Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel

Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel

Estudo da incorporação de resíduos de perfuração para aplicação em cimentação de poços de petróleo

During the drilling of oil and natural gas are generated solid waste, liquid and gaseous. These solid fragments, which are known as cuttings, are carried to the surface through the drilling fluid. Furthermore, this fluid serves to cool the bit, keeping the internal pressure of the well, and others. This solid residue is very polluting, because it has incorporated beyond the drilling fluid, which has several chemical additives harmful to the environment, some heavy metals that are harmful to the environment, such as lead. To minimize the residue generated, are currently being studied numerous techniques to mitigate the problems that such waste can cause to the environment, like addition of cuttings in the composition of soil cement brick masonry construction, addition of cuttings on the clay matrix for the manufacture of solid masonry bricks and ceramic blocks and coprocessing of the cuttings in cement. So, the main objective of this work is the incorporation of cuttings drilling of oil wells, the cement slurry used in the cementing operation of the well. This cuttings used in this study, arising from the formation Pendências, was milled and separated in a sieve of 100 mesh. After grinding had a mean particle sike in order of 86 mm and crystal structure containing phases of quartz and calcite type, characteristic of the Portland cement. Were formulated and prepared slurries of cement with density 13 lb / gal, containing different concentrations of gravel, and realized characterization tests API SPEC 10A and RP 10B. Free water tests showed values lower than 5.9% and the rheological model that best described the behavior of the mixtures was the power. The results of compressive strength (10.3 MPa) and stability (Dr <0.5 lb / gal) had values within the set of operational procedures. Thus, the gravel from the drilling operation, may be used as binders in addition to Portland cement oil wells, in order to reuse this waste and reduce the cost of the cement paste.

Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery

Avaliação da incorporação de cinzas de lodo de esgoto como adição mineral em concretos de cimento Portland

O desenvolvimento das grandes cidades tem gerado um dos maiores desafios ambientais enfrentados na atualidade, que é a gestão eficaz de resíduos sólidos. A grande variedade e quantidade dos resíduos produzidos diariamente, tem tornado a destinação ecologicamente correta e sustentável destes materiais cada vez mais difícil. Dentre os vários resíduos produzidos diariamente destacam-se os lodos oriundos de estações de tratamento de esgotos, denominados de lodos de esgoto, cuja destinação final segura tem sido discutida mundialmente em diversos estudos, tendo em vista que a tendência de geração deste tipo de resíduo tende a crescer com o aumento do saneamento das cidades. Uma forma amplamente difundida nos países desenvolvidos para destinação dos lodos de esgoto é a incineração destes materiais para posterior envio das cinzas geradas neste processo a aterros sanitários. Porém, tem-se estudado formas alternativas de disposição, destacando-se a utilização destas cinzas como adição mineral em concretos e argamassas de cimento Portland. Sabe-se que o desempenho de resíduos de incineração como adição mineral em matrizes cimentícias, depende em grande parte da capacidade de atuação destes materiais como elementos pozolânicos ou como fileres, podendo estas características serem influenciadas pela temperatura de queima ao qual estes resíduos foram submetidos. Neste sentido, verificou-se com esta pesquisa a influência da temperatura empregada na queima dos lodos sépticos no índice de atividade pozolânica (IAP) das cinzas geradas como resíduo deste processo, aqui denominadas de cinzas de lodo séptico (CLS), sendo em seguida, avaliadas as implicações técnicas e microestruturais da utilização deste resíduo em teores de 10%, 20% e 30% como adição mineral em concretos de cimento Portland. Os resultados obtidos demonstraram não haver alterações significativas no IAP das CLS em decorrência da temperatura utilizada durante o processo de queima dos lodos de esgoto. Além disso, verificou-se que embora a utilização das CLS tenham provocado diminuição da trabalhabilidade dos concretos para todos os teores de incorporação, estas melhoraram a resistência mecânica à compressão, o índice de vazios, a absorção de água e o comportamento microestrutural dos concretos contendo 10% e 20% de resíduo

Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery

Comércio internacional e meio ambiente: estímulo à produção sustentável ou mero protecionismo comercial a posição do Brasil em dois casos de litígio

