Fluorescence characterization and gain studies on a dye-doped graded index polymer optical-fiber preform

Preparation of an appropriate optical-fiber preform is vital for the fabrication of graded-index polymer optical fibers (GIPOF), which are considered to be a good choice for providing inexpensive high bandwidth data links, for local area networks and telecommunication applications. Recent development of the interfacial gel polymerization technique has caused a dramatic reduction in the total attenuation in GIPOF, and this is one of the potential methods to prepare fiber preforms for the fabrication of dye-doped polymer-fiber amplifiers. In this paper, the preparation of a dye-doped graded-index poly(methyl methacrylate) (PMMA) rod by the interfacial gel polymerization method using a PMMA tube is reported. An organic compound of high-refractive index, viz., diphenyl phthalate (DPP), was used to obtain a graded-index distribution, and Rhodamine B (Rh B), was used to dope the PMMA rod. The refractive index profile of the rod was measured using an interferometric technique and the index exponent was estimated. The single pass gain of the rod was measured at a pump wavelength of 532 nm. The extent of doping of the Rh B in the preform was studied by axially exciting a thin slice of the rod with white light and measuring the spatial variation of the fluorescence intensity across the sample.

Spectral dependence of third order nonlinear optical susceptibility of zinc phthalocyanine

Wavelength dependence of saturable absorption (SA) and reverse saturable absorption (RSA) of zinc phthalocyanine was studied using 10 Hz, 8 ns pulses from a tunable laser, in the wavelength range of 520–686 nm, which includes the rising edge of the Q band in the electronic absorption spectrum. The nonlinear response is wavelength dependent and switching from RSA to SA has been observed as the excitation wavelength changes from the low absorption window region to higher absorption regime near the Q band. The SA again changes back to RSA when we further move over to the infrared region. Values of the imaginary part of third order susceptibility are calculated for various wavelengths in this range. This study is important in identifying the spectral range over which the nonlinear material acts as RSA based optical limiter.

Nonlinear optical absorption in silver nanosol

Nonlinear optical absorption in silver nanosol was investigated at selected wavelengths (456 nm, 477 nm and 532 nm) using open aperture Z-scan technique. It was observed that nature of nonlinear absorption is sensitively dependent on input fluence as well as on excitation wavelength. Besides, the present sample was found to exhibit reverse saturable absorption (RSA) and saturable absorption (SA) at these wavelengths depending on excitation fluence. RSA is attributed to enhanced absorption resulting from photochemical changes. SA observed for fluence values lower and higher than those corresponding to RSA are, respectively, attributed to plasmon bleach and saturation of RSA.

Nanosecond optical limiting response of sandwich-type neodymium dyphthalocyanine in a co-polymer host

The nanosecond optical limiting characteristics of sandwich-type neodymium diphthalocyanine in a co-polymer matrix of polymethyl methacrylate (PMMA) and methyl-2-cyanoacrylate have been studied for the first time. The measurements were performed using 9 ns laser pulses generated from a frequency-doubled Nd:YAG laser at 532 nm wavelength. The optical limiting performance of neodymium diphthalocyanine in co-polymer host was studied at different linear transmission. Laser damage threshold was also measured for the doped and undoped co-polymer samples. The optical limiting response is attributed to reverse saturable absorption which is due to excited-state absorption.

Enhanced luminescence and nonlinear optical properties of nanocomposites of ZnO–Cu

