Testing of combined heating systems for small houses: Improved procedures for whole system test methods : Deliverable 2.3

Dynamic system test methods for heating systems were developed and applied by the institutes SERC and SP from Sweden, INES from France and SPF from Switzerland already before the MacSheep project started. These test methods followed the same principle: a complete heating system – including heat generators, storage, control etc., is installed on the test rig; the test rig software and hardware simulates and emulates the heat load for space heating and domestic hot water of a single family house, while the unit under test has to act autonomously to cover the heat demand during a representative test cycle. Within the work package 2 of the MacSheep project these similar – but different – test methods were harmonized and improved. The work undertaken includes:  • Harmonization of the physical boundaries of the unit under test. • Harmonization of the boundary conditions of climate and load. • Definition of an approach to reach identical space heat load in combination with an autonomous control of the space heat distribution by the unit under test. • Derivation and validation of new six day and a twelve day test profiles for direct extrapolation of test results.   The new harmonized test method combines the advantages of the different methods that existed before the MacSheep project. The new method is a benchmark test, which means that the load for space heating and domestic hot water preparation will be identical for all tested systems, and that the result is representative for the performance of the system over a whole year. Thus, no modelling and simulation of the tested system is needed in order to obtain the benchmark results for a yearly cycle. The method is thus also applicable to products for which simulation models are not available yet. Some of the advantages of the new whole system test method and performance rating compared to the testing and energy rating of single components are:  • Interaction between the different components of a heating system, e.g. storage, solar collector circuit, heat pump, control, etc. are included and evaluated in this test. • Dynamic effects are included and influence the result just as they influence the annual performance in the field. • Heat losses are influencing the results in a more realistic way, since they are evaluated under "real installed" and representative part-load conditions rather than under single component steady state conditions.   The described method is also suited for the development process of new systems, where it replaces time-consuming and costly field testing with the advantage of a higher accuracy of the measured data (compared to the typically used measurement equipment in field tests) and identical, thus comparable boundary conditions. Thus, the method can be used for system optimization in the test bench under realistic operative conditions, i.e. under relevant operating environment in the lab.   This report describes the physical boundaries of the tested systems, as well as the test procedures and the requirements for both the unit under test and the test facility. The new six day and twelve day test profiles are also described as are the validation results.

Mechanical and tribological properties of PVD-coated cemented carbide as evaluated by a new multi-pass scratch testing method

A new test method based on multipass scratch testing has been developed for evaluating the mechanical and tribological properties of thin, hard coatings. The proposed test method uses a pin-on-disc tribometer and during testing a Rockwell C diamond stylus is used as the “pin” and loaded against the rotating coated sample. The influence of normal load on the number of cycles to coating damage is investigated and the resulting coating damage mechanisms are evaluated by posttest scanning electron microscopy. The present study presents the test method by evaluating the performance of Ti0.86Si0.14N, Ti0.34Al0.66N, and (Al0.7Cr0.3)2O3 coatings deposited by cathodic arc evaporation on cemented carbide inserts. The results show that the test method is quick, simple, and reproducible and can preferably be used to obtain relevant data concerning the fatigue, wear, chipping, and spalling characteristics of different coating-substrate composites. The test method can be used as a virtually nondestructive test and, for example, be used to evaluate the fatigue and wear resistance as well as the cohesive and adhesive interfacial strength of coated cemented carbide inserts prior to cutting tests.

Utvärdering av mätmetoder för att fastställa lackmängden vid offsettryckning on-line

This project has been made in cooperation with Stora Enso Research Centre Falun (Research). Thebackground of the project is that Research has customers who demand a method to measure the quantityof varnish online in offset printing. The aim with the project is to investigate if any test method correlateswith the quantity of varnish and to improve the understanding of the variables in the varnishingunit. The goal with the project is to develop a functional method. Two printing trials have beenperformed. The aim with the first trial was to investigate how different factors in the printer influencedthe quantity of varnish using reduced factoranalysis. The aim of the second trial was to analyse onlya reduced numbers of factors in the varnishing unit. The methods that were used to measure the varnishingquantity are weighing, IR-analysis, gloss, whiteness and brightness. Results from the projectshow that the weighing method does not work in this study due to basis weight variations of the sheets.The results from weighing did not agree with the results from the other methods. On the other handthere is a strong correation between the IR- and the glossmethods.

