Design of a distributed power system stabiliser

A new design method for a distributed power system stabiliser for interconnected power systems is introduced in this paper. The stabiliser is of a low order, dynamic and robust. To generate the required local control signals, each local stabiliser requires information about either the rotor speed or the load angle of the other subsystems. A simple MATLAB based design algorithm is given and used on a three-machine unstable power system. The resulting stabiliser is simulated and sample results are presented.

Power demand and energy usage of container crane - comparison between AC and DC drives

The electrical data of two quay cranes, one has a DC drive system and the other has an AC drive system, in actual working conditions at a container terminal are measured and presented in this paper. Peak demand, energy usage, power factor and power quality are examined and compared.

Power analysis and simulation of a vehicle under combined loads

This paper presents an analytical model of fuel consumption (AMFC) to coordinate the driving power and manage the overall fuel consumption for an internal combustion engine vehicle. The model calculates the different loads applied on the vehicle including road-slope, road-friction, wind-drag, accessories, and mechanical losses. Also, it solves the combustion equation of the engine under different working conditions including various fuel compositions, excess airs and air inlet temperatures. Then it determines the contribution of each load to signify the energy distribution and power flows of the vehicle. Unlike the conventional models in which the vehicle speed needs to be given as an input, the developed model can predict the vehicle speed and acceleration under different working conditions by allowing the speed to vary within a predefined range only. Furthermore, the model indicates the ways to minimises the vehicles' fuel consumption under various driving conditions. The results show that the model has the potential to assist in the vehicle energy management.

Utilising solar energy within conventional coal fired power stations

Although the thermodynamic advantages of using solar energy to replace the bled off steam in the regeneration system of Rankine cycle coal fired power stations has been proven theoretically, the practical techno/economic feasibility of the concept has yet to be confirmed relative to real power station applications. To investigate this concept further, computer modelling software “THERMSOLV” was specifically developed for this project at Deakin University, together with the support of the Victorian power industry and Australian Research Council (ARC). This newly developed software simulates the steam cycle to assess the techno/economic merit of the solar aided concept for various power station structures, locations and local electricity market conditions. Two case studies, one in Victoria Australia and one in Yunnan Province, China, have been carried out with the software. Chapter one of this thesis defines the aims and scope of this study. Chapter two details the literature search in the related areas for this study. The thermodynamic concept of solar aid power generation technology has been described in chapter three. In addition, thermodynamic analysis i.e. exergy/availability has been described in this chapter. The “Thermosolv” software developed in this study is detailed in chapter four with its structure, functions and operation manual included. In chapter five the outcomes of two case studies using the “Thermosolv” software are presented, with discussions and conclusions about the study in chapters 6 and 7 respectfully. The relevant recommendations are then made in chapter eight.

Hybrid cooling system for water conservation in conventional power stations

This thesis proposes the concept of a hybrid cooling system to minimise water consumption in thermal power stations. It identifies that a significant amount of water can be potentially saved by the proposed system. Additional energy input requirements were less than previous approaches considered.

Too close for comfort : a fishway exit and a hydro-power station inlet

A major environmental issue for hydro-electric power generation is passage of fish through turbines, or entrainment onto trash racks. At Yarrawonga Weir, on the upper Murray River in south-eastern Australia, the positioning of a fish lock resulted in the potential for upstream migrating fish to be swept back into the adjacent power station by cross flows. In 2004, a 4.5-m long steel extension flume was attached to the exit to alleviate this problem. To determine the fate of native fish after exiting the extension flume, 72 individuals (305–1015 mm long) were implanted with radio-transmitters and released into the fish lock exit channel. In 2004 (power station inflows 10 300 ML day^–1), the majority of fish exited successfully (44 of 45) and only a single fish (2%) was entrained into the power station. In 2005 (power station inflows 12 000 ML day^–1), fish again exited successfully (26 of 27) but with a higher proportion entrained (5 of 27; 18%). This reduced success appeared to be related to strong transverse flows with high water velocities adjacent to the fish lock exit. The efficiency of fish passage at this site might be improved by altering water management strategies, integrating engineering and fish biology, and through field-testing of proposed solutions

Power plant cooling technologies : hybrid cooling systems can save water

In addition to water saving, the hybrid cooling concept presented in this book also has the potential to improve energy efficiency and possibly reduce CO2 emission by recovering and upgrading the 'waste' energy from the cooling water stream.Yilmaz and Kouzani are at Deakin Uni, Hessami is at Monash Uni, Hu is at Uni of Adelaide.

