Electrochemical impedance spectroscopy and surface characterization techniques to study carbon dioxide corrosion product scales

Electrochemical impedance spectroscopy (EIS) was used to study carbon dioxide (CO2) corrosion product scales and their effects on further CO2 corrosion. Objectives were to determine the suitability of EIS for studying corrosion scales and to investigate the influence of environmental factors on scale formation. EIS provided useful information about protective abilities and electrochemical properties of corrosion scales. CO2 corrosion scales formed at high-temperature and pressure provided better protection than those formed at low-temperature and pressure. The level of protection of the scale formed at higher temperature and pressure increased with exposure time. EIS results were compared with coupon weight-loss measurements. Scales were analyzed using a combination of Fourier transform infrared (FTIR) analysis, x-ray diffraction (XRD), and electron microscopy.

Microwave dielectric properties of PTFE/rutile nanocomposites

The effects of nano-size rutile filler on the microwave dielectric properties of PTFE composites were investigated and the results were compared with that of micron size rutile filled composites. Nano-size rutile powder was prepared through sol–gel route and the filled PTFE composites were fabricated through SMECH process. Different characterization techniques such as powder X-ray diffraction, SEM, BET, TEM and TG/DSC were employed to analyze the nature of ceramic filler. The dielectric properties of filled composites were evaluated at microwave frequency region using waveguide cavity perturbation technique. Different theoretical models have been employed to predict the variation of dielectric constant with respect to filler loading. The moisture absorption characteristics of nano-rutile filled PTFE composites were measured as per IPC-TM-650 2.6.2 standards. Composites show high dielectric constant at X-band frequency region with relatively high loss tangent compared to micron size counterpart.

New insight into non-isothermal crystallization of PVA-graphene composites

The melt crystallization of poly(vinyl alcohol) (PVA) and PVA composites has been a controversial subject due to inconclusive evidence and different opinions for its decomposition during crystallization. Using graphene as a model, the melt crystallization of PVA and PVA-graphene composites occurring during single-cycle and multiple-cycle non-isothermal annealing processes was systematically analyzed using different characterization techniques. The results obtained using single-cycle non-isothermal annealing indicated that the entire crystallization process took place through two main stages. The graphene in the PVA matrix regulates the nucleation and crystal growth manner of the PVA, yet resulting in retardation of the entire crystallization. The FTIR and Raman spectroscopic results particularly demonstrated that the annealing process not only improved the crystallinity but also led to clear decomposition in PVA and PVA-graphene composites, such as the elimination of hydroxyl groups and the production of C=C double bonds. The newly produced C=C double bonds were found to be responsible for the retardation of PVA macromolecule crystallization and the breaking of hydrogen bonds among the hydroxyl groups in the PVA chains. In addition, the morphological observation and multi-cycle non-isothermal crystallization further confirmed the existence of decomposition based on the surface damage as well as decreased crystallization enthalpy and crystallization peak temperature. Therefore, the non-isothermal crystallizations of the pure PVA and the PVA-graphene composites were in fact the combination of non-isothermal crystallization and non-isothermal degradation processes.

Electrostatically confined plasma in segmented hollow cathode geometries for surface engineering

A segmented hollow cathode (SHC) geometry was used for electrostatic confinement of plasma, and surface engineering treatments were conducted in this arrangement. The assessed processes included plasma nitriding, reactive deposition of sputtered material, and deposition of carbonaceous films by plasma-enhanced chemical vapor deposition with a bipolar pulsed-dc power supply on steel substrates. The treated specimens exhibited uniform surface morphology and deposition layers. Characterization techniques included optical microscopy, scanning electron microscopy with energy dispersive X-ray capability, and X-ray diffraction. The advantages and potential applications of the SHC arrangement are discussed in view of these results.

Characterization of the bake-hardening behavior of transformation induced plasticity and dual-phase steels using advanced analytical techniques

The bake-hardening (BH) behavior of TRansformation Induced Plasticity (TRIP) and Dual-Phase (DP) steels after intercritical annealing (IA) has been studied using transmission electron microscopy, X-ray diffraction and three dimensional atom probe tomography. It was found for the DP steel that carbon can segregate to dislocations in the ferrite plastic deformation zones where there is a high dislocation density around the "asquenched" martensite. The carbon pinning of these dislocations, in turn, increases the yield strength after aging. It was shown that bake-hardening also leads to rearrangement of carbon in the martensite leading to the formation of rod-like low temperature carbides in the DP steel. Segregation of carbon to microtwins in retained austenite of the TRIP steel was also evident. These factors, in combination with the dislocation rearrangement in ferrite through the formation of cells and microbands in the TRIP steel after pre-straining, lead to the different bake-hardening responses of the two steels.