Print quality study of newsprint : Further development of the laboratoryoffset press at PAPRO

A laboratory offset press has been developed over the last five years at PAPRO for testing print qualityon newsprint, as at present, there is no good way for the mills to test this issue. In this project a comparisonhas been made between a laboratory offset press and a commercial press to see if the laboratoryoffset press can be used as a reliable test method or if a further development is needed.To evaluate the method, similar papers have been printed in both presses and compared using imageanalysis techniques. All together eighteen samples were tested which is enough to give comparableresults. The print quality showed a high variation, the values from the laboratory offset press and thecommercial press were not following the same trends. At present time the laboratory offset press needsome further development before it can be used as a reliable test method for halftone prints. Even sosome conclusions were made.The newsprint that has been used came from Norske Skog Tasman Mill (Kawerau), since the otheraim of this project was to do a repeatability study of their three existing paper machines to distinguishpossible differences in the production. The paper samples were taken from each paper machine on sixdifferent dates to give a representative result. This also gave the opportunity to compare the machinesbetween themselves. Comparison between the machines shows that the wire side gives a better andmore even result than the topside on the prints from the laboratory offset press. According to the resultfrom the commercial press the wire side shows a higher degree of variability. Samples from papermachine 2 and 3 were less variable and had the lowest standard deviation of grey level for solid areas.This suggests that newsprints from PM 2 and PM 3 give a more even print quality with a better inkcoverage.

En analys av testprocesser med TMap som testmetod

Today there are many system development projects that break both budget and time plan. Often this depends on defects in the information systems that could have been prevented. The cost of test can in some cases be as high as 50 % of the projects total cost and it's at the same time an important part of development. Test as such has moved its focus from the software it self and its faults to a wider perspective on whole infrastructures of information systems where assure a good quality is important. Sogeti in the Netherlands have developed a test method called TMap (Test Management approach) that can be used for structured testing of information systems. TMap haven't been used as much as desired in the office in Borlänge. Because Microsoft is releasing a new version of their platform Visual Studio Team System (VSTS 2010) some colleges at Sogeti in the Netherlands are about to develop a template that can support the use of TMap in VSTS 2010. When we write this the template is still in development. The goal for Sogeti was to find out the differences between the test functionality in VSTS 2008 and 2010. By using the purpose with this essay, which was to analyze the test process in VSTS 2008 with TMap against the test process in VSTS 2010 together with the template we got much help to achieve the goal. The analysis was done with four different aspects: The TPI and TMMi models, problem and strength analyses and a few question formulations. The TPI and TMMi models where used to analyses and evaluate the test process. The analysis showed that there were differences between the both test processes. VSTS 2010 together with the template gave a better support to use TMap and perform test. In VSTS 2010 the test tool Camano is connected to TFS and the tool is also to make the execution and logging of tests easier. This leads to a test process that is easier to handle and has a better support for TMap.

Provningsmetod för integrerade sol-biosystem : Årsverkningsgrad genom korttidsmätning

Test method for integrated solar- biomass systems - Long term prediction trough short term measurementsSP Technical Research Institute of Sweden and SERC, Dalarna University have in cooperation developed a test method for integrated solar and biomass systems. The test method is performed under six days including two summer days, two winter days and two spring/autumn days true to real weather conditions and loads for a single family house. The aim of the test method is to get information about a Combisystem’s annual performance and operation throughout a short term test. Seven different solar Combisystems have been tested within the project together with a pellet boiler without solar collectors. In addition to that a comparative testing has been performed at the two laboratories at SP and at SERC on the same Combisystem. The test method developed within the project has been proved to withstand the aim of the project, which is to be able to compare the performance between the systems. The test method is also suitable for identification of possible operation problems so they can be taken care of and consequently improves the system.The project and the system testing reveal that it is in general favorable to combine biomass pellets with solar heating. Pellet boilers has normally a low performance during the summer period but combined with a solar collector the boiler can be switch off during this period. There are however big differences in performance between the tested. The efficiency of the pellet boiler is highly dependent of the operating conditions and elements like heat losses from the system, system configuration and control strategy have great influence of the performance of the system and the emissions. On the other hand, the performance and the size of the solar collectors have a minor effect on the overall system performance. There is obviously a big potential for improvement of the system´s performance and the developed test method is an essential way to implement this perfection.

