On the components of the dielectric constants of ionic liquids : ionic polarization?

According to dielectric spectroscopy measurements, ionic liquids (ILs) have rather modest dielectric constants that reflect contributions from distortion and electronic polarization caused by the molecular polarizability as well as the orientation polarization caused by the permanent dipole moment of the ions. To understand the relative importance of these various contributions, the electronic polarizabilities of 27 routinely used ionic liquid ions of different symmetry and size were calculated using ab initio-based methods such as HF and MP2. Using the Clausius–Mossotti equation, these polarizabilities were then used to obtain the electronic polarization contribution (ε_op) to the dielectric constants of six ionic liquids, [C₂mim][BF₄], [C₂mpyr][N(CN)₂], [C₂mim][CF₃SO₃], [EtNH₃][NO₃], [C₂mim][NTf₂] and [C₂mim][EtSO₄]. Theoretical ε_op values were compared to experimental refractive indices of these ionic liquids as well as to those of traditional molecular solvents such as water, tetrahydrofuran (THF), dimethylsulfoxide (DMSO) and formamide. The dipole moments of the ions were also calculated, and from these it is shown that the molecular reorientation component of the dielectric constants of the ionic liquids consisting of ions with small or negligible dipole moments is quite small. Thus it is concluded that a contribution from a form of “ionic polarization” must be present.

Triflate ion association in plasticized polymer electrolytes

Ion association in plasticised solid polymer electrolytes (SPEs) has been monitored using FT-IR spectroscopy. The SPEs were prepared from a random co-polymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethane sulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethylether (tetraglyme, ε˜5) and N,N'-dimethyl formamide (DMF, ε = 36.7) were chosen as model plasticisers. Decreased ion association resulted from plasticization with DMF, indicating that the addition of a higher dielectric constant solvent increases the fraction of dissociated ions in the SPE. The incorporation of tetraglyme into these SPEs results in increased ion association, despite the similar dielectric constants of the plasticiser and polymer host. The effects of salt concentration (0.05–1.25 mol dm^{− 3} solvent) upon ion association in SPEs was also investigated. There appears to be a minimum in the number of “free” ions at a LiTf concentration of 0.2 mol dm^{− 3} solvent followed by a maximum at approximately 0.4 mol dm^{− 3} solvent, consistent with the molar conductivity behaviour previously observed in these electrolytes.

Molecular dynamics study of response of liquid N,N-dimethylformamide to externally applied electric field using a polarizable force field

The behavior of Liquid N,N-dimethylformamide subjected to a wide range of externally applied electric fields (from 0.001 V/nm to 1 V/nm) has been investigated through molecular dynamics simulation. To approach the objective the AMOEBA polarizable force field was extended to include the interaction of the external electric field with atomic partial charges and the contribution to the atomic polarization. The simulation results were evaluated with quantum mechanical calculations. The results from the present force field for the liquid at normal conditions were compared with the experimental and molecular dynamics results with non-polarizable and other polarizable force fields. The uniform external electric fields of higher than 0.01 V/nm have a significant effect on the structure of the liquid, which exhibits a variation in numerous properties, including molecular polarization, local cluster structure, rotation, alignment, energetics, and bulk thermodynamic and structural properties.

A facile method to enhance ferroelectric properties in PVDF nanocomposites

Poly(vinylidene fluoride) (PVDF)/nanoclay composites were prepared using melt compounding. The effect of acrylic rubber (ACM) as a compatibilizer on different polymorph formation and on the ferroelectric properties of nanocomposites were investigated. The intercalation and morphological structure of the samples were studied using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The infrared spectroscopy and X-ray analysis revealed the coexistence of β and γ crystalline forms in PVDF-clay nanocomposite, while in partially miscible PVDF/ACM/clay hybrids, three polymorphs of α, β and γ coexisted. The coefficients of electric field-polarization (E-P) Taylor expansion were calculated based on the Lorentz theory. Using a genetic algorithm, complex dielectric susceptibilities as well as the dielectric constants for each sample were calculated and optimized. The predicted dielectric constants were found to be in good agreement with the experimental results. A dielectric constant of 16 (10 Hz) was obtained for PVDF/ACM/clay (90/10/5), which was 40% higher than that of the PVDF-clay (100/5) nanocomposite without ACM. The improved dielectric performance of the nanocomposites can be attributed to the compatibilizing effect of ACM, which facilitated the growth of β polymorph in the sample.

