Studies on development of MgB2 superconductor with improved in-field critical current density

National Institute for Interdisciplinary Science and Technology

Recyclable Short Fibre Reinforced Plastics PP/Nylon and HDPE/Nylon composites

The study shows that standard plastics like polypropylene and high density polyethylene can be reinforced by adding nylon short fibres. Compared to the conventional glass reinforced thermoplastics this novel class of reinforced thermoplastics has the major advantage of recyclability. Hence such composites represent a new spectrum of recyclable polymer composites. The fibre length and fibre diameter used for reinforcement are critical parameters While there is a critical fibre length below which no effective reinforcement takes place, the reinforcement improves when the fibre diameter decreases due to increased surface area.While the fibres alone give moderate reinforcement, chemical modification of the matrix can further improve the strength and modulus of the composites. Maleic anhydride grafting in presence of styrene was found to be the most efficient chemical modification. While the fibre addition enhances the viscosity of the melt at lower shear rates, the enhancement at higher shear rate is only marginal. This shows that processing of the composite can be done in a similar way to that of the matrix polymer in high shear operations such as injection moulding. Another significant observation is the decrease in melt viscosity of the composite upon grafting. Thus chemical modification of matrix makes processing of the composite easier in addition to improving the mechanical load bearing capacity.For the development of a useful short fibre composite, selection of proper materials, optimum design with regard to the particular product and choosing proper processing parameters are most essential. Since there is a co-influence of many parameters, analytical solutions are difficult. Hence for selecting proper processing parameters 'rnold flow' software was utilized. The orientation of the fibres, mechanical properties, temperature profile, shrinkage, fill time etc. were determined using the software.Another interesting feature of the nylon fibre/PP and nylon fibre/HDPE composites is their thermal behaviour. Both nylon and PP degrade at the same temperature in single steps and hence the thermal degradation behaviour of the composites is also being predictable. It is observed that the thermal behaviour of the matrix or reinforcement does not affect each other. Almost similar behaviour is observed in the case of nylon fibre/HDPE composites. Another equally significant factor is the nucleating effect of nylon fibre when the composite melt cools down. In the presence of the fibre the onset of crystallization occurs at slightly higher temperature.When the matrix is modified by grafting, the onset of crystallization occurs at still higher temperature. Hence it may be calculated that one reason for the improvement in mechanical behaviour of the composite is the difference in crystallization behaviour of the matrix in presence of the fibre.As mentioned earlier, a major advantage of these composites is their recyclability. Two basic approaches may be employed for recycling namely, low temperature recycling and high temperature recycling. In the low temperature recycling, the recycling is done at a temperature above the melting point of the matrix, but below that of the fibres while in the high temperature route. the recycling is done at a temperature above the melting points of both matrix and fibre. The former is particularly interesting in that the recycled material has equal or even better mechanical properties compared to the initial product. This is possible because the orientation of the fibre can improve with successive recycling. Hence such recycled composites can be used for the same applications for which the original composite was developed. In high temperature recycling, the composite is converted into a blend and hence the properties will be inferior to that of the original composite, but will be higher than that of the matrix material alone.

Effect of pore size on the catalytic activities of K-I 0 clay and H-zeolites for the acetalization of ketones with methanol

One-pot acetalizations of cyclohexanone. acetophenone and benzophenone were carried out using methanol over H-montmorillonite clay (a mesoporous material). silica, alumina, and different zeolites such as HFAU-Y.HBeta, H-ZSM-5, and H-mordenite. In all the cases a single product-the corresponding dimethylacetal-was obtained in high yields. Hemiacetal formation was not observed with any catalyst. A comparison of catalytic activity indicated that montmorillonite K-10 is the most active catalyst for the reaction. As evidenced by the reaction time studies, the catalyst decay is greater over the zeolite catalyst than over the clay.

Influence of residual cations (Na+, K+ and Mg2+) in the alkylation activity of benzene with 1-octene over rare earth metal ion exchanged FAU–Y zeolite

The effect of residual cations in rare earth metal modified faujasite–Y zeolite has been monitored using magic angle spinning NMR spectral analysis and catalytic activity studies. The second metal ions being used are Na+, K+ and Mg+. From a comparison of the spectra of different samples, it is concluded that potassium and magnesium exchange causes a greater downfield shift in the 29Si NMR peaks. Also, lanthanum exchanged samples show migration behavior from large cages to small cages, which causes the redistribution of second counter cations. It is also observed that Mg2+ causes the most effective migration of lanthanum ions due to its greater charge. The prepared systems were effectively employed for the alkylation of benzene with 1-octene in the vapor phase. From the deactivation studies it is observed that the as-exchanged zeolites possess better stability towards reaction condition over the pure HFAU zeolite.

