Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Performance Degradation Modelling and Techno-Economic Analysis of Lithium-Ion Battery Energy Storage Systems

Transmission system operators and distribution system operators are experiencing new challenges in terms of reliability, power quality, and cost efficiency. Although the potential of energy storages to face those challenges is recognized, the economic implications are still obscure, which introduce the risk into the business models. This thesis aims to investigate the technical and economic value indicators of lithium-ion battery energy storage systems (BESS) in grid-scale applications. In order to do that, a comprehensive performance lithium-ion BESS model with degradation effects estimation is developed. The model development process implies literature review on lifetime modelling, use, and modification of previous study progress, building the additional system parts and integrating it into a complete tool. The constructed model is capable of describing the dynamic behavior of the BESS voltage, state of charge, temperature and capacity loss. Five control strategies for BESS unit providing primary frequency regulation are implemented, in addition to the model. The questions related to BESS dimensioning and the end of life (EoL) criterion are addressed. Simulations are performed with one-month real frequency data acquired from Fingrid. The lifetime and cost-benefit analysis of the simulation results allow to compare and determine the preferable control strategy. Finally, the study performs the sensitivity analysis of economic profitability with variable size, EoL and system price. The research reports that BESS can be profitable in certain cases and presents the recommendations.

Long-term impacts of forest harvesting related soil disturbance on log product yields and economic potential in a New Zealand forest

Abstract

Measurement Problems and Problem-Solving in Kraft Pulping

Tämän työn tarkoituksena on koota yhteen selluprosessin mittausongelmat ja mahdolliset mittaustekniikat ongelmien ratkaisemiseksi. Pääpaino on online-mittaustekniikoissa. Työ koostuu kolmesta osasta. Ensimmäinen osa on kirjallisuustyö, jossa esitellään nykyaikaisen selluprosessin perusmittaukset ja säätötarpeet. Mukana on koko kuitulinja puunkäsittelystä valkaisuun ja kemikaalikierto: haihduttamo, soodakattila, kaustistamo ja meesauuni. Toisessa osassa mittausongelmat ja mahdolliset mittaustekniikat on koottu yhteen ”tiekartaksi”. Tiedot on koottu vierailemalla kolmella suomalaisella sellutehtaalla ja haastattelemalla laitetekniikka- ja mittaustekniikka-asiantuntijoita. Prosessikemian paremmalle ymmärtämiselle näyttää haastattelun perusteella olevan tarvetta, minkä vuoksi konsentraatiomittaukset on valittu jatkotutkimuskohteeksi. Viimeisessä osassa esitellään mahdollisia mittaustekniikoita konsentraatiomittausten ratkaisemiseksi. Valitut tekniikat ovat lähi-infrapunatekniikka (NIR), fourier-muunnosinfrapunatekniikka (FTIR), online-kapillaarielektroforeesi (CE) ja laserindusoitu plasmaemissiospektroskopia (LIPS). Kaikkia tekniikoita voi käyttää online-kytkettyinä prosessikehitystyökaluina. Kehityskustannukset on arvioitu säätöön kytketylle online-laitteelle. Kehityskustannukset vaihtelevat nollasta miestyövuodesta FTIR-tekniikalle viiteen miestyövuoteen CE-laitteelle; kehityskustannukset riippuvat tekniikan kehitysasteesta ja valmiusasteesta tietyn ongelman ratkaisuun. Työn viimeisessä osassa arvioidaan myös yhden mittausongelman – pesuhäviömittauksen – ratkaisemisen teknis-taloudellista kannattavuutta. Ligniinipitoisuus kuvaisi nykyisiä mittauksia paremmin todellista pesuhäviötä. Nykyään mitataan joko natrium- tai COD-pesuhäviötä. Ligniinipitoisuutta voidaan mitata UV-absorptiotekniikalla. Myös CE-laitetta voitaisiin käyttää pesuhäviön mittauksessa ainakin prosessikehitysvaiheessa. Taloudellinen tarkastelu pohjautuu moniin yksinkertaistuksiin ja se ei sovellu suoraan investointipäätösten tueksi. Parempi mittaus- ja säätöjärjestelmä voisi vakauttaa pesemön ajoa. Investointi ajoa vakauttavaan järjestelmään on kannattavaa, jos todellinen ajotilanne on tarpeeksi kaukana kustannusminimistä tai jos pesurin ajo heilahtelee eli pesuhäviön keskihajonta on suuri. 50 000 € maksavalle mittaus- ja säätöjärjestelmälle saadaan alle 0,5 vuoden takaisinmaksuaika epävakaassa ajossa, jos COD-pesuhäviön vaihteluväli on 5,2 – 11,6 kg/odt asetusarvon ollessa 8,4 kg/odt. Laimennuskerroin vaihtelee tällöin välillä 1,7 – 3,6 m3/odt asetusarvon ollessa 2,5 m3/odt.