Modelling and power quality analysis of a grid-connected solar PV system

Increased concern about global warming coupled with the escalating demand of energy has driven the conventional power system to be more reliable one by integrating Renewable Energies (RE) in to grid. Over the recent years, integration of solar PV forming a gridconnected PV is considered as one of the most promisingtechnologies to the developed countries like Australia to meet the growing demand of energy. This rapid increase in grid connected photovoltaic (PV) systems has made the supply utilities concerned about the drastic effects that have to be considered on the distribution network in particular voltage fluctuations, harmonic distortions and the Power factor for sustainable power generation. However, irrespective of thefact that the utility grid can accommodate the variability of load or irregular solar irradiance, it is essential to study the impact of grid connected PV systems during higher penetration levels as the intermittent nature of solar PV adversely effects the grid characteristics in meeting the load demand. Hence, keeping this in track, this paper examines the grid-connected PV system considering a residential network of Geelong region (38◦.09' S and 144◦.21’ E) and explores the level of impacts considering summer load profile with a change in the level of integrations. Initially, a PV power system network model is developed in Matlab-Simulink environment and the simulations are carried out to explore the impacts of solar PV penetration at low voltage distribution network considering power quality (PQ) issues such as voltage fluctuations, harmonics distortion at different load conditions.

Synthesis of Al-doped Mg2Si1-xSnx compound using magnesium alloy for thermoelectric application

Abstract Mg2Si1-xSnx thermoelectric compounds were synthesized through a solid-state reaction at 700 °C between chips of Mg2Sn-Mg eutectic alloy and silicon fine powders. The Al dopants were introduced by employing AZ31 magnesium alloy that contains aluminum. The as-synthesized Mg2Si1-xSnx powders were consolidated by spark plasma sintering at 650-700 °C. X-ray diffraction and scanning electron microscopy revealed that the Mg2Si1-xSnx bulk materials were comprised of Si-rich and Sn-rich phases. Due to the complex microstructures, the electrical conductivities of Mg2Si1-xSnx are lower than Mg2Si. As a result, the average power factor of Al0.05Mg2Si0.73Sn0.27 is about 1.5 × 10^-3 W/mK² from room temperature to 850 K, being less than 2.5 × 10^-3 W/mK² for Al0.05Mg2Si. However, the thermal conductivity of Mg2Si1-xSnx was reduced significantly as compared to Al0.05Mg2Si, which enabled the ZT of Al0.05Mg2Si0.73Sn0.27 to be superior to Al0.05Mg2Si. Lastly, the electric power generation from one leg of Al0.05Mg2Si and Al0.05Mg2Si0.73Sn0.27 were evaluated on a newly developed instrument, with the peak output power of 15-20 mW at 300 °C hot-side temperature.

Nonlinear backstepping controller design for sharing active and reactive power in three-phase grid-connected photovoltaic systems

In this paper, a nonlinear backstepping controller is designed for three-phase grid-connected solar photovoltaic (PV) systems to share active and reactive power. A cascaded control structure is considered for the purpose of sharing appropriate amount of power. In this cascaded control structure, the dc-link voltage controller is designed for balancing the power flow within the system and the current controller is designed to shape the grid current into a pure sinusoidal waveform. In order to balance the power flow, it is always essential to maintain a constant voltage across the dc-link capacitor for which an incremental conductance (IC) method is used in this paper. This approach also ensures the operation of solar PV arrays at the maximum power point (MPP) under rapidly changing atmospheric conditions. The proposed current controller is designed to guarantee the current injection into the grid in such a way that the system operates at a power factor other than unity which is essential for sharing active and reactive power. The performance of the proposed backstepping approach is verified on a three-phase grid-connected PV system under different atmospheric conditions. Simulation results show the effectiveness of the proposed control scheme in terms of achieving desired control objectives.

Stabilisation of brown coal fly ash using geopolymers

This research explores geopolymer technology as a means of stabilising fly ash from power stations. By controlling the synthesis process, geopolymeric materials incorporating fly ash were synthesised. Successful stabilisation of strontium and barium was achieved, though attributed to side reactions. The geopolymer did not contribute significantly to stabilisation of fly ash.

A study on plug-in hybrid electic vehicles

Plug-in hybrid electric vehicle (PHEV), which is a hybrid vehicle whose batteries can be recharged by plugging into an electric power source, is creating many interests due to its significant potential to improve fuel efficiency and reduce pollution. PHEVs would be the next generation of vehicles that are expected to replace conventional hybrid electric vehicles. This paper presents a study on PHEV. It gives a review of different drivetrain architectures associated with PHEVs. In addition, different control strategies that could bring about realization of advantages of PHEV capabilities are discussed and compared.