Studies on prevulcanization of rubber latex with special reference to influence of storage and after treatments on properties of films

Systematic investigations on prevulcanization of NR latex with special reference to the influence of storage of latex and after-treatments of films, have been carried out. The other aspects studied include the effect of temperature on sulphur prevulcanization, the extent of crosslinking, tensile properties, stress relaxation characteristics, water absorption and leaching characteristics of prevulcanizcd latex films

Effect of Chromium Doping on the Diffraction Efficiency of Methylene Blue Sensitized PVA/Acrylamide Films

The effect of chromium doping on methylene blue sensitized Poly (vinyl alcohol)/Acrylamide was carried out by varying the ratios of Ammonium dichromate and methylene blue. In the case of films without ammonium dichromate, the diffraction efficiency was found to decrease on storage. On chromium doping the storage life was improved. Interestingly, a self-enhancement in efficiency was observed for a particular ratio of methylene blue and ammonium dichromate.

Optical and electrical properties of co-sputtered amorphous transparent conducting zinc indium tin oxide thin films

Highly conductive and transparent thin films of amorphous zinc indium tin oxide are prepared at room temperature by co-sputtering of zinc 10 oxide and indium tin oxide. Cationic contents in the films are varied by adjusting the power to the sputtering targets. Optical transmission study of 11 films showed an average transmission greater than 85% across the visible region. Maximum conductivity of 6×102 S cm−1 is obtained for Zn/In/ 12 Sn atomic ratio 0.4/0.4/0.2 in the film. Hall mobility strongly depends on carrier concentration and maximum mobility obtained is 18 cm2 V−1 s−1 13 at a carrier concentration of 2.1×1020 cm−3. Optical band gap of films varied from 3.44 eV to 3 eV with the increase of zinc content in the film 14 while the refractive index of the films at 600 nm is about 2.0.

Structural, topographical and magnetic evolution of RF-sputtered Fe-Ni alloy based thin films with thermal annealing

Metglas 2826 MB having a nominal composition of Fe40Ni38Mo4B18 is an excellent soft magnetic material and finds application in sensors and memory heads. However, the thin-film forms of Fe40Ni38Mo4B18 are seldom studied, although they are important in micro-electro-mechanical systems/nano-electromechanical systems devices. The stoichiometry of the film plays a vital role in determining the structural and magnetic properties of Fe40Ni38Mo4B18 thin films: retaining the composition in thin films is a challenge. Thin films of 52 nm thickness were fabricated by RF sputtering technique on silicon substrate from a target of nominal composition of Fe40Ni38Mo4B18. The films were annealed at temperatures of 400 °C and 600 °C. The micro-structural studies of films using glancing x-ray diffractometer (GXRD) and transmission electron microscope (TEM) revealed that pristine films are crystalline with (FeNiMo)23B6 phase. Atomic force microscope (AFM) images were subjected to power spectral density analysis to understand the probable surface evolution mechanism during sputtering and annealing. X-ray photoelectron spectroscopy (XPS) was employed to determine the film composition. The sluggish growth of crystallites with annealing is attributed to the presence of molybdenum in the thin film. The observed changes in magnetic properties were correlated with annealing induced structural, compositional and morphological changes

Structural And Surface Morphological Investigation Of Formation Stages Of Highly (002) Oriented Zno Films On Glass Substrates By Spray Pyrolysis Method

ZnO thin films were coated on amorphous glass substrate at various temperatures in the range 160-500 0C by spray pyrolysis method. The as deposited films were characterised by using XRD and SEM. Wurtzite phase of ZnO was formed at a substrate temperature of 400 0C, highly oriented (002) phase was developed with respect to increase of substrate temperature from 450 to 500 0C. Morphological and growth mode of these films were analyzed with respect to structural orientation of films from wurtzite to highly (002) oriented phase. Present study reveals that substrate temperature was one of the important parameters which determine the crystalline quality, population of defects, grain size, orientation and morphology of the films

