Compressibility of porous magnesium foam: dependency on porosity and pore size

Mechanical properties of porous magnesium with the porosity of 35–55% and the pore size of about 70–400 μm are investigated by compressive tests focusing on the effects of the porosity and pore size on the Young's modulus and strength. Results indicated that the Young's modulus and peak stress increase with decreasing porosity and pore size. The mechanical properties of the porous magnesium were in a range of those of cancellous bone. Therefore, it is suggested that the porous magnesium is one of promising scaffold materials for hard tissue regeneration.

Effects of pore morphology on the compressive behaviour of porous metals

In the present study, porous nickel foams with three different porosities (i.e. 50 %, 60 % and 70 %) were fabricated using the space-holding sintering method. Ammonium bicarbonate particles with sizes ranging from 1- 2 mm were chosen as the space-holding material. The anisotropic behaviours of the nickel foam samples were investigated by compressive testing loading at different directions, i.e., in both directions of the major and minor axis of ellipsoidal cells. Electron scanning microscopy (SEM) and Image-Pro Plus was used to characterise the morphological characteristics of the porous nickel foam samples. Results indicated that the porous nickel foam samples exhibited obvious anisotropic mechanical properties. The foam sample shows significantly higher nominal stress for loading in the direction of the major axis of the pores than loading in the direction of the minor axis of pores. The nominal stress increases with the decreasing of the porosity.

Effect of pore size on mechanical properties of titanium foams

In the study, both experimental work and numerical modeling are performed to investigate the pore size effects on the mechanical properties and deformation behaviours of titanium foams. Cylindrical titanium foam samples with different pore sizes are fabricated through powder metallurgy. Scanning electron microscope (SEM) is used to determine the pore size, pore distribution and the ratios of the length to width of pores. Compressive tests are carried out to determine the mechanical properties of the titanium foams with different pore sizes. Finally, finite element modeling is attempted to simulate the deformation behaviour and the mechanical properties of the titanium foams. Results indicate that titanium foams with different pore sizes have different geometrical characteristics, which lead to different deformation behaviours of cell walls during compression, resulting in different mechanical properties of titanium foams.

Possible changes of pore size during nanofiltration

The textile industry plays an important role in the world economy as well as our daily life. However, the industry consuming a large quantity of water and generating huge amount of wastewater are unsustainable to the conservation of our precious resources and environment and need improvement. The wastewater, especially the one from spent cotton reactive dyebaths, contains high salt content, various dyes and high alkalinity. This study was carried out to investigate the feasibility of membrane filtration treating spent cotton reactive dye baths. A stirred cell with nanofiltration membrane was used aiming at reusing the reclaimed water. Spent dyebath solutions were synthesized containing hydrolyzed C. I. Reactive Black 5 and sodium chloride. When a piece of membrane was used repeatedly it was expected the flux would decrease after each usage due to fouling of impurities. However, it was found that the water flux increased while dye rejection decreased after each run. At pH 10, the dye rejection decreased significantly. It was proposed that the pore sizes of membrane might have changed during membrane filtration. An equation was derived calculating the possible changes of pore sizes.

Evidence of changes in membrane pore characteristics due to filtration of dye bath liquors

This study was carried out to investigate the treatment of various salt solutions and synthetic dye bath liquors by nanofiltration using Nanomax-50 membrane in a stirred cell with 150 mL working volume. Donnan exclusion was compared by filtering salts with monovalent and divalent cations and anions. This was done by comparing three salts including sodium chloride (NaCl), calcium chloride (CaCl2) and sodium sulphate (Na2SO4). The rejection order determined was Na2SO4>NaCl>CaCl2 which is typical of a negatively charged membrane where Donnan and steric exclusion play an important role in separation. Studies on the flux and rejection characteristics of sodium sulphate were undertaken for concentrations ranging from 10 to 40 gl−1 thereby replicating actual dye bath salt concentrations. Synthetic dye bath liquors were prepared using acidic dye (Acid Green 25) at a fixed concentration of 100 mgl−1 with 10 and 15 gl−1 of sodium sulphate solutions. While, the results showed evidence of flux decline due to increased resistance and decreased transmembrane pressure, pore enlargement occurred after the filtration experiments with sodium sulphate solutions greater than 20 gl−1. Pore enlargement was even more prominent in the two synthetic dye bath liquors filtered. Pore enlargement was determined by observing the pure water flux before and after filtering sodium sulphate solutions or dye bath liquors. An increase in pore diameter of 58 and 94 %was estimated when dye bath liquors containing 10 and 15 gl−1 of sodium sulphate, respectively were filtered through the membrane. The following equation was derived in estimating the pore enlargement, where de1 and de2 are the apparent diameter of membrane pore sizes before and after filtration of salt solutions or dye bath liquors and Rm1 and Rm2 are the membrane resistance of pure water flux before and after filtration of salt solutions or dye bath liquors. These results have important implications for the application of nanofiltration technology to textile wastewater treatment and reuse.

Immobilization of large, aliovalent cations in the small-pore zeolite K-natrolite by means of pressure

High-pressure ion exchange of small-pore zeolite K-natrolite allows immobilization of nominally non-exchangeable aliovalent cations such as trivalent europium. A sample exchanged at 3.0(1) GPa and 250 °C contains about 4.7 Eu^III ions per unit cell, which is equivalent to over 90 % of the K⁺ cations being exchanged.

Pressure- and heat-induced insertion of CO2 into an auxetic small-pore zeolite

When the small-pore zeolite natrolite is compressed at ca. 1.5 GPa and heated to ca. 110 °C in the presence of CO₂, the unit cell volume of natrolite expands by 6.8% and ca. 12 wt % of CO₂ is contained in the expanded elliptical channels. This CO₂ insertion into natrolite is found to be reversible upon pressure release.