The World Trade Organization (WTO) was established in 1994 as a result of the Uruguay Round, and has as its principal aim advocate for the maintenance of free trade between nations. The preamble of its Constitutive Agreement specifically cites as an institution the goal of achieving sustainable development and the pursuit of protecting and preserving the environment, bringing into the sphere of world trade the idea that concern for the environmental cause is not restricted only the group of environmentalists, but rather has entered the economic landscape in a way not only ideological, but also pragmatic. The General Agreement on Tariffs and Trade (GATT) 1947, part of the GATT 1994, contains a device that allows the adoption of trade restrictive measures, provided that such measures aimed at protecting the environment - Article XX. The Settlement Body (DSB) is part of the WTO and acts in dissolving disputes between the countries motivated by trade. It examines two cases where countries have imposed restrictive trade measures with environmental justification. The first case was closed in 1996, with award of damages given to Brazil, on the breakdown of U.S. environmental legislation imposed on imported gasoline from Brazil - and the second, begun in 2005 and closed in 2007, coming out victorious again Brazil is on the import ban on retreaded tires to Brazil. The objective is to answer the question: how the environment is treated in the midst of trade discussions - which is aimed at its protection or its use with economic objectives in disguise? For the preparation of this work, extensive documentary research was undertaken with the virtual site of the WTO to review the entire production of legal cases and subsequent analysis of the key issue for the work, and literature of authors who have studied the tense relationship between trade international environment. The first case, it could be seen that the political movement performed by the U.S. with the aim of achieving acceptable standards of air quality was an institutional effort to ensure the quality of air, and thus would be inappropriate to say that the regulation of gasoline was merely a disguised trade barrier.However, a careful analysis of the implementation and operation of gasoline regulation may reveal intentions disguised trade and U.S. environmental argument did not hold. The weight of this environment was relegated, since there were clearly outside interests to the environmental cause. The second case, it was realized that, despite clear attempts by the EC to promote ecological dumping, send when brought to Brazil, supposedly a country with weaker environmental structure on surveillance, a residue that, pursuant to internal policies, as could not be sent to their own landfills, the Brazilian discourse remained focused on the environmental cause, and this sort there was the existence of disguised trade barriers, but of importance, at least a priori, the discussion of foreign forces on the environment environment because there is no way to legally justify the reversal of the total understanding of the first judging body, the sight of all the arguments presented by Brazil and the nonsubmission of new facts upon appeal. Still, quite heartening to reflect on the role of trade liberalization on the environment in general, because, while they do not reach a definitive conclusion will reveal positions in both directions, both for and against, the that only adds to the discussions and makes this a very fertile topic for future research

Secagem de resíduo de goiaba em secador convectivo de bandejas: modelagem matemática e análise do processo

Actually, Brazil is one of the larger fruit producer worldwide, with most of its production being consumed in nature way or either as juice or pulp. It is important to highlig ht in the fruit productive chain there are a lot lose due mainly to climate reasons, as well as storage, transportation, season, market, etc. It is known that in the pulp and fruit processing industy a yield of 50% (in mass) is usually obtained, with the other part discarded as waste. However, since most this waste has a high nutrient content it can be used to generate added - value products. In this case, drying plays an important role as an alternative process in order to improve these wastes generated by the fruit industry. However, despite the advantage of using this technique in order to improve such wastes, issues as a higher power demand as well as the thermal efficiency limitation should be addressed. Therefore, the control of the main variables in t his drying process is quite important in order to obtain operational conditions to produce a final product with the target specification as well as with a lower power cost. M athematical models can be applied to this process as a tool in order to optimize t he best conditions. The main aim of this work was to evaluate the drying behaviour of a guava industrial pulp waste using a batch system with a convective - tray dryer both experimentally and using mathematical modeling. In the experimental study , the dryin g carried out using a group of trays as well as the power consume were assayed as response to the effects of operational conditions (temperature, drying air flow rate and solid mass). Obtained results allowed observing the most significant variables in the process. On the other hand, the phenomenological mathematical model was validated and allowed to follow the moisture profile as well as the temperature in the solid and gas phases in every tray. Simulation results showed the most favorable procedure to o btain the minimum processing time as well as the lower power demand.