Development of support and drive systems for defiberization drum

Diplomityön tarkoituksena oli kuidutusrumpulaitteiston käytön- ja kannatuksen kehittä-minen. Työ rajattiin laajuutensa vuoksi koskemaan tuotesarjan viittä pienintä kokoa. Työn alkuosassa käsitellään kuidutuksen teoriaa ja siihen soveltuvia laitteistoja. Käytön suunnittelun kannalta olennaista käynnistystehon tarvetta on tarkasteltu lähtökohdaisesti fysiikan avulla. Perustietoja teorialle on haettu aiemmista tutkimuksista sekä kirjallisuu-desta. Tarkastelun tuloksena teoriaa on kehitty ja se on saatu vastaamaan todellisuutta aiempaa paremmin. Kannatuksen ja käytön toteuttamisvaihtoja etsittäessä on käytetty systemaattisen koneen-suunnittelun keinoja. Saatuja ideoita on arvioitu teknillis-taloudellisin perustein ja näistä on valittu parhaat vaihtoehdot jatkokehitykseen. Jatkokehitysvaiheessa ratkaisuvaihto-ehtoja on tarkasteltu komponenttitasolla ja näistä on tehty yksityiskohtaiset kustannus-laskelmat. Työn tuloksena on esitetty kannatuksen ja käytön toteutusvaihtoehto, jonka avulla voidaan saavuttaa merkittäviä kustannussäästöjä. Korkea, 30 prosentin kustannussäästö-tavoite saavutettiin.

Performance benchmarking and incentive regulation – considerations of directing signals for electricity distribution companies

After the restructuring process of the power supply industry, which for instance in Finland took place in the mid-1990s, free competition was introduced for the production and sale of electricity. Nevertheless, natural monopolies are found to be the most efficient form of production in the transmission and distribution of electricity, and therefore such companies remained franchised monopolies. To prevent the misuse of the monopoly position and to guarantee the rights of the customers, regulation of these monopoly companies is required. One of the main objectives of the restructuring process has been to increase the cost efficiency of the industry. Simultaneously, demands for the service quality are increasing. Therefore, many regulatory frameworks are being, or have been, reshaped so that companies are provided with stronger incentives for efficiency and quality improvements. Performance benchmarking has in many cases a central role in the practical implementation of such incentive schemes. Economic regulation with performance benchmarking attached to it provides companies with directing signals that tend to affect their investment and maintenance strategies. Since the asset lifetimes in the electricity distribution are typically many decades, investment decisions have far-reaching technical and economic effects. This doctoral thesis addresses the directing signals of incentive regulation and performance benchmarking in the field of electricity distribution. The theory of efficiency measurement and the most common regulation models are presented. The chief contributions of this work are (1) a new kind of analysis of the regulatory framework, so that the actual directing signals of the regulation and benchmarking for the electricity distribution companies are evaluated, (2) developing the methodology and a software tool for analysing the directing signals of the regulation and benchmarking in the electricity distribution sector, and (3) analysing the real-life regulatory frameworks by the developed methodology and further develop regulation model from the viewpoint of the directing signals. The results of this study have played a key role in the development of the Finnish regulatory model.