Thermal Performance of a Solarus CPC-Thermal Collector

The  aim  of  this  master  thesis  is  an  investigation  of  the  thermal  performance  of  a  thermal compound parabolic concentrating (CPC) collector from Solarus. The collector consists of two troughs with absorbers which are coated with different types of paint with  unknown  properties.  The  lower  and  upper  trough  of  the  collector  have  been  tested individually. In  order  to  accomplish  the  performance  of  the  two  collectors,  a  thorough  literature  study  in  the  fields  of  CPC  technology,  various  test  methods,  test  standards  for  solar thermal  collectors  as  well  as  the  latest  articles  relating  on  the  subject  were  carried  out. In addition, the set‐up of the thermal test rig was part of the thesis as well. The thermal  performance  was  tested  according  to  the  steady  state  test  method  as  described in the European standard 12975‐2. Furthermore, the thermal performance of  a  conventional  flat  plate  collector  was  carried  out  for  verification  of  the  test  method. The  CPC‐Thermal  collector  from  Solarus  was  tested  in  2013  and  the  results  showed  four  times  higher  values  of  the  heat  loss  coefficient  UL (8.4  W/m²K)  than  what  has been reported for a commercial collector from Solarus. This value was assumed to be too large and it was assumed that the large value was a result of the test method used that time. Therefore, another aim was the comparison of the results achieved in this work with the results from the tests performed in 2013. The results of the thermal performance showed that the optical efficiency of the lower trough of the CPC‐T collector is 77±5% and the corresponding heat loss coefficient UL 4.84±0.20  W/m²K.  The  upper  trough  achieved  an  optical  efficiency  of  75±6  %  and  a  heat loss coefficient UL of 6.45±0.27 W/m²K. The results of the heat loss coefficients  are  valid  for  temperature  intervals  between  20°C  and  80°C.  The  different  absorber paintings have a significant impact on the results, the lower trough performs overall better.  The  results  achieved  in  this  thesis  show  lower  heat  loss  coefficients UL and higher optical efficiencies compared to the results from 2013. 

Företags potentiella manipulation av tillväxttakt i goodwillnedskrivningstestet : En kvantitativ studie av svenska och finska börsnoterade företag

Bakgrund och problem: I och med den nya standarden IAS 36 ska företagen göra uppskattningar angående den långsiktiga tillväxttakten i goodwillnedskrivningstestet. Detta innebär en möjlighet att manipulera tillväxttakten för att på så vis undvika eller framkalla nedskrivning av goodwill. Problemformulering: Hur påverkar utvalda variabler företags potentiella manipulation av angiven tillväxttakt? Syfte: Syftet med studien är att bidra med förklaringar till vad som påverkar att företag redovisar för höga respektive för låga tillväxttakter i goodwillnedskrivningstestet. Metod: Denna studie bygger på en kvantitativ metod där urvalet består av samtliga svenska och finska börsnoterade företag med redovisad goodwill. Utifrån existerade kunskap formuleras fyra hypoteser som testas mot empirin. Resultat och slutsats: Resultatet av denna studie visar inga signifikanta samband mellan den beroende variabeln manipulation och de oberoende variablerna storlek, skuldsättningsgrad, bransch och redovisningstillsyn. Den deskriptiva statistiken visar att i stort sett hälften av företagen manipulerar tillväxttakten.

Automatiserade regressionstester avseende arbetsflöden och behörigheter i ProjectWise. : En fallstudie om ProjectWise på Trafikverket

