Relay card for capacitance measurements

In this bachelor's thesis a relay card for capacitance measurements was designed, built and tested. The study was made for the research and development laboratory of VTI Technologies, which manufactures capacitive silicon micro electro mechanical accelerometers and pressure sensors. As the size of the sensors is decreasing the capacitance value of the sensors also decreases. The decreased capacitance causes a need for new and more accurate measurement systems. The technology used in the instrument measuring the capacitance dictates a framework how the relay card should be designed, thus the operating principle of the instrument must be known. To achieve accurate results the measurement instrument and its functions needed to be used correctly. The relay card was designed using printed circuit board design methods that minimize interference coupling to the measurement. The relay card that was designed in this study is modular. It consists of a separate CPU card, which was used to control the add-on cards connected to it. The CPU card was controlled from a computer through a serial bus. Two add-on cards for the CPU card were designed in this study. The first one was the measurement card, which could be used to measure 32 capacitive sensors. The second add-on card was the MUX card, which could be used to switch between two measurement cards. The capacitance measurements carried out through the MUX card and the measurement cards were characterized with a series of test measurements. The test measurement data was then analysed. The relay card design was confirmed to work and offer accurate measurement results up to a measurement frequency of 10 MHz. The length of the measurement cables limited the measurement frequency.

Standardisation process of Universal Mobile Telecommunication System in Third Generation Partnership Project

Third Generation Partnership Project (3GPP) on organisaatio, joka määrittelee ja ylläpitää kolmannen sukupolven matkapuhelinverkon standardeja. Organisaatio luotiin monien eri standardointielinten toimesta havaittaessa, ettei maailmanlaajuista kolmannen sukupolven matkapuhelinteknologiaa voitaisi määritellä ilman laajaa yhteistyötä. 3GPP:ssä standardointityö on jakautunut usealle tekniselle määrittelyryhmälle. Jokaisen ryhmän tehtävänä on kehittää määrittelyjä ja raportteja omalla vastuualueellaan. 3GPP:ssä määrittelytyötä tehdään samanaikaisesti teknillisten määrittelyryhmien välillä. Tämä vaatii tiukkoja sääntöjä määrittelyjen luonti-, hyväksyntä- ja ylläpitotehtäviin. Vain siten on mahdollista hallita määrittelyihin tulevia muutoksia ja tarvittavaa kokonaistyömäärää. Tämä diplomityö kuvaa 3GPP:n määrittelemän UMTS-teknologian. Työssä keskitytään tarkemmin 3GPP-organisaation rakenteeseen, määritysten tekemiseen ja työskentelytapoihin. Tämä diplomityö osoittaa millainen organisaatio ja säännöt vaaditaan maailmanlaajuisen matkapuhelinjärjestelmän kehittämiseen.

Protestant Churches and the making of the Universal Declaration of Human Rights

Kirjallisuusarvostelu

Energian talteenotto liikkuvassa raskaassa työkoneessa

Tämä työ on osa Integrated Serial and Parallel Hybrid Drives in Working Machines projektia. Työssä simuloidaan ja lasketaan energian palautuspotentiaalia raskaassa liikkuvassa työkoneessa. Työn alussa aihetta käsitellään yleisesti kirjallisuuskatsauksen muodossa. Tukkikurottaja valittiin simulointien ja laskennan kohteeksi. Työssä suoritettiin alustavat simuloinnit, joiden tarkoituksena oli varmistua, että palautettavaa energiaa on olemassa. Tulokset osoittavat, että energian palauttaminen on mahdollista. Mittaukset ovat osa työtä. Mitatut muuttujat ovat paineet ja pituudet hydraulisylintereistä, rungon kiihtyvyys, sekä kaikki CAN-väylään kytkettyjen antureiden mittaustiedot. Lopulliset simuloinnit perustuvat mitattuihin työkiertoihin. Työsylintereiden ja ajovoimansiirron tehotarpeet valittiin simulointien tarkasteltaviksi mittaussuureiksi. Mahdollinen palautettavan energian määrä eri työkierroissa on työn lopputulos. Tulokset osoittavat, että palautettavan energian määrä on talteenoton kannalta riittävä.

Building object-oriented software with the D-Bus messaging system

Object-oriented programming is a widely adopted paradigm for desktop software development. This paradigm partitions software into separate entities, objects, which consist of data and related procedures used to modify and inspect it. The paradigm has evolved during the last few decades to emphasize decoupling between object implementations, via means such as explicit interface inheritance and event-based implicit invocation. Inter-process communication (IPC) technologies allow applications to interact with each other. This enables making software distributed across multiple processes, resulting in a modular architecture with benefits in resource sharing, robustness, code reuse and security. The support for object-oriented programming concepts varies between IPC systems. This thesis is focused on the D-Bus system, which has recently gained a lot of users, but is still scantily researched. D-Bus has support for asynchronous remote procedure calls with return values and a content-based publish/subscribe event delivery mechanism. In this thesis, several patterns for method invocation in D-Bus and similar systems are compared. The patterns that simulate synchronous local calls are shown to be dangerous. Later, we present a state-caching proxy construct, which avoids the complexity of properly asynchronous calls for object inspection. The proxy and certain supplementary constructs are presented conceptually as generic object-oriented design patterns. The e ect of these patterns on non-functional qualities of software, such as complexity, performance and power consumption, is reasoned about based on the properties of the D-Bus system. The use of the patterns reduces complexity, but maintains the other qualities at a good level. Finally, we present currently existing means of specifying D-Bus object interfaces for the purposes of code and documentation generation. The interface description language used by the Telepathy modular IM/VoIP framework is found to be an useful extension of the basic D-Bus introspection format.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