Very preterm infants in Finland - Use of health care services and economic consequences during the first five years of life

The aim of this thesis was to study the health, the hospitalisations, and the use of communal health care services in very preterm children during the first five years of life. In addition, the effect of very preterm birth and prematurity-related morbidities on the costs of hospitalisations, other health care services and the cost per quality adjusted life years (QALY) were studied. This population-based study included all very preterm children (gestational age (GA) <32 weeks or birth weight<1501g, N=2 064) and full-term controls (GA 37+0−41+6, N=200 609) born in Finland during 2000-2003. The data sources included national register data, costing data from the participating hospitals and parental questionnaires. This study showed that most very preterm infants born in Finland survived without prematurity-related morbidities diagnosed during the first years of life. They required relatively little hospital care after the initial discharge, which accounted for the vast majority of the total four-year hospitalisation costs. However, a minority of children born very preterm later developing morbidities had a long initial length of stay and more re-admissions and outpatient visits during the five-year follow-up period. In particular, the number and costs of non-emergency outpatient visits were considerable in individuals with prematurity-related morbidities. The need and costs of hospitalisations decreased clearly with each follow-up year, even in individuals with morbidities. The health-care related costs during the fifth year of life in children born very preterm without prematurity-related morbidities were close to the costs in infants born healthy at term. The cost per QALY of 19,245 € was at an acceptable level already by four years of age in the very preterm population as a whole. Prematurity-related later morbidities and decreasing GA increased the costs per QALY. As the initial hospital stay accounted for a great majority of the total four-year costs, and the costs of hospitalisation decreased with each follow-up year, the cost per QALY is likely to decrease with age. In conclusion, the majority of costs arising after the initial hospitalisation were associated with morbidities related to prematurity. Therefore offering high-quality neonatal care to prevent later morbidities in very preterm survivors has a long-term impact on the cost per QALY. In addition, this study indicates that when estimating the costs of prematurity after the first year of life, one should calculate not only the hospitalisation costs, but also other costs for social welfare services, primary care, and therapies, as these exceed the hospitalisation costs in very preterm infants during the fifth year of life.

An Infant with Food Allergy and Eczema in the Family – The Mental and Economic Burden of Caring

Allergic diseases including food allergy and eczema in an infant in combination with the everyday activities of caring for a family will pose challenges to parents. Only fragments of these challenges are revealed to health care professionals. Families have varying mental, social and economic resources to help them care for an allergic infant, and all such resources are important in determining how families succeed in meeting these challenges and the quality of the infant’s care. This study evaluated the whole burden to the family caused by an infant's allergic disease during the first 24 months of life. As the primary caregiver during this period is usually the mother, her perspective was considered important. Ecocultural theory, which considers families as capable of modifying the positive and negative forces facing them, was taken as the frame of reference. Data were collected as part of an ongoing prospective mother-infant study, and the methods included severity scoring of atopic dermatitis, dietary records, health-related quality of life measurements and assessments of the use of health care services and medications for treating the infant’s eczema, food allergy and asthma. Interviews with mothers were analysed by deductive content analysis on the basis of ecocultural theory and the family empowerment model. The theme “Living an ordinary family life” guided the organization of family activities essential for treating the infant's food allergy and eczema. These activities were sources of both strain and support for the mothers, the allergy-related supporting factors being the mother’s own knowledge of the allergy, hopes for an improvement in the infant’s condition, social support and work. An infant’s food allergy at the age of one year caused considerable strain for the mother in cases where the introduction of new foods into the child’s diet was delayed. This delay was still causing the mother additional strain when the child was 24 months of age. The infants waking at night at the ages of 12 and 24 months because of itching related to eczema caused strain for the mothers. The infants’ health-related quality of life was impaired at ages of 6 and 12 months compared with healthy infants. The principal reasons for impairments were itching, scratching and sleep disturbances at 6 and 12 months and treatment difficulties at 6 months. Problems with getting to sleep were reported at all stages irrespective of eczema and were also present in healthy infants. The economic impact of the treatment of allergic diseases on families during the first 24 months was 131 EUR (2006 value) in cases of eczema and 525 EUR in cases of food allergy. From the societal perspective, the costs of food allergy were a median of 3183 EUR (range 628–11 560 EUR) and of eczema a median of 275 EUR (range 94–1306 EUR). These large variations in costs in food allergy and eczema indicate that disease varies greatly . In conclusion, food allergy and eczema cause extra activities and costs to families which arrange these disease-related activities in such a way that they support the leading family theme “Living an ordinary family life”. Health care professionals should consider this thematic character of family life and disease-related activities in order to ensure that new treatments are sustainable, meaningful and tailored to daily activities. In addition, those mothers who are experiencing difficulties with food allergic infants or infants with eczema should be recognized early and provided with individual encouragement and support from health clinics. In the light of the present results, early detection of symptoms and effective parental guidance can contribute to the well-being and health-related quality of life of the child and family.

