Gluconobacter oxydans, também alfa-proteobactéria Gram-negativa, possui a capacidade de oxidar incompletamente alcoóis e carboidratos. Ambas de interesse biotecnológico e industrial, essas bactérias tiveram seus genomas seqüenciados completamente em 2007. Desta forma, foi de interesse desse trabalho analisar e comparar os genes de reparo do DNA devido sua importância na manutenção da integridade genômica. Sendo assim, as vias de reparo presentes nos dois organismos foram identificadas, utilizando como base uma terceira alfa-proteobactéria, a Caulobacter crescentus, cujos genes de reparo foram descritos por um trabalho anterior e também os genes bem estabelecidos para o reparo do DNA em Escherichia coli. Para esse estudo, um banco de dados contendo ortólogos para os genes de reparo de DNA encontrados nos organismos foi criado e análises comparativas por similaridade usando o pacote Blast e o software Clustal foram feitas. Este estudo demonstrou que as principais vias de reparo ao DNA reparos por excisão, reparo direto, reparo recombinacional e reparo pelo sistema SOS estão presentes nos organismos analisados, demonstrando, na maioria das vezes, boa similaridade com E. coli. Interessantemente, foram encontradas duplicações gênicas nos quais uma das cópias estava presente no cromossomo e a outra, no plasmídeo, como no caso de UvrD, DnaE e Ssb, possivelmente caracterizando eventos de transferência lateral. Por fim, uma grande novidade foi a identificação de ortólogos para RecB em G. diazotrophicus e G. oxydans e de ortólogos duplicados de RecD em G. diazotrophicus. Até o momento, não havia sido relatada a presença de membros da via de iniciação RecBCD do reparo recombinacional em alfaproteobactérias