Experimental study on strength and ductility of steel tubular stub columns filled with geopolymeric recycled concrete

Geopolymeric recycled concrete (GRC) is a new construction material which takes environmentalsustainability into account, by using alkali solution and fly ash to completely substitute Portland cementas well as by replacing natural coarse aggregate with recycled coarse aggregate. GRC could be used togetherwith steel hollow sections to form composite section. There is very limited study on such GRC filledtubular sections. This paper presents an experimental study on GRC filled tubular stub columns. A total of 12specimens were tested. The main parameters varied in the tests are: (1) two section sizes of square hollow sections(B × t) with 200mm×6mm and 150mm×5mm; (2) different concrete types: GRC and recycled aggregateconcrete (RAC); (3) different recycled aggregate (RA) replacement ratios of 0%, 50% and 100%. The relationshipof load versus axial strain was recorded and analysed to compare the ultimate strength and failuremechanism. Meanwhile, the ductility of the columns was investigated by a ductility index (DI). The resultsshow that the ultimate strength decreased with increasing RA contents for both GRC and RAC filled columns.The influence of RA content on the strength was greater in GRC than that in RAC. The effect of RA contenton the ductility of the columns was further investigated. Simulation method for predicting load versus strainrelationship is discussed for RAC and GRC filled steel tubular columns with different RA replacement ratios.

Recycled glass as a partial replacement for fine aggregate in structural concrete -effects on compressive strength

Waste management is becoming a major issue for communities worldwide. Glass, being nonbiodegradable, is not suitable for addition to landfill, and as such recycling opportunities need to be investigated. Due to the high material consumption of the construction industry, the utilisation of waste glass as a partial replacement for fine aggregate in structural concrete is particularly attractive. This project aimed to determine the level of glass replacement resulting in optimal compressive strength. Three concrete samples were tested at 7 and 28 days, for glass replacement proportions of 15, 20, 25, 30 and 40%. Compressive strength was found to increase up to a level of 30%, at which point the strength developed was 9% and 6% higher than the control after 7 and 28 days respectively. This demonstrates that concrete containing up to 30% fine glass aggregate exhibits higher compressive strength development than traditional concrete.

Recycled effluent irrigation in vineyards : an Australian case study. I. issues and monitoring

The viticultural industry is becoming an increasingly significant part of the Australian agricultural sector, with gross earnings of over $4 billion in 2002. Expansion of the industry in the last decade has been rapid, however its heavy reliance on irrigation has resulted in further expansion in many wine growing regions being limited by the availability of water. This problem is not confined to the viticultural industry, with ever increasing pressures on water resources worldwide. As demands for water continue to rise, new strategies to meet demands must be adopted. One of the strategies being increasingly employed is the recycling of waste waters for a number of applications such as irrigation and industrial uses. The use of recycled water for vineyard irrigation provides a number of benefits. Among them are the reduced demands on potable supplies, reduced waste discharges to surface waters, and the opportunity for expansion of production. Recycled waters however, contain constituents which have the potential to cause deleterious effects to both production and the environment. Therefore, the use of recycled water for irrigation requires targetted monitoring and management to ensure the long-term sustainability of both the vineyard and the surrounding environment. Traditional monitoring techniques including water quality monitoring and soil testing can be complimented by new technologies and techniques which provide large quantities of information with relatively less labour and time. Such techniques can be used to monitor the vineyard environment to identify impacts arising from management practices, allowing vineyard managers to adjust management for sustainable production

Variability of soil chemistry following irrigation with recycled municipal effluent: a Great Western vineyard case study

In areas of Australia where viticultural operations have been limited by lack of an acceptable irrigation water source, considerable expansion has occurred through the use of recycled wastewater. Despite this rapid expansion, little is known of the potential impacts of the water’s chemical constituents on soil properties, or the long-term sustainability of the vineyards using the water. In order to establish the impacts of drip irrigated recycled wastewater on a vineyard in Great Western, Australia, a study comparing the soils from the vineyard inter-row and row area was undertaken. Chemical and physical properties of the soil with varying distances from the drip emitter were also investigated. During the irrigation season, significant differences between the inter-row and row area were found for several chemical parameters including pH(1:5soil/water) (P<0.001), electrical conductivity (EC1:5) (P<0.001), water-soluble sodium (WS Na+) (P<0.001), and water-soluble chloride (WS Cl-) (P<0.001). This paper will discuss differences observed between soil properties of the inter-row and vine row area, as well as the spatial distribution of solutes under the drip emitter.

