Characterization and evaluation of BaCo0.7Fe0.2Nb0.1O3−δ as a cathode for proton-conducting solid oxide fuel cells

This study characterizes BaCo0.7Fe0.2Nb0.1O3−δ (BCFN) perovskite oxide and evaluates it as a potential cathode material for proton-conducting SOFCs with a BaZr0.1Ce0.7Y0.2O3-δ (BZCY) electrolyte. A four-probe DC conductivity measurement demonstrated that BCFN has a modest electrical conductivity of 2–15 S cm−1 in air with p-type semiconducting behavior. An electrical conductivity relaxation test showed that BCFN has higher Dchem and Kchem than the well-known Ba0.5Sr0.5Co0.8Fe0.2O3−δ oxide. In addition, it has relatively low thermal expansion coefficients (TECs) with values of 18.2 × 10−6 K−1 and 14.4 × 10−6 K−1 at temperature ranges of 30–900 °C and 30–500 °C, respectively. The phase reaction between BCFN and BZCY was investigated using powder and pellet reactions. EDX and XRD characterizations demonstrated that BCFN had lower reactivity with the BZCY electrolyte than strontium-containing perovskite oxides such as SrCo0.9Nb0.1O3-δ and Ba0.6Sr0.4Co0.9Nb0.1O3−δ. The impedance of BCFN was oxygen partial pressure dependent. Introducing water into the cathode atmosphere reduced the size of both the high-frequency and low-frequency arcs of the impedance spectra due to facilitated proton hopping. The cathode polarization resistance and overpotential at a current density of 100 mA cm−2 were 0.85 Ω cm−2 and 110 mV in dry air, which decreased to 0.43 Ω cm−2 and 52 mV, respectively, in wet air (∼3% H2O) at 650 °C. A decrease in impedance was also observed with polarization time; this was possibly caused by polarization-induced microstructure optimization. A promising peak power density of ∼585 mW cm−2 was demonstrated by an anode-supported cell with a BCFN cathode at 700 °C.

Immunolocalisation of sodium/proton exchanger-like proteins in the gills of elasmobranchs

Na⁺/H⁺ exchangers are integral membrane proteins that exchange Na⁺ and H⁺ across cell membranes. The Na⁺/H⁺ exchangers 2 and 3 are epithelial isoforms in mammals and contribute to acid–base homeostasis. The gills of fishes, including elasmobranchs, are also associated with acid/base balance, and are probably the primary acid/base regulatory organ. This study examines the presence of Na⁺/H⁺ exchangers 2 and 3 using immunohistochemistry and immunoblotting in the gills of four species of elasmobranchs, the banjo ray (Trygonorrhina fasciata), southern eagle ray (Myliobatis australis), the gummy shark (Mustelus antarcticus) and the Australian angel shark (Squatina australis) using heterologous antibodies. Na⁺/H⁺ exchanger 2-like immunoreactivity was observed in the gills of the banjo ray, eagle ray and angel shark. In the banjo and eagle rays, this Na⁺/H⁺ exchanger-like immunoreactivity co-localised with immunoreactivity to Na⁺/K⁺-ATPase, a marker for the mitochondrial-rich cells of fishes. Na⁺/H⁺ exchanger 3-like immunoreactivity was only observed in the gills of the angel and gummy sharks, some Na⁺/H⁺ exchanger 3-like cells also showed Na⁺/K⁺-ATPase immunoreactivity. However, immunoblotting of banjo and eagle ray gill membranes demonstrated Na⁺/H⁺ exchanger 3-like immunoreactivity, which was not consistent with the immunohistochemical results. These data demonstrate the presence of epithelial Na⁺/H⁺ exchangers 2 and 3 in the gills of elasmobranchs and a link with acid/base regulation is suggested.

Monitoring a commercial fermentation with proton nuclear magnetic resonance spectroscopy with the aid of chemometrics

Proton nuclear magnetic resonance spectroscopy (NMR) has shown the potential for being a valuable tool in monitoring a commercial fermentation. In this preliminary study, a suite of organic analytes including ethanol, fructose, glucose, methanol, glycerol, malic acid, tartaric acid, succinic acid, acetic acid and lactic acid were simultaneously determined during the fermentation. Data collection and analysis using chemometric algorithms aided the understanding of key processes including the effects of seeding a wine with bacteria for malo-lactic fermentation.

Effect of relaxation on pressure sensitivity index in a Zr-based metallic glass

Shear-banding features of as-cast and annealed Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 bulk metallic glass were investigated through Rockwell indentation tests. Isothermal annealing of the as-cast samples was conducted at temperatures below its glass transition temperature, Tg. The exothermal enthalpy during continuous heating below Tg decreases with increasing annealing temperature, indicating the gradual reduction of free-volume upon annealing. The observation on the morphology of shear-banding pattern around the indents implies a reduced shear bands activity in the annealed samples. The included angles (2θ) between two families of shear bands emanating from the edge of Rockwell indent decrease from 88° for the as-cast sample to 79° for the sample annealed at 633 K for 1 h, indicating a pressure sensitive plasticity. By Mohr–Coulomb criterion, the pressure sensitive index can be obtained on the basis of the measured 2θ, which increases with increasing annealing temperature, indicating an increase of “atomistic friction” due to the reduction of the free volume upon annealing.