In this article, we present the spectral and nonlinear optical properties of ZnOCu nanocomposites prepared by colloidal chemical synthesis. The emission consisted of two peaks. The 385-nm ultraviolet (UV) peak is attributed to ZnO and the 550-nm visible peak is attributed to Cu nanocolloids. Obvious enhancement of UV and visible emission of the samples is observed and the strongest UV emission of a typical ZnOCu nanocomposite is over three times stronger than that of pure ZnO. Cu acts as a sensitizer and the enhancement of UV emission are caused by excitons formed at the interface between Cu and ZnO. As the volume fraction of Cu increases beyond a particular value, the intensity of the UV peak decreases while the intensity of the visible peak increases, and the strongest visible emission of a typical ZnOCu nanocomposite is over ten times stronger than that of pure Cu. The emission mechanism is discussed. Nonlinear optical response of these samples is studied using nanosecond laser pulses from a tunable laser in the wavelength range of 450650 nm, which includes the surface plasmon absorption (SPA) band. The nonlinear response is wavelength dependent and switching from reverse saturable absorption (RSA) to saturable absorption (SA) has been observed for Cu nanocolloids as the excitation wavelength changes from the low absorption window region to higher absorption regime near the SPA band. However, ZnO colloids and ZnOCu nanocomposites exhibit induced absorption at this wavelength. Such a changeover in the sign of the nonlinearity of ZnOCu nanocomposites, with respect to Cu nanocolloids, is related to the interplay of plasmon band bleach and optical limiting mechanisms. The SA again changes back to RSA when we move over to the infrared region. The ZnOCu nanocomposites show self-defocusing nonlinearity and good nonlinear absorption behavior. The nonlinear refractive index and the nonlinear absorption increases with increasing Cu volume fraction at 532 nm. The observed nonlinear absorption is explained through two-photon absorption followed by weak free-carrier absorption and interband absorption mechanisms. This study is important in identifying the spectral range and composition over which the nonlinear material acts as a RSA-based optical limiter. ZnOCu is a potential nanocomposite material for the light emission and for the development of nonlinear optical devices with a relatively small limiting threshold.

Spectral dependence of third order nonlinear optical susceptibility of zinc phthalocyanine

Wavelength dependence of saturable absorption (SA) and reverse saturable absorption (RSA) of zinc phthalocyanine was studied using 10 Hz, 8 ns pulses from a tunable laser, in the wavelength range of 520–686 nm, which includes the rising edge of the Q band in the electronic absorption spectrum. The nonlinear response is wavelength dependent and switching from RSA to SA has been observed as the excitation wavelength changes from the low absorption window region to higher absorption regime near the Q band. The SA again changes back to RSA when we further move over to the infrared region. Values of the imaginary part of third order susceptibility are calculated for various wavelengths in this range. This study is important in identifying the spectral range over which the nonlinear material acts as RSA based optical limiter.

Damage threshold determination of bulk polymer samples using pulsed photothermal deflection technique

Photothermal deflection technique was used for determining the laser damage threshold of polymer samples of teflon (PTFE) and nylon. The experiment was conducted using a Q-switched Nd-YAG laser operating at its fundamental wavelength (1-06μm, pulse width 10 nS FWHM) as irradiation source and a He-Ne laser as the probe beam, along with a position sensitive detector. The damage threshold values determined by photothermal deflection method were in good agreement with those determined by other methods.

High resolution optogalvanic study in nitrogen discharge

Doppler limited high resolution spectrum in the wavelength region 17224 to 17236 cm−1 of the first positive system (B 3Π g −A 3Σ u + ) of the N2 molecule is recorded by optogalvanic spectroscopic technique using a single mode ring dye laser. It is observed that the intensity and line width of the rotational line increase with the discharge current. Dependence of the collision broadening coefficient on the current was also evaluated.

Bioactivity Profile of Polyunsaturated Fattyacid extracts from Sardinella longiceps and Sardinella fimbriata – A comparative study