Mannesmann-Mulag-universal kippvagn muk

kuv., 24 x 16 cm

Multi-axis solutions in packaging machines in Europe

The objective of this thesis was to examine the potential of multi-axis solutions in packaging machines produced in Europe. The definition of a multi-axis solution in this study is a construction that uses a common DC bus power supply for different amplifiers running the axes and the intelligence is centralized into one unit. The cost structure of a packaging machine was gained from an automation research, which divided the machines according to automation categories. The automation categories were then further divided into different sub-components by evaluating the ratio of multi-axis solutions compared to other automation components in packaging machines. A global motion control study was used for further information. With the help of the ratio, an estimation of the potential of multi-axis solutions in each country and packaging machine sector was completed. In addition to the research, a specific questionnaire was sent to five companies to gain information about the present situation and possible trends in packaging machinery. The greatest potential markets are in Germany and Italy, which are also the largest producers of packaging machinery in Europe. The greatest growth in the next few years will be seen in Turkey where the annual growth rate equals the general machinery production rate in Asia. The greatest market potential of the Nordic countries is found in Sweden in 35th position on the list. According to the interviews, motion control products in packaging machines will retain their current power levels, as well as the number of axes in the future. Integrated machine safety features together with a universal programming language are the desired attributes of the future. Unlike generally in industry, the energy saving objectives are and will remain insignificant in the packaging industry.

Acquisition target selection of a serial acquirer : case KONE Oyj

Acquisitions are a way for a company to grow, enter new geographical areas, buy out competition or diversify. Acquisitions have recently grown in both size and value. Despite of this, only approximately 25 percent of acquisitions reach their targets and goals. Companies making serial acquisitions seem to be exceptionally successful and succeed in the majority of their acquisitions. The main research question this study aims to answer is: “What issues impact the selection of acquired companies from the point of view of a serial acquirer? The main research question is answered through three sub questions: “What is a buying process for a serial acquirer like?”, “What are the motives for a serial acquirer to buy companies?” and “What is the connection between company strategy and serial acquisitions?”. The case company KONE is a globally operating company which mainly produces and maintains elevators and escalators. Its headquarter is located in Helsinki, Finland. The company has a long history of making acquisitions and does 20- 30 acquisitions a year. By a key person interview, the acquisition process of the case company is compared with the literature about successful serial acquirers. The acquisition motives in this case are reflected upon three of the acquisition motive theories by Trautwein: efficiency theory, monopoly theory and valuation theory. The linkage between serial acquisitions and company strategy is studied through the key person interview. The main research findings are that the acquisition process of KONE is compatible with a successful acquisition process recognized in literature (RAID). This study confirms the efficiency theory as an acquisition motive and more closely the operational synergies. The monopoly theory can only vaguely be supported by this study, but cannot be totally rejected because of the structure of the industry. The valuation theory does not get any support in this study and can therefore be rejected. The linkage between company strategy and serial acquisitions is obvious and making acquisitions can be seen as growth strategy and a part of other company strategies.

Bus bar aeolian vibration field tests

Large amplitude bus bar aeolian vibration may lead to post insulator damage. Different damping applications are used to decrease the risk of large amplitude aeolian vibration. In this paper the post insulator load caused by the bus bar aeolian vibration and the effect of damping methods are evaluated. The effects of three types of bus bar connectors and three types of primary structures are studied. Two actual damping devices, damping cable and their combinations are studied. The post insulator loads are studied with strain gage based custom made force sensors installed on the both ends of the post insulator and with the displacement sensor installed on the midpoint of the bus bar. The post insulator loads are calculated from the strain values and the damping properties are determined from the displacement history. The bus bar is deflected with a hanging weight. The weight is released and the bus bar is left to free damped vibration. Both actual bus bar vibration dampers RIBE and SBI were very effective against the aeolian vibration. Combining vibration damper with damping cable will increase the damping ratio but it may be unnecessary considering the extra effort. Bus bar connector type or primary structure have no effect on the vertical load. The bending moment at the post insulator with double sided bus bar connector is significantly higher than at the post insulator with single sided bus bar connector. No reliable conclusions about bus bar connector type effect can be done, but the roller bearing type or central bearing type connector may reduce the bending moment. The RHS steel frame as primary structure may increase the bending moment peak values since it is the least rigid primary structure type and it may start to vibrate as a response to the awakening force of the vibrating bus bar.

Universal Quantum Cloning

After introducing the no-cloning theorem and the most common forms of approximate quantum cloning, universal quantum cloning is considered in detail. The connections it has with universal NOT-gate, quantum cryptography and state estimation are presented and briefly discussed. The state estimation connection is used to show that the amount of extractable classical information and total Bloch vector length are conserved in universal quantum cloning. The 1  2 qubit cloner is also shown to obey a complementarity relation between local and nonlocal information. These are interpreted to be a consequence of the conservation of total information in cloning. Finally, the performance of the 1  M cloning network discovered by Bužek, Hillery and Knight is studied in the presence of decoherence using the Barenco et al. approach where random phase fluctuations are attached to 2-qubit gates. The expression for average fidelity is calculated for three cases and it is found to depend on the optimal fidelity and the average of the phase fluctuations in a specific way. It is conjectured to be the form of the average fidelity in the general case. While the cloning network is found to be rather robust, it is nevertheless argued that the scalability of the quantum network implementation is poor by studying the effect of decoherence during the preparation of the initial state of the cloning machine in the 1 ! 2 case and observing that the loss in average fidelity can be large. This affirms the result by Maruyama and Knight, who reached the same conclusion in a slightly different manner.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.