Reclaiming spent liquor from cotton reactive dyebaths using nanofiltration membrane for possible reuse of water and salt

During dyeing, salts are placed in a dyebath to aid the fixation of various dyes on to the fabric while bases are added to raise the pH from around neutral to pH 11. Afterwards, the used dyebath solution, called dyebath spent liquor, is discharged with almost all the salts and bases added as well as unfixed dyes. Consequently, a lot of raw materials are lost in the waste stream ending up in the environment as pollutants. In this study, possibilities of reusing water and salts of dyebathes were investigated, using a nanofiltration membrane. When the salt concentration in the spent liquor was increased from 10 to 80 g/L, the salt rejection by membrane was found to decrease initially; however, the salt rejection increased over the time, which was not expected. The aggregation of dye was also studied and found to decrease in the concentrate when the salt concentration was increased. This may be due to the aggregation of salt in the concentrate, which explains the increase in salt rejection. This information is useful for the textile industry in evaluating the treated water quality for the purpose of reuse.

Nanofiltration for the possible reuse of water and recovery of sodium chloride salt from textile effluent

During the reactive dyeing of cotton, salts such as sodium chloride (NaCI) are placed in a dyebath to aid the exhaustion of various dyes onto the fabric while bases are added to raise the pH from around neutral to pH 11 to achieve fixation. Afterwards, the used dyebath solution, called dyebath spent liquor, is discharged with almost all the salts and bases added as well as unfixed dyes. Consequently, many raw materials are lost in the waste stream ending up in the environment as pollutants. In this study possibilities of reusing the water and salts of dyebaths were investigated using a nanofiltration membrane. When the NaCI concentration in the spent liquor was increased from 10 to 80 g/L, the NaC1 rejection by the membrane was found to decrease initially; however, the NaC1 rejection increased over time, which was not expected. The aggregation of dye was also studied and found to decrease in the concentrate when the salt concentration was increased. This information is useful for the textile industry in evaluating the treated water quality for the purpose of reuse.

Ionic liquid electrolyte for lithium metal batteries : physical, electrochemical, and interfacial studies of N-Methyl-N-butylmorpholinium Bis(fluorosulfonyl)imide

The ionic liquid (IL) N-methyl-N-butylmorpholinium bis(fluorosulfonyl)imide (C₄mmor FSI) is examined from physical and electrochemical perspectives. Pulsed field gradient NMR spectroscopy shows that ion diffusivities are low compared with similar, non-ethereal ILs. Ionicity values indicate that above room temperature, less than 50% of ions contribute to conductivity.

Lithium cycling in symmetrical cells using a C₄mmor FSI-based electrolyte is best demonstrated at elevated temperatures. Specific capacities of 130 mAh g⁻¹ are achieved in a Li−LiFePO₄ battery at 85 °C. FT-IR spectroscopic investigations of lithium electrodes suggest the presence of alkoxide species in the solid electrolyte interphase (SEI), implying a ring-opening reaction of C₄mmor with lithium metal. In contrast, the SEI derived from N-methyl-N-propylpiperidinium FSI lacks the alkoxide signature but shows signs of alkyl unsaturation, and the activation energy for Li+ transport through this SEI is slightly lower than that for the C₄mmor-derived SEI. Our detailed findings give insight into the capabilities and limitations of rechargeable lithium metal batteries utilizing a C₄mmor FSI electrolyte.

Lithium doped N,N-dimethyl pyrrolidinium tetrafluoroborate organic ionic plastic crystal electrolytes for solid state lithium batteries

The organic ionic plastic crystal material N,N-dimethyl pyrrolidinium tetrafluoroborate ([C1mpyr][BF4]) has been mixed with LiBF4 from 0 to 8 wt% and shown to exhibit enhanced ionic conductivity, especially in the higher temperature plastic crystal phases (phases II and I). The materials retain their solid state well above 100 °C with the melt not being observed up to 300 °C. Interestingly the conductivity enhancement is highest with the lowest level of LiBF4 addition in phase II, but then the order of enhancement is reversed in phase I. In all cases, a conductivity drop is observed at the II → I phase transition (105 °C) which is associated with increased order in the pure matrix, as previously reported, although the conductivity drop is least for the highest LiBF4 amount (8 wt%). The 8 wt% sample displays different conductivity behaviours compared to the lower LiBF4 concentrations, with a sharp increase above 50 °C, which is apparently not related to the formation of an amorphous phase, based on XRD data up to 120 °C. Symmetric cells, Li/OIPC/Li, were prepared and cycled at 50 °C and showed evidence of significant preconditioning with continued cycling, leading to a lower over-potential and a concomitant decrease in the cell resistivity as measured by EIS. An SEM investigation of the Li/OIPC interfaces before and after cycling suggested significant grain refinement was responsible for the decrease in cell resistance upon cycling, possibly as a result of an increased grain boundary phase.

Polyterthiophene/CNT composite as a cathode material for lithium batteries employing an ionic liquid electrolyte

A polyterthiophene (PTTh)/multi-walled carbon nanotube (CNT) composite was synthesised by in situ chemical polymerisation and used as an active cathode material in lithium cells assembled with an ionic liquid (IL) or conventional liquid electrolyte, LiBF₄/EC–DMC–DEC. The IL electrolyte consisted of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF₄) containing LiBF₄ and a small amount of vinylene carbonate (VC). The lithium cells were characterised by cyclic voltammetry (CV) and galvanostatic charge/discharge cycling. The specific capacity of the cells with IL and conventional liquid electrolytes after the 1st cycle was 50 and 47 mAh g⁻¹ (based on PTTh weight), respectively at the C/5 rate. The capacity retention after the 100th cycle was 78% and 53%, respectively. The lithium cell assembled with a PTTh/CNT composite cathode and a non-flammable IL electrolyte exhibited a mean discharge voltage of 3.8 V vs Li⁺/Li and is a promising candidate for high-voltage power sources with enhanced safety.

