Formation of defects in the graphite oxidization process: a positron study

High-resolution positron annihilation lifetime (PAL) and two-detector coincidence Doppler broadening of annihilation radiation (2D-DBAR) measurements on graphite and its oxide derivatives for defect information, differing in oxidization agents, are reported. Positron measurements were found to be very effective in the investigation of defects in graphite and its derivatives. Positrons are mainly annihilated in vacancy-like defects on the particle surface and in large open-volume holes associated with the interface of graphite and graphite oxide. Different types of defects have been detected for unexfoliated graphite oxide and exfoliated graphene oxide based on 2D-DBAR measurements, namely the vacancy cluster and vacancy-oxygen complexes. It is also interesting to observe that the calculated large open-volume diameter of graphene oxide coincides with the distance between the layers from the XRD investigation, which indicates that the annihilation of the long-lived lifetime component τ3 might take place in the area between the graphene layers; no large open-volume hole has been detected.

Improvement of polypyrrole coating adhesion by radio frequency plasma

Tariq worked in the area of electronic textiles. He coated polyester fabric and PVDF films with polypyrrole. Plasma treatment was used to improve binding of coatings over the surface. He investigated in detail, the factors responsible for adhesion improvement using XPS, AFM, SEM, contact angle, abrasion tests and conductivity measurements. Different plasma gases, plasma power and plasma modes were investigated to get optimum bonding data. His investigations pointed towards improved surface oxygen functionalization and suitable surface morphology for improved bonding.

Water-soluble complexes of hydrophobically modified polymer and surface active imidazolium-based ionic liquids for enhancing oil recovery

The current study introduces the water-soluble complexes containing hydrophobically associating copolymer and a series of surface activity imidazolium-based ionic liquids (CnmimBr, n=6, 8, 10, 12, 14 and 16). The polymer, denoted as PAAD, was prepared with acrylamide (AM), acrylic acid (AA) and N,N-diallyl-2-dodecylbenzenesulfonamide (DBDAP). And the hydrophobic associative behavior of PAAD was studied by a combination of the pyrene fluorescence probe and viscosimetry. Incorporation of CnmimBr (n=10, 12, 14 and 16) in PAAD leaded to the white thick gel, while the pellucid solutions were obtained in complexes of PAAD and CnmimBr (n=6 and 8); addition of C6mimBr around critical micelle concentration resulted in a large decrease in viscosity of solution. Therefore, we particularly investigated the performance of PAAD/C8mimBr complex. The interfacial tension of PAAD/C8mimBr complex solution and crude oil under different conditions was examined. Moreover, PAAD/C8mimBr complex exhibited superior temperature resistance and shear reversible performance for enhancing oil recovery (EOR) by rheological test. The promising EOR of 21.65% can be obtained by PAAD/C8mimBr complex showing high potential to utilize this kind of new complex in EOR processes.

Quantifying turbulent mixing and oxygen fluxes in a Mediterranean-type, microtidal estuary

Experiments were carried out on an intermittent estuary during its closed (summer) and open (winter) states to identify the physical processes responsible for vertical mixing across the halocline, and to quantify vertical fluxes of oxygen and salt between water layers. During the blocked phase a two-layer structure was observed, with a brackish surface layer overlying old seawater. Within a deep basin the wind-driven turbulent mixing was consistent with the measured surface-layer turbulent dissipation, but the dissipation in the bottom layer appeared to be driven by internal seiching. In the shallow regions of the estuary vertical fluxes of dissolved oxygen were indicative of oxygen demand by respiration and remineralization of organic material in bottom water and sediments. During the estuary's open phase a three-layer structure was observed, having a fresh, river-derived surface layer, a middle layer of new seawater, and a bottom layer of old seawater. In the shallower regions surface-layer turbulent diffusion was consistent with the strong, gusty winds experienced at the time. The dissolved oxygen of the incoming seawater decreased to very low values by the time it reached the upstream deep basin as a result of the low cross-pycnocline oxygen flux being unable to compensate for the oxygen utilization. At least 50 % of the cross-pycnocline salt fluxes in the shallow reaches of the open estuary are suggested to be driven by Holmboe instabilities.

Beryllium (II) complexes of the klaui tripodal ligand cyclopentadienyltris (diethylphosphito-P) cobaltate(-)

The interactions of the beryllium(II) ion with the cyclopentadienyltris(diethylphosphito-P)cobaltate monoanion, L^-, have been investigated, in aqueous solution, by synthetic methods, potentiometry, ESMS, and ¹H, ³¹P, and ⁹Be NMR spectroscopy. L^- has been found able to displace either two or three water molecules in the beryllium(II) coordination sphere, to form mononuclear, dinuclear, and trinuclear derivatives, in which the metal ion is pseudotetrahedrally coordinated. The species [BeL(H₂O)]⁺ and [Be₂L₂(μ-OH)]⁺ have been identified in solution while complexes of formula BeL₂ and [Be₃L₄](ClO₄)₂ have been isolated as solid materials. The species [BeL(OPPh₂)]⁺, closely related to [BeL(H₂O)]⁺, has been characterized in acetone solution and isolated as tetraphenylborate salt. The structure of the unusual trimeric complex [Be₃L₄]²⁺ has been elucidated by an unprecedented 2D ⁹Be-³¹P NMR correlation spectrum showing the presence of a single central beryllium nucleus and two equivalent terminal beryllium nuclei. The three beryllium centers are held together by four cobaltate ligands, which display two different bonding modes: two ligands are terminally linked with all the three oxygen donors to one terminal beryllium, and the other two bridge two metal centers, sharing the oxygen donors between central and terminal beryllium atoms.

