Porous carbon nanotube/polyvinylidene fluoride composite material: Superhydrophobicity/superoleophilicity and tunability of electrical conductivity

Porous carbon nanotube/polyvinylidene fluoride (CNT/PVDF) composite material can be fabricated via formation and freeze-drying of a gel. The field emission scanning electron microscopy, nitrogen adsorption-desorption and pore size distribution analysis reveal that the introduction of a small amount of carbon nanotubes (CNTs) can effectively increase the surface roughness and porosity of polyvinylidene fluoride (PVDF). Contact angle measurements of water and oil indicate that the as-obtained composite material is superhydrophobic and superoleophilic. Further experiments demonstrate that these composite material can be efficiently used to separate/absorb the insoluble oil from oil polluted water as membrane/absorbent. Most importantly, the electrical conductivity of such porous CNT/PVDF composite material can be tuned by adjusting the mass ratio of CNT to PVDF without obviously changing the superhydrophobicity or superoleophilicity. The unique properties of the porous CNT/PVDF composite material make it a promising candidate for oil-polluted water treatment as well as water-repellent catalyst-supporting electrode material.

Effect of synthesis parameters on the electrical conductivity of polypyrrole-coated poly(ethylene terephthalate) fabrics

The effects of pyrrole, anthraquinone-2-sulphonic acid (AQSA) and iron(III) chloride (FeCl3) concentrations, reaction time and temperature on the electrical conductivity of polypyrrole (PPy) - coated poly(ethylene terephthalate) (PET) fabrics were investigated. With an increase in both the AQSA and FeCl3 concentrations, resistivity decreased to a point beyond which higher concentrations led to increased surface resistivity. Erosion of the polymer coating, in dynamic synthesis from continual abrasion, manifested as an exponential increase in the resistance of the coated textile substrate. This was not encountered in static synthesis conditions. Temperature affected the degree of surface and bulk polymerisation. The effect of polymerisation temperature on conductivity was negligible. Conductive polymer coating on textiles through chemical polymerisation enabled a smooth coherent film to encase individual fibres, which did not affect the tactile properties of the host substrate. The optimum FeCl3/pyrrole and AQSA FeCl3/pyrrole molar ratios were found to be 2.22 and 0.40 respectively.

Decay of electrical conductivity in p-toluene sulfonate doped polypyrrole films

Long term performance of conductivity of p-toluene sulfonic acid (pTSA) doped electrochemically synthesized polypyrrole (PPy) films was estimated from accelerated aging studies between 80 °C and 120 °C. Conductivity decay experiments indicated that overall aging behavior of PPy films deviated from first order kinetics at prolonged aging times at elevated temperatures. However, an approximate value for the activation energy of the conductivity decay of PPy was calculated as E=47.4 kJ/mol, enabling an estimate of a rate constant of k=8.35×10⁻⁶/min at 20 °C. The rate of decrease of conductivity was not only temperature dependent but also influenced by the dopant concentration. A concentration of 0.005 M pTSA in the electrolyte resulted in a conductive film and when this film was exposed to 120 °C for a period of 40 h, the conductivity decayed to about 1/20 of its original value. The concentration of pTSA was increased to 0.05 mol/l and when the resulting film was aged in the same way, it showed a decrease in the conductivity to about 1/3 of its original value. Both microwave transmission and dc conductivity data revealed that highly doped films were considerably more electrically stable than lightly doped films. The dopant had a preserving effect on the electrical properties of PPy.

Spatial modeling of electrical conductivity with neural network

Many policy decisions for agricultural management in the coastal region closely depend on the extent of intrusion of sea water. In this study, Artificial Neural Network (ANN) is used to model the spatial variation of Electrical Conductivity to determine the extent of sea water intrusion in the coastal area of Brisbane, Australia. Quarterly EC data obtained from the observation (monitoring) wells located along the coast is used for training ANN architecture. The study demonstrates that ANN is able to model the spatial variation of EC with very good accuracy (even with very less training records) when some spatial information is used as one of the inputs in the network training. The results considerable improvement when compared with the network trained without the distance information.

Body fat estimated from anthropometric and electrical impedance measurements

Estimates of body fat based on anthropometric measurements were compared in two groups of females, one from the local community and the other from the 1984 Australian Olympic Team. Estimates of body fat based on electrical impedance measurements were also made for the community group. For estimates of total body fat based on skinfold measurements, a significant difference of approximately 1 kg fat/m2 was observed between athletes and non-athletes. In the group of non-athletes estimates of fat based on skinfold measurements were significantly higher than those based on body mass index, with estimates from electrical impedance falling between. Electrical impedance measurements may provide a means of estimating body fat which takes into account differences in fat distribution and in the ratio of fat to fat-free tissue and may thus overcome the problems associated with estimates based on measurements of subcutaneous fat (skinfolds) or body size which do not allow for these differences.

