Studies of a wear resistant cast iron

 The objective of this investigation was to set down (on the base of the results obtained by the examination of white cast iron alloys with different content of the alloying elements) a correlation between chemical composition and microstructure, on one hand, and the properties relevant for this group of materials, i.e., abrasion wear resistance and fracture toughness, on the other. Experimental results indicate that the volume fracture of the carbide phase, carbide size and distribution, as well as the morphology of eutectic colonies, had an important influence on the wear resistance of white cast iron alloys under low-stress abrasion conditions, whereas fracture toughness was determined largely by the matrix microstructure.

In-situ precipitation of TiC upon PTA hardfacing with grey cast iron and titanium for enhanced wear resistance

Titanium and grey cast iron powders were blended and deposited by plasma transferred arc onto mild steel substrates. The powders were injected directly into the arc by a stream of inert gas. The grey cast iron provided the iron matrix and the excess carbon content for reaction and precipitation of titanium carbides. The microstructure of the overlay was analysed by optical microscopy and scanning electron microscopy, and the respective phases were identified by X-ray diffraction. Microhardness measurements were taken from representative areas and the wear behaviour was assessed under low-stress abrasion conditions. The results show that the addition of titanium produced a significant change in the microstructure of the overlays, increased surface hardness and enhanced wear resistance compared to overlays produced without titanium.

Machinability assessment and surface integrity characteristics of Austempered Ductile Iron (ADI) using ultra-hard cutting tools

The application of austempered ductile iron (ADI) is gaining an ever greater share of the worldwide ferrous product market, specifically centering on the aerospace, automotive and shipping industries. ADI is a heat treated cast iron, which exhibits remarkable mechanical properties and provides an attractive material for designers and engineers to displace conventional materials. Previous attempts, however, to machine ADI using carbide or ceramic cutting tools produced poor tool life characteristics due to the relatively poor machinability of the workpiece. This paper presents a research study that has applied the advanced technology of modern ultrahard cutting tools, in an attempt to achieve enhanced machinability performance. This performance was evaluated through the analysis of cutting forces, tool wear, surface finish and roundness.

A comparative assessment of austempered ductile iron as a substitute in weight reduction applications

Manufacturing engineering has had to undergo drastic changes in the approach to material selection in order to meet new design challenges. In the automotive industry, researchers in their effort to reduce emissions and satisfy environmental regulations, have shifted their focus to new emerging materials such as high-strength aluminium alloys, metal matrix composites, plastics, polymers and of late, Austempered Ductile Iron (ADI). ADI is a good choice for design where the criterion is high performance at reduced weight and cost. The unique, ausferrite microstructure gives the material desirable material properties and an edge over other materials. A comparative study of ADI in terms of materials properties and machining characteristics with other materials is desirable to highlight the potential of the material. This paper focuses on a comparative assessment of material and machining characteristics of ADI for different applications. The properties under consideration are machinability, weight and cost savings and versatility. ADI has a higher strength-to-weight ratio than aluminium making it a ready alternative for material selection. In terms of machinability, there are some problems associated with machining of ADI due to its work hardening nature. This paper attempts to identify the possible potential applications of ADI, by critically reviewing specific applications such as machinability, overall economics and service.

Wear characteristics of ultra-hard cutting tools when machining austempered ductile iron

Nodularised Ductile Cast Iron, when subjected to heat treatment processes - austenitising and austempering produces Austempered Ductile Iron (ADI). The microstructure of ADI also known as "ausferrite" consists of ferrite, austenite and graphite nodules. Machining ADI using conventional techniques is often a problematic issue due to the microstructural phase transformation from austenite to martensite during machining. This paper evaluates the wear characteristics of ultra hard cutting tools when machining ADI and its effect on machinability. Machining trials consist of turning ADI (ASTMGrade3) using two sets of PCBN tools with 90% and 50% CBN content and two sets of ceramics tools; Aluminium Oxide Titanium Carbide and Silicon Carbide - whisker reinforced Ceramic. The cutting parameters chosen are categorized as roughing and finishing conditions; the roughing condition comprises of constant cutting speed (425 m/min) and depth of cut (2mm) combined with variable feed rates of 0.1, 0.2, 0.3 and 0.4mm/rev. The finishing condition comprises of constant cutting speed (700 m/min) and depth of cut (0.5mm) combined with variable feed rates of 0.1, 0.2, 0.3 and 0.4mm/rev. The benchmark condition to evaluate the performance of the cutting tools was tool wear evaluation, surface texture analysis and cutting force analysis. The paper analyses thermal softening of the workpiece by the tool and its effect on the shearing mechanism under rough and finish machining conditions in term of lower cutting forces and enhanced surface texture of the machined part.

A case study on effect of feed rate on machinability of austempered ductile iron

Austempered Ductile Iron (ADI) is a type of nodular, ductile cast iron subjected to heat treatments - austenitising and austempering. Whilst machining is conducted prior to heat treatment and offers no significant difficulty, machining post heat treatment is demanding and often avoided. Phase transformation of retained austenite to martensite leading to poor machinability characteristics is a common problem experienced during machining. This case study explains the effect of feed rate on machinability of ADI using cutting force analysis and tool failure analysis. The experimental design consists of conducting drilling trials on grade 1200 and 1400 at constant depth of cut, 25mm; constant speed, 45m/min; no coolant and variable feed rates from 0.2 to 0.35 mm/rev (increment of 0.025mm/rev). Metallography and X-ray diffraction technique was carried out in order to identify and quantify the microstructural phases before and after drilling. The results from the trial infer that the best way to machine ADI efficiently without tool failure is using low feeds and high speeds and without coolant.