Dielectric characterization of conducting textiles using free space transmission measurements: accuracy and methods for improvement

The dielectric behaviour of in-situ polymerized thin polypyrrole (PPy) films on synthetic textile substrates were obtained in the 1–18 GHz region using free space transmission and reflection methods. The PPy/para-toluene-2-sulphonic acid (pTSA) coated fabrics exhibited an absorption dominated total shielding effectiveness (SE) of up to −7.34 dB, which corresponds to more than 80% of incident radiation. The permittivity response is significantly influenced by the changes in ambient conditions, sample size and diffraction around the sample. Mathematical diffraction removal, time-gating tools and high gain horns were utilized to improve the permittivity response. A narrow time-gate of 0.15 ns produced accurate response for frequencies above 6.7 GHz and the high gain horns further improved the response in the 7.5–18 GHz range. Errors between calculated and measured values of reflection were most commonly within 2%, indicating good accuracy of the method.

Determination of rate constants using microelectrodes

An understanding of the rate and the mechanism of reaction is of fundamental importance in the many facets of chemistry. Electrochemical systems are further complicated by the heterogeneous boundary, between the solution and the electrode, that the electron passes through before any electrochemical reaction can take place. This thesis concerns the development of methods for analysing electrode kinetics. One part involves the further development of the Global Analysis procedure to include electrodes with a spherical geometry which are traditionally the most popular form of electrodes. Simulated data is analysed to ascertain the accuracy of the procedure and then the known artifacts of uncompensated solution resistance and charging current are added to the simulated data so that the effects can be observed. The experimental analysis of 2-methyl-2-nitropropane is undertaken and comparisons are made with the Marcus-Hush electrochemical theories concerning electrode kinetics. A related section explores procedures for the kinetic analysis of steady state voltammetric data obtained at microdisc electrodes. A method is proposed under the name of Normalised Steady State Voltammetry and is tested using data obtained from a Fast Quasi-Explicit Finite Difference simulation of diffusion to a microdisc electrode. In a second area of work using microelectrodes, the electrochemical behaviour of compounds of the general formula M(CO)3(η3 - P2P1) where M is either Cr, Mo or W and P2P' is bis(2-diphenylphosphinoethyl)phenylphosphine) is elucidated. The development of instrumentation and mathematical procedures relevant to the measurement and quantitation of these systems is also investigated. The tungsten compound represents the first examples where the 17-electronfac+ and mer+ isomers are of comparable stability.

Microwave dielectric properties of PTFE/rutile nanocomposites

The effects of nano-size rutile filler on the microwave dielectric properties of PTFE composites were investigated and the results were compared with that of micron size rutile filled composites. Nano-size rutile powder was prepared through sol–gel route and the filled PTFE composites were fabricated through SMECH process. Different characterization techniques such as powder X-ray diffraction, SEM, BET, TEM and TG/DSC were employed to analyze the nature of ceramic filler. The dielectric properties of filled composites were evaluated at microwave frequency region using waveguide cavity perturbation technique. Different theoretical models have been employed to predict the variation of dielectric constant with respect to filler loading. The moisture absorption characteristics of nano-rutile filled PTFE composites were measured as per IPC-TM-650 2.6.2 standards. Composites show high dielectric constant at X-band frequency region with relatively high loss tangent compared to micron size counterpart.

