Photocatalytic decolorization of lanasol blue CE dye solution using a flat-plate reactor

This paper reports the effectiveness of the photocatalysis TiO₂ in degrading Lanasol Blue CE. A flat-plate reactor (FPR) with a reactor area of 0.37 m² and ultraviolet (UV) light source of six 36 W blacklight lamps was used in the study. Operating variables including dosage of the photocatalyst, flow rates through the FPR, UV intensity, and tilted angle of the reactor were investigated to degrade Lanasol Blue CE. Results showed that the photocatalytic process can efficiently remove the color in textile dyeing effluent. The degradation process was approximated using first-order kinetics. The photocatalytic apparent reaction rate increased with the increasing UV intensity received by the photocatalyst TiO₂ in slurry. The liquid flow rate and tilted angle influenced the film thickness. The apparent reaction rate constant was mainly determined by the liquid film thickness, UV intensity, and the dosage of the photocatalyst. The findings of this research can be utilized as preliminary input for potential solar photocatalytic applications on color removal from dye solutions.

Photocatalytic degradation of dyes in wastewater using TiO2/UV in a flat-plate reactor

The photocatalyst TiO₂ with UV irradiation was used to degrade dyes in textile effluent in a flat-plate photoreactor. A test system was built with the reactor area of 1 x 0.3m2, UV light of six 36W-blacklight. TiO₂ powder P25 with BET surface area 50±15m2/g, average primary particle size 21 nm, purity> 99.5% and content of 83.9% anatase and 16.1 % rutile was used as the photocatalyst. A number of dyes commonly present in dyeing wastewater were tested in this study. The different operating parameters, such as dosage of photocatalyst, the structure of the reactor, flow rates through the flat-plate reactor, UV radiation intensity and tilted angle of the reactor, were investigated. The results showed that the photocatalytic process could efficiently remove most of the colour contained in the dyeing wastewater. It was experimentally observed that first-order kinetics was adequate for characterising the process. The flow rate and the tilted angle had some influence on the film thickness of the fluid in the reactor and the empirical correlation between the film thickness of the fluid and these two parameters was developed. The photoreaction rate was mainly determined by the film thickness of the fluid on the reactor surface and the dosage of the photocatalyst. Optimum operating parameters of the system were found to be at the film thickness of about 1.4mm and a TiO₂ dosage of 1 gIL. The higher the UV intensity, the faster the reaction rate was. The results of these experiments showed that this method has the great potential for colour removal from wastewater at commercial scale.

To overcome the common difficulty of separating the used TiO₂ suspension after treatment precipitation followed with filtration was used in this study to determine the separation efficiencies. On the other hand, TiO₂ in a small pillar shape was also studied for photocatalytic degradation of textile dye effluent. The pillar pellet was made in Oegussa Company, Germany ranging from 2.5 to 5.3mm long and with a diameter of 3.7mm. It was almost pure TiO₂ (83.2% anatase and 16.8% rutile), with a S-content of <20 ppm and a CI content of the order of 0.1 wt. %. No further elements are present in contents above 0.05 wt.%. The TiO₂ pillars were placed on the flat-plate reactor that was divided by the rectangular slots and irradiated under UV light when the treated solution went through the reactor. Four dyes and their mixtures were tested. The results showed that the photocatalytic process under this configuration efficiently remove the colour from textile dyeing effluent, and pillar shape TiO₂ photocatalyst was not dissolved in water and very easy to be separated from solution, enabling it to be reused many times. The first-order kinetics was adequate for characterising the photocatalytic degradation process and the photocatalytic performance was comparable to TiO₂ powder. It is believed that the TiO₂ pellet would be a preferable form of photocatalyst in applications for textile effluent treatment process, and other wastewater treatment processes.

Solar photocatalytic oxidation (PCO) process with a flat-plate reactor

An experimental rig with a flat-plate solar reactor was built to study the effectiveness of degradation using the reactive methylene blue as sensitive objective. The factors that affect the degradation performance, such as dosages of photocatalyst (Ti0₂), initial concentration of reactive methylene blue, flow rate through the flat-plate reactor, solar UV radiation intensity and decolourising efficiency of the solution, have been investigated. The results showed that the solar PCO process with a Flat-plate Reactor could degrade the methylene blue and decolour in methylene blue solution efficiently.

Photocatalytic degradation of dye effluent by titanium dioxide pillar pellets in aqueous solution

Photocatalytic oxidation (PCO) process is an effective way to deal with organic pollutants in wastewater which could be difficult to be degraded by conventional biological treatment methods. Normally the TiO2 powder in nanometre size range was directly used as photocatalyst for dye degradation in wastewater. However the titanium dioxide powder was arduous to be recovered from the solution after treatment. In this application, a new form of TiO2 (i.e. pillar pellets ranging from 2.5 to 5.3 mm long and with a diameter of 3.7 mm) was used and investigated for photocatalytic degradation of textile dye effluent. A test system was built with a flat plate reactor (FPR) and UV light source (blacklight and solar simulator as light source respectively) for investigating the effectiveness of the new form of TiO2. It was found that the photocatalytic process under this configuration could efficiently remove colours from textile dyeing effluent. Comparing with the TiO2 powder, the pellet was very easy to recovered from the treated solution and can be reused in multiple times without the significant change on the photocatalytic property. The results also showed that to achieve the same photocatalytic performance, the FPR area by pellets was about 91% smaller than required by TiO2 powder. At least TiO2 pellet could be used as an alternative form of photocatalyst in applications for textile effluent treatment process, also other wastewater treatment processes.