Application of advanced experimental techniques for the microstructural characterization of nanobainitic steels

A 0.79C-1.5Si-1.98Mn-0.98Cr-0.24Mo-1.06Al-1.58Co (wt%) steel was isothermally heat treated at 350°C bainitic transformation temperature for 1 day to form fully bainitic structure with nano-layers of bainitic ferrite and retained austenite, while a 0.26C-1.96Si-2Mn-0.31Mo (wt%) steel was subjected to a successive isothermal heat treatment at 700°C for 300 min followed by 350°C for 120 min to form a hybrid microstructure consisting of ductile ferrite and fine scale bainite. The dislocation density and morphology of bainitic ferrite, and retained austenite characteristics such as size, and volume fraction were studied using Transmission Electron Microscopy. It was found that bainitic ferrite has high dislocation density for both steels. The retained austenite characteristics and bainite morphology were affected by composition of steels. Atom Probe Tomography (APT) has the high spatial resolution required for accurate determination of the carbon content of the bainitic ferrite and retained austenite, the solute distribution between these phases and calculation of the local composition of fine clusters and particles that allows to provide detailed insight into the bainite transformation of the steels. The carbon content of bainitic ferrite in both steels was found to be higher compared to the para-equilibrium level of carbon in ferrite. APT also revealed the presence of fine C-rich clusters and Fe-C carbides in bainitic ferrite of both steels.

The mechanical characterization of low work hardening, high strength steel

One of the major challenges in assessing the mechanical properties of recovery annealed steel is the strain localization that occurs almost immediately on the formation of the first Lüders band, such that no or limited propagation of the Lüders band occurs along the tensile coupon. The stress raiser associated with the geometry of the standard tensile coupon means that this plastic deformation is often completely outside the standard extensometers on the coupon. Hence, no strain is measured during the test. While this is not important for assessing the tensile strength of the steel, it does mean that the strain related properties, such as the elastic limit of the steel, cannot be measured using standard testing techniques.This work addresses this issue by examining three techniques for ensuring that the strain occurs inside the extensometer. It is shown that the best technique is the extended extensometer, where the gauge length covers slightly more than the tensile coupon parallel length. While this leads to some variation in the width of the material being measured, compensation can be be made by adjusting the strain to correct the Young's Modulus.This technique has direct implications not just for recovery annealed steels, but for other high strength, low work hardening materials such as ultrafine ferrite. A particular requirement of these high strength steels in structural applications is a high elastic limit; hence, measurement of the strain related properties for these high strength materials must be considered vital in their mechanical assessment.

Isolation and characterization of polyunsaturated fatty acid producing Thraustochytrium species : screening of strains and optimization of omega-3 production

An isolation program targeting Thraustochytrids (marine fungoid protists) from 19 different Atlantic Canadian locations was performed. Sixty-eight isolates were screened for biomass, total fatty acid (TFA), eicosapentaenoic acid (EPA), and docosahexaenoic acid (DHA) content. Analysis of fatty acid methyl ester results discerned four distinctive clusters based on fatty acid profiles, with biomass ranging from 0.1 to 2.3 g L−1, and lipid, EPA, and DHA contents ranging from 27.1 to 321.14, 2.97 to 21.25, and 5.18 to 83.63 mg g−1 biomass, respectively. ONC-T18, was subsequently chosen for further manipulations. Identified using 18S rRNA gene sequencing techniques as a Thraustochytrium sp., most closely related to Thraustochytrium striatum T91-6, ONC-T18 produced up to 28.0 g L−1 biomass, 81.7% TFA, 31.4% (w/w biomass) DHA, and 4.6 g L−1 DHA under optimal fermentation conditions. Furthermore, this strain was found to produce the carotenoids and xanthophylls astaxanthin, zeaxanthin, canthaxanthin, echinenone, and β-carotene. Given this strain’s impressive productivity when compared to commercial strains, such as Schizochytrium sp. SR21 (which has only 50% TFA), coupled with its ability to grow at economical nitrogen and very low salt concentrations (2 g L−1), ONC-T18 is seen as an ideal candidate for both scale-up and commercialization.

Characterization of membranes with X-ray ultramicroscopy

Non-invasive characterization and observation of synthetic membranes is an important practice to monitor the performance of membrane process. Primarily there are two techniques—optical and non-optical for this purpose. Among them, X-ray computed tomography, as a non-optical technique, has been extensively used for the measurement of fibre distribution and air pockets trapped in the modules. However, the micro resolution of most commercial systems has limited its application which can hardly be used for the sub-micro characterization of membrane processes. A novel micro and nano characterization method is introduced in the current work by exploring an innovative development of the X-ray ultramicroscope (XuM) and micro-tomographic techniques. The XuM, based on using a scanning electron microscope as host, provides a new approach to X-ray projection microscopy. It has demonstrated the ability to characterize very small features in objects, down to of order 100 nm, including the use for dry, wet and even liquid samples. It can also distinguish objects with very subtle difference in density.