Preparation, characterization and dielectric properties of temperature stable SrTiO3/PEEK composites for microwave substrate applications

Poly(ether ether ketone) (PEEK) is a potential candidate for electronic applications due to its low permittivity, low loss, high melting point, better chemical resistance, excellent insulating properties and easy processibility. Present paper discusses the preparation and characterization of SrTiO3 filled PEEK composite for microwave substrate applications. The dielectric constant, dielectric loss and temperature variation of dielectric constant of the composites have been studied up to 1 MHz using an Impedance Analyzer. Different theoretical approaches have been employed to predict the effective permittivity of composite systems and the results are compared with that of the experimental data. The crystallinity of the bulk composite is studied by X-ray diffraction studies. Scanning electron microscopic technique has been employed to study the dispersion of the particulate filler in PEEK matrix. Vickers hardness of pure and filled PEEK composite has been measured using Microhardness Tester. The effect of particle size on the dielectric as well as mechanical properties of SrTiO3/PEEK composite system is also studied by incorporating micronsize and nanosize fillers. Present study shows that a temperature stable composite can be realized by judiciously selecting appropriate filler concentration in the PEEK matrix.

High frequency dielectric response of the ionic liquid N-methyl-N-ethylpyrrolidinium dicyanamide

A study of the room-temperature ionic liquid N-methyl-N-ethylpyrrolidinium dicyanamide by dielectric relaxation spectroscopy over the frequency range 0.2 GHz ≤ ν ≤ 89 GHz has revealed that, in addition to the already known lower frequency processes, there is a broad featureless dielectric loss at higher frequencies. The latter is probably due to the translational (oscillatory) motions of the dipolar ions of the IL relative to each other, with additional contributions from their fast rotation.

Broadband dielectric response of the ionic liquid N-methyl-N-ethylpyrrolidinium dicyanamide

Dielectric relaxation measurements as a function of temperature, and of concentration in a non-coordinating solvent, the first reported for an ionic liquid, indicate a crossover in the relaxation mechanism due to varying levels of ion aggregation and the interplay of formation kinetics and relaxation dynamics of associates.

Dielectric properties of conducting polymer

The dielectric properties of conducting polymer composites containing polypyrrole (PPy) crushed films, PPy powder, polyaniline (PAn) base and acid powders as the dispersants and silicone rubber and vinyl ester as matrix materials have been investigated in the frequency range 2-18 GHz. The dielectric parameters such as the real part, epsiprime, and imaginary part, epsiPrime, of the permittivity and loss tangent, tandelta, increase with increasing conductivity and concentration of the dispersant. The geometrical shape of the dispersant governs the ability of conductive network formation which is indicated by a large drop in the resistivity of the composite. Also, dispersant/matrix interactions and physical properties of the matrix influence the agglomeration of the dispersant phase which, in turn, affects the dielectric properties of the composites. Flakes of PPy obtained by crushing highly conductive films and large PAn powder aggregates were unable to form a conducting network. The composites without a network of dispersant exhibit low dielectric parameters. On the other hand, high values of tan delta ranging from 0.7–1.1 were achieved for the PPy powder (15 parts)/silicone rubber composites where a conducting network was observed.

Determining binding constants from 1H NMR titration data using global and local methods : a case study using [n]polynorbornane-based anion hosts

From data generated using 1H NMR titrations, different methodologies to calculate binding constants are compared. The ‘local’ analysis method that uses only a single isotherm (only one H-bond donor) is compared against the ‘global’ method (that includes many or all H-bond donors). The results indicate that for simple systems both methods are suitable, however, the global approach consistently provides a K a value with uncertainties up to 30% smaller. For more complex binding, the global analysis method gives much more robust results than the local methods. This study also highlights the need to explore several different modes when data do not fit well to a simple 1:1 complexation model and illustrates the need for better methods to estimate uncertainties in supramolecular binding experiments.

Design and analysis of a low actuation voltage electrowetting-on-dielectric device

This paper presents an Electrowetting-on-Dielectric (EWOD) device with optimized insulating layers operated by low actuation voltage. The device consists of an electrode array on a silicon substrate, covered by a dielectric layer and a hydrophobic layer. To characterize the performance of the device, simulations are performed for the dielectric layer of Sio₂ and the hydrophobic layer of Sio₂, Su-8 and Parylene C at different voltages. The volume finite difference approach of the Coventorware software was used to carry out the simulations. Two different molar of di-ionized water droplet were considered in the simulations. It was observed that the device having the Sio₂ dielectric layer and the Parylene C hydrophobic layer moved the 1M KCL (potassium chloride) droplet at the actuation voltage of 25V.