The oceans have proved to be an interminable source of new and effective drugs. Innumerable studies have proved that specific compounds isolated from marine organisms have great nutritional and pharmaceutical value. Polyunsaturated fattyacids (PUFA) in general are known for their dietary benefits in preventing and curing several critical ailments including Coronary heart disease (CHD) and cancers of various kinds. Eicosapentaenoic Acid (EPA) and Docosahexaenoic Acid (DHA) are two PUFA which are entirely marine in origin – and small Clupeoid fishes like sardines are known to be excellent sources of these two compounds. In this study, we selected two widely available Sardine species in the west coast, Sardinella longiceps and Sardinella fimbriata, for a comparative analysis of their bioactive properties. Both these sardines are known to be rich in EPA and DHA, however considerable seasonal variation in its PUFA content was expected and these variations studied. An extraction procedure to isolate PUFA at high purity levels was identified and the extracts obtained thus were studied for anti-bacterial, anti-diabetic and anti-cancerous properties.Samples of both the sardines were collected from landing centre, measured and their gut content analysed in four different months of the year – viz. June, September, December and March. The fish samples were analyzed for fattyacid using FAME method using gas chromatography to identify the full range of fattyacids and their respective concentration in each of the samples. The fattyacids were expressed in mg/g meat and later converted to percentage values against total fatty acids and total PUFA content. Fattyacids during winter season (Dec-Mar) were found to be generally higher than spawning season (June-Sept). PUFA dominated the profiles of both species and average PUFA content was also higher during winter. However, it was found that S. longiceps had proportionately higher EPA as compared to S. fimbriata which was DHA rich. Percentage of EPA and DHA also varied across months for both species – the spawning season seemed to show higher EPA content in S. longiceps and higher DHA content in S. fimbriata. Gut content analysis indicate that adult S. fimbriata is partial to zooplanktons which are DHA rich while adult S. longiceps feed mainly on EPA rich phytoplankton. Juveniles of both species, found mainly in winter, had a gut content showing more mixed diet. This difference in the feeding pattern reflect clearly in their PUFA profile – adult S. longiceps, which dominate the catch during the spawn season, feeding mostly on phytoplankton is concentrated with EPA while the juveniles which are found mostly in the winter season has slightly less EPA proportion as compared to adults. The same is true for S. fimbriata adults that are caught mostly in the spawning season; being rich in DHA as they feed mainly on zooplankton while the juveniles caught during winter season has a relatively lower concentration of DHA in their total PUFA.Various extraction procedures are known to obtain PUFA from fish oil. However, most of them do not give high purity and do not use materials indicated as safe. PUFA extracts have to be edible and should not have harmful substances for applying on mice and human subjects. Some PUFA extraction procedures, though pure and non-toxic, might induce cis-trans conversions during the extraction process. This conversion destroys the benefits of PUFA and at times is harmful to human body. A method free from these limitations has been standardized for this study. Gas Chromatography was performed on the extracts thus made to ensure that it is substantially pure. EPA: DHA ratios for both samples were derived - for S. longiceps this ratio was 3:2, while it was 3:8 for S. fimbriata.Eight common strains of gram positive and gram negative bacterial strains were subjected to the PUFA extracts from both species dissolved in acetone solution using Agar Well Diffusion method. The activity was studied against an acetone control. At the end of incubation period, zones of inhibition were measured to estimate the activity. Minimum inhibitory concentration for each of the active combinations was calculated by keeping p < 0.01 as significant. Four of the bacteria including multi-resistant Staphylococcus aureus were shown to be inhibited by the fish extracts. It was also found that the extracts from S. fimbriata were better than the one from S. longiceps in annihilating harmful bacteria.Four groups of mice subjects were studied to evaluate the antidiabetic properties of the PUFA extracts. Three groups were induced diabetes by administration of alloxan tetra hydrate. One group without diabetes was kept as control and another with diabetes was kept as diabetic control. For two diabetic groups, a prescribed amount of fish extracts were fed from each of the extracts. The biochemical parameters like serum glucose, total cholesterol, LDL & HDL cholesterol, triglycerides, urea and creatinine were sampled from all four groups at regular intervals of 7 days for a period of 28 days. It was found that groups fed with fish extracts had marked improvement in the levels of total LDL & HDL cholesterol, triglycerides and creatinine. Groups fed with extracts from S. fimbriata seem to have fared better as compared to S. longiceps. However, both groups did not show any marked improvement in blood glucose levels or levels of urea.Cell lines of MCF-7 (Breast Cancer) and DU-145 (Prostate Cancer) were used to analyse the cytotoxicity of the PUFA extracts. Both cell lines were subjected to MTT Assay and later the plates were read using an ELISA reader at a wavelength of 570nm. It was found that both extracts had significant cytotoxic effects against both cell lines and a peak cytotoxicity of 85-90% was apparent. IC50 values were calculated from the graphs and it was found that S. longiceps extracts had a slightly lower IC50 value indicating that it is toxic even at a lower concentration as compared to extracts from S. fimbriata.This study summarizes the bioactivity profile of PUFA extracts and provides recommendation for dietary intake; fish based nutritional industry and indigenous pharmaceutical industry. Possible future directions of this study are also elaborated.

Metglas thin film based magnetostrictive transducers for use in long period fibre grating sensors

Metallic glass alloy Metglas 2826 MB based amorphous magnetic thin films were fabricated by the thermal evaporation technique. Transmission electron micrographs and electron diffraction pattern showed the amorphous nature of the films. Composition of the films was analyzed employing X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy techniques. The film was integrated to a long period fibre grating. It was observed that the resonance wavelength of the fibre grating decreased with an increase in the magnetic field. Change in the resonance wavelength was minimal at higher magnetic fields. Field dependent magnetostriction values revealed the potential application of these films in magnetostrictive sensor devices.