Morphology evolution during annealing and electrical conductivity of titania nanotube films

Titania nanotube films were produced by anodization of titanium foil. The titania nanotube films were annealed at different temperatures. Morphology evolution, phase transformation and electrical conductivity of the titania nanotubes were studied. Results showed that the nanotube walls became rough, porous and even collapsed after annealed at 400, 500 and 600°C respectively. Titania anatase phase formed after annealed at 400°C; the amount of anatase phase increased as the annealing temperature increased. The conductivity of the nanotube film annealed at 400°C was improved greatly compared with the conductivity of the as-anodized nanotube film. However, the conductivity of the nanotube films annealed at higher temperatures decreased. The effect of the morphology on the electronic conductivity of the titania nanotube films was discussed.

Influence of ionic liquids on the electrical conductivity and morphology of PEDOT:PSS films

Small-molecule nonvolatile additives based on ionic liquids (IL) as electrical conductivity enhancer in Poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) was studied. Ionic liquids were investigated in the synthesis of self-assembled, highly organized hybrid nanostructures due to their ability as supramolecular solvents. Different percentage of five ionic liquids, such as 1-butyl-3-methylimidazolium tetrafluoroborate (bmim) F 4 and 1-butyl-3-methylimidazolium bromide (bmim)Br were added to a PEDOT:PSScommercial dispersion. Films of pure PEDOT:PSS showed an average conductivity of 14 S cm-1, which corresponded to the value range given by the supplier. AFM images showed that IL induced the formation of a three-dimensional conducting network with smaller PEDOT domains. The ionic character of the films was significantly increased because of the presence of ionic liquids, which can be used effectively in optoelectronic devices.

One-Step Wet-Spinning Process of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate) Fibers and the Origin of Higher Electrical Conductivity

A simplified wet-spinning process for the production of continuous poly (3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) fibers is reported. Conductivity enhancement of PEDOT:PSS fibers up to 223 S cm−1 has been demonstrated when these fibers are exposed to ethylene glycol as a post-synthesis processing step. In a new spinning approach it is shown that by employing a spinning formulation consisting of an aqueous blend of PEDOT:PSS and poly(ethlylene glycol), the need for post-spinning treatment with ethylene glycol is eliminated. With this approach, 30-fold conductivity enhancements from 9 to 264 S cm−1 are achieved with respect to an untreated fiber. This one-step approach also demonstrates a significant enhancement in the redox properties of the fibers. These improvements are attributed to an improved molecular ordering of the PEDOT chains in the direction of the fiber axis and the consequential enrichment of linear (or expanded-coil like) conformation to preference bipolaronic electronic structures as evidenced by Raman spectroscopy, solid-state electron spin resonance (ESR) and in situ electrochemical ESR studies.

Strain-responsive polyurethane/PEDOT:PSS elastomeric composite fibers with high electrical conductivity

It is a challenge to retain the high stretchability of an elastomer when used in polymer composites. Likewise, the high conductivity of organic conductors is typically compromised when used as filler in composite systems. Here, it is possible to achieve elastomeric fiber composites with high electrical conductivity at relatively low loading of the conductor and, more importantly, to attain mechanical properties that are useful in strain-sensing applications. The preparation of homogenous composite formulations from polyurethane (PU) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) that are also processable by fiber wet-spinning techniques are systematically evaluated. With increasing PEDOT:PSS loading in the fiber composites, the Young's modulus increases exponentially and the yield stress increases linearly. A model describing the effects of the reversible and irreversible deformations as a result of the re-arrangement of PEDOT:PSS filler networks within PU and how this relates to the electromechanical properties of the fibers during the tensile and cyclic stretching is presented. Conducting elastomeric fibers based on a composite of polyurethane (PU) and PEDOT:PSS, produced by a wet-spinning method, have high electrical conductivity and stretchability. These fibers can sense large strains by changes in resistance. The PU/PEDOT:PSS fiber is optimized to achieve the best strain sensing. PU/PEDOT:PSS fibers can be produced on a large scale and integrated into conventional textiles by weaving or knitting. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Improving the toughness and electrical conductivity of epoxy nanocomposites by using aligned carbon nanofibres

There is an increasing demand for high performance composites with enhanced mechanical and electrical properties. Carbon nanofibres offer a promising solution but their effectiveness has been limited by difficulty in achieving directional alignment. Here we report the use of an alternating current (AC) electric field to align carbon nanofibres in an epoxy. During the cure process of an epoxy resin, carbon nanofibres (CNFs) are observed to rotate and align with the applied electric field, forming a chain-like structure. The fracture energies of the resultant epoxy nanocomposites containing different concentrations of CNFs (up to 1.6wt%) are measured using double cantilever beam specimens. The results show that the addition of 1.6wt% of aligned CNFs increases the electrical conductivity of such nanocomposites by about seven orders of magnitudes to 10^-2S/m and increases the fracture energy, G<inf>Ic</inf>, by about 1600% from 134 to 2345J/m². A modelling technique is presented to quantify this major increase in the fracture energy with aligned CNFs. The results of this research open up new opportunities to create multi-scale composites with greatly enhanced multifunctional properties.