Logistics of North-West Russia and Rail Baltica: Standpoints of Private Sector

The main aims of the present report are to describe the current state of railway transport in Russia, and to gather standpoints of Russian private transportation logistics sector towards the development of new railway connection called Rail Baltica Growth Corridor, connecting North-West Russia with Germany through the Baltic States and Poland. North-West Russia plays important role not only in Russian logistics, but also wider European markets as in container sea ports handling is approx. 2.5 mill. TEU p.a. and handling volume in all terminals is above 190 million tons p.a. The whole transportation logistics sector is shortly described as an operational environment for railways – this is done through technical and economic angles. Transportation development is always going in line with economics of the country, so the analysis on economical development is also presented. Logistics integration of the country is strongly influenced by its engagement in the international trade. Although, raw material handling at sea ports and container transports (imports) are blossoming, domestic transportation market is barely growing (in long-term perspective). Thus, recent entrance of Russia into World Trade Organization (WTO) is analyzed theme in this research, as the WTO is an important regulator of the foreign trade and enabler of volume growth in foreign trade related transportation logistics. However, WTO membership can influence negatively the development of Russia’s own industry and its volumes (these have been uncompetitive in global markets for decades). Data gathering in empirical part was accomplished by semi-structured case study interviews among North-West Russian logistics sector actors (private). These were conducted during years 2012-2013, and research compiles findings out of ten case company interviews. Although, there was no sea port involved in the study, most of the interviewed companies relied in European Logistics within significant parts in short sea shipping and truck combined transportation chains (in Russian part also using railways). As the results of the study, it could be concluded that Rail Baltica is seen as possible transport corridor in most of the interviewed companies, if there is enough cargo available. However, interviewees are a bit sceptical, because major and large-scale infrastructural improvements are needed. Delivery time, frequency and price level are three main factors influencing the attractiveness of Rail Baltica route. Price level is the most important feature, but if RB can offer other advantages such as higher frequency, shorter lead times or more developed set of value-added services, then some flexibility is possible for the price level. Environmental issues are not the main criteria of today, but are recognized and discussed among customers. Great uncertainty exists among respondents e.g. on forthcoming sulphur oxide ban on Baltic Sea shipping (whether or not it is going to be implemented in Russia). Rather surprisingly, transportation routes to Eastern Europe and Mediterranean area are having higher value and price space than those to Germany/Central Europe. Border crossing operations (traction monopoly at rails and customs), gauge widths as well as unclear decision-making processes (in Russia), are named as hindering factors. Performance standards for European connected logistics among Russian logistics sector representatives are less demanding as compared to neighbourhood countries belonging to EU.

Design and testing of an armature-reaction-compensated permanent magnet synchronous generator for island operation

