Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.

Feeding whole grain with pelleted diets to growing broiler chickens

Selostus: Kokojyväviljan syöttäminen broilereille rakeisen rehun seassa

Whole sales market for fresh potato in Finland

Selostus: Suomen ruokaperunamarkkinoiden toimivuus

Monitoimipystysorvin NC- ohjelmoinnin kehittäminen CAM käyttöönotolla

Diplomityön tavoitteena oli tehostaa venttiilipesien koneistuksessa käytettävän monitoimipystysorvin NC - ohjelmointia CAM - ohjelman käyttöönotolla. Tutkimus on osa laajempaa kokonaisuutta liittyen koneistusalihankinnan kehittämiseen ja yrityksen kilpailukyvyn ylläpitoon ja parantamiseen liiketoiminta-alueella, jolla on tällä hetkellä hyvät kasvunäkymät. Tavoite rajattiin yritykseen jo aiemmin hankitun WinCAM - ohjelman päivittämiseen ja hyödyntämiseen monitoimipystysorvin NC - ohjelmoinnissa. Tutkimuksen käytännön tavoitteena oli selvittää CAM - ohjelmoinnin käyttömahdollisuudet, sekä luoda CAM - ohjelmistoon pohjautuva, räätälöity NC - ohjelmointikonsepti pilottikohteeseen. Tutkimuksen kokeellisen osuuden muodostivat tällöin nykyisen tuotannon ongelmakohtien löytäminen, koneen ohjelmointitarpeiden kartoitus,sekä menetelmäkehitys. Tutkimuksen päämääränä oli tuotannon tasolla käytettävä järjestelmä, jolla koneen ohjelmointi olisi mahdollista myös vähemmällä konekohtaisella kokemuksella. Nykyisen toimintatavan ongelmina olivat yhtenäisen NC - ohjelmointikäytännön puute, niin valmiiden ohjelmien käytössä kuin uusienkin ohjelmien tekemisessä. Tähän olivat syynä NC - ohjauksen heikko käytettävyys erityisesti sorvauksen osalta. Nämä tekijät yhdistettynä monitoimityöstökoneessa tarvittavaan koordinaatiston hallintaan vaikeuttivat ohjelmointia. Työntekijäkohtaiset erot NC - ohjelmien käytössä, sekä laadultaan vaihtelevat valuaihiot aiheuttivat tuotannon läpäisyaikaan merkittävää vaihtelua. Siten myös koneen kuormituksen säätely oli vaikeaa. Uuden ohjelmointikonseptin toteutuksessa pidettiin etusijalla hyvää käytettävyyttä, sekä uuden menetelmän aukotonta liittymistä olemassa oleviin tuotantojärjestelmiin. Ohjelmointikonseptin toteutuksessa, osaperheestä haettiin selkeästi parametroitaviksi soveltuvat työvaiheet, jotka voitiin hallita yleiskäyttöisillä aliohjelmilla. Tuotteiden muidengeometrioiden hallintaan laadittiin geometriakirjasto, jota voitiin käyttää tavanomaisen graafisen ohjelmoinnin pohjana. Vanhaa toimintatapaa ja diplomityön aikana kehitettyä CAM - ohjelmointijärjestelmää vertailtiin perustuen NC - ohjelmien tehokkuuteen, jota tarkasteltiin saman työvaiheen työstöaikaan perustuen. Tämän lisäksi tärkeän tuloksen muodostavat myös kvalitatiivisetseikat, jotka liittyvät ohjelmointiympäristön käytettävyyteen. CAM - ohjelmoinnin kehittäminen ja käyttöönotto pilottikohteessa sujui pääosin hyvin ja laaditunsuunnitelman mukaisesti. Aiemmin hankalasti ohjelmoitavat työvaiheet, kuten erilaisten laippatasopintojen ja reikäpiirien ohjelmointi muutettiin makrokäyttöön soveltuviksi. Sorvauksessa ongelmia aiheuttaneen tiivistelilan koneistukseen sovellettiin graafista ohjelmointia. Koko tuotannon mittakaavassa NC - ohjelmoinninosuus oli kuitenkin vähäinen, mistä johtuen koneen tuottavuuteen ei tutkimuksenajanjaksolla voitu vaikuttaa. Sen sijaan tuotannon sujuvuuteen oleellisesti vaikuttavaa työtekijöiden 'hiljaisen tiedon' määrää voitiin vähentää vakioimalla ohjelmointia ja siirtämällä tehokkaiksi havaitut menetelmät ohjelmointijärjestelmään.