A calibration for surface analysis on aluminium alloys by RF-Glow-Discharge Optical Emission Spectrometry

Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].

Effects of atmospheric pressure plasma on dye uptake by the surface of wool

A woven pure wool fabric has been exposed to atmospheric pressure plasma for 30 seconds using a pilot-scale. commercial machine. X-ray photoelectron spectral data revealed large increases in oxygen and nitrogen. and a large reduction in carbon. on the surfaces of the plasma-treated fibres. A CIN ratio of 3.55 for plasma-treated wool was consistent with removal of the covalently-bound fatty acids from the surface of the cuticle cells. resulting in exposure of the proteinaceous epicuticle. Dye staining experiments revealed that the back of the fabric had received the same, uniform level of treatment as the face, despite the fact that only the face had been directly exposed to the plasma. Dyes (1 % oww) were applied to fabric at 50°C (liquor ratio =40: 1) and pH values from 3 to 6. The relatively low temperature of 50°C was selected in order to accentuate the effects of plasma on the rate of dye uptake. Under these conditions, dye was adsOibed onto the fibre surfaces, with very little penetration into the fibres. Effects of the plasma treatment on the rate of dyes adsorption were dyespecific. No significant effects of plasma on the rate of dye uptake were observed with relatively hydrophobic dyes, but hydrophilic dyes were adsorbed more rapidly by the plasmatreated fabric. It would appear that for more hydrophobic dyes, hydrophobic effects are more important for the adsorption of dyes by the plasma-treated fibres, even though these fibres were quite hydrophilic. On the other hand. it is concluded that for more hydrophilic dyes, electrostatic effects are more important for adsorption by the plasma-treated fibre.

Nanostructure and hydrogen bonding in interpolyelectrolyte complexes of poly(ε-caprolactone)-block-poly(2-vinyl pyridine) and poly(acrylic acid)

Nanostructured poly(ε-caprolactone)-block-poly(2-vinyl pyridine) (PCL-b-P2VP)/poly(acrylic acid) (PAA) interpolyelectrolyte complexes (IPECs) were prepared by casting from THF/ethanol solution. The morphological behaviour of this amphiphilic block copolymer/polyelectrolyte complexes with respect to the composition was investigated in a solvent mixture. The phase behaviour, specific interactions and morphology were investigated using differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, optical microscopy (OM), dynamic light scattering (DLS) and atomic force microscopy (AFM). Micelle formation occurred due to the aggregation of hydrogen bonded P2VP block and polyelectrolyte (PAA) from non-interacted PCL blocks. It was observed that the hydrodynamic diameter (D_h) of the micelles in solution decreased with increasing PAA content up to 40 wt%. After 50 wt% PAA content, D_h again increased. The micelle formation in PCL-b-P2VP/PAA IPECs was due to the strong intermolecular hydrogen bonding between PAA homopolymer units and P2VP blocks of the block copolymer. The penetration of PAA homopolymers into the shell of the PCL-b-P2VP block copolymer micelles resulted in the folding of the P2VP chains, which in turn reduced the hydrodynamic size of the micelles. After the saturation of the shell with PAA homopolymers, the size of the micelles increased due to the absorption of added PAA onto the surface of the micelles.

Exploring molecular changes at the surface of polypropylene after accelerated thermomolecular adhesion treatments

A central composite rotatable design (CCRD) method was used to investigate the performance of the accelerated thermomolecular adhesion process (ATmaP), at different operating conditions. ATmaP is a modified flame-treatment process that features the injection of a coupling agent into the flame to impart a tailored molecular surface chemistry on the work piece. In this study, the surface properties of treated polypropylene were evaluated using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). All samples showed a significant increase in the relative concentration of oxygen (up to 12.2%) and nitrogen (up to 2.4%) at the surface in comparison with the untreated sample (0.7% oxygen and no detectable nitrogen) as measured by XPS. ToF-SIMS and principal components analysis (PCA) showed that ATmaP induced multiple reactions at the polypropylene surface such as chain scission, oxidation, nitration, condensation, and molecular loss, as indicated by changes in the relative intensities of the hydrocarbon (C₃H₇⁺ , C₃H₅⁺ , C₄H₇⁺, and C₅H₉⁺), nitrogen and oxygen-containing secondary ions (C₂H₃O⁺, C₃H₈N⁺, C₂H₅NO⁺, C₃H₆NO⁺, and C₃H₇NO⁺). The increase in relative intensity of the nitrogen oxide ions (C₂H₅NO⁺ and C₃H₇NO⁺) correlates with the process of incorporating oxides of nitrogen into the surface as a result of the injection of the ATmaP coupling agent.

