Effect of aluminum on the corrosion resistance of low-alloy steel in 10wt% sulfuric acid solution

The aqueous corrosion behavior of low-alloy steel with aluminum contents was examined in a 10 wt% H₂SO₄ (pH 0.13) solution using electrochemical techniques and surface analyses. The corrosion resistance of the new alloy steel was evaluated in terms of electrochemical parameters, such as passive current density, film, and charge transfer resistances. The results showed that a high Al content in the steel imparted better passivation behavior resulting in a lower corrosion rate. It related to the enrichment of iron carbonate and hydrocarbon by the dissolution of the carbide phase.

Continuous corrosion rate measurement by noise resistance calculation

A commonly employed method of corrosion rate measurement is to determine the electrochemical impedance of the corroding material. One technique for estimating the impedance is the noise impedance calculation. While it has been shown to yield useful results, there are a number of problems that require attention. This paper identifies some of those problems-specifically, those of detrending and resolution-and provides a solution that allows continuous, time-varying noise resistance and noise impedance calculations to be performed with known time, frequency, and magnitude resolutions. Applications to synthetic and experimental data are included as illustrations

Effects of crystallographic orientation on corrosion behavior of magnesium single crystals

The corrosion behavior of magnesium single crystals with various crystallographic orientations was examined in this study. To identify the effects of surface orientation on the corrosion behavior in a systematic manner, single-crystal specimens with ten different rotation angles of the plane normal from the [0001] direction to the [1010] direction at intervals of 10° were prepared and subjected to potentiodynamic polarization and potentiostatic tests as well as electrochemical impedance spectroscopy (EIS) measurements in 3.5 wt.% NaCl solution. Potentiodynamic polarization results showed that the pitting potential (E _pit) first decreased from −1.57 V _SCE to −1.64 V _SCE with an increase in the rotation angle from 0° to 40°, and then increased to −1.60 V _SCE with a further increase in the rotation angle to 90°. The results obtained from potentiostatic tests are also in agreement with the trend in potentiodynamic polarization tests as a function of rotation angle. A similar trend was also observed for the depressed semicircle and the total resistances in the EIS measurements due to the facile formation of MgO and Mg(OH)₂ passive films on the magnesium surface. In addition, the amount of chloride in the passive film was found first to increase with an increase in rotation angle from 0° to 40°, then decrease with a further increase in rotation angle, indicating that the tendency to form a more protective passive film increased for rotation angle near 0° [the (0001) plane] or 90° [the (1010) plane].

A novel crevice corrosion experiment using a wire beam electrode

This paper describes a new experiment for studying crevice corrosion. A wire beam electrode was employed in this experiment to measure electrochemical parameters directly from crevice area and these parameters were used to calculate instantaneous crevice corrosion kinetics. A clear correlation between calculated corrosion depth map and real corrosion appearance was obtained.

Effect of gold on the corrosion behavior of an electroless nickel/immersion gold surface finish

The performance of surface finishes as a function of the pH of the utilized plating solution was evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests in 3.5 wt.% NaCl solution. In addition, the surface finishes were examined by x-ray diffraction (XRD), and the contact angle of the liquid/solid interface was recorded. NiP films on copper substrates with gold coatings exhibited their highest coating performance at pH 5. This was attributed to the films having the highest protective efficiency and charge transfer resistance, lowest porosity value, and highest contact angle among those examined as a result of the strongly preferred Au(111) orientation and the improved surface wettability.

Comparative study of ni effect on the corrosion behavior of low alloy steels in FGD and acid rain environments

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% H2SO4+0.35 vol.% HC1 at 60°C and an acid rain solution of 6.25 X 10-5 M H2S04+5.5 X 10-3 M NaCl at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of NiFe204 rust against Cl-ions by electronegativity.

A novel sensing technique for monitoring pitting corrosion of stainless steel type 316L

A novel electrochemically integrated multi-electrode array namely the wire beam electrode(WBE) in combination with noise signatures analysis has been designed to monitor pittingcorrosion of one of the best corrosion resistance ferrous alloys, stainless steel type 316L.From the direct correlation of electrochemical potential noise signatures and galvanic currentdistribution maps during pitting corrosion processes, two characteristic noise patterns wereobserved prior to stable pit formation: (i) the characteristic ‘peak’ of rapid potential transient,towards less negative direction, followed by recovery (termed noise signature I) was found tocorrelate with the disappearance of unstable anode; (ii) the characteristic noise pattern ofquick potential changes towards less negative direction followed by no recovery (termed noisesignature II) was found to correspond with the massive disappearance of minor anodes leadingto formation of highly localized major anodes in the galvanic current distribution maps.

Review: The preliminary study for the interpretation of electrochemical noise with continuous wavelet transform

Random fluctuations of the electrical quantities (electrode potential and cell current) in electrochemical systems commonly are referred to as electrochemical noise (ECN). The ECN signal for the corrosion of mild steel in reinforced concrete specimen was analyzed with the Continuous Wavelet Transform (CWT). The original signal was transformed into a time-frequency phase plane with colors representing the coefficients of the CWT. The signal shows a self-similarity structure in the phase plane. Through this way, the chaotic nature of corrosion process is manifested.

An auto-switch for multisampling of a wire beam electrode corrosion monitoring system

An auto-switch device has been designed, constructed, and tested for multisensor corrosion measurements. The auto-switch is able to connect/disconnect the selected wire beam electrode and/or electrode pairs under computer control. A computer controlled analog switch-array consisting of 100 inputs has been used as an essential part of the switch bank. The switch-bank is an essential component of a corrosion-monitoring instrument that is expected to find wide application in industry. The performance of the switch-bank is discussed and its effect on the signals is illustrated.