A estrutura burocrática de poder no stricto sensu em administração no Brasil: o caso do mestrado profissional em administração pública em Rede Nacional - PROFIAP

This study approaches bureaucratic organizational structures with the aim to understand the adherence procedure to virtual technologies in the stricto sensu educational administrative process. Thus, the author navigates through the formation of these organizations in Brazil with the intent to demonstrate the bureaucratic organizational culture and the consequent form of domination of those who detain power. In this epistemological construction, the author explores the culture s bureaucratic environment and the organizational power. In the analyses, it was observed the technological phenomenon in the ODL s administrative environment, which can explain the adherence procedure to structures and technological instruments for stricto sensu courses that, hypothetically, dilutes the traditional inherited organizational axiom. Therefore, it was utilized as object of study the Professional Master s degree in National Scale Public Administration PROFIAP, hence analyzing the documental content and the legislation related to institutionalization as well as the positioning of professors/coordinators and of the director of CAPES/MEC. Considering this axioms, it was concluded that the bureaucratic structures can admit ODL in the stricto sensu s environment. However, this can only be done as long as the adherence does not imply in a dilution of the traditional forms of power and institutional bureaucratic inherited dominance, as well as the alleged hegemony of the governmental structure in the educational administration adopted in person by the stricto sensu courses in Brazil

Combater as secas e defender as florestas a natureza nos desafios da ciência e da técnica para modernizar o Brasil (1889 a 1934)

In the first decades of 20th century the just instituted Brazilian Republic faced the challenge to modernize the country. Considering that the progress was associated with the exhaustion of the forest reserves and with climatic changes, two big issues were seen as fundamental: To Fight the Droughts and To Defend the Forests; headed by professionals who were dedicated to these ideals. This research starts from the premise that these were the main challenges enforced by nature to the Brazilian development; the general objective was delimited in the search to understand the meaning and the conception of the natural world by this group of professionals who faced the shock between modernizing the country and conserving its natural resources. Aiming to contribute with the construction of the Brazilian environmental history and to bring historical elements to the debate about the environment in the country, the author concentrates his attention to the analyses, the discussions and the actions that preceded the regulation on the use of natural resources and the implementation of the environmental legislation in Brazil, occurred in 1934. The investigation uses as methodological basis the theoretical directions of environmental history, using sources of data still little explored and valued. In such way, it is taken as starting point some published papers about this subject during the period between 1889 and 1934 in two technical magazines the Revista Brazil Ferro-Carril and the Revista do Club de Engenharia. National engineering played a basic role in this process while arguing, projecting and constructing the development. The formulated proposals, after being divulged, had fomented the interchange with other professionals and had favored the advance of ambient questions in Brazil, in the sense to preserve natural resources, to construct more harmonic relations between the society and the nature and to equate the development with the environment preservation

Estrutura e dinâmica do fitoplânctone bacterioplâncton em cultivos de camarão no Rio Grande do Norte-Brasil: impacto sobre o ambiente natural

This work aimed to study the structure and dynamic of Phytoplankton and Bacterioplankton in a complete cycle of shrimp cultivation (Litopenaeus vannamei) and determine the environmental factors responsible for the structural changes of these communities. The study was realized in a saltwater shrimp farm (Macaíba, RN), between September/2005 and February/2006, and in a freshwater shrimp farm (Ceará Mirim, RN), between May/2007 and September 2007. The samplings were collected weekly in saltwater farm and every fifteen days in freshwater farm. Total phosphorus, chlorophyll a and environmental parameters (pH, dissolved oxygen, salinity, temperature, depth and water transparency) were measured. Qualitative and quantitative analysis of the phytoplankton and bacterioplankton were carried out. The Shannon-Wiener ecologic indexes of diversity and the Pielou equitability indexes were calculated to the phytoplankton. Bacterial density was determined by epifluorescence microscopy. The data were statistically analyzed by Pearson correlation and t-Test. Chlorophycea were predominat in salt water and in the captation/drainage point (24 to 99%). Diatoms had higher wealth. The species Choricystis minor had the highest occurrence (100%) and dominance (90-100%), thus showing its adaptation to the high temperatures, salinity and low water transparency conditions. Filamentous Cyanobacteria like Oscillatoria sp., Pseudoanabaena sp. and Phormidium sp. had constant levels. The negative correlation between chlorophycea and water transparency, and the positive correlation between chlorophyll a and salinity, showed that the phytoplankton was well adapted to the low transparency and to the high salinity. The bacterioplankton was negatively correlated with the total phosphorus and salinity. In freshwater, Cyanobacteria were predominant (>80%), presenting some producers of toxins species like Microcystis sp., Aphanizomenon sp., Cylindrospermopsis raciborskii e Anabaena circinalis. Cyanobacterial density and total phosphorus and chlorophyll a concentrations exceeded the maximum value allowed by legislation. The means of total phosphorus varied from 264 to 627 Wg.L-1 and the means of chlorophyll a oscillated between 22 and 182 Wg.L-1. The phytoplankton species were selected by low availability of the light, high pH, temperature and high availability of total phosphorus. The bacterioplankton showed high densities (5,13 x 107 to 8,50 x107 Bac.mL-1). The studied environments (ponds and rivers) presented a high level of trophic state based on the high concentrations of chlorophyll a and total phosphorus and cyanobacteria dominance. The composition of species in the ponds and rivers was similar, as well as high concentrations of total phosphorus and chlorophyll a, highlighting the pollution caused by the discharges of the farms in natural environment

