Direct observation of defect levels in hexagonal BN by soft X-ray absorption spectroscopy

Formation of defects in hexagonal boron nitride under low-energy argon bombardment has been studied by near-edge X-ray absorption fine structure (NEXAFS) around B and N K-edges. Breaking of B-N bonds and creation of nitrogen vacancies has been identified from the B K-edge, followed by the formation of molecular nitrogen, N2, at interstitial positions. The presence of N2 produces a sharp resonance in the low-resolution NEXAFS spectra around N K-edge, showing the characteristic vibrational fine structure in high-resolution measurements. Several new peaks in NEXAFS spectra have been assigned to boron or nitrogen interstitials, in good agreement with theoretical predictions. © 2009 Elsevier B.V. All rights reserved.

Effects of plasma treatment of wool on the uptake of sulfonated dyes with different hydrophobic properties

A wool fabric has been subjected to an atmospheric-pressure treatment with a helium plasma for 30 seconds. X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry confirmed removal of the covalently-bound fatty acid layer (F-layer) from the surface of the wool fibers, resulting in exposure of the underlying, hydrophilic protein material. Dye uptake experiments were carried out at 50 ºC to evaluate the effects of plasma on the rate of dye uptake by the fiber surface, as well as give an indication of the adsorption characteristics in the early stages of a typical dyeing cycle. The dyes used were typical, sulfonated wool dyes with a range of hydrophobic characteristics, as determined by their partitioning behavior between water and n-butanol. No significant effects of plasma on the rate of dye adsorption were observed with relatively hydrophobic dyes. In contrast, the relatively hydrophilic dyes were adsorbed more rapidly (and uniformly) by the plasma-treated fabric. It was concluded that adsorption of hydrophobic dyes on plasma-treated wool was influenced by hydrophobic interactions, whereas electrostatic effects predominated for dyes of more hydrophilic character. On heating the dyebath to 90 ºC in order to achieve fiber penetration, no significant effect of the plasma treatment on the extent of uptake or levelness of a relatively hydrophilic dye was observed as equilibrium conditions were approached.

Influence of calcium ion deposition on apatite-inducing ability of porous titanium for biomedical applications

In the present study, the influence of calcium ion deposition on the apatite-inducing ability of porous titanium(Ti) was investigated in a modified simulated body fluid (m-SBF). Calcium hydroxide (Ca(OH)₂) solutions with five degrees of saturation were used to hydrothermally deposit Ca ions on porous Ti with a porosity of 80%. Apatite-inducing ability of the Ca-ion-deposited porous Ti was evaluated by soaking them in m-SBF for up to 14 days. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) confirmed that a thin layer of calcium titanate (CaTiO₃)/calcium oxide (CaO) mixture with a nanostructured porous network was produced on porous Ti substrates after hydrothermal treatment at 200 °C for 8 h. X-ray photoelectron spectroscopy results demonstrated that the content of the Ca ions deposited on Ti and the thickness of the CaTiO₃/CaO layer increased with increasing saturation degree of the Ca(OH)₂ solution. The thickest (over 10 nm) CaTiO₃/CaO layer with the highest Ca content was achieved on the Ti treated in an oversaturated Ca(OH)₂ solution (0.2 M). SEM, XRD, transmission electron microscopy and Fourier transformed infrared spectroscopy analysis indicated that the porous Ti samples deposited with the highest content of Ca ions exhibited the best apatite-inducing ability, producing a dense and complete carbonated apatite coating after a 14 day soaking in m-SBF. The present study illustrated the validity of using Ca ion deposition as a pre-treatment to endow desirable apatite-inducing ability of porous Ti for bone tissue engineering applications.

The characterization and chemical reactivity of powdered wool

Wool powders with various particle sizes have been produced using different milling techniques. Scanning electron microscopy (SEM) showed gradual breakdown of the fibre as it was progressively converted into powder form. Chlorination enhanced the effectiveness of subsequent air-jet milling. X-ray photoelectron spectroscopy (XPS) revealed an increase in the surface concentrations of oxygen and nitrogen, and a decrease in carbon and sulphur on conversion of the fibres into powders, as the cortex became exposed on the powder surface. An increased surface concentration of cysteic acid was observed for the chlorinated powder. Rapid uptake of dye by wool powders was observed in situations where there was virtually no uptake by the original fibre. Hydrophobic dyes were more readily sorbed than were hydrophilic dyes. The chlorination treatment led to a decrease in the sorption of acid dyes. Confocal microscopy, used in conjunction with a fluorescent stain, showed that chemicals were able to penetrate wool particles, even at room temperature. The rate and extent of uptake of dye by the finer powders were comparable to that obtained with activated charcoal, even though the surface area of the charcoal was 100 times greater.