An analysis of factors influencing waste minimisation and use of recycled materials for the construction of residential buildings

Residential building construction activities, whether it is new build, repair or maintenance, consumes a large amount of natural resources. This has a negative impact on the environment in the form depleting natural resources, increasing waste production and pollution. Previous research has identified the benefits of preventing or reducing material waste, mainly in terms of the limited available space for waste disposal, and escalating costs associated with landfills, waste management and disposal and their impact on a  building company's profitability. There has however been little development internationally of innovative waste management strategies aimed at reducing the resource requirement of the construction process. The authors contend that embodied energy is a useful indicator of resource value. Using data provided by a regional high-volume residential builder in the State of Victoria, Australia, this paper identifies the various types of waste that are generated from the construction of a typical standard house. It was found that in this particular case, wasted amounts of materials were less than those found previously by others for cases in capital cities (5-10 per cent), suggesting that waste minimisation strategies are successfully being implemented. Cost and embodied energy savings from using materials with recycled content are potentially more beneficial in terms of embodied energy and resource depletion than waste minimisation strategies.

Strategy not tactics drives aggregate planning

The aggregate planning model supposedly shows how manufacturers cope with seasonally biased sales. Unfortunately, industry has failed to embrace any of the sophisticated algorithms that were developed to solve the corresponding resources allocation problem. This paper reveals why such methods have proven so unattractive. Aggregate planning is a chimera. In practice, planners construct the master production schedule directly, in line with a preferred production strategy. A “chase” plan is the most popular choice. When this option proves infeasible, management plumps for another predetermined strategy. The resultant stockpiling brings certain financial risks. However, companies take various measures to reduce their exposure.

Effect of fat replacement by insulin or lupin-kernal fibre on sausage patty acceptability, post-meal perceptions of satiety and food intake in men

The present study examined whether replacing fat with inulin or lupin-kernel fibre influenced palatability, perceptions of satiety, and food intake in thirty-three healthy men (mean age 52 years, BMI 27·4 kg/m²), using a within-subject design. On separate occasions, after fasting overnight, the participants consumed a breakfast consisting primarily of either a full-fat sausage patty (FFP) or a reduced-fat patty containing inulin (INP) or lupin-kernel fibre (LKP). Breakfast variants were alike in mass, protein and carbohydrate content; however the INP and LKP breakfasts were 36 and 37 % lower in fat and 15 and 17 % lower in energy density respectively compared with the FFP breakfast. The participants rated their satiety before breakfast then evaluated patty acceptability. Satiety was rated immediately after consuming the breakfast, then over the subsequent 4·5 h whilst fasting. Food consumed until the end of the following day was recorded. All patties were rated above ‘neither acceptable or unacceptable’, however the INP rated lower for general acceptability (P=0·039) and the LKP lower for flavour (P=0·023) than the FFP. The LKP breakfast rated more satiating than the INP (P=0·010) and FFP (P=0·016) breakfasts. Total fat intake was 18 g lower on the day of the INP (P=0·035) and 26 g lower on the day of the LKP breakfast (P=0·013) than the FFP breakfast day. Energy intake was lower (1521 kJ) only on the day of the INP breakfast (P=0·039). Both inulin and lupin-kernel fibre appear to have potential as fat replacers in meat products and for reducing fat and energy intake in men.

File replacement algorithm for storage resource managers in data grids

The main problem in data grids is how to provide good and timely access to huge data given the limited number and size of storage devices and high latency of the interconnection network. One approach to address this problem is to cache the files locally such that remote access overheads are avoided. Caching requires a cache-replacement algorithm, which is the focus of this paper. Specifically, we propose a new replacement policy and compare it with an existing policy using simulations. The results of the simulation show that the proposed policy performs better than the baseline policy.

Aggregate planning for seasonal demand : reconciling theory with practice

Purpose: The paper reports on the ramifications for production planning when monthly sales exhibit predictable seasonal highs and lows. The literature first acknowledged and dealt with the (aggregate planning) problem 50 years ago. Nevertheless, there is neither evidence that industry has adopted any of the mathematical techniques that were subsequently developed, nor a convincing explanation as to why not. Hence this research sets out to discover the methods manufacturers use to cope with seasonal demand, and how germane the published algorithms really are.

Design/methodology/approach: Forty-two case studies were compiled by interviewing senior managers and then conducting plant tours. No prior assumptions were made and the list of questions covered the gamut of production planning.

Findings: The main finding is that manufacturers select a straightforward production strategy, right from the outset, so the fundamental cost-balancing format is not relevant. The majority pick a “chase” strategy, since most organizations subscribe to a “just in time” ethos. Whenever a different strategy is preferred the rationale springs from skilled labour considerations or binding facilities constraints. The chosen strategy serves as a road map for resources acquisitions, and the master production schedule is constructed directly. So, the complex issue of how to disaggregate an optimal aggregate plan never even arises. Managers do not seek perfect solutions, but strive to eliminate, or contain, the most significant marginal costs. The nature of the business determines the most appropriate tactics to employ.

Originality/value: These findings break the mould as far as orthodox aggregate planning is concerned and show why theory is at odds with practice, whilst reaffirming the importance of concepts such as “flexibility”, “integration”, and “just-in-time production”.