Tailoring the surface chemistry of carbon fiber and E-glass composites for improved adhesion

The main challenges in the manufacture of composite materials are low surface energy and the presence of silicon-containing contaminants, both of which greatly reduce surface adhesive strength. In this study, carbon fiber (CF) and E-glass epoxy resin composites were surface treated with the Accelerated Thermo-molecular adhesion Process (ATmaP). ATmaP is a multiaction surface treatment process where tailored nitrogen and oxygen functionalities are generated on the surface of the sample through the vaporization and atomization of n-methylpyrrolidone solution, injected via specially designed flame-treatment equipment. The treated surfaces of the polymer composites were analyzed using XPS, time of flight secondary ion mass spectrometry (ToF-SIMS), contact angle (CA) analysis and direct adhesion measurements. ATmaP treatment increased the surface concentration of polar functional groups while reducing surface contamination, resulting in increased adhesion strength. XPS and ToF-SIMS showed a significant decrease in silicon-containing species on the surface after ATmaP treatment. E-glass composite showed higher adhesion strength than CF composite, correlating with higher surface energy, higher concentrations of nitrogen and CO functional groups (from XPS) and higher concentrations of oxygen and nitrogen-containing functional groups (particularly C₂H₃O⁺ and C₂H₅NO⁺ molecular ions, from ToF-SIMS).

Highly selective and sensitive DNA assay based on electrocatalytic oxidation of ferrocene bearing zinc(II)-cyclen complexes with diethylamine

A highly selective and sensitive electrochemical biosensor has been developed that detects DNA hybridization by employing the electrocatalytic activity of ferrocene (Fc) bearing cyclen complexes (cyclen = 1,4,7,10-tetraazacyclododecane, Fc[Zn(cyclen)H2O]2(ClO4)4 (R1), Fc(cyclen)2 (R2), Fc[Zn(cyclen)H2O](ClO4)2 (R3), and Fc(cyclen) (R4)). A sandwich-type approach, which involves hybridization of a target probe hybridized with the preimmobilized thiolated capture probe attached to a gold electrode, is employed to fabricate a DNA duplex layer. Electrochemical signals are generated by voltammetric interrogation of a Fc bearing Zn−cyclen complexes that selectively and quantitatively binds to the duplex layers through strong chelation between the cyclen complexes and particular nucleobases within the DNA sequence. Chelate formation between R1 or R3 and thymine bases leads to the perturbation of base-pair (A−T) stacking in the duplex structure, which greatly diminishes the yield of DNA-mediated charge transport and displays a marked selectivity to the presence of the target DNA sequence. Coupling the redox chemistry of the surface-bound Fc bearing Zn−cyclen complex and dimethylamine provides an electrocatalytic pathway that increases sensitivity of the assay and allows the 100 fM target DNA sequence to be detected. Excellent selectivity against even single-base sequence mismatches is achieved, and the DNA sensor is stable and reusable.

Milk lactate determination with a rotating bioreactor based on an electron transfer mediated by osmium complexes incorporating a continuous-flow/stopped-flow system

The high sensitivity that can be attained using a bienzymatic system and mediated by the redox polymer [Os(bpy)₂ClPyCH₂NHpoly(allylamine)] (Os-PAA), has been verified by on-line interfacing of a rotating bioreactor and continuous-flow/stopped-flow/continuous-flow processing. When the hydrogen peroxide formed by LO_x layer reaches the inner layer, the electronic flow between the immobilized peroxidase and the electrode surface produces a current, proportional to lactate concentration. The determination of lactate was possible with a limit of detection of 5 nmol l⁻¹ in the processing of as many as 30 samples per hour. This arrangement allows working in undiluted milk samples with a good stability and reproducibility. Horseradish peroxidase [EC 1.11.1.7] and Os-PAA were covalently immobilized on the glassy carbon electrode surface (upper cell body), lactate oxidase [EC 1.1.3.x] was immobilized on a disk that can be rotated.

Enhanced oxygen permeation through perovskite hollow fibre membranes by methane activation

Hollow fibre membranes of mixed conducting perovskite La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF) were prepared via the combined phase inversion and sintering technique. The fibres were tested for air separation with a home-made reactor under the oxygen partial pressure gradient generated by the air/He streams. Some fibres were in situ activated by introducing methane in the He sweeping gas at high temperatures. The activated membranes with new morphology were created by transforming the inner densified surface layer to a porous structure. Compared to the original membranes, the activated gave appreciable higher oxygen fluxes. At 800 °C, the oxygen fluxes were increased by a factor of 10 after activation was carried out at 1000 °C for 1 h.