Biodegradation of pentachlorophenol in a membrane bioreactor

Pentachlorophenol (PCP) is a toxic chemical, often used in the formulation of pesticide, herbicide, anti fungal agent, bactericide and wood preservative. This study is aimed at evaluating the potential of membrane bioreactor (MBR) to treat PCP contaminated wastewater. Synthetic wastewater with COD of 600 mg/L was fed into the MBR at varied PCP loading rate of 12–40 mg/m3/d. A PCP removal rate of 99% and a COD removal rate of 95% were achieved at a hydraulic retention time of 12 hs and a mixed liquor suspended solids (MLSS) concentration of 10,000 mg/L. When sodium pentachlorophenol (NaPCP), which has higher solubility in water, was used in the second phase of the study, at loading rates varying from 20 to 200 mg/m3·d, the removal rate of NaPCP was higher than 99% and the removal rate of COD was more than 96%. It was also found that at higher biomass concentrations, biosorption played an important role besides the biodegradation process. Batch experiments conducted in this study revealed that the sorption capacity to be 0.63 (mg PCP/g biomass) and occurred rapidly within 60 min. This phenomenon could enhance the PCP degradation through increased contact between microorganism and PCP. Further, the membrane resistance was low (trans-membrane pressure of 14 kPa) even after more than 100 ds of operation. In addition, the toxic level of PCP in the influent could have induced the microorganisms to secrete more extra-cellular polymeric substances (EPS) for their protection, which in turn must have increased the viscosity of the mixed liquor.

Control of biodegradation of a Mg alloy in simulated body fluid

Mg alloy AZ31 is an attractive candidate for coronary artery stents, as it possesses excellent biocompatibility in human body and good mechanical properties. However, AZ31 magnesium alloys generally have poor corrosion resistance in the body environment. This paper reports on the early stages of an investigation into the corrosion mechanism and the morphology of corrosion of AZ31 in simulated body fluid (SBF). The investigation will also consider ways of improving corrosion resistance of this alloy in SBF through the use of ionic liquids. The results to date have shown that AZ31 suffers severe localized pitting corrosion in SBF. The pits mainly develop adjacent to the Al-Mn intermetallic second phase in the α matrix. Energy Dispersive X-Ray Spectroscopy results revealed the presence of Mg, O, Ca, and P in the layer of corrosion product. Treatment of the AZ31 alloy prior to corrosion testing in SBF with the ionic liquid trimethyl (butyl) phosphonium diphenyl phosphate (P1444DPP) produced some increase in the corrosion resistance of the alloy.

π-Selective stationary phases: (III) Influence of the propyl phenyl ligand density on the aromatic and methylene selectivity of aromatic compounds in reversed phase liquid chromatography

The retention characteristics of phenyl type stationary phases for reversed phase high performance liquid chromatography are still largely unknown. This paper explores the retention process of these types of stationary phases by examining the retention behaviour of linear PAHs and n-alkylbenzenes on a series of propyl phenyl stationary phases that have changes in their ligand density (1.23, 1.31, 1.97, 2.50 μmol m⁻²). The aromatic and methylene selectivities increased with increasing ligand density until a point where a plateau was observed, overall the propyl phenyl phases had a higher degree of aromatic selectivity than methylene selectivity indicating that these columns are suitable for separations involving aromatic compounds. Also, retention characteristics relating to the size of the solute molecule were observed to be influenced by the ligand density. It is likely that the changing retention characteristics are caused by the different topologies of the stationary phases at different ligand densities. At high ligand densities, the partition coefficient became constant.

Polycyclic aromatic hydrocarbon emission loads and profiles from the burning of locally grown wood species in Victoria, Australia - Some pilot project results