Acoustic radiation and scattering from cylindrical bodies and analysis of transducer arrays

New mathematical methods to analytically investigate linear acoustic radiation and scattering from cylindrical bodies and transducer arrays are presented. Three problems of interest involving cylinders in an infinite fluid are studied. In all the three problems, the Helmholtz equation is used to model propagation through the fluid and the beam patterns of arrays of transducers are studied. In the first problem, a method is presented to determine the omni-directional and directional far-field pressures radiated by a cylindrical transducer array in an infinite rigid cylindrical baffle. The solution to the Helmholtz equation and the displacement continuity condition at the interface between the array and the surrounding water are used to determine the pressure. The displacement of the surface of each transducer is in the direction of the normal to the array and is assumed to be uniform. Expressions are derived for the pressure radiated by a sector of the array vibrating in-phase, the entire array vibrating in-phase, and a sector of the array phase-shaded to simulate radiation from a rectangular piston. It is shown that the uniform displacement required for generating a source level of 220 dB ref. μPa @ 1m that is omni directional in the azimuthal plane is in the order of 1 micron for typical arrays. Numerical results are presented to show that there is only a small difference between the on-axis pressures radiated by phased cylindrical arrays and planar arrays. The problem is of interest because cylindrical arrays of projectors are often used to search for underwater objects. In the second problem, the errors, when using data-independent, classical, energy and split beam correlation methods, in finding the direction of arrival (DOA) of a plane acoustic wave, caused by the presence of a solid circular elastic cylindrical stiffener near a linear array of hydrophones, are investigated. Scattering from the effectively infinite cylinder is modeled using the exact axisymmetric equations of motion and the total pressures at the hydrophone locations are computed. The effect of the radius of the cylinder, a, the distance between the cylinder and the array, b, the number of hydrophones in the array, 2H, and the angle of incidence of the wave, α, on the error in finding the DOA are illustrated using numerical results. For an array that is about 30 times the wavelength and for small angles of incidence (α<10), the error in finding the DOA using the energy method is less than that using the split beam correlation method with beam steered to α; and in some cases, the error increases when b increases; and the errors in finding the DOA using the energy method and the split beam correlation method with beam steered to α vary approximately as a7 / 4 . The problem is of interest because elastic stiffeners – in nearly acoustically transparent sonar domes that are used to protect arrays of transducers – scatter waves that are incident on it and cause an error in the estimated direction of arrival of the wave. In the third problem, a high-frequency ray-acoustics method is presented and used to determine the interior pressure field when a plane wave is normally incident on a fluid cylinder embedded in another infinite fluid. The pressure field is determined by using geometrical and physical acoustics. The interior pressure is expressed as the sum of the pressures due to all rays that pass through a point. Numerical results are presented for ka = 20 to 100 where k is the acoustic wavenumber of the exterior fluid and a is the radius of the cylinder. The results are in good agreement with those obtained using field theory. The directional responses, to the plane wave, of sectors of a circular array of uniformly distributed hydrophones in the embedded cylinder are then computed. The sectors are used to simulate linear arrays with uniformly distributed normals by using delays. The directional responses are compared with the output from an array in an infinite homogenous fluid. These outputs are of interest as they are used to determine the direction of arrival of the plane wave. Numerical results are presented for a circular array with 32 hydrophones and 12 hydrophones in each sector. The problem is of interest because arrays of hydrophones are housed inside sonar domes and acoustic plane waves from distant sources are scattered by the dome filled with fresh water and cause deterioration in the performance of the array.