Análise metagenômica da microbiota de ambientes aquáticos do estado do Rio Grande do Norte - Brasil

The screening for genes in metagenomic libraries from soil creates opportunities to explore the enormous genetic and metabolic diversity of microorganisms. Rivers are ecosystems with high biological diversity, but few were examined using the metagenomic approach. With this objective, a metagenomic library was constructed from DNA soil samples collected at three different points along the Jundiaí-river (Rio Grande do Norte-Brazil). The points sampled are from open area, rough terrain and with the direct incidence of sunlight. This library was analyzed functionally and based in sequence. For functional analysis Luria-Bertani solid medium (LB) with NaCl concentration varied from 0.17M to 0.85M was used for functional analysis. Positives clones resistant to hypersaline medium were obtained. The recombinant DNAs were extracted and transformed into Escherichia coli strain DH10B and survival curves were obtained for quantification of abiotic stress resistance. The sequences of clones were obtained and submitted to the BLASTX tool. Some clones were found to hypothetical proteins of microorganisms from both Archaea and Bacteria division. One of the clones showed a complete ORF with high similarity to glucose-6-phosphate isomerase which participates in the synthesis of glycerol pathway and serves as a compatible solute to balance the osmotic pressure inside and outside of cells. Subsequently, in order to identify genes encoding osmolytes or enzymes related halotolerance, environmental DNA samples from the river soil, from the water column of the estuary and ocean were collected and pyrosequenced. Sequences of osmolytes and enzymes of different microorganisms were obtained from the UniProt and used as RefSeqs for homology identification (TBLASTN) in metagenomic databases. The sequences were submitted to HMMER for the functional domains identification. Some enzymes were identified: alpha-trehalose-phosphate synthase, L-ectoina synthase (EctC), transaminase L-2 ,4-diaminobutyric acid (EctB), L-2 ,4-diaminobutyric acetyltransferase (EctA), L-threonine 3 dehydrogenase (sorbitol pathway), glycerol-3-phosphate dehydrogenase, inositol 3-phosphate dehydrogenase, chaperones, L-proline, glycine betaine binding ABC transporter, myo-inositol-1-phosphate synthase protein of proline simportadora / PutP sodium-and trehalose-6-phosphate phosphatase These proteins are commonly related to saline environments, however the identification of them in river environment is justified by the high salt concentration in the soil during prolonged dry seasons this river. Regarding the richness of the microbiota the river substrate has an abundance of halobacteria similar to the sea and more than the estuary. These data confirm the existence of a specialized response against salt stress by microorganisms in the environment of the Jundiaí river

Uso de resíduo e de minerais de pegmatito da região do seridó RN e de argilas portuguesas em formulações de grês porcelanato