A solar collector with the absorber divided by rectangular slots

A new solar absorber structure has been proposed and studied in this paper. The metal tubes running perpendicular to a set of parallel rectangular metal fins make the solar absorber with rectangular slots. Studies on the collector were theoretically carried out in the aspects of heat transfer, thermodynamics and . hydrodynamics. The calculating methods for calculating fin efficiency F and efficiency factors of the collector F' were obtained. The results showed that the new solar collector would have the higher efficiency and better performance at higher fluid temperature than that of the traditional flat-plate collectors. A collector prototype with the new structure was built and tested. The testing results agree with our theoretical results.

Propagation characteristics of lamb waves in stringer-stiffened panels

Stringer-stiffened plate-like structure is a typical engineering structure and its structural integrity is critical. A guided Lamb wave-based damage identification scheme and an online structural health monitoring (SHM) system with an integrated PZT-sensor network were developed. In the previous studies, the specimens were relatively simple. In this paper, the above mentioned method was extended to the stiffened plate-like structure—a flat plate reinforced by stringer. FE dynamic simulation was applied to investigate the Lamb wave propagation characteristics due to the existence of stringer with the consideration of its material and geometric configurations.

Solar energy use for energy savings in dairy processing plants

New Zealand is one of the world’s largest producers of dairy products and has a climate with high levels of solar radiation; however, the use of solar energy in the dairy processing industry has received limited attention. An examination of historical records found that the annual peak in New Zealand milk production and processing occurs at a time when solar radiation levels are increasing markedly. An F-Chart analysis was used to simulate the performance of large-area arrays of solar collectors and to determine their suitability for heating and cooling in a dairy processing environment. For the study four types of solar collectors were analysed: glazed flat plates, evacuated tubes, evacuated tubes with CPC reflectors and a building-integrated solar collector under development at the University of Waikato (UoW). It was found that of these echnologies, both flat plate and evacuated tubes with CPC reflectors could make useful heating and cooling contributions. Furthermore, the solar fraction was determined mainly by the collector area to storage volume ratio. Finally, it was found that the UoW building-integrated solar collector could make a significant contribution to energy use in dairies and may be an attractive future technology for the industry.

A family of simple and robust finite elements for linear and geometrically nonlinear analysis of laminated composite plates

A family of simple, displacement-based and shear-flexible triangular and quadrilateral flat plate/shell elements for linear and geometrically nonlinear analysis of thin to moderately thick laminate composite plates are introduced and summarized in this paper.

The developed elements are based on the first-order shear deformation theory (FSDT) and von-Karman’s large deflection theory, and total Lagrangian approach is employed to formulate the element for geometrically nonlinear analysis. The deflection and rotation functions of the element boundary are obtained from Timoshenko’s laminated composite beam functions, thus convergence can be ensured theoretically for very thin laminates and shear-locking problem is avoided naturally.

The flat triangular plate/shell element is of 3-node, 18-degree-of-freedom, and the plane displacement interpolation functions of the Allman’s triangular membrane element with drilling degrees of freedom are taken as the in-plane displacements of the element. The flat quadrilateral plate/shell element is of 4-node, 24-degree-of-freedom, and the linear displacement interpolation functions of a quadrilateral plane element with drilling degrees of freedom are taken as the in-plane displacements.

The developed elements are simple in formulation, free from shear-locking, and include conventional engineering degrees of freedom. Numerical examples demonstrate that the elements are convergent, not sensitive to mesh distortion, accurate and efficient for linear and geometric nonlinear analysis of thin to moderately thick laminates.

Seasonal coolth storage system for residential buildings in Australia

Night sky cooling is explored as an alternative to the conventional cooling technologies using fossil fuels. The night sky cooling method is based on the long wave radiation of unglazed collectors to the sky at night. An evaluation of the night sky cooling system is present for a residential building in three cities of Australia, namely Alice Springs, Darwin and Melbourne. The system comprises an unglazed flat plate solar collector integrated with borehole storage. It uses night sky radiation to reduce the temperature of the ground near to the boreholes. The system was simulated with TRNSYS, a transient simulation program. The simulation results for adequately sized systems show that night sky radiation is able to reduce the coolth storage borehole temperature and the proposed system is able to meet the cooling load of the residential building simulated in three locations. Borehole lengths of 270, 318 and 106 m are required for coolth storage with 90, 260 and 14 m2 collector area for heat rejection in Alice Springs, Darwin and Melbourne, respectively. At the 20th simulation year, the proposed system is able to achieve a system cooling coefficient of performance of 2.2 in Alice Springs, and 2.8 in Darwin and Melbourne.