A testing facility for combustion of biomass and sampling of emissions has been established at Deakin University. In this pilot project using this facility, four kinds of locally grown wood species were burned and the particle emissions sampled and analysed for Polycyclic Aromatic Hydrocarbons (PAHs). The selected wood species covering pine, red gum, yellow box and sugar gum, are the most popular domestic fuel wood in Australia. Particulate matter emissions from burning of each load of wood were sampled from the flue using a standard stack emission sampling train. The particle-laden filters were extracted and the .extract analysed to determine PAH concentrations by Gas Chromatographyl Mass Spectrometer (Gc/MS). The sampling was conducted under two different burning conditions with the air inlet of the combustion chamber fully open and with it half open. A suite of 15 PAHs, ranging from naphthalene (C IOHB) to dibenzolahlanthracene (C12H14), were selected for analysis. PAH profiles for the four wood species, under the different burning regimes, have been generated. Some preliminary emission factors for the different wood species have been derived as microgram of summed PAHs (rPAHs) emittedlkilogram of wood burned. Total Particulate Matter (TPM) emission factors were also obtained from gravimetric measurement of the sample filter before and after the combustion. Based on these emission factors, pine displayed the highest level of rPAHs emitted from the combustion of the four wood species, with sugar gum showing the lowest level of rPAHs emission. Emission factors associated with the slow burning condition clearly showed higher l:PAH levels compared to the faster burning condition. During the faster burning condition, red gum and pine show a higher percentage of rPAH to TPM than sugar gum or yellow box. Under the slower burning. the l:PAHlTPM ratio in every case was greater.

Degradation of phenanthrene and pyrene in soil slurry reactors with immobilized bacteria Zoogloea sp.

The environmental fate of polycyclic aromatic hydrocarbons (PAHs) in soils is motivated by their wide distribution, high persistence, and potentially deleterious effect on human health. Polycyclic aromatic hydrocarbons constitute the largest group of environmental contaminants released in the environment. Therefore, the potential biodegradation of these compounds is of vital importance. A biocarrier suitable for the colonization by micro-organisms for the purpose of purifying soil contaminated by polycyclic aromatic hydrocarbons was developed. The optimized composition of the biocarrier was polyvinyl alcohol (PVA) 10%, sodium alginate (SA) 0.5%, and powdered activated carbon (PAC) 5%. There was no observable cytotoxicity of biocarriers on immobilized cells and a viable cell population of 1.86 × 10¹⁰ g^–1 was maintained for immobilized bacterium. Biocarriers made from chemical methods had a higher biodegradation but lower mechanical strengths. Immobilized bacterium Zoogloea sp. had an ideal capability of biodegradation for phenanthrene and pyrene over a relative wide concentration range. The study results showed that the biodegradation of phenanthrene and pyrene reached 87.0 and 75.4%, respectively, by using the optimal immobilized method of Zoogloea sp. cultivated in a sterilized soil. Immobilized Zoogloea sp. was found to be effective for biodegrading the soil contaminated with phenanthrene and pyrene. Even in "natural" (unsterilized) soil, the biodegradation of phenanthrene and pyrene using immobilized Zoogloea sp. reached 85.0 and 67.1%, respectively, after 168 h of cultivation, more than twice that achieved if the cells were not immobilized on the biocarrier. Therefore, the immobilization technology enhanced the competitive ability of introduced micro-organisms and represents an effective method for the biotreatment of soil contaminated with phenanthrene and pyrene.

Characterising vehicle emissions from the burning of biodiesel made from vegetable oil

Biodiesel manufactured from canola oil was blended with diesel and used as fuel in two diesel vehicles. This study aimed to test the emissions of diesel engines using blends of 100%, 80%, 60%, 40% , 20% biodiesel and 100% petroleum diesel, and characterise the particulate matter and gaseous emissions, with particular attention to levels of polycyclic aromatic hydrocarbons (PAHs) which are harmful to humans. A real time dust monitor was also used to monitor the continuous dust emissions during the entire testing cycle. The ECE(Euro 2) drive cycle was used for all emission tests. It was found that the particle concentration was up to 33% less when the engine burnt 100% biodiesel, compared to 100% diesel. Particle emission reduced with increased percentages of biodiesel in the fuel blends. Reductions of NOx, HC and CO were limited to about 10% when biodiesel was burned. Levels of CO2 emissions from the use of biodiesel and diesel were similar. Eighteen EPA priority PAHs were targeted, with only 6 species detected in the gaseous phase from the samples . 9 PAHs were detected in particulate phases at much lower levels than gaseous PAHs. Some marked reductions were observed for less toxic gaseous PAHs such as naphthalene when burning 100% biodiesel, but the particulate PAH emissions, which have more implications to adverse health effects, were virtually unchanged and did not show a statistically significant reduction. These findings are useful to gain an understanding of the emissions and environmental impacts of biodiesel.