Influence of pH on hygral expansion, relaxation shrinkage and extensibility of wool fabric

The standard tests for relaxation shrinkage and hygral expansion of wool fabric take no account of pH. It is shown in this work that the pH of the solution in which wool fabric is relaxed as part of the procedure for measuring dimensional properties has a significant influence on the results. At around pH 4.8, which is close to the isoelectric point of wool, the hygral expansion reaches its greatest value and drops at both lower and higher pHs. A similar relationship between pH and extensibility of wool fabric was observed. Values of relaxation shrinkage were found to be dependant on pH. The reasons for the pH dependence of dimensional properties are discussed and these include changes in wool fiber swelling, yarn crimp and polymer relaxation phenomena with changes in pH.

Probing the flexibility of the DsbA oxidoreductase from Vibrio cholerae - a 15N -1H heteronuclear NMR relaxation analysis of oxidised and reduced forms of DsbA

We have determined the structure of the reduced form of the DsbA oxidoreductase from Vibrio cholerae. The reduced structure shows a high level of similarity to the crystal structure of the oxidized form and is typical of this class of enzyme containing a thioredoxin domain with an inserted α-helical domain. Proteolytic and thermal stability measurements show that the reduced form of DsbA is considerably more stable than the oxidized form. NMR relaxation data have been collected and analyzed using a model-free approach to probe the dynamics of the reduced and oxidized states of DsbA. Akaike's information criteria have been applied both in the selection of the model-free models and the diffusion tensors that describe the global motions of each redox form. Analysis of the dynamics reveals that the oxidized protein shows increased disorder on the pico- to nanosecond and micro- to millisecond timescale. Many significant changes in dynamics are located either close to the active site or at the insertion points between the domains. In addition, analysis of the diffusion data shows there is a clear difference in the degree of interdomain movement between oxidized and reduced DsbA with the oxidized form being the more rigid. Principal components analysis has been employed to indicate possible concerted movements in the DsbA structure, which suggests that the modeled interdomain motions affect the catalytic cleft of the enzyme. Taken together, these data provide compelling evidence of a role for dynamics in the catalytic cycle of DsbA.

Effect of structure relaxation on the plastic deformation behaviour in a Zr-based BMG under indenter

Vickers and nano indentations were performed on a structurally relaxed Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in the relaxed BMG was investigated and compared to that in the as-cast alloy. Results indicate that the plastic deformation in the BMG with structure relaxation is accommodated by the semicircular (primary) and radial (secondary) as well as tertiary shear bands. Quantitatively, the shear band density in the relaxed alloy was much lower than that in the as-cast alloy. The annihilation of free volume caused by the annealing was responsible for the embrittlement of the sample with structure relaxation.

A 7Li and 19F NMR relaxation study of LiCF3SO3 in plasticised solid polyether electrolytes

⁷Li and ¹⁹F NMR relaxation time (T₁, T₂, T_1ρ) measurements have been used to probe the dynamics of LiCF₃SO₃ dissolved in an amorphous co-polymer poly(ethylene oxide-co-propylene oxide), and in particular the influence of the plasticising agents propylene carbonate and dimethyl formamide. The changes in relaxation behaviour of ¹⁹F and ⁷Li with increasing plasticiser concentration are very different, as is the effect of each plasticiser. These differences can be explained qualitatively in terms of the interaction between the plasticiser and the ions. Preliminary ⁷Li T_1ρ measurements reveal two components at low temperatures.

The effect of solvent uptake on the relaxation behaviour, morphology and mechanical properties of a poly(ether ether ketone)/poly(etherimide) blend

The effects of solvent uptake on the relaxation behaviour, morphology and mechanical properties of poly(ether ether ketone) (PEEK), poly(etherimide) (PEI) and a 50/50 PEEK/PEI blend have been investigated. Amorphous films were immersed in acetone at 25°C, 35°C and 45°C until equilibrium uptake was achieved. The films were then examined by wide angle X-ray scattering (WAXS), differential scanning calorimetry (d.s.c.), dynamic mechanical relaxation spectroscopy and mechanical testing. WAXS and d.s.c. revealed that the degree of solvent induced crystallinity in PEEK is constant with immersion temperature, whereas the degree of induced crystallinity in the 50/50 blend is strongly temperature dependent. The dynamic mechanical studies confirmed that a significant decrease in glass transition temperature results from the plasticizing effect of the solvent and that solvent and thermally crystallized samples have different relaxation characteristics. Mechanical property tests showed that the yield stress and tensile strength of the blend are dominated by PEEK and the degree of crystallinity, while the modulus is more sensitive to the extent of plasticization.