Fouling, prevention of fouling, and clearing in filtration

In this thesis fouling of conventional filter fabrics and membranes was studied. In the beginning of the thesis fouling and how it can be measured and predicted is reviewed. Information on different methods on how fouling canbe decreased or cleaned away is also given. The experimental part is divided into two sections; fabric filtration and membrane filtration. Fouling of the filter fabrics was studied with silica or cupper slurries and fouling of the membranes was studied with pulp and paper mill waters. The fouled filter materials were characterised according to many different methods. The most useful way to observe fouling is to measure the changes in the permeate flux. Fouling can also be seen visually e.g. with scanning electron microscopy. Consequently, also the reason for the fouling in question might be found. Different filtration characteristics affect fouling e.g. as the filtration pressure was increased it did not have much influence on the permeate flux, but the pressure caused the membrane to get fouled faster. Also, an increase of shear rate on the membrane surface decreased fouling. Different pretreatment methods for the effluent were tested in membrane filtration to decrease fouling. The tested methods; biological treatment, ozonation, enzymatic treatment and flocculation, did not have a clear influence on the fouling of the membrane, but e.g. a biological treatment combined with ultrafiltration made the tested groundwood mill circulation water purer than ultrafiltration alone.

A Large-Sized Multiwire Proportional Counter for Radiological Survey of Large Areas and Surfaces

Työn tavoitteena oli selvittää, miten eri parametrit vaikuttavat monilankaisen verrannollisuuslaskurin laskennallisiin ominaisuuksiin sekä voidaanko suurikokoista monilankaverrannollisuuslaskuria käyttää tehokkaasti suurien pintojen ? - ja ?- kontaminaation mittaamiseen. Ensin selvitettiin EU:n nykyistä clearing-käytäntöä sekä hahmoteltiin tulevia materiaalivirtoja, esiteltiin verrannollisuuslaskurin ja sen monilankamallin toimintaperiaate sekä käytettävien materiaalien ominaisuudet. Kootun teorian pohjalta selvitettiin tärkeimpien parametrien vaikutus ilmaisimen laskennallisiin ominaisuuksiin. Lopuksi suoritettiin rakenteilla olevan monilankaverrannollisuuslaskurin alustava testaus. Tulevien vuosien aikana eri puolilla maailmaa suljettavat erityyppiset ydinlaitokset luovat suuren tarpeen tehokkaiden kontaminaatiomittauslaitteistojen kehittämiselle. Tällä hetkellä mittaukset suoritetaan lähinnä noin 1 dm2 käsi-instrumentein, joten suurikokoinen, automatisoitu mittauslaitteisto sekä tehostaisi mittausprosessia suuresti sekä säästäisi runsaasti miestyötunteja. Jatkotoimenpiteiksi ehdotetaan laitteiston jatkotestausta, liikkeen ja nopeuden testausta sekä lopulta paikkaherkkyystoiminnon toteuttamisperiaatteen valintaa ja testausta.

Paikallisilmanvaihdon toimivuus baaritiskillä työntekijöiden tupakansavualtistuksen vähentämisessä

Työssä tarkasteltiin tupakkalain vaikutuksia ravintoloiden ilmanvaihtoon ja työntekijöiden tupakansavulle altistumiseen. Lisäksi tutkittiin, mitä muita määräyksiä Suomessa ja muualla on ravintoloiden ilmanvaihdosta ja minkälaisin ilmanvaihdollisin menetelmin voidaan ravintolatyöntekijöiden altistumista tupakansavulle vähentää. Kokeellisena osana tutkittiin Halton Oy:n kehittämän baaritiskin paikallisilmanvaihtojärjestelmän suojaustehokkuutta ja toimivuutta suomalaisessa yökerhossa. Järjestelmään kuului kattoon sijoitettu kohdepuhallus ja baaripöytään sijoitettu ilmaverholaitteisto. Mittaukset suoritettiin käytännön olosuhteissa toimivassa ravintolassa. Mitattuina suureina olivat sisäilman nikotiini- ja hiukkaspitoisuus työskentelyalueella ja asiakkaiden oleskeluvyöhykkeellä. Lisäksi käytettiin merkkiainemenetelmää tupakansavun leviämisen seuraamiseen. Saavutettu suojaustehokkuus oli mittaustavasta ja tilanteesta riippuen 72-95%. Mittaukset osoittivat, että tutkitulla paikallisilmanvaihtoratkaisulla voitiin hyvin oleellisesti vähentää ympäristön tupakansavun kulkeutumista työntekijöiden hengitysvyöhykkeelle. Paikallisilmanvaihto on kuitenkin toteutettava osana koko ravintolan ilmanvaihtoa ja säädettävä oikein hyvän tuloksen saavuttamiseksi.

Phylogeography and population genetics of north European Atlantic salmon (Salmo salar L.)