Preconcentration of phenanthrene from aqueous solution by a slightly hydrophobic nonionic surfactant

The preconcentration of phenanthrene from aqueous solution was discussed. The study was carried out by using a slightly hydrophobic nonionic surfactant. The slightly hydrophobic surfactant, at proper condition enhanced the performance of the surfactant-based extraction process on polycyclic aromatic hydrocarbons (PAH). The results show that the increasing the temperature difference enhanced the preconcentration factors prominently but only slightly the recovery efficiency.

Effects of π-π interactions on the separation of PAHs on phenyl-type stationary phases

Phenyl‐type stationary phase surfaces are useful for the separation of highly aromatic compounds because of the extensive intermolecular forces between the π‐electron systems. For this reason, we studied the retention behaviour and selectivity of polycyclic aromatic hydrocarbons (PAHs) on Synergi polar‐RP and Cosmosil 5PBB chromatography columns using methanol/water, acetonitrile/water, benzene spiked (0.5%) methanol/water, and benzene spiked (0.5%) acetonitrile/water mobile phases. These four solvent systems were employed because π‐π. interactions between the aromatic solute (i.e., PAH) and the aromatic stationary phase should be inhibited in mobile phases that are also π electron rich, and hence a competitor for the analyte. Our results showed that the acetonitrile mobile phases were substantially stronger eluents than the methanol mobile phases, which was consistent with the premise that retention of aromatic compounds is sensitive to π‐π. interactions. Aside from changes in absolute retention, selectivity of the PAHs was also generally greater in methanol rather than acetonitrile mobile phases because the methanol did not attenuate the π‐π. bonding interactions between the PAH and the stationary phase; but, despite this, the retention behaviour of the Synergi polar‐RP column was similar to that observed on C₁₈ columns. The excessive retention times of the Cosmosil 5PBB column were decreased dramatically when acetonitrile was used as the mobile phase; however, selectivity between structural isomers was lost.

Investigating retention characteristics of a mixed-mode stationary phase and the enhancement of monolith selectivity for high-performance liquid chromatography

The synthesis and chromatographic behavior of an analytical size mixed-mode bonded silica monolith was investigated. The monolith was functionalized by an in situ modification process of a bare silica rod with chloro(3-cyanopropyl)dimethyl silane and chlorodimethyl propyl phenyl silane solutions. These ligands were selected in order to combine both resonance and nonresonance π-type bonding within a single separation environment. Selectivity studies were undertaken using n-alkyl benzenes and polycyclic aromatic hydrocarbons in aqueous methanol and acetonitrile mobile phases to assess the methylene and aromatic selectivities of the column. The results fit with the linear solvent strength theory suggesting excellent selectivity of the column was achieved. Comparison studies were performed on monolithic columns that were functionalized separately with cyano and phenyl ligands, suggesting highly conjugated molecules were able to successfully exploit both of the π-type selectivities afforded by the two different ligands on the mixed-mode column.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

Removal of VOCs by photocatalysis process using adsorption enhanced TiO2–SiO2 catalyst

Volatile organic compounds (VOCs) exist widely in both the indoor and outdoor environment. The main contributing sources of VOCs are motor vehicle exhaust and solvent utilization. Some VOCs are toxic and carcinogenic to human health, such as benzene. In this study, TiO₂–SiO₂ based photocatalysts were synthesized using the sol–gel method, with high surface areas of 274.1–421.1 m²/g obtained. Two types of pellets were used as catalysts in a fixed-bed reactor installed with a UV black light lamp. Experiments were conducted to compare their efficiencies in degrading the VOCs. Toluene was used as the VOC indicator. When the toluene laden gas stream passed through the photocatalytic reactor, the removal efficiencies were determined using a FTIR multi-gas analyser, which was connected to the outlet of the reactor to analyse the toluene concentrations. As the TiO₂–SiO₂ pellets used have a high adsorption capacity, they had dual functions as a photocatalyst and adsorbent in the hybrid photocatalysis and adsorption system. The experiments demonstrated that the porous photocatalyst with very high adsorptive capacity enhanced the subsequent photocatalysis reactions and lead to a positive synergistic effect. The catalyst can be self-regenerated by photocatalytic oxidation of the adsorbed VOCs. When the UV irradiation and feeding gas is continuous, a destruction efficiency of about 25% was achieved over a period of 20 h. Once the system was designed and operated into adsorption/regeneration mode, a higher removal efficiency of about 55% was maintained. It was found that the catalyst pellets with a higher surface area (421 m²/g) achieved higher conversion efficiency (100%) for a longer period than those with a lower surface area. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer, finding that the main components of the treated gas stream leaving the reactor, along with untreated toluene, were CO₂ and water. The suspected intermediates of aliphatic hydrocarbons and CO were found in minimal amounts or were non detectable. The kinetic rate constants were calculated from the experimental results, it appeared that the stronger adsorption capacity, i.e. larger specific surface area, the higher conversion efficiency would be achieved.

