Porous bioresorbable magnesium as bone substitute

Recently magnesium has been recognized as a very promising biomaterial for bone substitutes because of its excellent properties of biocompatibility, biodegradability and bioresorbability. In the present study, magnesium foams were fabricated by using a powder metallurgical process. Scanning electron microscopy equipped with energy dispersive X~ray spectrometer (EDS) and compressive tester were used to characterize the porous magnesium. Results show that the Young's modulus and the peak stress of the porous magnesium increase with decreasing porosity and pore size. This study suggests that the mechanical properties of the porous magnesium with the low porosity of 35 % andlor with the small pore size of about 70 μ are close to those of human cancellous bones.

Porous Ti-Nb-Zr alloy through powder metallurgy for biomedical applications

This work investigated the structure and properties relationship, surface modification, biocompatibility and bioactivity of a porous Ti-Nb-Zr alloy. The porous alloy exhibited inter-connected porous structure, good biocompatibility and high mechanical strength with an elastic modulus close to that of bone. Porous Ti-Nb-Zr alloys are thus promising biomaterials for hard tissue replacement.

Fabrication of porous TiAl intermetallic compound by self-propagating high temperature synthesis

The present paper describes processing of a lotus-structured porous Ti-Al/Ti composite by SHS with Ti powder and Al rods. Ti-Al intermetallic compound was formed in a range of 200-300μm around the pore by SHS of reaction between Ti and Al, resulting in formation of a lotus-structured porous Ti-Al/Ti composite.

The detection of latent fingermarks on porous surfaces using amino acid sensitive reagents : a review

The introduction of ninhydrin treatment as a chemical technique for the visualisation of latent fingermarks on porous surfaces revolutionised approaches to forensic fingermark examination. Since then, a range of amino acid sensitive reagents has been developed and such compounds are in widespread use by law enforcement agencies worldwide. This paper reviews the development and use of these reagents for the detection of latent fingermarks on porous surfaces. A brief overview is provided, including an historical background, forensic significance, and a general approach to the development of latent fingermarks on porous surfaces. This is followed by a discussion of specific amino acid sensitive treatments.

Characterisation and impedance spectroscopy of substituted Li1.3Al0.3Ti1.7(PO4)3−x(ZO4)x (Z=V, Nb) ceramics*1

Lithium ion conducting ceramics based on the lithium aluminium titanium phosphate (LATP) NASICON structure have been prepared with various substitutions of the phosphorous. The effect of the processing method has been shown to be the key factor in determining the conductivity, both bulk and grain boundary, as well as the conductivity trends observed as a function of substitution.

Solid state NMR characterization of lithium conducting ceramics

⁷Li solid state NMR has been used to characterize lithium aluminium titanium phosphate and lithium lanthanum titanate ceramics. Both materials have high ionic mobilities at room temperature and this is reflected in their static ⁷Li powder patterns. In the case of the phosphate based ceramic, a narrow Lorentzian peak is observed above 300 K, which narrows further with increasing temperature. The accompanying quadrupolar structure, with C_Q (quadrupolar coupling constant) ~ 40 kHz, suggests that the lithium ions are hopping rapidly between equivalent, high electric field gradient sites. The ²⁷Al and ³¹P magic angle spinning (MAS) spectra reveal an asymmetric phosphorus peak and two distinct aluminium resonances. The room temperature powder pattern of Li_0.33La_0.57TiO₃ shows a dipolar broadened peak which narrows quite suddenly at 310 K revealing quadrupolar satellites with C_Q ~ 900 Hz. A second lithium site is also observed in this material, as indicated by a further, weaker quadrupolar structure (C_Q ~ 40 kHz).

Biomimetic modification of porous TiNbZr alloy scaffold for bone tissue engineering

Porous titanium (Ti) and Ti alloys are important scaffold materials for bone tissue engineering. In the present study, a new type of porous Ti alloy scaffold with biocompatible alloying elements, that is, niobium (Nb) and zirconium (Zr), was prepared by a space-holder sintering method. This porous TiNbZr scaffold with a porosity of 69% exhibits a mechanical strength of 67MPa and an elastic modulus of 3.9GPa, resembling the mechanical properties of cortical bone. To improve the osteoconductivity, a calcium phosphate (Ca/P) coating was applied to the surface of the scaffold using a biomimetic method. The biocompatibility of the porous TiNbZr alloy scaffold before and after the biomimetic modification was assessed using the SaOS2 osteoblast–like cells. Cell culture results indicated that the porous TiNbZr scaffold is more favorable for cell adhesion and proliferation than its solid counterpart. By applying a Ca/P coating, the cell proliferation rate on the Ca/P-coated scaffold was significantly improved. The results suggest that high-strength porous TiNbZr scaffolds with an appropriate osteoconductive coating could be potentially used for bone tissue engineering application.

Porous shape memory alloy scaffolds for biomedical applications : a review

The interest in using porous shape memory alloy (SMA) scaffolds as implant materials has been growing in recent years due to the combination of their unique mechanical and functional properties, i.e. shape memory effect and superelasticity, low elastic modulus combined with new bone tissue ingrowth ability and vasculariszation. These attractive properties are of great benefit to the healing process for implant applications. This paper reviews current state-of-the art on the processing, porous characteristics and mechanical properties of porous SMAs for biomedical applications, with special focus on the most widely used SMA nickel-titanium (NiTi), including (i) microstructural features, mechanical and functional properties of NiTi SMAs; (ii) main processing methods for the fabrication of porous NiTi SMAs and their mechanical properties and (iii) new-generation Ni-free, biocompatible porous SMA scaffolds.

