Improvement of link failure restoration utilising MPLS as a means to maintain QoS

The availability of a network strongly depends on the frequency of service outages and the recovery time for each outage. The loss of network resources includes complete or partial failure of hardware and software components, power outages, scheduled maintenance such as software and hardware, operational errors such as configuration errors and acts of nature such as floods, tornadoes and earthquakes. This paper proposes a practical approach to the enhancement of QoS routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and an LSP request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis will examine several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision.

Improvement of link failure restoration utilising multi-protocol label switching (MPLS) as a means to maintain quality of service (QOS)

This paper proposes a practical approach to the enhancement of Quality of Service (QoS) routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and a Label Switched path (LSP) request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis examined several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision. Results obtained indicated that creating multi-repair paths and prioritizing packets reduces delay and increases throughput in which case the delays at the ingress/egress LSPs were low compared to when the signals had not been classified. Therefore the proposed scheme provided a means to improve the QoS in path restoration in MPLS using available network resources. Prioritizing the packets in the data plane has revealed that the amount of traffic transmitted using a medium and low priority Label Switch Paths (LSPs) does not have any impact on the explicit rate of the high priority LSP in which case the problem of a knock-on effect is eliminated.

Quality time [QoS in 802.11e]

Wireless local area networks (WLANs) based on the IEEE 802.11 standard are now widespread. Most are used to provide access for mobile devices to a conventional wired infrastructure, and some are used where wires are not possible, forming an ad hoc network of their own. There are several varieties at the physical or radio layer (802.11, 802.11a, 802.11b, 802.11g), with each featuring different data rates, modulation schemes and transmission frequencies. However, all of them share a common medium access control (MAC) layer. As this is largely based on a contention approach, it does not allow prioritising of traffic or stations, so it cannot easily provide the quality of service (QoS) required by time-sensitive applications, such as voice or video transmission. In order to address this shortfall of the technology, the IEEE set up a task group that is aiming to enhance the MAC layer protocol so that it can provide QoS. The latest draft at the time of writing is Draft 11, dated October 2004. The article describes the yet-to-be-ratified 802.11e standard and is based on that draft.

Infotainment across access devices: the perceptual impact of multimedia QoS

The introduction of multimedia on pervasive and mobile communication devices raises a number of perceptual quality issues. However, limited work has been done examining the 3-way interaction between use of equipment, user perceptual quality and quality of service. Our work measures user perceptual quality with the quality of perception (QoP) metrics which comprises levels of informational transfer (objective) and user satisfaction (subjective) when users are presented with multimedia video clips at three different frame rates, using four different display devices. Finally, our results will show that variation in frame-rate does not impact a user’s level of information assimilation (IA), however, does impact a users’ perception of multimedia video ‘quality’.

Modelling QoS of a pervasive MVNO/M2M using semi-group theory

This paper aims to develop a mathematical model based on semi-group theory, which allows to improve quality of service (QoS), including the reduction of the carbon path, in a pervasive environment of a Mobile Virtual Network Operator (MVNO). This paper generalise an interrelationship Machine to Machine (M2M) mathematical model, based on semi-group theory. This paper demonstrates that using available technology and with a solid mathematical model, is possible to streamline relationships between building agents, to control pervasive spaces so as to reduce the impact in carbon footprint through the reduction of GHG.