Towards simulation of flapping wings using immersed boundary method

In this work the immersed boundary method is applied to simulate incompressible turbulent flows around stationary and moving objects. The goal is to demonstrate that the immersed boundary technique along with a large eddy simulation approach is capable of simulating the effect of the so-called leading edge vortex (LEV), which can be found in flapping wing aerodynamics. A Lagrangian method is used to approximatethe solutions in the freshly cleared cells that lay within solid objects at one time step and emerge into fluid domain at the next time step. Flow around a stationary cylinder at ReD D 20, 40, and 3900 (based oncylinder diameter D) is first studied to validate the immersed boundary solver based on the finite volume scheme using a staggered grid. Then, a harmonically oscillating cylinder at ReD D 10 000 is considered to test the solver after the Lagrangian method is implemented to interpolate the solution in the freshly cleared cells. Finally, this approach is used to study flows around a stationary flat-plate at several angles of attack and fast pitching flat-plate. The rapidly pitching plate creates a dynamic LEV that can be used to improve the efficiency of flapping wings of micro air vehicle and to determine the optimum flapping frequency.

Interaction between the coating characteristics of galvanneal steel and forming parameters during flat die drawing

Galvanneal steel is considered to be better for automotive applications than its counterpart, galvanized steel, mainly because of its superior coating and surface properties. Galvanneal steel is produced by hot dipping sheet steel in a bath of molten zinc with small, controlled, levels of aluminium, followed by annealing which creates a Fe-Zn intermetallic layer. This intermetallic layer of the coating improves spot weldability and improves subsequent paint appearance. However, if the microstructure of the coating is not properly controlled and forming parameters are not properly selected, wear of the coating could occur during stamping. Frictional sliding of the sheet between the tool surfaces results in considerable amount of coating loss. An Interstitial Free steel with a Galvanneal coating of nominally 60g/m2 was used for the laboratory experiments. Flat Face Friction (FFF) tests were performed with different forming conditions and lubricants to simulate the frictional sliding in stamping. Glow-Discharge Optical Emission Spectrometry (DG-OES) was used to measure the change in the coating thickness during sliding. Optical microscopy was considered for imaging the surfaces as well as an optical method to compare the changes in the coating thickness during the forming. The change to the Galvanneal coating thickness was found to be a function of forming parameters.

Some aspects of numerical simulation for lamb wave propogation in composite laminates

Some aspects of numerical simulation of Lamb wave propagation in composite laminates using the finite element models with explicit dynamic analysis are addressed in this study. To correctly and efficiently describe the guided-wave excited/received by piezoelectric actuators/sensors, effective models of surface-bounded flat PZT disks based on effective force, moment and displacement are developed. Different finite element models for Lamb wave excitation, collection and propagation in isotropic plate and quasi-isotropic laminated composite are evaluated using continuum elements (3-D solid element) and structural elements (3-D shell element), to elaborate the validity and versatility of the proposed actuator/sensor models.

A comparative study of microstructures and mechanical properties obtained by bar and plate rolling

Microstructures and mechanical properties of a low carbon steel were studied after plate rolling and bar rolling. Plate rolling is characterized as a monotonic compressive loading, while bar rolling is characterized as a cross-compressive loading. A four-pass plate rolling and bar rolling experiment was designed so that the material experiences the same amount of strain at each pass during rolling. The rolling experiment was performed at moderately high temperatures (450, 550 and 650 °C). The microstructures and mechanical properties of the low carbon steel acquired from the two types of rolling experiments were compared. The results revealed that differences of loading path attributed by monotonic loading (plate rolling) and cross loading (bar rolling) significantly influenced the microstructures and mechanical properties such as yield stress, ultimate tensile stress, strain hardening exponent and elongation of the low carbon steel.

From Flysch to Molasse - sedimentary and tectonic evolution of late Caledonian - early Hercynian Foreland Basin in North Qilian Mountains

The Late Caledonian to Early Hercynian North Qilian orogenic belt in northwestern China is an elongate tectonic unit situated between the North China plate in the north and the Qaidam plate in the south. North Qilian started in the latest Proterozoic to Cambrian as a rift basin on the southern margin of North China, and evolved later to an archipelagic ocean and active continental margin during the Ordovician and a foreland basin from Silurian to the Early and Middle Devonian. The Early Silurian flysch and submarine alluvial fan, the Middle to Late Silurian shallow marine to tidal flat deposits and the Early and Middle Devonian terrestrial molasse are developed along the corridor Nanshan. The shallowing-upward succession from subabyssal flysch, shallow marine, tidal flat to terrestrial molasse and its gradually narrowed regional distribution demonstrate that the foreland basin experienced the transition from flysch stage to molasse stage during the Silurian and Devonian time.