Legal Control of Fishing Industry in Kerala

This work is a study on ‘Legal Control of Fishing Industry in Kerala.Fishery and Fishery-related legislations are sought to be examined in the light of scientific opinion and judicial decisionsThis work is divided into five Part.The thrust of time Study is on the success of legislative measures in attempting to achieve socio-economic justice for the fishermen community.Fishing is more an avocation than an industry. It is basically the avocation of the artisanal or traditional fishermen who depend on it for their livelihood. As an ‘industry’, it is a generator of employment, income and wealth.The modern tendency in national legislations is to integrate legal proivisions relating to EEZ fisheries into the general fisheries legislation.Chartered fishing was introduced by the Central Government during 1977-78 to establish the abundance and distribution of fishery resources in Indian EEZ, for transfer of technology and for related purposes.Going by the provisions of Articles 61 and 62 of the U.N. Convention on the Law of the Sea, 1982, foreign fishing need be permitted in our EEZ area only if there is any surplus left after meeting our national requirements.Conservation of the renewable fishery resources should start with identification of the species, their habitats, feeding and breeding patterns, their classification and characteristics. Fishing patterns and their impact on different species and areas require to be examined and investigated.the Central Government, that the Kerala Marine Fishing Regulation Act, 1980 was passed.our traditional fishermen that our Governments in power in Kerala resorted to the appointment of Commissions after Commissions to enquire into the problems of resource management and conservation of the resources. The implementation of the recommendations of these Commissions is the need of the times.General infrastructure has increased to a certain extent in the fishery villages; but it is more the result of the development efforts of the State rather than due to increase in earnings from fishing. Fisherwomen ar e still unable to enjoy the status and role expected of them in the society and the family.Around 120 million people around the tuorld are economically dependent on fisheries. In developing countries like India, small-scale fishers are also the primary suppliers of fish, particularly for local consumption. A most important role of the fisheries sector is as a source of domestically produced food. Fish, as a food item, is a nutrient and it has great medicinal value.Consumers in our country face a dramatic rise in fish prices as our ‘fishing industry’ is linked with lucrative markets in industrial countries. Autonomy of States should be attempted to be maintained to the extent possible with the help and co-operation of the Centre. Regional co-operation of the coastal states interse and with the Centre should be attempted to be achieved under the leadership of the Centre in matters of regional concern. At time national level, a ifisheries management policy and plan should be framed in conformity with the national economic policies and plans as also keeping pace with the local and regional needs and priorities. Any such policy, plan and legislation should strive to achieve sustainability of the resources as well as support to the subsistence sector.

Rights of the Prisoner: An Evolving Jurisprudence

Imprisonment is the most common method of punishment resorted to by almost all legal systems.The new theories of crime causation propounded in the latter half of the nineteenth century gave rise to the feeling that the prisons could be used as appropriate institutions for reforming the offenders. It called for individualisation of punishment.As a result of international movements for humanisation of prisons the judiciary' in tine common law countries started taking active interest in prisoner's treatment.Various studies reveal that much has been done in America to improve the lot of prisoners and to treat them as human beings.The courts there have gone to the extent of saying that there is no iron curtain between a prisoner and the constitution. Most of the rights available to citizens except those which they cannot enjoy due to the conditions of incarceration have also been granted to prisoner.In India also the judiciary has come forward to protect the rights of the prisoners.Maneka Gandhi is a turning point in prisoner's rights.The repeated intervention of courts in prison administration project the view that prisoners have been denied the basic human rights.The High Courts and the Supreme Court of India have been gradually exercising jurisdiction ixl assuming prison justice, including improving the quality of food and amenities, payment of wages and appropriate standards of medical care. Access to courts must be made easier to the aggrieved prisoners.The government should come forward along with some public spirited citizens and voluntary organisations to form a "discharged prisoner“ aid society. The society should exploit opportunities for rehabilitation of prisoners after their release.Most of the prison buildings in the State of Kerala are ill-equipped, ill furnished and without proper ventilation or sanitation and with insufficient water supply arrangements.In India prisoners and prisons today are governed by the old central legislations like Prisons Act l894 Prisoners Act 1900 and the Transfer of Prisoners Act 1950.