An XRD/XPS approach to structural change in conducting PPy

Electrochemically synthesised polypyrrole (PPy) with 1,5 naphthalene disulfonate (1,5-NDS) counterions treated with simple acid and base was characterised using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The as synthesised film was found to be amorphous with short-range ordering in the polymer backbone. Ordering was lost after thermal ageing with evidence of counterion degradation. Base treatment lead to loss of ordering as well as dedoping of the polymer whereas acid treatment at high temperature increases short range ordering. Conductivity was also increased dramatically with evidence of ion exchange. Ordering induced by the treatment was maintained even after thermal ageing.

Mechanisms governing the enhanced thermal stability of acid and base treated polypyrrole

One of the major problems associated with the use of polypyrrole (PPy) in a practical engineering application is its poor thermal stability at elevated temperatures, especially in the presence of oxygen and moisture. Several authors have shown that enhanced stability can be achieved through treatment with simple acids and bases. This paper presents a summary of the possible structural changes which occur as a result of these treatments and those that appear to be related to enhanced conductivity stability. A slight increase in conductivity (10–20%) is observed for acid treated PPy films which is found to be the result of protonation of the pyrrole structure. This effect is dramatically enhanced by treatment at high temperatures where an increase in conductivity of >84% can be achieved. Base treatment of the PPy films results in the deprotonation of the pyrrole structure leading to the loss of conductivity (>40%). Preliminary X-ray Photoelectron Spectroscopy (XPS) results indicate that both acid and base treatment resulted in the elimination of reactive sites for oxygen. Long term thermal ageing of these treated films were conducted at 150 °C in air. The conductivity decay behaviour was found to follow multiple first order chemical reaction kinetics.

Modification of thermoplastic coatings for improved cathodic disbondment performance on a steel substrate : a study on failure mechanisms

The effect of blending two different materials with a medium density polyethylene for use as pipe coatings is presented. The influence of such blending on properties such as cathodic disbondment (CD) and wet adhesion on steel is investigated. The components blended include a functionalised polyethylene (PE) containing the polar functionality, maleic anhydride (MAH) and an amorphous elastomer, ethylene-propylene-diene terpolymer (EPDM). It was found that modification of PE with small amount (2.5–3 wt%) of either blended MAH-g-PE or EPDM resulted in a significant improvement in CD performance and wet adhesion strength. The mode of failure and disbondment mechanism was investigated using energy dispersive X-ray spectroscopy (EDXS) and X-ray photoelectron spectroscopy (XPS). The greater resistance of migration of sodium ions increases with the incorporation of the modifiers, and it is proposed that this results in an increase in CD performance.

Exploring molecular changes at the surface of polypropylene after accelerated thermomolecular adhesion treatments

A central composite rotatable design (CCRD) method was used to investigate the performance of the accelerated thermomolecular adhesion process (ATmaP), at different operating conditions. ATmaP is a modified flame-treatment process that features the injection of a coupling agent into the flame to impart a tailored molecular surface chemistry on the work piece. In this study, the surface properties of treated polypropylene were evaluated using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). All samples showed a significant increase in the relative concentration of oxygen (up to 12.2%) and nitrogen (up to 2.4%) at the surface in comparison with the untreated sample (0.7% oxygen and no detectable nitrogen) as measured by XPS. ToF-SIMS and principal components analysis (PCA) showed that ATmaP induced multiple reactions at the polypropylene surface such as chain scission, oxidation, nitration, condensation, and molecular loss, as indicated by changes in the relative intensities of the hydrocarbon (C₃H₇⁺ , C₃H₅⁺ , C₄H₇⁺, and C₅H₉⁺), nitrogen and oxygen-containing secondary ions (C₂H₃O⁺, C₃H₈N⁺, C₂H₅NO⁺, C₃H₆NO⁺, and C₃H₇NO⁺). The increase in relative intensity of the nitrogen oxide ions (C₂H₅NO⁺ and C₃H₇NO⁺) correlates with the process of incorporating oxides of nitrogen into the surface as a result of the injection of the ATmaP coupling agent.