Ingrowth of human mesenchymal stem cells into porous silk particle reinforced silk composite scaffolds : an in vitro study

Silk fibroin protein is biodegradable and biocompatible, exhibiting excellent mechanical properties for various biomedical applications. However, porous three-dimensional (3-D) silk fibroin scaffolds, or silk sponges, usually fall short in matching the initial mechanical requirements for bone tissue engineering. In the present study, silk sponge matrices were reinforced with silk microparticles to generate protein-protein composite scaffolds with desirable mechanical properties for in vitro osteogenic tissue formation. It was found that increasing the silk microparticle loading led to a substantial increase in the scaffold compressive modulus from 0.3 MPa (non-reinforced) to 1.9 MPa for 1:2 (matrix:particle) reinforcement loading by dry mass. Biochemical, gene expression, and histological assays were employed to study the possible effects of increasing composite scaffold stiffness, due to microparticle reinforcement, on in vitro osteogenic differentiation of human mesenchymal stem cells (hMSCs). Increasing silk microparticle loading increased the osteogenic capability of hMSCs in the presence of bone morphogenic protein-2 (BMP-2) and other osteogenic factors in static culture for up to 6 weeks. The calcium adsorption increased dramatically with increasing loading, as observed from biochemical assays, histological staining, and microcomputer tomography (μCT) analysis. Specifically, calcium content in the scaffolds increased by 0.57, 0.71, and 1.27 mg (per μg of DNA) from 3 to 6 weeks for matrix to particle dry mass loading ratios of 1:0, 1:1, and 1:2, respectively. In addition, μCT imaging revealed that at 6 weeks, bone volume fraction increased from 0.78% for non-reinforced to 7.1% and 6.7% for 1:1 and 1:2 loading, respectively. Our results support the hypothesis that scaffold stiffness may strongly influence the 3-D in vitro differentiation capabilities of hMSCs, providing a means to improve osteogenic outcomes.

Three-dimensional porous polymer scaffolds for tissue engineering application

This thesis investigates three-dimensional porous polymer blend scaffolds fabricated using supercritical carbon dioxide combined with solvent etching. These scaffolds with improved pore structures and interconnectivity can be used in regeneration medicine and tissue engineering application.

Biomimetic porous titanium scaffolds for orthopaedic and dental applications

The development of artificial organs and implants for replacement of injured and diseased hard tissues such as bones, teeth and joints is highly desired in orthopedic surgery. Orthopedic prostheses have shown an enormous success in restoring the function and offering high quality of life to millions of individuals each year. Therefore, it is pertinent for an engineer to set out new approaches to restore the normal function of impaired hard tissues.

Over the last few decades, a large number of metals and applied materials have been developed with significant improvement in various properties in a wide range of medical applications. However, the traditional metallic bone implants are dense and often suffer from the problems of adverse reaction, biomechanical mismatch and lack of adequate space for new bone tissue to grow into the implant. Scientific advancements have been made to fabricate porous scaffolds that mimic the architecture and mechanical properties of natural bone. The porous structure provides necessary framework for the bone cells to grow into the pores and integrate with host tissue, known as osteointegration. The appropriate mechanical properties, in particular, the low elastic modulus mimicking that of bone may minimize or eliminate the stress-shielding problem. Another important approach is to develop biocompatible and corrosion resistant metallic materials to diminish or avoid adverse body reaction. Although numerous types of materials can be involved in this fast developing field, some of them are more widely used in medical applications. Amongst them, titanium and some of its alloys provide many advantages such as excellent biocompatibility, high strength-to-weight ratio, lower elastic modulus, and superior corrosion resistance, required for dental and orthopedic implants. Alloying elements, i.e. Zr, Nb, Ta, Sn, Mo and Si, would lead to superior improvement in properties of titanium for biomedical applications.

New processes have recently been developed to synthesize biomimetic porous titanium scaffolds for bone replacement through powder metallurgy. In particular, the space holder sintering method is capable of adjusting the pore shape, the porosity, and the pore size distribution, notably within the range of 200 to 500 m as required for osteoconductive applications. The present chapter provides a review on the characteristics of porous metal scaffolds used as bone replacement as well as fabrication processes of porous titanium (Ti) scaffolds through a space holder sintering method. Finally, surface modification of the resultant porous Ti scaffolds through a biomimetic chemical technique is reviewed, in order to ensure that the surfaces of the scaffolds fulfill the requirements for biomedical applications.

Structure and capacitive properties of porous nanocrystalline VN produced by NH3 reduction of V2O5

Vanadium nitride (VN) is currently one of the most promising materials for electrodes of supercapacitors. The structure and electrochemical properties of VN synthesized by temperature-programmed NH₃ reduction of V₂O₅ are analyzed in this paper. Vanadium nitride produced via this route has distinctive structural characteristics. VN mimics the shape of the initial V₂O₅ precursor indicating a pronounced direct attachment of nitride grains. The particles have domains of grains with a preferential orientation (texture). The large volume of pores in VN is represented by the range of 15−110 nm. VN demonstrates capacitive properties in three different types of aqueous electrolytes, 1 M KOH, 1 M H₂SO₄, and 3 M NaCl. The material has an acceptable rate capability in all electrolytes, showing about 80% of its maximal capacitance at a current load of 1 A/g in galvanostatic charging/discharging experiments. The capacitance of 186 F/g is observed in 1 M KOH electrolyte at 1 A/g. The previously reported negative effect of material loading on the capacitance is significantly suppressed. The observed electrochemical characteristics related to the application of this material in supercapacitors can be correlated with the crystalline structure of the nitride and the composition of its surface layer.