Annetocin and TCTP expressions in the earthworm Eisenia fetida exposed to PAHs in artificial soil

The toxicity of sublethal polycyclic aromatic hydrocarbons (PAHs) levels in soils was assessed by testing their impact on expression of annetocin, a reproduction regulating gene, and translationally controlled tumor protein (TCTP), a tumorigenic response gene, in the earthworm Eisenia fetida cultured in artificial soil spiked with, phenanthrene (Phe), pyrene (Pyr), fluoranthene (Flu), or benzo(a)pyrene (Bap). Annetocin and TCTP were both up-regulated by 0.1 and 1.0 mg kg−1 benzo(a)pyrene and TCTP was down-regulated by 10.0 mg kg−1 phenanthrene. Weight loss and cocoon production of the worms were also analyzed. Only 10.0 mg kg−1 phenanthrene impacted earthworm weight loss significantly and no significant differences on cocoon production were observed. Our study indicated that the potential ecotoxicity of sublethal PAHs in soil should not be neglected and mRNA transcription level in earthworms was a more sensitive indicator of PAHs exposure than traditional indexes using cocoon production as endpoints and/or using the whole-organism as the test materials.

植物CytP450和抗氧化酶对土壤低浓度菲、芘胁迫的响应

Wheat (Triticum aestivum) was chosen to analyze the effect of two polycyclic aromatic hydrocarbons (PAHs), Phenanthrene (PHE) and Pyrene (PY) in brown meadow soil at low concentrations. The effects of PHE and PY were determined by analyzing the changes in activity of Cytochrome P450 (CytP450) and antioxidant enzymes superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT). Results indicated that both PHE and PY caused changes in activity of CytP450 and the antioxidant enzymes, SOD, POD and CAT. CytP450 activity was significantly stimulated with 1 mg kg-1 of both PHE and PY individually and significantly inhibited with 4 mg kg-1, which showed that pollution stress of PHE or PY can damage the metabolism and detoxification systems of plants. Moreover, as PHE and PY combined at 1 mg kg-1, CytP450 was increased significantly more than when PHE and PY were applied individually, which illustrates obvious synergistic effects. No significant variation were found in activity of SOD in response to individual exposure of PHE or PY in soil, but SOD activity decreased slightly in response to a combined PHE and PY exposure. Great decrease variation was found in CAT and POD activity in response to individual exposure of PHE or PY in soil. No enhanced toxic effects were shown by POD in response to a PHE and PY combined exposure, however CAT showed increased inhibition. From the aspects of metabolism and detoxification as well as antioxidant enzyme activity, our study has provided experimental basis for the pollution diagnosis of PAHs in soils at low concentrations.

Phenyl-type and C1 stationary phases for environmentally friendlier chromatography

C1 and phenyl-type stationary phases were assessed in terms of their environmental impact on separations using as test solutes polycyclic aromatic hydrocarbons. Methanol (MeOH) and acetonitrile (ACN) mobile-phase gradients were employed. These stationary phases were examined to determine if different physical and chemical properties possessed by these surfaces decreased the organic solvent consumption, and yet maintained peak capacity. The cumulative energy demand (CED) was used to gauge the environmental impact of the separations. The separation of the polycyclic aromatic hydrocarbon test mixture using current methodologies (i.e. a C18/ACN combination) had a CED of 1.13 MJ-eq, and a peak capacity of 27 peaks (resolving 7 of 12 peak pairs with R_s>1). In comparison, a butyl phenyl stationary phase with a methanol mobile phase had a peak capacity of 26, but with a CED of 0.670 MJ-eq. Monolithic columns containing C18 and C1 phases were also tested. A monolithic C18 column with MeOH had the lowest CED at 0.675 MJ-eq, a peak capacity of 28 peaks and good resolving power (resolving ten peak pairs with R_s>1), suggesting that this is a viable option with respect to reducing environmental impact for these types of analyses.