Recent advances in machining of Austempered Ductile Iron to avoid machining induced microstructural phase transformation reaction

Austempered Ductile Iron (ADI) is a type of nodular, ductile cast iron subjected to heat treatments-austenitising and austempering. Whilst machining is conducted prior to heat treatment and offers no significant difficulty, machining post heat treatment is demanding and often avoided. Phase transformation of retained austenite to martensite leading to poor machinability characteristics is a common problem experienced during machining. Study of phase transformations is an investigative study on the factors-plastic strain (εp) and thermal energy (Q) which effect phase transformations during machining. The experimental design consists of face milling grade 1200 at variable Depth of Cut (DoC) range from 1 to 4 mm, coolant on/off, at constant speed, 1992 rpm and feed rate, 0.1 mm/tooth. Plastic strain (εp) and martensite content (M) at fracture point for each grade was evaluated by tensile testing. The effect of thermal energy (Q) on phase transformations was also verified through temperature measurements at DoC 3 and 1 mm using thermocouples embedded into the workpiece. Finally, the amount of plastic strain (εp) and thermal energy (Q) responsible for a given martensite increase (M) during milling was related and calculated using a mathematical function, M=f (εp, Q). The future work of the thesis involves an in-depth study on the new link discovered through this research: mathematical model relating the role of plastic strain and thermal energy in martensite formation.

Slurry pump side-liner wear : comparison of some laboratory and field results

The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for particles larger than d8The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle 10 size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different 11 material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle 12 size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are 13 also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab 14 tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for 15 particles larger than d₈₅ of about 700mm. © 2001 Elsevier Science B.Y. All rights reserved.

Influence of chromium content on the dry machining performance of cathodic arc evaporated TiA1N coatings

Physical vapour deposition (PVD) titanium aluminium nitride coated cutting tools are used extensively in global manufacturing for reducing production costs and improving productivity in a number of aggressive metal-cutting operations, namely, dry and high-speed machining. In this investigation, the performance of Ti1−xAlxN and Ti1−x−yAlxCryN coatings was assessed on Co-HSS twist drills used to machine grey cast iron. The failure criterion for drills was defined as a critical sized flank wear land at the outer corners of the drills. Using this criterion, the average tool life of uncoated twist drills was increased by factors of 2.5, 3.0 and 3.0 by Ti0.59Al0.41N, Ti0.27Al0.19Cr0.54N and Ti0.21Al0.14Cr0.65N coatings, respectively. Notwithstanding the similar increase in average tool life, the Ti1−x−yAlxCryN coatings produced more consistent results than the Ti1−xAlxN coated drills with standard deviations of 67, 3 and 19 holes, respectively. This result has significant practical implications in manufacturing, since drills are not replaced on an individual basis, but rather on a preset tool change frequency. The present paper discusses the performance of Ti1−xAlxN and Ti1−x−yAlxCryN coated drills in terms of average and practical drill life and concludes with remarks on the characterisation of PVD coatings and their significance on the performance of Co-HSS twist drills when dry machining grey cast iron.

Reducing the macroparticle content of cathodic arc evaporated TiN coatings

Cathodic arc evaporation (CAE) is a widely used technique for generating highly ionised plasma from which hard, wear-resistant PVD coatings can be deposited. A major drawback of this technique is the emission of micrometer-sized droplets of cathode material from the arc spot, which are commonly referred to as ‘macroparticles’. In this study, the effect of cathode poisoning was investigated as a method to reduce the number of macroparticles in PVD coatings. While the study focuses on the reduction of macroparticles in titanium nitride coatings, the outcomes and key findings can be broadly applied to the cathodic arc process, in particular, for the reduction of macroparticles in more advanced CAE coatings. The results support earlier findings that have shown that poisoning of the cathode can reduce the number of macroparticles emitted from the arc spot. The results of glow discharge optical emission spectroscopy (GD-OES) showed that the titanium content of the coatings varied little between the respective coatings despite changes in the deposition pressure from 0.1 to 1.2 Pa. The GD-OES results also showed the presence of oxide contamination at the surface of the coatings, which was significantly reduced with increasing deposition pressure. The coatings were also deposited onto high-speed steel twist drills to compare the metal-cutting performance when dry drilling a workpiece of cast iron. The results of the drill tests showed that tool life increased with a reduction in the number of macroparticles.

Recrystallization kinetic study of copper-bearing strip cast steels

The effects of copper on as-cast structure, recrystallization and precipitation kinetics of strip cast low carbon steel were investigated. As-cast microstructure mainly consists of polygonal ferrite and Widmanstatten ferrite. Recrystallization responses were strongly dependent on initial microstructure and Cu content. Precipitation strengthening was observed in high copper content alloys.