In the State Rio Grande do Norte, Brazil, the most significant deposits of minerals in the production of granite and pegmatite are Seridó region. Municipalities of Parelhas and Equador are the main responsible for the production of feldspar, quartz, kaolin and granite. The ceramic industries are always in search of competitiveness by investing in new products or improving existing techniques. The stoneware is a type of pottery that stands in the market because it presents technical and aesthetic characteristics superior to other existing products. Characteristics of the raw materials initially obtained with chemical analysis and mineralogical analysis are crucial in getting a product that satisfies the conditions in a manufacturing process and is, in principle, directly related to the firing cycle. This research aimed at developing new formulations for the mass production of ceramic stoneware. The raw materials initially characterized were feldspar, quartz, kaolin and granite. As part of the research was developed at the University of Aveiro, in Portugal, we used two clays used in the production of Portuguese ceramics. The raw material Brazilian and Portuguese and the final product, both in Portugal and Brazil, were analyzed for X-ray fluorescence, X-ray diffraction, granulometric analysis, dilatometric analysis, thermal analysis and analysis of scanning electron microscopy (MEV). The specimens prepared at the University of Aveiro (DECV) were sintered at 10000C and 12000C and the specimens prepared in UFRN were sintered at 10000C, 10500C, 11000C, 11500C, 12000C, 12500C and 13000C, but the best results and demonstrating the presence of the mineral mullite were at temperatures of 12000C, 12500C and 13000C. The results showed that the granite waste used may be considered raw material of excellent quality for use in the ceramic industry and coating floors and more accurately by the industry of stoneware. Physical and mechanical tests conducted on samples of the formulations F01 and F02 developed in UFRN showed a water absorption and mechanical strength suitable for the stoneware

Estudo do resíduo fosfogesso na formulação de uma pasta para revestimento interno de edifícios

Universidade Federal do Rio Grande do Norte

Análise do estado da arte dos aspectos diagnóticos, periciais e jurisprudenciais das LER/DORT no contexto previdenciário das doenças do trabalho no Brasil

Objetivo: analisar o estado da arte dos aspectos diagnósticos, periciais e jurisprudenciais das LER/DORT (Lesões por Esforços Repetitivos / Distúrbios Osteomusculares Relacionados ao Trabalho) no Brasil. Materiais e Método: trata-se de pesquisa descritiva, de natureza qualitativa, com formato documental, utilizando-se a técnica de análise de conteúdo. A avaliação evolutiva da legislação previdenciária relacionada as LER/DORT foi realizada através da pesquisa no banco de dados disponibilizado pelo Governo Federal e mediante a consulta ao DATAPREV/Sislex. A avaliação dos aspectos diagnósticos foi instrumentalizada através, principalmente, de artigos científicos publicados entre 2003 e 2008, nas línguas portuguesa, inglesa, espanhola e francesa, relacionados com os métodos de diagnósticos complementares das LER-DORT (ressonância magnética, tomografia computadorizada, ultrassonografia e eletroneuromiografia). As jurisprudências foram obtidas através da busca dos julgados sobre o tema, entre 2003 e 2008, pertencentes ao Supremo Tribunal Federal, Superior Tribunal de Justiça, Tribunais Regionais Federais, Tribunal Superior do Trabalho e Tribunais Regionais do Trabalho. Resultados: foram identificados 48 artigos abordando os aspectos diagnósticos das LER-DORT, observando-se que os exames por ressonância magnética, ultrassonografia e eletromiografia demonstraram ser mais efetivos, dentro das suas especificidades, para a complementação do exame clínico de patologias relacionadas às LER-DORT. A análise das 123 jurisprudências selecionadas demonstrou, de forma geral, que as LER-DORT equiparam-se ao acidente de trabalho, devendo apresentar nexo de causalidade (atestado através de laudo médico-pericial) e, ainda, ensejam a ação por danos morais, a qual, devido à EC nº 45 passou a ser competência da Justiça do Trabalho. O Estado da arte dos aspectos periciais encontra-se representado pela vigência da Instrução Normativa n. 98/2003, a qual traz como aspecto fundamental a determinação de novos parâmetros a serem considerados na definição de um quadro de LER-DORT, dispondo, ainda, sobre a conduta ética que deve ser adotada pelo médico perito, bem como chama a atenção para a necessidade dessas doenças do trabalho serem comunicadas às autoridadades competentes, através da emissão da Comunicação de Acidente de Trabalho (CAT). Conclusão: as LER-DORT representam, hoje, um problema de importante impacto, não apenas previdenciário, mas também econômico em diversos países, nos quais o Brasil encontra-se inserido. Estudos sobre o estado da arte relacionados às LER-DORT são fundamentais para auxiliar na construção de um modelo crítico e consciente que colabore com a garantia de sustentabilidade do sistema previdenciário no Brasil