Development of Best Practices for Ship Recycling Processes

Ship recycling has been considered as the best means to dispose off an obsolete ship. The current state of art of technology combined with the demands of sustainable developments from the global maritime industrial sector has modified the status of erstwhile ‘ship breaking’ involving ship scrap business to a modern industry undertaking dismantling of ships and recycling/reusing the dismantled products in a supply chain of pre owned product market by following the principles of recycling. Industries will have to formulate a set of best practices and blend them with the engineering activities for producing better quality products, improving the productivity and for achieving improved performances related to sustainable development. Improved performance by industries in a sustainable development perspective is accomplished only by implementing the 4E principles, ie.,. ecofriendliness, engineering efficiency, energy conservation and ergonomics in their core operations. The present study has done a comprehensive investigation into various ship recycling operations for formulating a set of best practices.Being the ultimate life cycle stage of a ship, ship recycling activities incorporate certain commercial procedures well in advance to facilitate the objectives of dismantling and recycling/reusing of various parts of the vessel. Thorough knowledge regarding these background procedures in ship recycling is essential for examining and understanding the industrial business operations associated with it. As a first step, the practices followed in merchant shipping operations regarding the decision on decommissioning have been and made available in the thesis. Brief description about the positioning methods and important preparations for the most feasible ship recycling method ie.,. beach method have been provided as a part of the outline of the background information. Available sources of guidelines, codes and rules & regulations for ship recycling have been compiled and included in the discussion.Very brief summary of practices in major ship recycling destinations has been prepared and listed for providing an overview of the global ship recycling activities. The present status of ship recycling by treating it as a full fledged engineering industry has been brought out to establish the need for looking into the development of the best practices. Major engineering attributes of ship as a unique engineering product and the significant influencing factors on her life cycle stage operations have been studied and added to the information base on ship recycling. Role of ship recycling industry as an important player in global sustainable development efforts has been reviewed by analysing the benefits of ship recycling. A brief synopsis on the state of art of ship recycling in major international ship recycling centres has also been incorporated in the backdrop knowledgebase generation on ship recycling processes.Publications available in this field have been reviewed and classified into five subject categories viz., Infrastructure for recycling yards and methods of dismantling, Rules regarding ship recycling activities, Environmental and safety aspects of ship recycling, Role of naval architects and ship classification societies, Application of information technology and Demand forecasting. The inference from the literature survey have been summarised and recorded. Noticeable observations in the inference include need of creation of a comprehensive knowledgebase on ship recycling and its effective implementation in the industry and the insignificant involvement of naval architects and shipbuilding engineers in ship recycling industry. These two important inferences and the message conveyed by them have been addressed with due importance in the subsequent part of the present study.As a part of the study the importance of demand forecasting in ship recycling has been introduced and presented. A sample input for ship recycling data for implementation of computer based methods of demand forecasting has been presented in this section of the thesis.The interdisciplinary nature of engineering processes involved in ship recycling has been identified as one of the important features of this industry. The present study has identified more than a dozen major stake holders in ship recycling having their own interests and roles. It has also been observed that most of the ship recycling activities is carried out in South East Asian countries where the beach based ship recycling is done in yards without proper infrastructure support. A model of beach based ship recycling has been developed and the roles, responsibilities and the mutual interactions of the elements of the system have been documented as a part of the study Subsequently the need of a generation of a wide knowledgebase on ship recycling activities as pointed out by the literature survey has been addressed. The information base and source of expertise required to build a broad knowledgebase on ship recycling operations have been identified and tabulated. Eleven important ship recycling processes have been identified and a brief sketch of steps involved in these processes have been examined and addressed in detail. Based on these findings, a detailed sequential disassembly process plan of ship recycling has been prepared and charted. After having established the need of best practices in ship recycling initially, the present study here identifies development of a user friendly expert system for ship recycling process as one of the constituents of the proposed best practises. A user friendly expert system has been developed for beach based ship recycling processes and is named as Ship Recycling Recommender (SRR). Two important functions of SRR, first one for the ‘Administrators’, the stake holders at the helm of the ship recycling affairs and second one for the ‘Users’, the stake holders who execute the actual dismantling have been presented by highlighting the steps involved in the execution of the software. The important output generated, ie.,. recommended practices for ship dismantling processes and safe handling information on materials present onboard have been presented with the help of ship recycling reports generated by the expert system. A brief account of necessity of having a ship recycling work content estimation as part of the best practices has been presented in the study. This is supported by a detailed work estimation schedule for the same as one of the appendices.As mentioned earlier, a definite lack of involvement of naval architect has been observed in development of methodologies for improving the status of ship recycling industry. Present study has put forward a holistic approach to review the status of ship recycling not simply as end of life activity of all ‘time expired’ vessels, but as a focal point of integrating all life cycle activities. A new engineering design philosophy targeting sustainable development of marine industrial domain, named design for ship recycling has been identified, formulated and presented. A new model of ship life cycle has been proposed by adding few stages to the traditional life cycle after analysing their critical role in accomplishing clean and safe end of life and partial dismantling of ships. Two applications of design for ship recycling viz, recyclability of ships and her products and allotment of Green Safety Index for ships have been presented as a part of implementation of the philosophy in actual practice.