Test av mjukvara görs i syfte att se ifall systemet uppfyller specificerade krav samt för att hitta fel. Det är en viktig del i systemutveckling och involverar bland annat regressionstestning. Regressionstester utförs för att säkerställa att en ändring i systemet inte medför att andra delar i systemet påverkas negativt. Dokumenthanteringssystem hanterar ofta känslig data hos organisationer vilket ställer höga krav på säkerheten. Behörigheter i system måste därför testas noggrant för att säkerställa att data inte hamnar i fel händer. Dokumenthanteringssystem gör det möjligt för flera organisationer att samla sina resurser och kunskaper för att nå gemensamma mål. Gemensamma arbetsprocesser stöds med hjälp av arbetsflöden som innehåller ett antal olika tillstånd. Vid dessa olika tillstånd gäller olika behörigheter. När en behörighet ändras krävs regressionstester för att försäkra att ändringen inte har gjort inverkan på andra behörigheter. Denna studie har utförts som en kvalitativ fallstudie vars syfte var att beskriva utmaningar med regressionstestning av roller och behörigheter i arbetsflöden för dokument i dokumenthanteringssystem. Genom intervjuer och en observation så framkom det att stora utmaningar med dessa tester är att arbetsflödens tillstånd följer en förutbestämd sekvens. För att fullfölja denna sekvens så involveras en enorm mängd behörigheter som måste testas. Det ger ett mycket omfattande testarbete avseende bland annat tid och kostnad. Studien har riktat sig mot dokumenthanteringssystemet ProjectWise som förvaltas av Trafikverket. Beslutsunderlag togs fram för en teknisk lösning för automatiserad regressionstestning av roller och behörigheter i arbetsflöden åt ProjectWise. Utifrån en kravinsamling tillhandahölls beslutsunderlag som involverade Team Foundation Server (TFS), Coded UI och en nyckelordsdriven testmetod som en teknisk lösning. Slutligen jämfördes vilka skillnader den tekniska lösningen kan utgöra mot manuell testning. Utifrån litteratur, dokumentstudie och förstahandserfarenheter visade sig testautomatisering kunna utgöra skillnader inom ett antal identifierade problemområden, bland annat tid och kostnad.

Evaluation of surface treatment techniques for polypropylene andimplementation of a method for testing ink adhesion

If a plastic material is used as a print bearer there are a need of a special surface treatment to get agod and durable printing. The most used surface treatment technique for the moment is coronatreatment. This kind of treatment has unfortunately showed not to be so durable in the long term.Plasma treatment which in this case uses different kind of gases in the treatment of polypropyleneis shown as a more effective treatment in this project. When the plasma treated surface has beenprinted is the good quality last much longer and the adhesion between the ink and the surface isremained. To test this adhesion is for the moment a standard used (ASTM D3359). This standardhas appeared unstable and dependent at many different factors, which gives a big variation in thetest results. Because of this has new test methods been carried out to give a more even and morereliable result in the test of the adhesion.

Simultaneous prediction of symptom severity and cause in data from a test battery for Parkinson patients, using machine learning methods

The main purpose of this thesis project is to prediction of symptom severity and cause in data from test battery of the Parkinson’s disease patient, which is based on data mining. The collection of the data is from test battery on a hand in computer. We use the Chi-Square method and check which variables are important and which are not important. Then we apply different data mining techniques on our normalize data and check which technique or method gives good results.The implementation of this thesis is in WEKA. We normalize our data and then apply different methods on this data. The methods which we used are Naïve Bayes, CART and KNN. We draw the Bland Altman and Spearman’s Correlation for checking the final results and prediction of data. The Bland Altman tells how the percentage of our confident level in this data is correct and Spearman’s Correlation tells us our relationship is strong. On the basis of results and analysis we see all three methods give nearly same results. But if we see our CART (J48 Decision Tree) it gives good result of under predicted and over predicted values that’s lies between -2 to +2. The correlation between the Actual and Predicted values is 0,794in CART. Cause gives the better percentage classification result then disability because it can use two classes.

Module property verification : A method to plan and perform quality verifications in modular architectures