Compensation to Workmen for Industrial Injuries

This thesis Entitled compensation to workmen for industrial injuries.Evaluation of the different forms of liability for compensating industrial injuries makes it evident that the liability under the social insurance scheme is the most befitting one, as it eliminates the problem of evasion of liability by the employer by providing for sharing of liability. Liability for compensation under the workmen's Compensation Act, 1923 and the Employees' State Insurance Act, 1948 arises only in the case of accidents, arising in the course of and out of employment. Majority of the workers, covered by the workmen's Compensation Act, have supported lumpsum payment of compensation under the Act. It appears that workers are ignorant of the cemerits of lumpsum payment. So, the workers should be properly educated by the Inspectorate, proposed above, about the comparative advantages of periodical payments. It is suggested that the workmens Compensation Act, 1923 may be amended, imposing fee upon the parties for each adjournment. It is also suggested that provision may be made in the workmens Compensation Act, 1923 for the expeditious despatch of amendments of the Workmen's Compensation Act, 1923, the Workmens· Compensation Rules, 1924 and the Schedules, made from time to time, to the comrnissioners for workmens Compensation, This will help them mete out justice to an injured workman, as required by the changes in the law. The Employees' State Insurance Act, 1948 and the Rules may be amended, requiring the employers to provide the employees with necessary information, in the vernacular language, about the employment injury benefits available under the Employees' State Insurance Act, 1948 and the formalities for obtaining the same. This will help the illiterate employees, especially the casual ones, avail of employment injury benefits. Changes in the law, on the lines suggested above, are imperative to make the system of compensation for industrial injuries prove effective and beneficial to injured workmen.

Optimization of parameters of chemical spray pyrolysis technique to get n and p-type layers of SnS

SnS thin films were prepared using automated chemical spray pyrolysis (CSP) technique. Single-phase, p-type, stoichiometric, SnS films with direct band gap of 1.33 eV and having very high absorption coefficient (N105/cm) were deposited at substrate temperature of 375 °C. The role of substrate temperature in determining the optoelectronic and structural properties of SnS films was established and concentration ratios of anionic and cationic precursor solutions were optimized. n-type SnS samples were also prepared using CSP technique at the same substrate temperature of 375 °C, which facilitates sequential deposition of SnS homojunction. A comprehensive analysis of both types of films was done using x-ray diffraction, energy dispersive x-ray analysis, scanning electron microscopy, atomic force microscopy, optical absorption and electrical measurements. Deposition temperatures required for growth of other binary sulfide phases of tin such as SnS2, Sn2S3 were also determined

Development of selected electro-active polymer-ceramic nanocomposites as pyroelectric thermal/infrared detector materials

The present work emphasises on the synthesis and characterization of electro-active polymer-ceramic nanocomposites which can be used for pyroelectric thermal/infrared detection applications. Two sets of samples belong to polymer-microcrystalline composites have also been investigated in the work. The polymers used in the work have been commercially available ones, but the nanoceramics have been synthesized following simple chemical routes and aqueous organic gel routes. After characterizing the nanoceramics for their structure by powder XRD, they have been dispersed in liquid polymer and sonicated for uniform dispersion. The viscous mixture so formed was cast in the form of films for experimentation. Samples with volume fraction of the ceramic phase varied from 0 to 0.25 have been prepared. Solution growth was followed to prepare microcrystalline samples for the polymer-microcrystalline composites. The physical properties that determine the pyroelectric sensitivity of a material are dielectric constant, dielectric loss, pyroelectric coefficient, thermal conductivity and specific heat capacity. These parameters have been determined for all the samples and compositions reported in this work.The pyroelectric figures of merit for all the samples were determined. The pyroelectric figures of merit that determine the pyroelectric sensitivity of a material are current sensitivity, voltage responsivity and detectivity. All these have been determined for each set of samples and reported in the thesis. In order to assess the flexibility and mouldability of the composites we have measured the Shore hardness of each of the composites by indentation technique and compared with the pyroelectric figures of merit. Some important factors considered during the material fabrication stages were maximum flexibility and maximum figures of merit for pyroelectric thermal/IR detection applications. In order to achieve these goals, all the samples are synthesized as composites of polymers and nano/microcrystalline particles and are prepared in the form of freestanding films. The selected polymer matrices and particle inclusions possess good pyroelectric coefficients, low thermal and dielectric properties, so that good pyroelectric figures of merit could be achieved. The salient features of the work include the particle size of the selected ceramic materials. Since they are in nanometer size it was possible to achieve high flexibility and moldability with high figures of merit for even low volume fractions of inclusions of the prepared nanocrystalline composites. In the case of microcrystalline TGS and DTGS, their composites in PU matrix protect them from fragility and humidity susceptibility and made them for environmental friendly applications.