Electrical conductivity of single walled and multiwalled carbon nanotube containing wool fibers

The main purpose of this study was producing conductive wool fabric applying carbon nanotubes. Raw and oxidized wool samples were treated with carbon nanotubes in the impregnating bath in the presence of citric acid as a crosslinking agent and sodium hypophosphite as a catalyst while sonicating them in the ultrasonic bath. Electrical resistance, washing durability, and color variation of treated samples were assessed. Through SEM images, the surface morphology of treated samples was studied confirming the surface coating through carbon nanotubes. According to the results, the electrical resistance of treated wool with carbon nanotubes reduced substantially. However, the single-walled carbon nanotubes are more useful to increase the conductivity. In addition, the wool color changed into gray after the treatment.

Microstructure and electrical conductivity of aluminium/steel bimetallic rods processed by severe plastic deformation

Equal-channel angular pressing (ECAP) was used to fabricate Al/steel bimetallic rod for potential application in overhead transmission conductors. Bimetallic rods consisted of an austenitic stainless steel 316L core and an Al alloy 6201 cladding layer. By means of ECAP processing at 175°C, increase of mechanical strength without loss of electrical conductivity was achieved for one particular rod geometry out of three geometries tested. X-ray diffraction and transmission electron microscopy were employed to analyse how the microstructure was influenced by the number of processing passes and the bimetallic rod geometry. The co-deformation mechanism of the bimetallic rod under ECAP and accelerated dynamic ageing of Al alloy 6201 were discussed based on the microstructure characterisation results.

Effect of the degree of crystallinity on the electrochemical behavior of Mg65Cu25Y10 and Mg70Zn25Ca5 bulk metallic glasses

The effect of varying the percent crystallinity on the electrochemical behavior of Mg65Cu25Y10 and Mg70Zn25Ca5 bulk metallic glasses was studied. The alloys were heat-treated to achieve desired microstructures ranging from fully amorphous to fully crystalline, providing a systematic basis for subsequent testing. Potentiodynamic experiments in 0.01 M sodium chloride (NaCl) were used, whereby both the amorphous and partially crystallized samples were observed to have more noble corrosion potentials and lower anodic kinetics. However, this was accompanied by more rapid cathodic kinetics relative to their fully crystalline counterparts, meaning that corrosion rates were not significantly lower in the amorphous state. To describe the electrochemical response as a function of the degree of crystallinity, differential scanning calorimetry (DSC), scanning electron microscopy, x-ray diffraction (XRD), and electrical conductivity measurements were undertaken, where it was found that crystallinity alone is not necessarily the controlling factor and microchemistry that evolves upon devitrification, plays a key role in the electrochemical response of these materials.

Conductive fabrics for heating applications

By coating textiles with electrically conductive organic polymers, we are able to produce functional, intelligent fabrics. These fabrics can be utilised in applications such as gas sensors, actuators, electromagnetic shielding, radar absorption, selected frequency filtering in indoor wireless applications, and heating applications where vital parts of the body can be heated without embedding any wiring through the fabric.

Heat generation in fabrics coated with the conductive polymer polypyrrole was investigated. The fabrics were coated by chemical synthesis methods by oxidizing the pyrrole monomer in the presence of the fabric substrate. Ferric chloride was selected as the oxidizing agent and anthraquinone-2-sulfonic acid (AQSA) sodium salt monohydrate as the dopant.

Conductive fabrics were characterized by resistivity measurements, scanning electron microscopy, thermal imaging, current transmission over a period of time and calculations of power density per unit area. Effects of reaction conditions on the electrical properties and heat generated are presented. Polypyrrole coated fabrics were stable and possessed high electrical conductivity. Resistivity values ranged from 100-500 ohms/square depending on the reaction parameters. When subjected to a constant voltage of 24V, the polypyrrole coated polyester-Lycra® fabric doped with AQSA reached a maximum temperature of 42°C and a power density per unit area of 430 W/m² was achieved.

Thermal conductivity studies on wool fabrics with conductive coatings

Methods of improving the thermal conductivity of wool fabrics have been investigated. Thermal conductivity measurement techniques, influence of synthesis parameters on the thermal conductivity of polypyrrole (PPy)-coated wool fabrics, and the relationship between electrical conductivity and thermal conductivity of PPy-coated wool fabrics are presented. An improvement in thermal conductivity was observed when fabrics were coated with the PPy. The thermal conductivity increased with the increase of pyrrole concentration and synthesis time. Anthraquinone-2-sulfonic acid and ferric chloride showed an optimal concentration for their influence on the thermal conductivity of the coated fabric. The improvement of thermal conductivity of wool fabrics is also investigated by Physical Vapor Deposition technique.