Corrosion properties of a RF-magnetron-sputtered TiN coating deposited on 316L stainless steel

The effect of rf-power in the range from 100 to 200 W on the electrochemical properties of TiN coatings deposited on 316L stainless steel was investigated by using various electrochemical techniques in a 3.5-wt\% NaCl solution. Surface analyses were also conducted to analyze the coating characteristics. X-ray diffraction (XRD) and atomic force microscopy (AFM) analyses confirmed that increasing the rf-power led to a preferred orientation of the TiN(200) microstructure and decreased the surface roughness. The potentiodynamic test results confirmed the passive behavior of all of the specimens with low passive current densities and demonstrated that the effective pitting resistance of the TiN coatings increased with increasing rf-power. The electrochemical impedance spectroscopy (EIS) tests showed that the TiN films deposited with high rf-power had excellent corrosion resistance during an immersion time of 720 h due to their high total resistance and low porosity.

Graphene quantum dots directly generated from graphite via magnetron sputtering and the application in thin-film transistors

This work presents a novel method to prepare graphene quantum dots (GQDs) directly from graphite. A composite film of GQDs and ZnO was first prepared using the composite target of graphite and ZnO via magnetron sputtering, followed with hydrochloric acid treatment and dialysis. Morphology and optical properties of the GQDs were investigated using a number of techniques. The as-prepared GQDs are 4-12 nm in size and 1-2 nm in thickness. They also exhibited typical excitation-dependent properties as expected in carbon-based quantum dots. To demonstrate the potential applications of GQDs in electronic devices, pure ZnO and GQD-ZnO thin-film transistors (TFTs) using ZrOx dielectric were fabricated and examined. The ZnO TFT incorporating the GQDs exhibited enhanced performance: an on/off current ratio of 1.7 × 107, a field-effect mobility of 17.7 cm2/Vs, a subthreshold swing voltage of 90 mV/decade. This paper provides an efficient, reproducible and eco-friendly approach for the preparation of monodisperse GQDs directly from graphite. Our results suggest that GQDs fabricated using magnetron sputtering method may envision promising applications in electronic devices.

Electrochemical behavior of CrN coating for polymer electrolyte membrane fuel cell

CrN films on a bipolar plate in polymer electrolyte membrane fuel cells have several advantages owing to their excellent corrosion resistance and mechanical properties. Three CrN samples deposited at various radio frequency (RF) powers by RF magnetron sputtering were evaluated under potentiodynamic, potentiostatic and electrochemical impedance spectroscopy conditions. The electrochemical impedance spectroscopy data were monitored for 168 h in a corrosive environment at 70 °C to determine the coating performance at +600 mV_SCE under simulated cathodic conditions in a polymer electrolyte membrane fuel cell. The electrochemical behavior of the coatings increased with decreasing RF power. CrN films on the AISI 316 stainless steel substrate showed high protective efficiency and charge transfer resistance, i.e. increasing corrosion resistance with decreasing RF power. X-ray diffraction confirmed the formation of a CrN(200) preferred orientation at low RF power.

X-ray diffraction line broadening from gold and platinum thin films

X-ray diffraction line profile analysis has been used to study the microstructure of (Ill) oriented gold and platinum thin films deposited by thermal evaporation and DC magnetron sputtering. In addition to crystallite size broadening, the profiles from these films displayed broadening arising from dislocations. A parallel investigation, using transmission electron microscopy (TEM) was undertaken to study the nature of dislocations formed, and to provide information on the dimensions of the crystallite columns in the films. X-ray data were collected at room temperature to determine the anisotropy of the broadening with (hkl), using a Siemens D5000 powder diffractometer (CuKa radiation) and two high-resolution synchrotron instruments (BM 16 at the ESRF [A=0.35A] and station 2.3 at the Daresbury laboratory. Two approaches to instrument deconvolution were investigated; Fourier deconvolution and fundamental parameters profile fitting, using Lab6 as a reference material to determine the instrument profile function. After removal of the crystallite size broadening contribution from the measured integral breadths, the residual microstrain broadening was modelled assuming dislocations based on a FCC a/2<110>{ Ill} slip system. The results of the X-ray analysis agreed with dark field TEM micrographs, which showed that many of the crystallites contained dislocations of mixed character (screw- edge).

Localization with orientation using RSSI measurements: RF map based approach

Localization of RFIDs in the indoor environment will entail determining both the position and the orientation of the user. This paper develops estimator using RSSI measurements to predict the position and orientation of a transmitter in an indoor environment. The best estimator tried was an K-nearest neighbours model that gave an accuracy of approximately 83% for position prediction and 93% for orientation prediction. It was also found that the RSSI values change throughout the day, meaning that an adaptive estimator is necessary for localization.

A calibration for surface analysis on aluminium alloys by RF-Glow-Discharge Optical Emission Spectrometry

Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].

RF communication between surface and underwater robotic swarms

In order for underwater robots to communicate with land and air based robots on an equal basis, high speed communications is required. If the robots are not to be tethered then wireless communications is the only possibility. Sonar communications is too slow. Unfortunately radio waves are rapidly attenuated under water due to phenomena such as skin depth. These experiments attempt to extend the range of underwater radio communications.

Pi-shaped MEMS architecture for lowering actuation voltage of RF switching

A wide band low actuation capacitive coupling electrostatic RF MEMS switching device is presented in this paper. The device includes a pi-shaped matching architecture containing two switches connected by a high impedance short transmission line. The device can act as a switch for any desired frequency whilst requiring only 12volts for actuation. By optimizing the length and the characteristic impedance of the transmission line, the switch can be tailored for desired frequency bands. The switch is calculated and simulated for Ka to V frequency bands demonstrating excellent improvements of RF characteristics.