Self-assembled natural rubber/silica nanocomposites : its preparation and characterization

A novel natural rubber/silica (NR/SiO2) nanocomposite is developed by combining self-assembly and latex-compounding techniques. The results show that the SiO2 nanoparticles are homogenously distributed throughout NR matrix as nano-clusters with an average size ranged from 60 to 150 nm when the SiO2 loading is less than 6.5 wt%. At low SiO2 contents (less-than-or-equals, slant4.0 wt%), the NR latex (NRL) and SiO2 particles are assembled as a core-shell structure by employing poly (diallyldimethylammonium chloride) (PDDA) as an inter-medium, and only primary aggregations of SiO2 are observed. When more SiO2 is loaded, secondary aggregations of SiO2 nanoparticles are gradually generated, and the size of SiO2 cluster dramatically increases. The thermal/thermooxidative resistance and mechanical properties of NR/SiO2 nanocomposites are compared to the NR host. The nanocomposites, particularly when the SiO2 nanoparticles are uniformly dispersed, possess significantly enhanced thermal resistance and mechanical properties, which are strongly depended on the morphology of nanocomposites. The NR/SiO2 has great potential to manufacture medical protective products with high performances.

The characterization and chemical reactivity of powdered wool

Wool powders with various particle sizes have been produced using different milling techniques. Scanning electron microscopy (SEM) showed gradual breakdown of the fibre as it was progressively converted into powder form. Chlorination enhanced the effectiveness of subsequent air-jet milling. X-ray photoelectron spectroscopy (XPS) revealed an increase in the surface concentrations of oxygen and nitrogen, and a decrease in carbon and sulphur on conversion of the fibres into powders, as the cortex became exposed on the powder surface. An increased surface concentration of cysteic acid was observed for the chlorinated powder. Rapid uptake of dye by wool powders was observed in situations where there was virtually no uptake by the original fibre. Hydrophobic dyes were more readily sorbed than were hydrophilic dyes. The chlorination treatment led to a decrease in the sorption of acid dyes. Confocal microscopy, used in conjunction with a fluorescent stain, showed that chemicals were able to penetrate wool particles, even at room temperature. The rate and extent of uptake of dye by the finer powders were comparable to that obtained with activated charcoal, even though the surface area of the charcoal was 100 times greater.

Characterization of high fluid strain micro contractions to study the stress on biological fluids

Microfluidics has the potential to enhance the understanding of the biological fluids under strain, due to the laminar nature of the fluid and the possibility to mimic the real conditions. We present advances on charaterization of a microfluidic platform to study high strain rate flows in the transport of biological fluids. These advances are improvements on the reproduction of a  constant extensional strain rate using micro contractions and development of 3D numerical models. The micro geometries have been fabricated in polydimethyl siloxame (PDMS) using standard soft-lithography techniques with a photolithographically patterned mold. A comparison of some microcontractions with different funnel characteristics is presented. The Micro Particle Image Velocimetry technique has been applied to validate the numerical simulations. We demonstrate the use of microfluidics in the reproduction of a large range of controllable extensional strains that can be used in the study of the effect of flow on biological fluids.

Microstructural characterization of the austenite behaviour during metadynamic recrystallization

The work discusses the recent findings obtained from the microstructural characterization of an austenitic Ni-30%Fe model alloy during metadynamic recrystallization (MDRX) using both EBSD and TEM techniques. The characterization of the grain structure, texture and dislocation substructure evolution of the fully dynamically recrystallized (DRX) microstructure during post deformation annealing revealed a novel softening mechanism occurring under the current experimental conditions. It is proposed that the initial softening stage involves rapid growth of the dynamically formed nuclei and migration of the mobile boundaries in correspondence with the well-established MDRX mechanism. However, the sub-boundaries within DRX grains progressively disintegrate through dislocation climb and dislocation annihilation, which ultimately leads to the formation of dislocation-free grains. Consequently, the DRX texture largely remains preserved throughout the annealing process.

Studies of CO2 corrosion product scales using electrochemical impedance spectroscopy and surface characterisation techniques

Electrochemical impedance spectroscopy (EIS) was used to study carbon dioxide (CO2) corrosion product scales and their effects on further CO2 corrosion. Objectives were to determine the suitability of EIS for studying corrosion scales and to investigate the influence of environmental factors on scale formation. EIS provided useful information about protective abilities and electrochemical properties of corrosion scales. CO2 corrosion scales formed at high-temperature and pressure provided better protection than those formed at low-temperature and pressure. The level of protection of the scale formed at higher temperature and pressure increased with exposure time. EIS results were compared with coupon weight-loss measurements. Scales were analyzed using a combination of Fourier transform infrared (FTIR) analysis, x-ray diffraction (XRD), and electron microscopy