A study of hydrogen bonding in concentrated diol/water solutions by proton NMR correlations with glass formation

Solute/water interactions in a series of diol solutions have been investigated by ¹H NMR. Strong hydrogen bonding between water and alcohols that are more basic than water is thought to result in lower chemical shifts of water protons compared to the case of pure water. This is attributed to a greater degree of covalent character in the hydrogen bonding between water and the more basic diols. The inductive effect of the methyl group and longer chain alkyls is observed to increase basicity in ethylene glycol, propylene glycol, and 2,3-butanediol solutions. A correlation between the glass-forming ability of the diol solutions and the stronger hydrogen-bonding solutes (i.e., stronger bases) is developed, with 2,3-butanediol best promoting glass formation at the lowest concentrations.

13 C NMR spin–lattice relaxation times as a probeof local polymer dynamics in plasticized polyethers

¹³C NMR spin–lattice relaxation times T₁ are used to investigate the effect of low molecular weight diluents, including N,N-dimethylformamide, N-methylformamide, propylene carbonate, γ-butyrolactone, triglyme and tetraglyme, on the local polymer segmental motion in polyether–urethane networks. In all cases, an increase in the local mobility is deduced from the increasing T₁ measurements consistent with a decreasing glass transition temperature. The extent of plasticization, however, is dependent on the nature of the small molecules. Those molecules which can either form strong polymer-diluent interactions (for example through dipolar interactions) or are themselves rigid, give the least enhancement of polymer mobility and the greatest deviation from the Fox equation for T_g. In the presence of alkali metal salts, N,N-dimethylformamide and propylene carbonate are shown to have opposite effects on the local polymer motion, as seen from the T₁ measurements. In both cases, addition of the plasticizers increases the ¹³C T₁ relaxation times for the plasticizer. However, propylene carbonate decreases the polymer ¹³C T₁ whilst N,N-dimethylformamide results in the expected increase in polymer ¹³C T₁.

Dynamic mechanical thermal analysis studies of factors influencing relaxation in polyetherurethane based solid electrolytes

Dynamic mechanical thermal analysis (DMTA) has been used to study the effects of plasticizers on the mobility and homogeneity of a series of solid polymer electrolytes (SPEs). With reference to previously published results on similar systems containing LiClO₄ salts and tetraglyme as plasticizer, the effects of propylene carbonate (PC) on the glass transition temperature (T_g) of the SPE and on the distribution of relaxation times within the sample are discussed; at low plasticizer concentration PC has little effect on T_g as measured by DMTA in comparison with tetraglyme, and at higher plasticizer concentrations PC significantly broadens the mechanical relaxation behaviour indicating a greater degree of dynamical heterogeneity within the sample. A second low temperature relaxation is evident at lower PC contents indicating that some regions of this plasticized SPE are distinctly more mobile than others or perhaps, on this length scale, that some degree of phase separation is present. Activation energies for the mechanical relaxation were also determined as a function of PC concentration and are significantly greater than those determined from conductivity measurements.

Characterization of a proton conductor based on silicotungstic acid

It was found in this work that silicotungstic acid hydrate could be mixed with phosphoric acid (H₃PO₄, 85%) to make a viscous paste material with high conductivity (10⁻² S/cm at room temperature). The STA/H₃PO₄ paste samples were stable at 80°C in the atmosphere, and at 100°C under constant humidity over 10 days. The conductivity behavior of the paste samples has been investigated under various conditions, and it was found to be dependent on temperature, paste composition, and environment humidity.

A new class of proton-conducting ionic plastic crystals based on organic cations and dihydrogen phosphate

Choline dihydrogen phosphate ([N_1.1.1.2OH]DHP) and 1-butyl-3-methylimidazolium dihydrogen phosphate ([C₄mim]DHP) were synthesized as a new class of proton-conducting ionic plastic crystals. Both [N_1.1.1.2OH]DHP and [C₄mim]DHP showed solid–solid phase transition(s) and showed a final entropy of fusion lower than 20 J K⁻¹ mol⁻¹ which is consistent with Timmerman’s criterion for molecular plastic crystals. The ionic conductivity of [N_1.1.1.2OH]DHP was in the range of 10⁻⁶ S cm⁻¹–10⁻³ S cm⁻¹ in the plastic crystalline phase. On the other hand, the ionic conductivity of [C₄mim]DHP showed about 10⁻⁵ S cm⁻¹ in the plastic crystalline phase. [N_1.1.1.2OH]DHP showed one order of magnitude higher ionic conductivity than [C₄mim]DHP in the temperature range where the plastic phase is stable.