β-Ti grain refinement via α-Precipitation

The present work explores the impact of α precipitates on β recrystallization following hot deformation of Ti-5Al-5Mo-5V-3Cr with grains larger than 1 mm. A single hot rolling pass of 36 pct reduction was conducted on an aged microstructure containing α precipitates at a temperature well below the β transus temperature. After annealing, a uniformly recrystallized structure with a grain size of ~100 µm is formed. The prior β grain boundaries can be readily identified and it is seen that the primary β grains have been replaced by grains displaying a spread of correlated misorientation angles extending up to the highest allowable values. The annealing comprises two stages. The first stage involves normal β subgrain growth limited by the Zener pinning force of the unstable α precipitates. The second stage corresponds to the onset of β recrystallization at the point where the Zener pinning force drops due to dissolution of the α precipitates. This leads to a uniform distribution of site saturated recrystallization nuclei.

Influence of z-pinning on the buckling of composite laminates under edge-wise compression

Z-pinning is a newly developed technique to enhance the strength of composite laminates in the thickness direction. Recent experimental and theoretical studies have shown that z-pins significantly improve mode I and mode II fracture toughness. In practice, buckling accompanying delamination is a typical failure mode in laminated composite structures. For a complete understanding of the z-pinning technique towards improvements of the overall mechanical properties of laminated composites, a numerical model is developed in this paper to investigate the influence of z-pins on the buckling composite laminates with initial delaminations under edge-wise compression. The numerical results indicate that z-pinning can indeed effectively increase the compressive strength of the composite laminates provided that the initial imperfection is within a certain range. The magnitude of the improvement is consistent with available experimental data.

Pinning down the elemental

Book review of 'The taste of river water' by Cate Kennedy.

A reevaluation of forces measured across thin polymer films : nonequillibrium and pinning effects

We have measured forces between molecularly smooth solid surfaces separated by thin films of molten polydimethylsiloxane. We show that a long-range repulsion reported in earlier work is not an equilibrium force, but can be attributed to viscous drag effects. Consistent with previous results, the viscosity of the film can be modeled by assuming that a layer of polymer molecules is immobilized or ‘‘pinned’’ at each surface for a time longer than the time scale of the measurements. We propose that this pinning is a result of entanglement-like effects in the vicinity of a wall.

Synchronization of singular Markovian jumping complex networks with additive time-varying delays via pinning control

Abstract
This study examines the problem of synchronization for singular complex dynamical networks with Markovian jumping parameters and two additive time-varying delay components. The complex networks consist of m modes which switch from one mode to another according to a Markovian chain with known transition probability. Pinning control strategies are designed to make the singular complex networks synchronized. Based on the appropriate Lyapunov-Krasovskii functional, introducing some free weighting matrices and using convexity of matrix functions, a novel synchronization criterion is derived. The proposed sufficient conditions are established in the form of linear matrix inequalities. Finally, a numerical example is presented to illustrate the effectiveness of the obtained results.

Grain size effect on behaviour and microstructure of a warm deformed Ti-IF steel

The effect of grain size on the deformation behaviour in the fenite region of a Titanium stabilized Interstitial Free steel was investigated by hot torsion. The initial work hardening regime is followed by a softening regime where a broad peak stress develops. The peak stress and the stress at final strain were relatively insensitive to grain size. However, at low values of the Zener-Hollomon parameter, the strain to the peak stress was strongly dependent on the grain size. A series of microstructural parameters were examined to explain these observations.

Grain size effect on the warm deformation behaviour of a Ti-IF steel

The effect of grain size on the warm deformation behaviour of a titanium stabilized interstitial free (IF) steel was investigated using hot torsion. The initial work hardening regime is followed by the development of a broad stress peak after which work softening occurs. The hypothetical saturation stress (Estrin–Mecking model) and the stress at final strain were relatively insensitive to grain size. However, the strain to the peak stress was strongly dependent on the grain size at low values of the Zener–Hollomon parameter. A simple phenomenological approach, using a combined Estrin–Mecking model and an Avrami type equation, was used to model the flow curves. The hypothetical saturation stress, the stress at final strain and the strain to peak stress were modelled using three different hyperbolic sine laws. A comparison with independent data from the literature shows that the apparent activation energy of deformation determined in this work (Q=372 kJ/mol) can be used to rationalize the steady-state stress in compression data found in the literature.

Static and metadynamic recrystallization of interstitial free steels during hot deformation

A rapid method was used to identify kinetics of the recrystallization for two IF (Interstitial Free) steels which have different phosphorous and boron contents. The static and metadynamic softening behaviour of the materials for a range of strain rates and temperatures were quantified. The critical strain for initiation of strain independent softening was estimated for the IF steels in respect to the time for 50 percent softening after deformation. The results showed that the strain for the initiation of strain independent softening (often referred to as metadynamic recrystallization) varies with the Zener Hollomon parameter. Classic static recrystallization was observed at strains below the strain independent softening for all processing conditions and the strain rate had a strong effect on the time for strain independent softening. Results also revealed that static and metadynamic recrystallization was delayed owing to the phosphorous and boron alloying elements. Hence, the large strain at above no-recrystallization temperature may be required for the early stage of Finishing Stands Unit (FSU) in hot strip rolling mills to initiate austenite grain refinement of phosphorous and boron added IF steels.

Numerical study of the mode I delamination toughness of Z-pinned laminates

A finite element (FE) model is developed to investigate mode I delamination toughness of z-pin reinforced composite laminates. The z-pin pullout process is simulated by the deformation of a set of non-linear springs. A critical crack opening displacement (COD) criterion is used to simulate crack growth in a double-cantilever-beam (DCB) made of z-pinned laminates. The toughness of the structure is quantified by the energy release rate, which is calculated using the contour integral method. The FE model is verified for both unpinned and z-pinned laminates. Predicted loading forces from FE analysis are compared to available test data. Good agreement is achieved. Our numerical results indicate that z-pins can greatly increase the mode I delamination toughness of the composite laminates. The influence of design parameters on the toughness enhancement of z-pinned laminates is also investigated, which provides important information to optimise and improve the z-pinning technique.