Testosterone replacement therapy-perceptions of recipients and partners

Background. The androgenic hormones are important determinants of sexual behaviour in men. Testosterone replacement is important treatment for pituitary disease to maintain normal functioning. Although the physical effects of testosterone replacement have been well documented, little is known about the effects on relationships, particularly from the point of view of the sexual partners of men receiving testosterone replacement.

Aims. This paper reports a study exploring the perceptions of testosterone replacement on well-being and sexual functioning.

Methods. Semi-structured interviews were conducted with five men receiving testosterone implants (recipients), their permanent partners, and five recipients without partners. Recipient serum testosterone concentration was measured at 0, 1 and 4 months after testosterone implantation.

Results. The three groups reported similar effects of testosterone on well-being and sexual functioning. Recipient and partner ratings were also similar. Strength was less affected by decreasing testosterone concentration than energy in men with partners, but both strength and energy declined in men without partners. Decreased testosterone levels had a statistically significantly different effect on libido at time zero between men with and without partners (P < 0·015) and on ability to sustain an erection, but the ability to achieve an erection persisted over the 6 months in both male groups. Intercourse frequency increased from once per week at time 0 to ≥3 per week between 1 and 4 months after implant in men with partners. There were important effects of testosterone deficiency on general and sexual relationships, and these differed between men with partners and those without.

Conclusions. Testosterone has important physical and psychological benefits that may be related to the age at which testosterone replacement commences and the indications for its use. The small sample size may limit the ability to generalize the findings outside the study.

Effect of crude oil extracts from trout offal as a replacement for fish oil in the diets of the Australian native fish Murray cod Maccullochella peelii peelii

The efficacy of trout oil (TO), extracted from trout offal from the aquaculture industry, was evaluated in juvenile Murray cod Maccullochella peelii peelii (25.4-0.81 g) diets in an experiment conducted over 60 days at 23.7-0.8 °C. Five isonitrogenous (48% protein), isolipidic (16%) and isoenergetic (21.8 kJ gm1) diets, in which the fish oil fraction was replaced in increments of 25% (0-100%), were used. The best growth and feed efficiency was observed in fish fed diets containing 50-75% TO. The relationship of specific growth rate (SGR), food conversion ratio (FCR) and protein efficiency ratio (PER) to the amount of TO in the diets was described in each case by second-order polynomial equations (P<0.05), which were: SGR=-0.44TO2+0.52TO+1.23 (r2=0.90, P<0.05); FCR=0.53TO2-0.64TO+1.21 (r2=0.95, P<0.05); and PER=-0.73TO2+0.90TO+1.54 (r2=0.90, P<0.05). Significant differences in carcass and muscle proximate compositions were noted among the different dietary treatments. Less lipid was found in muscle than in carcass. The fatty acids found in highest amounts in Murray cod, irrespective of the dietary treatment, were palmitic acid (16:0), oleic acid (18:1n-9), linoleic acid (18:2n-6) and eicosapentaenoic acid (20:5n-3). The fatty acid composition of the muscle reflected that of the diets. Both the n-6 fatty acid content and the n-3 to n-6 ratio were significantly (P<0.05) related to growth parameters, the relationships being as follows. Percentage of n-6 in diet (X) to SGR and FCR: SGR=-0.12X2+3.96X-32.51 (r2=0.96) and FCR=0.13X2-4.47X+39.39 (r2=0.98); and n-3:n-6 ratio (Z) to SGR, FCR, PER: SGR=-2.02Z2+5.01Z-1.74 (r2=0.88), FCR=2.31Z2-5.70Z+4.54 (r2=0.93) and PER=-3.12Z2-7.56Z+2.80 (r2=0.88) respectively. It is evident from this study that TO could be used effectively in Murray cod diets, and that an n-3:n-6 ratio of 1.2 results in the best growth performance in Murray cod.

Superplasticity and cavitation of recycled AZ31 magnesium alloy fabricated by solid recycling process

Superplastic behaviour of Mg-alloy AZ31 was investigated to clarify the possibility of its use for superplastic forming (SPF) and to accurately evaluate material characteristics under a biaxial stress by utilizing a multi-dome test. The material characteristics were evaluated under three different superplastic temperatures , 643, 673, and 703 K in order to determine the most suitable superplastic temperature. Finite Element Method (FEM) simulation of rectangular pan forming was carried out to predict the formability of the material into a complex shape. The superplastic material properties are used for the simulation of a rectangular pan. Finally, the simulation results are compared with the experimental results to determine the accuracy of the superplastic material characteristics. The experimental results revealed that the m values are greater than 0.3 under the three superplastic temperatures, which is indicative of superplasticity. The optimum superplastic temperature is 673 K, at which a maximum m value and no grain growth were observed. The results of the FEM simulation revealed that certain localized thinning occurred at the die entrance of the deformed rectangular pan due to the insufficient ductility of the material. The simulation results also showed that the optimum superplastic temperature of AZ31 is 673 K.