Studies,Design and Development of Network Security Enhancement Services Using Novel Cryptographic Algorithms

Internet today has become a vital part of day to day life, owing to the revolutionary changes it has brought about in various fields. Dependence on the Internet as an information highway and knowledge bank is exponentially increasing so that a going back is beyond imagination. Transfer of critical information is also being carried out through the Internet. This widespread use of the Internet coupled with the tremendous growth in e-commerce and m-commerce has created a vital need for infonnation security.Internet has also become an active field of crackers and intruders. The whole development in this area can become null and void if fool-proof security of the data is not ensured without a chance of being adulterated. It is, hence a challenge before the professional community to develop systems to ensure security of the data sent through the Internet.Stream ciphers, hash functions and message authentication codes play vital roles in providing security services like confidentiality, integrity and authentication of the data sent through the Internet. There are several ·such popular and dependable techniques, which have been in use widely, for quite a long time. This long term exposure makes them vulnerable to successful or near successful attempts for attacks. Hence it is the need of the hour to develop new algorithms with better security.Hence studies were conducted on various types of algorithms being used in this area. Focus was given to identify the properties imparting security at this stage. By making use of a perception derived from these studies, new algorithms were designed. Performances of these algorithms were then studied followed by necessary modifications to yield an improved system consisting of a new stream cipher algorithm MAJE4, a new hash code JERIM- 320 and a new message authentication code MACJER-320. Detailed analysis and comparison with the existing popular schemes were also carried out to establish the security levels.The Secure Socket Layer (SSL) I Transport Layer Security (TLS) protocol is one of the most widely used security protocols in Internet. The cryptographic algorithms RC4 and HMAC have been in use for achieving security services like confidentiality and authentication in the SSL I TLS. But recent attacks on RC4 and HMAC have raised questions about the reliability of these algorithms. Hence MAJE4 and MACJER-320 have been proposed as substitutes for them. Detailed studies on the performance of these new algorithms were carried out; it has been observed that they are dependable alternatives.

Bioactivity Profile of Polyunsaturated Fattyacid extracts from Sardinella longiceps and Sardinella fimbriata – A comparative study

