Slurry pump side-liner wear : comparison of some laboratory and field results

The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for particles larger than d8The current work compares some slurry pump lab wear results with the wear found across different field applications with d₈₅ particle 10 size ranging from 100 to 4000mm. Side-liner wear life data has been collected for two different impeller geometries and two different 11 material classes (cast iron and natural rubber). Different field wear patterns have been photographed and categorised on the basis of particle 12 size. The field wear patterns showed close similarity to the lab wear patterns particularly in the areas of localised gouging. Wear rates are 13 also compared for the different geometries. Overall trend of wear with particle size for the white iron parts was similar to the grey iron lab 14 tests albeit at significantly lower wear rates. In general, the wear with the rubber side-liner was less at smaller particle sizes but greater for 15 particles larger than d₈₅ of about 700mm. © 2001 Elsevier Science B.Y. All rights reserved.

Frictional behaviour and wear performance of a nitrocarburised coating sliding against AISI 1019 steel

This work employed a commercial nitrocaburising process to diffuse a coating onto M2 grade high speed tool steel. Properties of the nitrocaburised coating (CN) such as thickness, roughness and hardness were characterised using a variety of techniques including Glow-Discharge Optical Emission Spectrometry (GD-OES) and Scanning Electron Microscopy (SEM). A tribological test has been developed in which two nominally identical crossed cylinders slide over each other under selected test conditions. The test has been employed to investigate the wear performance of both CN coated and uncoated M2 specimens and frictional behaviour of the sliding interface between the tool and a AISI 1019 steel workpiece under unlubricated (dry) and lubricated conditions. Fourier Transform Infrared Spectroscopy (FTIR) was used to monitor the formation of chemical species from the oxidation of lubricant during tribological testing.

Pin on disc wear investigation of nitrocarburised H13 tool steel

Nitrocarburised H13 disks were tested in dry, sliding wear against a stationary ruby ball (pin). Three different 4 h nitrocarburising treatments were compared, using N2/NH3/CO2, N2/NH3/natural gas and N2/NH3 gas mixtures, resulting in compound layers of varying thickness, hardness, porosity and oxide morphology. During mild, oxidative wear, with the formation of abrasive wear debris, the most brittle and oxidised surfaces performed poorly. Polishing to a bright, reflective finish greatly reduced wear. However, the N2/NH3/CO2 sample also frequently maintained a 'very mild' wear regime, owing to the formation of a protective film between the wear surfaces, and resulting in a lowering of the friction coefficient. This treated surface was porous and covered in a complex layer of coarse oxide+epsi-carbonitride. Nitrocarburised samples and wear tracks were characterised by optical microscopy, SEM, atomic force microscopy and stylus profilometry.

Theoretical investigation of wear-resistance mechanism of superelastic shape memory alloy NiTi

Recent experimental research indicates that superelastic shape memory alloy nickel–titanium (NiTi) is superior to stainless steel against wear and could be applied in tribological engineering. It is believed that the super wear resistance of shape memory alloys is mainly due to the recovery of the superelastic deformation. Our recent wear study indicates that wear rate is very sensitive to the maximum contact pressure. In the present investigation, which involves applying Hertz contact theory and the finite element method, the wear behaviour of shape memory alloys is examined against that of stainless steels through analyzing the maximum contact pressure and the plastic deformation. Our investigation indicates that the contribution of superelasticity to the high wear resistance of NiTi is directly linked to the low transformation stress and the large recoverable transformation strain. Furthermore, the low Young's modulus of this alloy also plays an important role to reduce the maximum contact pressure and therefore reduce the wear rate. Additionally, the high plastic yield strength of transformed martensite NiTi enhances its wear resistance further.

Contact pressure and wear in sheet metal forming - an FEM analysis

Wear is the principal cause of tool failure in most sheet metal forming processes. It is well known that the contact pressure between the blank and the tool has a large influence on the wear of the tool, and hence the tool life. This investigation utilises the finite element method to analyse the contact pressure distribution over the die radius for a particular deep drawing process. Furthermore, the evolution of the predicted contact pressure distribution throughout the entire stroke of the punch is also examined. It was found that the majority of the process shows a steady state pressure distribution, with two characteristic peaks over the die radius, at the beginning and end of the sheet contact area. Interestingly, the initial transient contact pressure response showed extremely high localised peak pressures; more than twice that of the steady state peaks. Results are compared to wear reported in the literature, during similar experimental deep drawing processes. Finally, the significance and effect of the results on wear and wear-testing techniques are discussed.