Modular product architectures have generated numerous benefits for companies in terms of cost, lead-time and quality. The defined interfaces and the module’s properties decrease the effort to develop new product variants, and provide an opportunity to perform parallel tasks in design, manufacturing and assembly. The background of this thesis is that companies perform verifications (tests, inspections and controls) of products late, when most of the parts have been assembled. This extends the lead-time to delivery and ruins benefits from a modular product architecture; specifically when the verifications are extensive and the frequency of detected defects is high. Due to the number of product variants obtained from the modular product architecture, verifications must handle a wide range of equipment, instructions and goal values to ensure that high quality products can be delivered. As a result, the total benefits from a modular product architecture are difficult to achieve. This thesis describes a method for planning and performing verifications within a modular product architecture. The method supports companies by utilizing the defined modules for verifications already at module level, so called MPV (Module Property Verification). With MPV, defects are detected at an earlier point, compared to verification of a complete product, and the number of verifications is decreased. The MPV method is built up of three phases. In Phase A, candidate modules are evaluated on the basis of costs and lead-time of the verifications and the repair of defects. An MPV-index is obtained which quantifies the module and indicates if the module should be verified at product level or by MPV. In Phase B, the interface interaction between the modules is evaluated, as well as the distribution of properties among the modules. The purpose is to evaluate the extent to which supplementary verifications at product level is needed. Phase C supports a selection of the final verification strategy. The cost and lead-time for the supplementary verifications are considered together with the results from Phase A and B. The MPV method is based on a set of qualitative and quantitative measures and tools which provide an overview and support the achievement of cost and time efficient company specific verifications. A practical application in industry shows how the MPV method can be used, and the subsequent benefits

Test av patientenkät riktad till personer med levercirros i uppföljning vid leversjuksköterskemottagning: : En pilotstudie med mixad metod

Syfte: Att testa den patientenkät som används i utvärdering av en leversjuksköterskemottagning på patienter med dekompenserad levercirros för att undersöka upplevelsen av att besvara frågorna samt frågornas relevans till patientens situation. Metod: Pilotstudiens metod var mixad. Resultat: Spridningen av deltagarnas upplevelse av oro/obehag av enkäten var stor (VAS 6-100 millimeter). Vid få sjukdomssymtom väcktes oro om framtida sjukdomsutveckling men vid längre tids sjukdom kändes samtliga symtom igen, tankar om tidigare beteende uppstod vid alkoholsorsakad sjukdom. En mindre spridning (VAS 66-92 millimeter) sågs gällande hur viktiga/väsentliga frågorna upplevdes. Frågor om bemötande ansågs viktiga och påverkade upplevelsen av rätten till vård. Kompletterande frågor om individuellt anpassad information samt upplevelsen av delaktighet vid information efterfrågades. Deltagarna visade hög uppskattning (VAS 73-95 millimeter) till att sjukdomen/situation uppmärksammades genom enkäten. Besöken till sjuksköterskan skiljde sig från läkarbesök. Sjuksköterskan fokuserade på egenvård och mer tid fanns för information. För en informant innebar försöksverksamheten ökade antal sjukhusbesök, samordning innebar för- och nackdelar. Vid symtom på fatigue och nedsatt koncentrationsförmåga upplevdes enkäten lång, tvådelad enkät efterfrågades. Vid lindrig sjukdom upplevdes enkäten inte ansträngande. Språket var enkelt att förstå och innehållet upplevdes relevant. De öppna frågeställningarna tillförde inte något för de tre informanterna.

Development of a molecular test to determine the vitality status of Norway spruce (Picea abies) seedlings during frozen storage

In boreal forest regions, a great portion of forest tree seedlings are stored indoors in late autumn to prevent seedlings from outdoor winter damage. For seedlings to be able to survive in storage it is crucial that they store well and can cope with the dark and cold storage environment. The aim of this study was to search for genes that can determine the vitality status of Norway spruce (Picea abies (L.) Karst.) seedlings during frozen storage. Furthermore, the sensitivity of the ColdNSure (TM) test, a gene activity test that predicts storability was assessed. The storability of seedlings was tested biweekly by evaluating damage with the gene activity test and the electrolyte leakage test after freezing seedlings to -25 A degrees C (the SELdiff-25 method). In parallel, seedlings were frozen stored at -3 A degrees C. According to both methods, seedlings were considered storable from week 41. This also corresponded to the post storage results determined at the end of the storage period. In order to identify vitality indicators, Next Generation Sequencing (NGS) was performed on bud samples collected during storage. Comparing physiological post storage data to gene analysis data revealed numerous vitality related genes. To validate the results, a second trial was performed. In this trial, gene activity was better in predicting seedling storability than the conventional freezing test; this indicates a high sensitivity level of this molecular assay. For multiple indicators a clear switch between damaged and vital seedlings was observed. A collection of indicators will be used in the future development of a commercial vitality test.