Although abundant in the number of individuals, the Atlantic salmon may be considered as a threatened species in many areas of its native distribution range. Human activities such as building of power plant dams, offshore overfishing, pollution, clearing of riverbeds for timber floating and badly designed stocking regimes have diminished the distribution of Atlantic salmon. As a result of this, many of the historical populations both in Europe and northern America have gone extinct or are severely depressed. In fact, only 1% of Atlantic salmon existing today are of natural origin, the rest being farmed salmon. All of this has lead to a vast amount of research and many restoration programmes aiming to bring Atlantic salmon back to rivers from where it has vanished. However, many of the restoration programmes conducted thus far have been unsuccessful due to inadequate scientific research or lack of its implementation, highlighting the fact that more research is needed to fully understand the biology of this complex species. The White and Barents Seas in northwest Russia are among the last regions in Europe where Atlantic salmon populations are still stable, thus forming an important source of biodiversity for the entire European region. Salmon stocks from this area are also of immense economic and social importance for the local people in the form of fishing tourism. The main aim of this thesis was to elucidate the post-glacial history and population genetic structure of north European and particularly northwest Russian Atlantic salmon, both of which are aspects of great importance for the management and conservation of the species. Throughout the whole thesis, these populations were studied by utilizing microsatellites as the main molecular tool. One of the most important discoveries of the thesis was the division of Atlantic salmon from the White and Barents Seas into four separate clusters, which has not been observed in previous studies employing nuclear markers although is supported by mtDNA studies. Populations from the western Barents Sea clustered together with the northeast Atlantic populations into a clearly distinguishable group while populations from the White Sea and eastern Barents Sea were separated into three additional groups. This has important conservation implications as this thesis clearly indicates that conservation of populations from all of the observed clusters is warranted in order to conserve as much of the genetic diversity as possible in this area. The thesis also demonstrates how differences in population life histories within a species, migratory behaviour in this case, and in their phylogeographic origin affect the genetic characteristics of populations, namely diversity and divergence levels. The anadromous populations from the Atlantic Ocean, White Sea and Barents Sea possessed higher levels of genetic diversity than the anadromous populations form the Baltic Sea basin. Among the non-anadromous populations the result was the opposite: the Baltic freshwater populations were more variable. This emphasises the importance of taking the life history of a population into consideration when developing conservation strategies: due to the limited possibilities for new genetic diversity to be generated via gene flow, it is expected that freshwater Atlantic salmon populations would be more vulnerable to extinction following a population crash and thus deserve a high conservation status. In the last chapter of this thesis immune relevant marker loci were developed and screened for signatures of natural selection along with loci linked to genes with other functions or no function at all. Also, a novel landscape genomics method, which combines environmental information with molecular data, was employed to investigate whether immune relevant markers displayed significant correlations to various environmental variables more frequently than other loci. Indications of stronger selection pressure among immune-relevant loci compared to non-immune relevant EST-linked loci was found but further studies are needed to evaluate whether it is a common phenomenon in Atlantic salmon.

Clinically occult metastases in patients with cutaneous melanoma. Detection with sentinel lymph node biopsy and whole body positron emission tomography

Objective: The aim of this study was to investigate the use of sentinel lymph node biopsy (SLNB) and whole body positron emission tomography (PET), with emphasis on surgical treatment and prognosis, in the detection of clinically occult metastases in patients with clinically localized cutaneous melanoma. Patients and methods: The study population consisted of 1255 patients with clinical stage I–II cutaneous melanoma, operated at Turku University Hospital between 1983 and 2007. 334 patients underwent SLNB and they were compared to 921 retrospective patients. A subgroup of 30 symptom-free patients with high risk melanoma underwent prospectively whole body PET 6–24 months postoperatively. Results: Overall, the disease-specific survival rate was 84.4 % at five years. Sex, Breslow thickness, age and nodal status were independent prognostic factors for survival. SLNB revealed occult nodal metastases in 17 % of the patients. There was no significant difference in disease-specific overall survival between SLNB patients and controls, but the nodal disease-free time was significantly longer suggesting better local control after SLNB and subsequent completion lymph node dissection. The followup time was different between the study cohorts and initial surgery was performed during different time periods. SLNB detected micrometastases in seven of 155 patients (4.5 %) with thin T1 primary melanoma and in four of 25 patients (16 %) with head and neck melanoma. In six of 30 asymptomatic patients with high risk melanoma (20 %), whole body PET detected occult distant metastases. Conclusion: Both SLNB and whole body PET were reliable methods to detect clinically occult metastases in patients with cutaneous melanoma. This upstaging altered the treatment in each case.

Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.

Project Master Document adaption in order fulfillment process

This thesis discusses adaption of new project management tool at ABB Oy Motors and Generators business unit, Synchronous Machines profit centre. Thesis studies project modeling in general and buries in the Gate Model used at ABB Synchronous Machines. It is essential to understand Gate Model because this new project management tool, called Project Master Document, is created on the base of the existing project model. Thesis also analyzes goals and structure of Project Master Document in order to ease implementation of this new tool. Project Master Document aims to improved customer order fulfillment by clearing order handover interface. Office process, especially responsibilities and target dates, become also clearer after Master Document implementation. The document is built to be frame for whole order fulfillment process including check points for each gate of project model and updated memos from all project meetings. Furthermore, project progress will be clearly stated by status markings and visualized with colors.