Contact pressure evolution and its relation to wear in sheet metal forming

For a given sheet metal forming process, an accurate determination of the contact pressure distribution is an essential step towards the estimation of tool life. This investigation utilizes finite element (FE) analysis to model and explain the evolution and distribution of contact pressure over the die radius, throughout the duration of a channel forming process. It was found that a typical two-peak steady-state contact pressure response exists for the majority of the process. However, this was preceded by an initial transient response, characterized by extremely large and localized contact pressures, which were more than double the magnitude of the steady-state peak pressure. The validity of the predicted contact pressure behavior was assessed via detailed numerical analysis and by examining the wear response of an experimental stamping operation. The experimental results revealed that the high contact pressure zones of the transient response corresponded to a severe galling wear mechanism. Therefore, the transient response may be of primary significance to the tool wear response; thus questioning the applicability of traditional bending-under-tension wear tests for sheet metal stamping processes. Finally, a parametric study was conducted, examining the influence of the major process parameters on the steady-state and peak transient contact pressures, using the developed FE model. It was found that the bend ratio and the blank material ultimate tensile strength had the most influence on the peak contact pressures. The main process-related parameters, friction coefficient and blank holder force, were found to have only a minor influence.

FEA simulation of contact and wear between non-metallic materials for accelerated new product development

The conventional approach ie laboratory life testing to examine the reliability of products takes long time and involves tremendous cost as samples are tested till failures. The accelerated life test (ALT) has recently been used as an alternative method. Although ALT reduces the cost of reliability testing through applying more severe environmental conditions than the normal ones, it is no longer sufficient as it does not describe the process of products’ failure explicitly and it is still highly dependent on physical testing. Consequently, novel practices need to be developed for better understanding of the products’ reliability. A novel Finite Element Analysis (FEA) model incorporating mathematical wear equations is developed in the current work and applied to polymer materials. Wear rate, a key parameter, is calculated by using a combinatorial formula that combines a conventional linear equation with a recently published exponential equation. The local wear is firstly calculated and then integrated over the sliding distance. The FEA simulation works in a loop and performs a series of simulation with updated surface geometries. The simulation is in good agreement with the physical testing result.

Wear attributes of cashmere single jersey knitted fabrics blended with high and low crimp superfine merino wool

In a replicated experiment, we investigated the impact of cashmere in blends with superfine wools on the wear attributes of single jersey knitted fabrics. We also investigated the relative performance of low crimp/low fiber curvature superfine wool when compared with cashmere and also when compared with traditional high crimp/high fiber curvature superfine wool in pure and blended knitted fabrics. Wool type, blend ratio and fabric structure affected fabric air permeability, resistance to pilling and change in appearance, relaxation shrinkage, hygral expansion, and dimensional stability during laundering. The responses to variation in fiber crimp were much greater than previously reported. The fabric properties of low crimp wool differed significantly from those made from high crimp wool, and low crimp wool fabric properties differed significantly from, but were closer to, the fabric properties of cashmere, compared with high curvature wool.

Wear in centrifugal slurry pumps

The project improves understanding of wear in slurry pumps. By measuring actual pump wear and microscopically examining worn surfaces, a clearer picture emerged of wear modes and mechanisms for different materials. This enables improved guidelines for material selection and modifications to hydraulic shape that increased pump wear life.

Modelling of tooling wear in trim dies for AHSS

Using Advanced High Strength Steels (AHSS) in forming and cutting dies generates higher loads in tools. Tool wear is an issue when applying AHSS. This study investigates the effect of process parameters such as clearance, material properties and punch/die bluntness on contact pressure values and tool wear. Some desirable process parameters that minimise wear have been found.

Tool wear analysis in sheet metal stamping

This thesis advances the understanding of die wear in sheet metal stamping. It was found that transient conditions exist at the die radius, resulting in severe contact pressures that are critical to the wear behaviour. The findings challenge applicability of traditional wear tests and models for sheet metal stamping processes.

Transition in wear performance for ionic liquid lubricants under increasing load

The effect of ionic liquid (IL) lubrication for aluminium/steel systems is highly dependant on the applied load and the IL structure. This study illustrates that a change in anion of an IL lubricant results in different physicochemical properties that will alter its performance at a given load. As the load is increased there is a shift in lubricant performance and mechanism of the IL. Up to a load of 30 N the lowest wear coefficient was achieved by a phosphonium diphenylphosphate IL, whilst above 30 N a phosphonium bis(trifluoromethanesulfonyl)amide IL was able to form a more tenacious tribolayer that resulted in the lowest wear.

Deformation and frictional heating in relation to wear in sheet metal stamping

In the automotive industry, press production rates often need to be reduced in order to minimize tool wear issues and successfully stamp advanced high strength steels. This indicates that heating affects may be important. This paper examines friction and deformational heating at the die radius during sheet metal stamping, using finite element analysis. The results show that high temperatures, of up to 130°C, can occur at the die radius surface. Such behavior has not been previously reported in the literature, for what is expected to be ‘cold’ sheet metal stamping conditions. It will be shown that the temperature rise is due to the increased contact stresses and increased plastic work, associated with stamping AHSS. Consequently, new insights into the local contact conditions in sheet metal stamping were obtained. The outcomes of this work may impact the wear models and tests employed for future tool wear analyses in sheet metal stamping.