Solid state NMR characterization of polyrrole : the nature of the dopant in PF6− doped films

³¹P and ¹⁹F solid state NMR have been used to study the nature of the PF₆− anion in polypyrrole films at various levels of oxidation. It appears that the symmetric PF₆− unit remains undistorted and unchanged throughout, suggesting that it is predominantly acting only as a counterion and not as a true ‘dopant’, since any distortion in the phosphorous environments would result at the very least in chemical shift anisotropy of the ³¹P nucleus. A second set of phosphorous and fluorine resonances, which are consistent with a difluoride phosphorous compound, appeared in the films. Upon electrochemical reduction of the polymer, the undistorted PF₆− anion leaves the film whereas the second phosphorous species remains. Re-oxidation of the polymer reverses the processes observed during reduction.

Decay of electrical conductivity in p-toluene sulfonate doped polypyrrole films

Long term performance of conductivity of p-toluene sulfonic acid (pTSA) doped electrochemically synthesized polypyrrole (PPy) films was estimated from accelerated aging studies between 80 °C and 120 °C. Conductivity decay experiments indicated that overall aging behavior of PPy films deviated from first order kinetics at prolonged aging times at elevated temperatures. However, an approximate value for the activation energy of the conductivity decay of PPy was calculated as E=47.4 kJ/mol, enabling an estimate of a rate constant of k=8.35×10⁻⁶/min at 20 °C. The rate of decrease of conductivity was not only temperature dependent but also influenced by the dopant concentration. A concentration of 0.005 M pTSA in the electrolyte resulted in a conductive film and when this film was exposed to 120 °C for a period of 40 h, the conductivity decayed to about 1/20 of its original value. The concentration of pTSA was increased to 0.05 mol/l and when the resulting film was aged in the same way, it showed a decrease in the conductivity to about 1/3 of its original value. Both microwave transmission and dc conductivity data revealed that highly doped films were considerably more electrically stable than lightly doped films. The dopant had a preserving effect on the electrical properties of PPy.

Aging studies on conducting polypyrrole

Change of tensile properties, electrical conductivity and microwave shielding of electrochemically synthesized polypyrrole films with time are presented. Highly doped films had good electrical stability, retaining high microwave reflectivity throughout the aging period. Lightly doped films were less stable and partially reflective and absorptive of microwaves. FT-IR spectral observations revealed a progressive increase in intensity of an unsaturated conjugated carbonyl peak, which was not observed in the highly doped films, suggesting that the concentration of the dopant had an influence on the mechanism of degradation of conductivity.

Electromagnetic interference shielding and radiation absorption in thin polypyrrole films

Results of permittivity measurements, electromagnetic interference shielding effectiveness, and heat generation due to microwave absorption in conducting polymer coated textiles are reported and discussed. The intrinsically conducting polymer, polypyrrole, doped with anthraquinone-2-sulfonic acid (AQSA) or para-toluene-2-sulfonic acid (pTSA) was applied on textile substrates and the resulting materials were investigated in the frequency range 1–18 GHz. The 0.54 mm thick conducting textile/polypyrrole composites absorbed up to 49.5% of the incident 30–35 W microwave radiation. A thermography station was used to monitor the temperature of these composites during the irradiation process, where absorption was confirmed via visible heat losses. Samples with lower conductivity showed larger temperature increases caused by microwave absorption compared to samples with higher conductivity. A sample with an average sheet resistivity of 150 Ω/sq. showed a maximum temperature increase of 5.27 °C, whilst a sample with a lower resistivity (105 Ω/sq.) rose by 3.85 °C.

The microstructure and properties of energetically deposited carbon nitride films

The intrinsic stress, film density and nitrogen content of carbon nitride (CNx) films deposited from a filtered cathodic vacuum arc were determined as a function of substrate bias, substrate temperature and nitrogen process pressure. Contour plots of the measurements show the deposition conditions required to produce the main structural forms of CNx including N-doped tetrahedral amorphous carbon (ta-C:N) and a variety of nitrogen containing graphitic carbons. The film with maximum nitrogen content (~ 30%) was deposited at room temperature with 1.0 mTorr N2 pressure and using an intermediate bias of - 400 V. Higher nitrogen pressure, higher bias and/or higher temperature promoted layering with substitutional nitrogen bonded into graphite-like sheets. As the deposition temperature exceeded 500 °C, the nitrogen content diminished regardless of nitrogen pressure, showing the meta-stability of the carbon-nitrogen bonding in the films. Hardness and ductility measurements revealed a diverse range of mechanical properties in the films, varying from hard ta-C:N (~ 50 GPa) to softer and highly ductile CN x which contained tangled graphite-like sheets. Through-film current-voltage characteristics showed that the conductance of the carbon nitride films increased with nitrogen content and substrate bias, consistent with the transition to more graphite-like films. © 2014 Elsevier B.V.

Facile preparation and thermoelectric properties of Bi₂Te₃ based alloy nanosheet/PEDOT:PSS composite films

Bi2Te3 based alloy nanosheet (NS)/poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) composite films were prepared separately by spin coating and drop casting techniques. The drop cast composite film containing 4.10 wt % Bi2Te3 based alloy NSs showed electrical conductivity as high as 1295.21 S/cm, which is higher than that (753.8 S/cm) of a dimethyl sulfoxide doped PEDOT:PSS film prepared under the same condition and that (850-1250 S/cm) of the Bi2Te3 based alloy bulk material. The composite film also showed a very high power factor value, ∼32.26 μWm(-1) K(-2). With the content of Bi2Te3 based alloy NSs increasing from 0 to 4.10 wt %, the electrical conductivity and Seebeck coefficient of the composite films increase simultaneously.

Raman microscopic analysis of internal stress in boron-doped diamond

Analysis of the induced stress on undoped and boron-doped diamond (BDD) thin films by confocal Raman microscopy is performed in this study to investigate its correlation with sample chemical composition and the substrate used during fabrication. Knowledge of this nature is very important to the issue of long-term stability of BDD coated neurosurgical electrodes that will be used in fast-scan cyclic voltammetry, as potential occurrence of film delaminations and dislocations during their surgical implantation can have unwanted consequences for the reliability of BDD-based biosensing electrodes. To achieve a more uniform deposition of the films on cylindrically-shaped tungsten rods, substrate rotation was employed in a custom-built chemical vapor deposition reactor. In addition to visibly preferential boron incorporation into the diamond lattice and columnar growth, the results also reveal a direct correlation between regions of pure diamond and enhanced stress. Definite stress release throughout entire film thicknesses was found in the OPEN ACCESS current Raman mapping images for higher amounts of boron addition. There is also a possible contribution to the high values of compressive stress from sp2 type carbon impurities, besides that of the expected lattice mismatch between film and substrate.

ZnO flower/PEDOT:PSS thermoelectric composite films

ZnO flower/poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) composite films were prepared by spin-coating dimethyl sulfoxide doped PEDOT:PSS on the ZnO flowers grown on glass substrate. The thermoelectric properties of the ZnO flower/PEDOT:PSS composite films were measured at room temperature. As the number of spin coated PEDOT:PSS layer increased, the electrical conductivity of the ZnO flower/PEDOT:PSS composite films increases dramatically from 1-layer (177.3 S/m) to 4-layer (910.4 S/m), however, all the composite films have almost the same Seebeck coefficient (~20–22 μV/K). A maximum power factor of ~0.4 μWm−1 K−2 at room temperature was obtained from the composite film with 4-layer PEDOT:PSS.