Single molecule conductance through rigid norbornylogous bridges with zero average curvature

A new homologous series of norbornylogous (NB) bridges has been synthesized in which the average curvature of the bridges is very small. The molecules are rigid and have two thiol moieties at each end to allow them to form self-assembled monolayers (SAMs) and to connect to two gold electrodes to form a molecular junction. The SAMs formed were characterized using electrochemistry to determine the surface coverage of molecules on gold surface and to provide an indication of the packing of the NB bridges while ellipsometry and X-ray photoelectron spectroscopy (XPS) were used to provide an indication of the SAM thickness and orientation. Single molecule conductance of NB bridges was measured as a function of the molecular length. The conductance was found to decrease exponentially with the length with a decay constant that is exactly correlated with photoelectron transfer and other studies at the multiple molecule level. The molecule−electrode contact resistance was determined and compared with that of related alkanedithiol molecular junctions.

Characterisation of gold electrodes modified with self-assembled monolayers of l-cysteine for the adsorptive stripping analysis of copper

Electrochemical sensors for copper ions in environmental samples were prepared by modifying gold electrodes with l-cysteine by self-assembly. The adsorption of l-cysteine on gold electrodes was studied by electrochemical reductive desorption in 0.5 M KOH, and the interaction of l-cysteine with copper ions was investigated by cyclic voltammetry, chronoamperometry and X-ray photoelectron spectroscopy. At low concentrations the ratio of l-cysteine to bound Cu(II) is 2:1. At higher concentrations (0.1 M) copper reacts with adsorbed cysteine forming copper sulfide on the electrode surface. On a modified l-cysteine gold electrode, Osteryoung square wave voltammetric determination of Cu(II) with a detection limit below 5 ppb has been demonstrated.

pH-detachable polymer brushes formed using titanium−diol coordination chemistry and living radical polymerization (RAFT)

pH-detachable poly(styrene) brushes formed on indium−tin oxide (ITO) glass substrates using metal complex chemistry and reversible addition−fragmentation chain transfer (RAFT) polymerization was described. These pH-detachable polymeric brushes were generated using both “graft-from” and “graft-to” methodologies. The methodologies involved either the surface self-assembly of catechol-functional RAFT agents (graft-from) or catechol-terminal polymer chains (graft-to) onto the ITO substrate via titanium−diol coordination. The stepwise functionalization of the ITO glass surfaces was characterized successfully using X-ray photoelectron spectroscopy (XPS) and contact angle measurement. Poly(styrene) brushes generated using the “graft-from” method were denser than those generated using the “graft-to” method, as exemplified by atom force microscopy (AFM) and quantified using cyclic voltammetry. Poly(styrene) brushes assembled using both methods could be detached easily by manipulating the pH of the brush environment. Cyclic voltammetry was utilized to calculate precisely the surface coverage of the RAFT functionality and polymeric brush density.

Synthesis, characterization, and multilayer assembly of pH sensitive graphene−polymer nanocomposites

pH sensitive graphene−polymer composites have been prepared by the modification of graphene basal planes with pyrene-terminated poly(2-N,N′-(dimethyl amino ethyl acrylate) (PDMAEA) and poly(acrylic acid) (PAA) via π−π stacking. The pyrene-terminal PDMAEA and PAA were synthesized using reversible addition−fragmentation chain transfer (RAFT) polymerization with a pyrene-functional RAFT agent. The graphene−polymer composites were found to demonstrate phase transfer behavior between aqueous and organic media at different pH values. Atomic force microscopy (AFM) analysis revealed that the thicknesses of the graphene−polymer sheets were approximately 3.0 nm when prepared using PDMAEA (M_n: 6800 and PDI: 1.12). The surface coverage of polymer chains on the graphene basal plane was calculated to be 5.3 × 10⁻¹¹ mol cm⁻² for PDMAEA and 1.3 × 10⁻¹⁰ mol cm⁻² for PAA. The graphene−polymer composites were successfully characterized using X-ray photoelectron spectroscopy (XPS), attenuated total reflection infrared (ATR-IR) spectroscopy, and thermogravimetric analysis (TGA). Self-assembly of the two oppositely charged graphene−polymer composites afforded layer-by-layer (LbL) structures as evidenced by high-resolution scanning electron microscopy (SEM) and quartz crystal microbalance (QCM) measurements.

New approach to controllable nitrogen doping for improved nano-semiconductors

The data covers the following:
X-ray photoelectron spectroscopy (XPS) - to collect surface chemical structure changes (using RMIT instrument);
Scanning electron microscopy (SEM) - to collect surface physical structure changes;
Atomic force microscopy (AFM) - to collect surface morphology changes;
Internal/External quantum efficiency (IQE/EQE) – to collect DSSC (Dye Sensitised Solar Cells) efficiency data;
Discharge/Charge capacity - to collect battery efficiency data.