The oceans have proved to be an interminable source of new and effective drugs. Innumerable studies have proved that specific compounds isolated from marine organisms have great nutritional and pharmaceutical value. Polyunsaturated fattyacids (PUFA) in general are known for their dietary benefits in preventing and curing several critical ailments including Coronary heart disease (CHD) and cancers of various kinds. Eicosapentaenoic Acid (EPA) and Docosahexaenoic Acid (DHA) are two PUFA which are entirely marine in origin – and small Clupeoid fishes like sardines are known to be excellent sources of these two compounds. In this study, we selected two widely available Sardine species in the west coast, Sardinella longiceps and Sardinella fimbriata, for a comparative analysis of their bioactive properties. Both these sardines are known to be rich in EPA and DHA, however considerable seasonal variation in its PUFA content was expected and these variations studied. An extraction procedure to isolate PUFA at high purity levels was identified and the extracts obtained thus were studied for anti-bacterial, anti-diabetic and anti-cancerous properties.Samples of both the sardines were collected from landing centre, measured and their gut content analysed in four different months of the year – viz. June, September, December and March. The fish samples were analyzed for fattyacid using FAME method using gas chromatography to identify the full range of fattyacids and their respective concentration in each of the samples. The fattyacids were expressed in mg/g meat and later converted to percentage values against total fatty acids and total PUFA content. Fattyacids during winter season (Dec-Mar) were found to be generally higher than spawning season (June-Sept). PUFA dominated the profiles of both species and average PUFA content was also higher during winter. However, it was found that S. longiceps had proportionately higher EPA as compared to S. fimbriata which was DHA rich. Percentage of EPA and DHA also varied across months for both species – the spawning season seemed to show higher EPA content in S. longiceps and higher DHA content in S. fimbriata. Gut content analysis indicate that adult S. fimbriata is partial to zooplanktons which are DHA rich while adult S. longiceps feed mainly on EPA rich phytoplankton. Juveniles of both species, found mainly in winter, had a gut content showing more mixed diet. This difference in the feeding pattern reflect clearly in their PUFA profile – adult S. longiceps, which dominate the catch during the spawn season, feeding mostly on phytoplankton is concentrated with EPA while the juveniles which are found mostly in the winter season has slightly less EPA proportion as compared to adults. The same is true for S. fimbriata adults that are caught mostly in the spawning season; being rich in DHA as they feed mainly on zooplankton while the juveniles caught during winter season has a relatively lower concentration of DHA in their total PUFA.Various extraction procedures are known to obtain PUFA from fish oil. However, most of them do not give high purity and do not use materials indicated as safe. PUFA extracts have to be edible and should not have harmful substances for applying on mice and human subjects. Some PUFA extraction procedures, though pure and non-toxic, might induce cis-trans conversions during the extraction process. This conversion destroys the benefits of PUFA and at times is harmful to human body. A method free from these limitations has been standardized for this study. Gas Chromatography was performed on the extracts thus made to ensure that it is substantially pure. EPA: DHA ratios for both samples were derived - for S. longiceps this ratio was 3:2, while it was 3:8 for S. fimbriata.Eight common strains of gram positive and gram negative bacterial strains were subjected to the PUFA extracts from both species dissolved in acetone solution using Agar Well Diffusion method. The activity was studied against an acetone control. At the end of incubation period, zones of inhibition were measured to estimate the activity. Minimum inhibitory concentration for each of the active combinations was calculated by keeping p < 0.01 as significant. Four of the bacteria including multi-resistant Staphylococcus aureus were shown to be inhibited by the fish extracts. It was also found that the extracts from S. fimbriata were better than the one from S. longiceps in annihilating harmful bacteria.Four groups of mice subjects were studied to evaluate the antidiabetic properties of the PUFA extracts. Three groups were induced diabetes by administration of alloxan tetra hydrate. One group without diabetes was kept as control and another with diabetes was kept as diabetic control. For two diabetic groups, a prescribed amount of fish extracts were fed from each of the extracts. The biochemical parameters like serum glucose, total cholesterol, LDL & HDL cholesterol, triglycerides, urea and creatinine were sampled from all four groups at regular intervals of 7 days for a period of 28 days. It was found that groups fed with fish extracts had marked improvement in the levels of total LDL & HDL cholesterol, triglycerides and creatinine. Groups fed with extracts from S. fimbriata seem to have fared better as compared to S. longiceps. However, both groups did not show any marked improvement in blood glucose levels or levels of urea.Cell lines of MCF-7 (Breast Cancer) and DU-145 (Prostate Cancer) were used to analyse the cytotoxicity of the PUFA extracts. Both cell lines were subjected to MTT Assay and later the plates were read using an ELISA reader at a wavelength of 570nm. It was found that both extracts had significant cytotoxic effects against both cell lines and a peak cytotoxicity of 85-90% was apparent. IC50 values were calculated from the graphs and it was found that S. longiceps extracts had a slightly lower IC50 value indicating that it is toxic even at a lower concentration as compared to extracts from S. fimbriata.This study summarizes the bioactivity profile of PUFA extracts and provides recommendation for dietary intake; fish based nutritional industry and indigenous pharmaceutical industry. Possible future directions of this study are also elaborated.