Double-layer and solvation forces measured in a molten salt and its mixtures with water

Measurements have been made of the force between molecularly smooth mica surfaces immersed in ethylammonium nitrate, which is a molten salt at room temperature, and in mixtures of this salt with water across the concentration range from 10 -4 M to that of the pure salt, which is 11.2 M. At low concentrations the salt behaves as a typical 1:1 electrolyte, and we measure an electrical double-layer force whose range decreases with increasing salt concentration. At high concentrations, above about 1 M, the double-layer force becomes so weak and short-ranged that it is completely dominated by a solvation force extending up to 5 nm. In the pure molten salt the solvation force is an oscillatory function of surface separation comparable to that measured in simple nonpolar liquids. No monotonic component of solvation force is found.

Dietary salt loading impairs arterial vascular reactivity 1-3

BACKGROUND: Studies of sodium have shown improvements in vascular function and blood pressure (BP). The effect of chronic sodium loading from a low-sodium diet to a Western diet on vascular function and BP has been less well studied.

OBJECTIVE: The objective was to examine the effects of dietary salt intake on vascular function and BP.

DESIGN: Thirty-five hypertensive volunteers met the inclusion criteria. After a 2-wk run-in with a low-sodium diet (60 mmol/d), the participants maintained their diets and were randomly assigned to receive sequentially 1 of 3 interventions for 4 wk, with a 2-wk washout between interventions: sodium-free tomato juice (A), tomato juice containing 90 mmol Na (B), and tomato juice containing 140 mmol Na (C). The outcomes were changes in pulse wave velocity (PWV), systolic BP (SBP), and diastolic BP (DBP).

RESULTS: The difference in PWV between interventions B and A was 0.39 m/s (95% CI: 0.18, 0.60 m/s; P = 0.001) and between C and A was 0.35 m/s (95% CI: 0.13, 0.57 m/s; P = 0.01). Differences in SBP and DBP between interventions B and A were 4.4 mm Hg (95% CI: 1.2, 7.8 mm Hg; P = 0.01) and 2.4 mm Hg (95% CI: 0.8, 4.1 mm Hg; P = 0.001), respectively, and between interventions C and A were 5.6 mm Hg (95% CI: 2.7, 8.4 mm Hg; P = 0.01) and 3.3 mm Hg (95% CI: 1.5, 5.0 mm Hg; P = 0.001), respectively. Changes in PWV correlated with changes in SBP (r = 0.52) and DBP (r = 0.58).

CONCLUSIONS: Dietary salt loading produced significant increases in PWV and BP in hypertensive volunteers. Correlations between BP and PWV suggest that salt loading may have a BP-independent effect on vascular wall function. This further supports the importance of dietary sodium restriction in the management of hypertension. This trial was registered with the Australian and New Zealand Clinical Trials Registry as ACTRN12609000161224.

The effect of coordinating and non-coordinating additives on the transport properties in ionic liquid electrolytes for lithium batteries

In the present study we expand our analysis of using two contrasting organic solvent additives (toluene and THF) in an ionic liquid (IL)/Li NTf 2 electrolyte. Multinuclear Pulsed-Field Gradient (PFG) NMR, spin-lattice (T1) relaxation times and conductivity measurements over a wide temperature range are discussed in terms of transport properties and structuring of the liquid. The conductivity of both additive samples is enhanced the most at low temperatures, with THF slightly more effective than toluene. Both the anion and lithium self-diffusivity are enhanced in the same order by the additives (THF > toluene) while that of the pyrrolidinium cation is marginally enhanced. 1H spin-lattice relaxation times indicate a reasonable degree of structuring and anisotropic motion within all of the samples and both 19F and 7Li highlight the effectiveness of THF at influencing the lithium coordination within these systems.

Dietary salt intake assessed by 24 h urinary sodium excretion in Australian schoolchildren aged 5–13 years

Objective To measure total daily salt intake using 24 h urinary Na excretion within a sample of Victorian schoolchildren aged 5–13 years and to assess discretionary salt use habits of children and parents.

Design Cross-sectional study.

Setting Completed within a convenience sample of independent primary schools (n 9) located in Victoria, Australia.

Subjects Two hundred and sixty children completed a 24 h urine collection over a school (34 %) or non-school day (66 %). Samples deemed incomplete (n 18), an over-collection (n 1) or that were incorrectly processed at the laboratory (n 3) were excluded.

Results The sample comprised 120 boys and 118 girls with a mean age of 9·8 (sd 1·7) years. The average 24 h urinary Na excretion (n 238) was 103 (sd 43) mmol/24 h (salt equivalent 6·0 (sd 2·5) g/d). Daily Na excretion did not differ by sex; boys 105 (sd 46) mmol/24 h (salt equivalent 6·1 (sd 2·7) g/d) and girls 100 (sd 41) mmol/24 h (salt equivalent 5·9 (sd 2·4) g/d; P = 0·38). Sixty-nine per cent of children (n 164) exceeded the recommended daily Upper Limit for Na. Reported discretionary salt use was common: two-thirds of parents reported adding salt during cooking and almost half of children reported adding salt at the table.

Conclusions The majority of children had salt intakes exceeding the recommended daily Upper Limit. Strategies to lower salt intake in children are urgently required, and should include product reformulation of lower-sodium food products combined with interventions targeting discretionary salt use within the home.