At present, permanent magnet synchronous generators (PMSGs) are of great interest. Since they do not have electrical excitation losses, the highly efficient, lightweight and compact PMSGs equipped with damper windings work perfectly when connected to a network. However, in island operation, the generator (or parallel generators) alone is responsible for the building up of the network and maintaining its voltage and reactive power level. Thus, in island operation, a PMSG faces very tight constraints, which are difficult to meet, because the flux produced by the permanent magnets (PMs) is constant and the voltage of the generator cannot be controlled. Traditional electrically excited synchronous generators (EESGs) can easily meet these constraints, because the field winding current is controllable. The main drawback of the conventional EESG is the relatively high excitation loss. This doctoral thesis presents a study of an alternative solution termed as a hybrid excitation synchronous generator (HESG). HESGs are a special class of electrical machines, where the total rotor current linkage is produced by the simultaneous action of two different excitation sources: the electrical and permanent magnet (PM) excitation. An overview of the existing HESGs is given. Several HESGs are introduced and compared with the conventional EESG from technical and economic points of view. In the study, the armature-reaction-compensated permanent magnet synchronous generator with alternated current linkages (ARC-PMSG with ACL) showed a better performance than the other options. Therefore, this machine type is studied in more detail. An electromagnetic design and a thermal analysis are presented. To verify the operation principle and the electromagnetic design, a down-sized prototype of 69 kVA apparent power was built. The experimental results are demonstrated and compared with the predicted ones. A prerequisite for an ARC-PMSG with ACL is an even number of pole pairs (p = 2, 4, 6, …) in the machine. Naturally, the HESG technology is not limited to even-pole-pair machines. However, the analysis of machines with p = 3, 5, 7, … becomes more complicated, especially if analytical tools are used, and is outside the scope of this thesis. The contribution of this study is to propose a solution where an ARC-PMSG replaces an EESG in electrical power generation while meeting all the requirements set for generators given for instance by ship classification societies, particularly as regards island operation. The maximum power level when applying the technology studied here is mainly limited by the economy of the machine. The larger the machine is, the smaller is the efficiency benefit. However, it seems that machines up to ten megawatts of power could benefit from the technology. However, in low-power applications, for instance in the 500 kW range, the efficiency increase can be significant.

Modelling of changes in electricity end-use and their impacts on electricity distribution

The electricity distribution sector will face significant changes in the future. Increasing reliability demands will call for major network investments. At the same time, electricity end-use is undergoing profound changes. The changes include future energy technologies and other advances in the field. New technologies such as microgeneration and electric vehicles will have different kinds of impacts on electricity distribution network loads. In addition, smart metering provides more accurate electricity consumption data and opportunities to develop sophisticated load modelling and forecasting approaches. Thus, there are both demands and opportunities to develop a new type of long-term forecasting methodology for electricity distribution. The work concentrates on the technical and economic perspectives of electricity distribution. The doctoral dissertation proposes a methodology to forecast electricity consumption in the distribution networks. The forecasting process consists of a spatial analysis, clustering, end-use modelling, scenarios and simulation methods, and the load forecasts are based on the application of automatic meter reading (AMR) data. The developed long-term forecasting process produces power-based load forecasts. By applying these results, it is possible to forecast the impacts of changes on electrical energy in the network, and further, on the distribution system operator’s revenue. These results are applicable to distribution network and business planning. This doctoral dissertation includes a case study, which tests the forecasting process in practice. For the case study, the most prominent future energy technologies are chosen, and their impacts on the electrical energy and power on the network are analysed. The most relevant topics related to changes in the operating environment, namely energy efficiency, microgeneration, electric vehicles, energy storages and demand response, are discussed in more detail. The study shows that changes in electricity end-use may have radical impacts both on electrical energy and power in the distribution networks and on the distribution revenue. These changes will probably pose challenges for distribution system operators. The study suggests solutions for the distribution system operators on how they can prepare for the changing conditions. It is concluded that a new type of load forecasting methodology is needed, because the previous methods are no longer able to produce adequate forecasts.

EU Strategy for the Baltic Sea Region: its added value in environmental social and economic dimensions

The European Council has invited the European Commission to present the first macro-regional strategy – the EU Strategy for the Baltic Sea Region (EUSBSR) on the 14th of December 2007, primarily to address collective challenges and opportunities of the Region and also to engender cohesion in support of an European integration policy. However, macro-regional strategies conceived to aid European integration and territorial cohesion were viewed by academics with skepticism, obscuring the strategies’ potential impact. This thesis intends to investigate and measure the added value of the EUSBSR in order to analyze its impact on regional development and its feasibility as a guide for future programs intending to strengthen European cohesion and integration. To determine the added value of the EUSBSR the thesis is organized into three sections, so as to address environmental, social, and economic concerns, respectively. The first case examines EU-Russia cooperation in an environmental context to investigate how environmental cooperation with an external neighbor could forge increased cohesion in a macro-regional setting. To figure the added cooperation that academic cooperation among universities would contribute to social dimension, the work has chosen several study results. Lastly, to measure out the added value for the economic strategy objective, the study employs the project for Improved Global Competitiveness in an example of ‘A Baltic Sea Region Program for Innovation, Cluster and SME-Networks’ as an economic plan.