Preparation and Characterization ofHigh-k Aluminum Oxide Thin Films by Atomic Layer Deposition for Gate Dielectric Applications

Present work deals with the Preparation and characterization of high-k aluminum oxide thin films by atomic layer deposition for gate dielectric applications.The ever-increasing demand for functionality and speed for semiconductor applications requires enhanced performance, which is achieved by the continuous miniaturization of CMOS dimensions. Because of this miniaturization, several parameters, such as the dielectric thickness, come within reach of their physical limit. As the required oxide thickness approaches the sub- l nm range, SiO 2 become unsuitable as a gate dielectric because its limited physical thickness results in excessive leakage current through the gate stack, affecting the long-term reliability of the device. This leakage issue is solved in the 45 mn technology node by the integration of high-k based gate dielectrics, as their higher k-value allows a physically thicker layer while targeting the same capacitance and Equivalent Oxide Thickness (EOT). Moreover, Intel announced that Atomic Layer Deposition (ALD) would be applied to grow these materials on the Si substrate. ALD is based on the sequential use of self-limiting surface reactions of a metallic and oxidizing precursor. This self-limiting feature allows control of material growth and properties at the atomic level, which makes ALD well-suited for the deposition of highly uniform and conformal layers in CMOS devices, even if these have challenging 3D topologies with high aspect-ratios. ALD has currently acquired the status of state-of-the-art and most preferred deposition technique, for producing nano layers of various materials of technological importance. This technique can be adapted to different situations where precision in thickness and perfection in structures are required, especially in the microelectronic scenario.

A critical study of major construction projects in kerala vis-a-vis effectiveness in project implementation

Chapter 1 presents a brief note on the state at which the construction industry stands at present, bringing into focus the significance of the critical study. Relevance of the study, area of investigation and objectives of the study are outlined in this chapter. The 2nd chapter presents a review of the literature on the relevant areas. In the third chapter an analysis on time and cost overrun in construction highlighting the major factors responsible for it has been done. A couple of case studies to estimate loss to the nation on account of delay in construction have been presented in the chapter. The need for an appropriate estimate and a competent contractor has been emphasised for improving effectiveness in the project implementation. Certain useful equations and thoughts have been formulated on this area in this chapter that can be followed in State PWD and other Govt. organisations. Case studies on project implementation of major projects undertaken by Government sponsored/supported organizations in Kerala have been dealt with in Chapter 4. A detailed description of the project of Kerala Legislature Complex with a critical analysis has been given in this chapter. A detailed account of the investigations carried out on the construction of International Stadium, a sports project of Greater Cochin Development Authority is included here. The project details of Cochin International Airport at Nedumbassery, its promoters and contractors are also discussed in Chapter 4. Various aspects of implementation which led the above projects successful have been discussed in chapter 5. The data collected were analysed through discussion and perceptions to arrive at certain conclusions. The emergence of front-loaded contract and its impact on economics of the project execution are dealt with in this chapter. Analysis of delays in respect of the various project narrated in chapter 3 has been done here. The root causes of the project time and overrun and its remedial measures are also enlisted in this chapter. Study of cost and time overrun of any construction project IS a part of construction management. Under the present environment of heavy investment on construction activities in India, the consequences of mismanagement many a time lead to excessive expenditure which are not be avoidable. Cost consciousness, therefore has to be keener than ever before. Optimization in investment can be achieved by improved dynamism in construction management. The successful completion of coristruction projects within the specified programme, optimizing three major attributes of the process - quality, schedule and costs - has become the most valuable and challenging task for the engineer - managers to perform. So, the various aspects of construction management such as cost control, schedule control, quality assurance, management techniques etc. have also been discussed in this fifth chapter. Chapter 6 summarises the conclusions drawn from the above criticalr1 of rhajor construction projects in Kerala.

IA Critical Study of the Impact of Institutional Finance on Agriculture in Selected Villages of Ernakulam Revenue District

Vast changes have taken place in the field of institutional rural credit in India since the nationalisation of nineteen commercial banks in 1969. The supply of institutional finance to cultivators amounted to 63.2 percent of the total credit in 1981 compared to 31.2 percent in 1971. Insti tutionalisation of agricultural credit envisaged two objectives in general. One was to emancipate cultivators and farmers from the clutches of indigenous financiers and money lenders. The second was to make farmers financially capable of adopting the new technology or improved practices in agriculture so as to increase their agricultural production and thereby contributing to the development of agriculture in India. Though vast literature on Institutional Credi t and agriculture is available, no indepth and serious work examining thoroughly the cause of credit diversion has been undertaken so far. The present study is an attempt to fill up this gap. The study will be helpful to lending insti tutions, viz. Co-ope:r-atives, Commercial banks and various other insti tutional agencies in connection with their lending activity_ Also, the study will help government in .formulating proper policies that will insure a preferential treatment in favour of the most needy category of farmers and cultivators with respect to agricultural credit disbursement

Criminal justice system in pondicherry - a comparative critical study of the past and the presen