Beam shaping of sectoral electromagnetic horn antennas using corner reflector technique

In the present thesis, possibility of beam shaping of sectoral horns and corner reflector systems'has been studied in detail. The experimental results obtained in the above two cases are compared. As far as the flanged sectoral horns are concerned, the special advantage is that the gain is increased without impairing impedance conditions. An intense study on corner reflector antennas shows that the been broadening or focussing will be possible by adjusting parameters involved. Beam tilting by imposing asymmetries is another interesting property of the systems. A comprehensive study of these fields has been presented in Chapter II. Chapter III is exclusively for describing the experimental techniques used in the present investigation. In Chapter IV, experimental results on flanged sectoral horns and corner reflector eyetses are presented. A comparative analysis of the experimental results obtained with flanged sectoral horns and corner reflector systems is presented in the Chapter V. The similarity and close resemblance in each aspects are shown by presenting typical results from these two eysteee. Theoretical aspects of both types of antennas are considered in Chapter VI. Attempts are made for co-ordinating the theoretical aspects and drawing a final conclusion. In Chapter VII. the final conclusion that the flanged sectoral horn may be considered as a corner reflector system has been drawn. The importance of the conclusions and usefulness are pointed out. The scope for further work in these lines has been indicated.

Development of optical fiber sensors for selected chemical and physical sensing applications

The objective of the preset work is to develop optical fiber sensors for various physical and chemical parameters. As a part of this we initially investigated trace analysis of silica, ammonia, iron and phosphate in water. For this purpose the author has implemented a dual wavelength probing scheme which has many advantages over conventional evanescent wave sensors. Dual wavelength probing makes the design more reliable and repeatable and this design makes the sensor employable for concentration, chemical content, adulteration level, monitoring and control in industries or any such needy environments. Use of low cost components makes the system cost effective and simple. The Dual wavelength probing scheme is employed for the trace analysis of silica, iron, phosphate, and ammonia in water. Such sensors can be employed for the steam and water quality analysers in power plants. Few samples from a power plant are collected and checked the performance of developed system for practical applications.

Development and parametric studies of pulsed nitrogen and d-switched nd:glass lasers and some of their applications

Laser engineering is an area in which developments in the existing design concepts and technology appear at an alarming rate. Now—a-days, emphasis has shifted from innovation to cost reduction and system improvement. To a major extent, these studies are aimed at attaining larger power densities, higher system efficiency and identification of new lasing media and new lasing wavelengths. Todate researchers have put to use all the ditferent Forms of matter as lasing material. Laser action was observed For the first time in a gaseous system - the He-Ne system. This was Followed by a variety of solidstate and gas laser systems. Uarious organic dyes dissolved in suitable solvents were found to lase when pumped optically. Broad band emission characteristics of these dye molecules made wavelength tuning possible using optical devices. Laser action was also observed in certain p-n junctions of semiconductor materials and some of these systems are also tunable. The recent addition to this list was the observation of laser action from certain laser produced plasmas. The purpose of this investigation was to examine the design and Fabrication techniques of pulsed Nitrogen lasers and high power Nd: Glass laserso Attempt was also made to put the systems developed into certain related experiments

Application of ocean colour data to study the oceanographic and atmospheric features off the southwest coast of India with special reference to upwelling

Satellite remote sensing is being effectively used in monitoring the ocean surface and its overlying atmosphere. Technical growth in the field of satellite sensors has made satellite measurement an inevitable part of oceanographic and atmospheric research. Among the ocean observing sensors, ocean colour sensors make use of visible band of electromagnetic spectrum (shorter wavelength). The use of shorter wavelength ensures fine spatial resolution of these parameters to depict oceanographic and atmospheric characteristics of any region having significant spaio-temporal variability. Off the southwest coast of India is such an area showing very significant spatio-temporal oceanographic and atmospheric variability due to the seasonally reversing surface winds and currents. Consequently, the region is enriched with features like upwelling, sinking, eddies, fronts, etc. Among them, upwelling brings nutrient-rich waters from subsurface layers to surface layers. During this process primary production enhances, which is measured in ocean colour sensors as high values of Chl a. Vertical attenuation depth of incident solar radiation (Kd) and Aerosol Optical Depth (AOD) are another two parameters provided by ocean colour sensors. Kd is also susceptible to undergo significant seasonal variability due to the changes in the content of Chl a in the water column. Moreover, Kd is affected by sediment transport in the upper layers as the region experiences land drainage resulting from copious rainfall. The wide range of variability of wind speed and direction may also influence the aerosol source / transport and consequently AOD. The present doctoral thesis concentrates on the utility of Chl a, Kd and AODprovided by satellite ocean colour sensors to understand oceanographic and atmospheric variability off the southwest coast of India. The thesis is divided into six Chapters with further subdivisions