Finite element analysis of an axi-symmetric forward spiral extrusion of Mg-1.75Mn alloy

A potential severe plastic deformation process known as axi-symmetrical forward spiral extrusion (AFSE) has been studied numerically and experimentally. The process is based on the extrusion of cylindrical samples through a die with engraved spiral grooves in a near zero shape change manner. The process was simulated using a three dimensional finite element (FE) model that has been developed using commercial software, ABAQUS. In order to verify the finite element results, hot rolled and annealed samples of the alloy were experimentally processed by AFSE. The required extrusion forces during the process were estimated using the FE model and compared with the experimental values. The reasonable agreement between the FE results and experimental data verified the accuracy of the FE model. The numerical results indicate the linear strain distribution in the AFSE sample is only valid for a core concentric while the strain distribution in the vicinity of the grooves is non axi-symmetric. The FE simulation results from this research allows a better understanding of AFSE kinematics especially near the grooves, the required extrusion force and the resultant induced strain distribution in the sample. To compare the mechanical properties of the Mg-1.75Mn alloy before and after the process, a micro shear punch test was used. The tests were performed on samples undergoing one and four passes of AFSE. After four passes of AFSE, it was observed that the average shear strength of the alloy has improved by about 21%. The developedfinite element model enables tool design and material flow simulation during the process.

Finite element analysis of plastic deformation in variable lead axisymmetric forward spiral extrusion

A modified axisymmetric forward spiral extrusion (AFSE) has been proposed recently to enhance the strain accumulation during the process. The new technique is called variable lead axisymmetric forward spiral extrusion (VLAFSE) that features a variable lead along the extrusion direction. To assess the effect of design modification on plastic deformation, a comprehensive study has been performed here using a 3D transient finite element (FE) model. The FE results established the shear deformation as the dominant mode of deformation which has been confirmed experimentally. The variable lead die extends strain accumulation in the radial and longitudinal directions over the entire grooved section of the die and eliminates the rigid body rotation which occurs in the case of a constant lead die, AFSE. A comparison of forming loads for VLAFSE and AFSE proved the advantages of the former design in the reduction of the forming load which is more pronounced under higher frictional coefficients. This finding proves that the efficiency of VLAFSE is higher than that of AFSE. Besides, the significant amount of accumulated shear strain in VLAFSE along with non-axisymmetric distribution of friction creates a surface feature in the processed sample called zipper effect that has been investigated. © 2012 Springer Science+Business Media New York.

A study of plastic deformation during axisymmetric forward spiral extrusion and its subsequent mechanical property changes

Axisymmetric forward spiral extrusion (AFSE) accumulates large strains in its sample while extruding it through a die with engraved spiral grooves. A three-dimensional finite element model of AFSE has been developed using ABAQUS to investigate the deformation mode in detail, including the effect of groove geometry and the heterogeneity of plastic deformation. The numerical results demonstrated that the strain distribution in the AFSE sample cross section is linear in the radial direction within a concentric core while the distribution, outside the core, in the vicinity of the grooves is non-linear and non-axisymmetric. Mechanical properties and grain structure changes of the deformed sample were investigated. Improvements of mechanical properties in the processed samples can be attributed to the domination of the shear deformation mode in a plane normal to the extrusion axis and consequently the elongation of grains in the tangential direction

A kinematics study of variable lead axisymmetric forward spiral extrusion

Variable lead axi-symmetric forward spiral extrusion (VLAFSE) allows far more efficient strain accumulation than constant lead counterpart AFSE. It eliminates the rigid body rotation of the sample in an AFSE die which only causes frictional loss and has no contribution to the deformation. Based on a proposed velocity field, the kinematic formulation for VLAFSE is presented, utilized to predict strain components in the deformation zone and compared with experimental measurements. A simple closed form solution of the VLAFSE problem is presented which describes the flow of material inside the extrusion die. The results confirm that the effective strain of the process accumulates non-linearly in the both radial and extrusion directions.

Material properties under drawing and extrusion with cyclic torsion

A copper bar was drawn while a lead bar was extruded through a cyclically twisting die in a specifically designed experimental rig. The drawing/extrusion load fluctuated at the same frequency as that of die twisting. The load tended to be at a level of monotonic deformation when the die was changing direction. The degree of the reduction in load for both the drawing and extrusion processes depended on the deformation conditions and requires optimisation for industrial application.

The Εffects of censoring and the spiral of silence on focus group interviews: a case study of discussions on immigration

Focus groups assess the oral expressions of opinions of participants on a particular topic under discussion. They have several advantages over other qualitative research methodologies such as depth interviews because focus groups can discover people's attitudes and motivations while revealing the underlying views or values held by them. However, as focus groups elicit more socially expressed and contested opinions and discourses than Individual opinions, their discussions can be contaminated by the situational constraints and social pressures within the group. These include group dynamics, confonnity, censoring, the Group Leader Effect, the Groupthink Syndrome, the effects of the Spiral of Silence, characteristics of group members, and the climate of opinion within the group and in society at the time. This case study examines the effects of these factors on the 'horizontal interactions' between group members during a discussion with undecided voters about immigration, using two situations where focus group members took offence at comments made by another and challenged them, when the topic under discussion was personally relevant to them. Other members of the group, offending or otherwise, then remained silent, retracted their opinions to placate the challenger, and expressed neutral or conciliatory opinions in an effort to return the discussion to a state of equilibrium. It then examines some measures that can reduce such contaminations, including
methodological triangulation, where several methods and methodological
approaches are used to examine a given phenomenon, instead of just one method, such as the sole use of transcripts of focus group discussions.