The Union Territory of Pondicherry prior to its merger with the Indian Union was a French Colony. The erstwhile territory of Pondicherry along with its hamlets, namely, KARAIKKAL, MAHE and YANAM was administered by the French Regime. Before it was established by French in 1 6 74 A.D. it was part of Vijayanagara Empire. Prior to this, Pondicherry was a part of the Kingdom of Chola and Pallava Kings. During French Regime, the laws which were in force in France in relation to administration of civil and criminal justice were extended to the erstwhile Territory of Pondicherry. Thus while Pondicherry stood influenced by the Inquisitorial system since the beginning of the 18th century, the neighboring states forming part of the Indian Union since Independence came under the Influence of the British system, viz. accusatorial system. The territory of Pondicherry, for administrative reasons, came to be merged with the Indian Union in the early 60's. Following the merger, the Indian administration sought to extent its own laws from time to time replacing erstwhile French Laws, however, subject to certain savings. Thus the transitional period witnessed consequential changes in the administration of the territory, including the sphere of judicial system. Since I 963, the Union Territory of Pondicherry was brought under the spell of the Indian Legal System The people in Pondicherry ' thus have had the benefit of experiencing both the svstems. Their experiences will be of much help to those who undertake comparative studies in law. The plus and minus points of the respective systems help one to develop a detachment that helps independent evaluation of the svstents. The result of these studies could be relevant in revitalising our criminal systems.The present system is evaluated in the light of the past system. New dimensions are added by way' of an empirical study also.

Studies on osmoregulation in the penaeid prawn Metapenaeus dobsoni (Miers)

Metapenaeus dobsoni (Miers) is the most abundant species along the coast of Kerala. It is cultured extensively by adoption of traditional farming practices. The geographical location and water source determines the seasonal and annual environmental fluctuations the prawn farming systems experiences. The life cycle of the shrimp includes its migration to the coastal deeper waters for spawning and the immigration of larvae to the estuaries for growth. The survival of the species in such complex ecosystems is thus critical to its life cycle. The animal adapts itself to different environments through a physiological process known as osmoregulation. The present study on osmoregulation in the penaeid prawn Metapenaeus dobsoni was thus undertaken to understand the mechanism adopted by this species to survive in different environments. A number of experimental work have been conducted to understand the effect of salinity on the internal variations. However the effect of the complex environmental conditions as existent in nature on the osmotic variations in this species has not been dealt with in any of the earlier studies.

Evaluation of the Power Consumption of Routing Protocols for Wireless Sensor Networks

Sensor networks are one of the fastest growing areas in broad of a packet is in transit at any one time. In GBR, each node in the network can look at itsneighbors wireless ad hoc networking (? Eld. A sensor node, typically'hop count (depth) and use this to decide which node to forward contains signal-processing circuits, micro-controllers and a the packet on to. If the nodes' power level drops below a wireless transmitter/receiver antenna. Energy saving is one certain level it will increase the depth to discourage trafiE of the critical issue for sensor networks since most sensors are equipped with non-rechargeable batteries that have limitedlifetime. Routing schemes are used to transfer data collectedby sensor nodes to base stations. In the literature many routing protocols for wireless sensor networks are suggested. In this work, four routing protocols for wireless sensor networks viz Flooding, Gossiping, GBR and LEACH have been simulated using TinyOS and their power consumption is studied using PowerTOSSIM. A realization of these protocols has beencarried out using Mica2 Motes.

IRIS BIOMETRIC RECOGNITION SYSTEM EMPLOYING CANNY OPERATOR

Biometrics has become important in security applications. In comparison with many other biometric features, iris recognition has very high recognition accuracy because it depends on iris which is located in a place that still stable throughout human life and the probability to find two identical iris's is close to zero. The identification system consists of several stages including segmentation stage which is the most serious and critical one. The current segmentation methods still have limitation in localizing the iris due to circular shape consideration of the pupil. In this research, Daugman method is done to investigate the segmentation techniques. Eyelid detection is another step that has been included in this study as a part of segmentation stage to localize the iris accurately and remove unwanted area that might be included. The obtained iris region is encoded using haar wavelets to construct the iris code, which contains the most discriminating feature in the iris pattern. Hamming distance is used for comparison of iris templates in the recognition stage. The dataset which is used for the study is UBIRIS database. A comparative study of different edge detector operator is performed. It is observed that canny operator is best suited to extract most of the edges to generate the iris code for comparison. Recognition rate of 89% and rejection rate of 95% is achieved