Human Rights Violations in Police Custody

Human rights are the basic rights of every individual against the state or any other public authority as a member of the human family irrespective of any other consideration. Thus every individual of the society has the inherent right to be treated with dignity in all situations including arrest and keeping in custody by the police. Rights of an individual in police custody are protected basically by the Indian Constitution and by various other laws like Code of Criminal Procedure, Evidence Act, Indian Penal Code and Protection of Human Rights Act. The term `custody' is defined neither in procedural nor in substantive laws. The word custody means protective care. The expression `police custody' as used in sec. 27 of Evidence Act does not necessarily mean formal arrest. In India with special reference to Kerala and evolution and development of the concept of human rights and various kinds of human rights violations in police custody in different stages of history. Human rights activists and various voluntary organisations reveals that there are so many factors contributing towards the causes of violations of human rights by police. Sociological causes like ambivalent outlook of the society with respect to the use of third degree methods by the police, economic causes like meager salary and inadequate living conditions, rampant corruption in police service, unnecessary political interference in the crime investigation, work load of police personnel without any time limit and periodic holidays, unnecessary pressure from superior police officers and the general public for speedy detection causing great mental strain to the investigating officers, defective system of recruitment and training, imperfect system of investigation and lack of public co-operation are some of the factors identified in the field survey towards the causes of violations of human rights in police custody.

β-glucosidases from Aspergillus unguis NII 08123: Molecular characterization, properties and applications

Lignocellulosic biomass is probably the best alternative resource for biofuel production and it is composed mainly of cellulose, hemicelluloses and lignin. Cellulose is the most abundant among the three and conversion of cellulose to glucose is catalyzed by the enzyme cellulase. Cellulases are groups of enzymes act synergistically upon cellulose to produce glucose and comprise of endoglucanase, cellobiohydrolase and β-glucosidase. β -glucosidase assumes great importance due to the fact that it is the rate limiting enzyme. Endoglucanases (EG) produces nicks in the cellulose polymer exposing reducing and non reducing ends, cellobiohydrolases (CBH) acts upon the reducing or non reducing ends to liberate cellobiose units, and β - glucosidases (BGL) cleaves the cellobiose to liberate glucose completing the hydrolysis. . β -glucosidases undergo feedback inhibition by their own product- β glucose, and cellobiose which is their substrate. Few filamentous fungi produce glucose tolerant β - glucosidases which can overcome this inhibition by tolerating the product concentration to a particular threshold. The present study had targeted a filamentous fungus producing glucose tolerant β - glucosidase which was identified by morphological as well as molecular method. The fungus showed 99% similarity to Aspergillus unguis strain which comes under the Aspergillus nidulans group where most of the glucose tolerant β -glucosidase belongs. The culture was designated the strain number NII 08123 and was deposited in the NII culture collection at CSIR-NIIST. β -glucosidase multiplicity is a common occurrence in fungal world and in A.unguis this was demonstrated using zymogram analysis. A total 5 extracellular isoforms were detected in fungus and the expression levels of these five isoforms varied based on the carbon source available in the medium. Three of these 5 isoforms were expressed in higher levels as identified by the increased fluorescence (due to larger amounts of MUG breakdown by enzyme action) and was speculated to contribute significantly to the total _- β glucosidase activity. These isoforms were named as BGL 1, BGL3 and BGL 5. Among the three, BGL5 was demonstrated to be the glucose tolerant β -glucosidase and this was a low molecular weight protein. Major fraction was a high molecular weight protein but with lesser tolerance to glucose. BGL 3 was between the two in both activity and glucose tolerance.121 Glucose tolerant .β -glucosidase was purified and characterized and kinetic analysis showed that the glucose inhibition constant (Ki) of the protein is 800mM and Km and Vmax of the enzyme was found to be 4.854 mM and 2.946 mol min-1mg protein-1respectively. The optimumtemperature was 60°C and pH 6.0. The molecular weight of the purified protein was ~10kDa in both SDS as well as Native PAGE indicating that the glucose tolerant BGL is a monomeric protein.The major β -glucosidase, BGL1 had a pH and temperature optima of 5.0 and 60 °C respectively. The apparent molecular weight of the Native protein is 240kDa. The Vmax and Km was 78.8 mol min-1mg protein-1 and 0.326mM respectively. Degenerate primers were designed for glycosyl hydrolase families 1, 3 and 5 and the BGL genes were amplified from genomic DNA of Aspergillus unguis. The sequence analyses performed on the amplicons results confirmed the presence of all the three genes. Amplicon with a size of ~500bp was sequenced and which matched to a GH1 –BGL from Aspergillus oryzae. GH3 degenerate primers producing amplicons were sequenced and the sequences matched to β - glucosidase of GH3 family from Aspergillus nidulans and Aspergillus acculateus. GH5 degenerate primers also gave amplification and sequencing results indicated the presence of GH5 family BGL gene in the Aspergillus unguis genomic DNA.From the partial gene sequencing results, specific as well as degenerate primers were designed for TAIL PCR. Sequencing results of the 1.0 Kb amplicon matched Aspergillus nidulans β -glucosidase gene which belongs to the GH1 family. The sequence mainly covered the N-Terminal region of the matching peptide. All the three BGL proteins ie. BGL1, BGL3 and BGL5 were purified by chromatography an electro elution from Native PAGE gels and were subjected to MALDI-TOF mass spectrometric analysis. The results showed that BGL1 peptide mass matched to . β -glucosidase-I of Aspergillus flavus which is a 92kDa protein with 69% protein coverage. The glucose tolerant β -glucosidase BGL5 mass matched to the catalytic C-terminal domain of β -glucosidase-F from Emericella nidulans, but the protein coverage was very low compared to the size of the Emericella nidulans protein. While comparing the size of BGL5 from Aspergillus unguis, the protein sequence coverage is more than 80%. BGL F is a glycosyl hydrolase family 3 protein.The properties of BGL5 seem to be very unique, in that it is a GH3 β -glucosidase with a very low molecular weight of ~10kDa and at the same time having catalytic activity and glucose 122 tolerance which is as yet un-described in GH β -glucosidases. The occurrence of a fully functional 10kDA protein with glucose tolerant BGL activity has tremendous implications both from the points of understanding the structure function relationships as well as for applications of BGL enzymes. BGL-3 showed similarity to BGL1 of Aspergillus aculateus which was another GH3 β -glucosidase. It may be noted that though PCR could detect GH1, GH3 and GH5 β-glucosidases in the fungus, the major isoforms BGL1 BGL3 and BGL5 were all GH3 family enzymes. This would imply that β-glucosidases belonging to other families may also co-exist in the fungus and the other minor isoforms detected in zymograms may account for them. In biomass hydrolysis, GT-BGL containing BGL enzyme was supplemented to cellulase and the performances of blends were compared with a cocktail where commercial β- glucosidase was supplemented to the biomass hydrolyzing enzyme preparation. The cocktail supplemented with A unguis BGL preparation yielded 555mg/g sugar in 12h compared to the commercial enzyme preparation which gave only 333mg/g in the same period and the maximum sugar yield of 858 mg/g was attained in 36h by the cocktail containing A. unguis BGL. While the commercial enzyme achieved almost similar sugar yield in 24h, there was rapid drop in sugar concentration after that, indicating probably the conversion of glucose back to di-or oligosaccharides by the transglycosylation activity of the BGl in that preparation. Compared this, the A.unguis enzyme containing preparation supported peak yields for longer duration (upto 48h) which is important for biomass conversion to other products since the hydrolysate has to undergo certain unit operations before it goes into the next stage ie – fermentation in any bioprocesses for production of either fuels or chemicals.. Most importantly the Aspergillus unguis BGL preparation yields approximately 1.6 fold increase in the sugar release compared to the commercial BGL within 12h of time interval and 2.25 fold increase in the sugar release compared to the control ie. Cellulase without BGL supplementation. The current study therefore leads to the identification of a potent new isolate producing glucose tolerant β - glucosidase. The organism identified as Aspergillus unguis comes under the Aspergillus nidulans group where most of the GT-BGL producers belong and the detailed studies showed that the glucose tolerant β -glucosidase was a very low molecular weight protein which probably belongs to the glycosyl hydrolase family 3. Inhibition kinetic studies helped to understand the Ki and it is the second highest among the nidulans group of Aspergilli. This has promoted us for a detailed study regarding the mechanism of glucose tolerance. The proteomic 123 analyses clearly indicate the presence of GH3 catalytic domain in the protein. Since the size of the protein is very low and still its active and showed glucose tolerance it is speculated that this could be an entirely new protein or the modification of the existing β -glucosidase with only the catalytic domain present in it. Hydrolysis experiments also qualify this BGL, a suitable candidate for the enzyme cocktail development for biomass hydrolysis