Talousvesilaitoksen saostusvaiheen tehostaminen esihapetuksella – Case Suomen Sokeri Oy:n vedenkäsittely

Diplomityö tehtiin Suomen Sokeri Oy:n vesilaitokselle Vihreän Kemian laboratoriossa. Prosessia tarkasteltiin saostuksen osalta ja tavoitteena oli sen kehittäminen esihapetusmenetelmän tai saostuskemikaalin vaihdon avulla. Tarkastelu tehtiin orgaanisen, kiintoaineksen ja metallien poiston, desinfiointitehon sekä ympäristöystävällisyyden osalta. Potentiaalisia esihapetusmenetelmiä (kaliumpermanganaatti, vetyperoksidi, valokemiallinen, H2O2/UV, valokatalyyttinen, TiO2/UV, H2O2/ultraääni sekä esihapetus peretikkahapolla) tarkasteltiin eri pitoisuuksilla ja tehoilla laboratoriomittakaavassa jar-testin avulla. Saostustehoa testattiin alumiinikloridilla ja ferrisulfaatilla. Raakaveden laadun muutoksia eri vaiheissa seurattiin laboratorioanalyysein. Hapetusmenetelmien desinfiointiteho, vaikutukset syanobakteereihin ja -toksiineihin sekä reaktioissa syntyvät sivutuotteet kartoitettiin teorian perusteella. Työn tuloksien perusteella kaliumpermanganatti, vetyperoksidi erityisesti kehittyneenä hapetustekniikkana sekä valokatalyyttinen menetelmä tehostivat vedenkäsittelyä, mutta koska TiO2/UV- tai ultraäänihapetukselle ei ole vielä olemassa kaupallista sovellusta laitosmittakaavassa niin suositeltavat menetelmät ovat KMnO4- ja H2O2(/UV)-hapetukset jatkotutkimussuositukset huomioiden. Peretikkahappo ei tämän tutkimuksen perusteella vaikuttanut suositeltavalta hapetusmenetelmältä, mutta sen sijaan teorian perusteella potentiaaliselta desinfektioaineelta myös talousvedenpuhdistukseen. Opinnäytetyötä eri hapetusmenetelmien osalta talousvedelle ei ole aiemmin tehty eikä peretikkahappohapetuksesta ole laajalti aiempaa tutkimustietoa. Kokeellisen osuuden tulokset antavat uutta tietoa menetelmien soveltuvuudesta vastaaville laitoksille.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Oxidation rates of carbon and nitrogen in char residues from solid fuels

Computational fluid dynamics (CFD) modeling is an important tool in designing new combustion systems. By using CFD modeling, entire combustion systems can be modeled and the emissions and the performance can be predicted. CFD modeling can also be used to develop new and better combustion systems from an economical and environmental point of view. In CFD modeling of solid fuel combustion, the combustible fuel is generally treated as single fuel particles. One of the limitations with the CFD modeling concerns the sub-models describing the combustion of single fuel particles. Available models in the scientific literature are in many cases not suitable as submodels for CFD modeling since they depend on a large number of input parameters and are computationally heavy. In this thesis CFD-applicable models are developed for the combustion of single fuel particles. The single particle models can be used to improve the combustion performance in various combustion devices or develop completely new technologies. The investigated fields are oxidation of carbon (C) and nitrogen (N) in char residues from solid fuels. Modeled char-C oxidation rates are compared to experimental oxidation rates for a large number of pulverized solid fuel chars under relevant combustion conditions. The experiments have been performed in an isothermal plug flow reactor operating at 1123-1673 K and 3-15 vol.% O2. In the single particle model, the char oxidation is based on apparent kinetics and depends on three fuel specific parameters: apparent pre-exponential factor, apparent activation energy, and apparent reaction order. The single particle model can be incorporated as a sub-model into a CFD code. The results show that the modeled char oxidation rates are in good agreement with experimental char oxidation rates up to around 70% of burnout. Moreover, the results show that the activation energy and the reaction order can be assumed to be constant for a large number of bituminous coal chars under conditions limited by the combined effects of chemical kinetics and pore diffusion. Based on this, a new model based on only one fuel specific parameter is developed (Paper III). The results also show that reaction orders of bituminous coal chars and anthracite chars differ under similar conditions (Paper I and Paper II); reaction orders of bituminous coal chars were found to be one, while reaction orders of anthracite chars were determined to be zero. This difference in reaction orders has not previously been observed in the literature and should be considered in future char oxidation models. One of the most frequently used comprehensive char oxidation models could not explain the difference in the reaction orders. In the thesis (Paper II), a modification to the model is suggested in order to explain the difference in reaction orders between anthracite chars and bituminous coal chars. Two single particle models are also developed for the NO formation and reduction during the oxidation of single biomass char particles. In the models the char-N is assumed to be oxidized to NO and the NO is partly reduced inside the particle. The first model (Paper IV) is based on the concentration gradients of NO inside and outside the particle and the second model is simplified to such an extent that it is based on apparent kinetics and can be incorporated as a sub-model into a CFD code (Paper V). Modeled NO release rates from both models were in good agreement with experimental measurements from a single particle reactor of quartz glass operating at 1173-1323 K and 3-19 vol.% O2. In the future, the models can be used to reduce NO emissions in new combustion systems.

Reflections on pre-Uralic and the "Saami-Finnic protolanguage"

Vastine Pekka Sammallahden artikkeliin Language and roots Congressus internationalis Fenno-Ugristarum (1995): Congressus octavus internationalis Fenno-Ugristarum, Jyväskylä 10.-15.8.1995. - Jyväskylä : Moderatores. ISBN 952-90-6684-8. Pars 1 : Orationes plenariae et conspectus quinquennales, s. 143-153

Predicting body weight from body measurements of pre-pubertal Ayshire heifers

Selostus: Hiehojen elopainon määrittäminen mittauksin alkukasvatusvaiheessa

Influence of pre partum and post partum plane of nutrition on the performance of crossbred suckler cows and their progeny

Selostus: Sisäruokintakauden energiamäärien vaikutus risteytysemolehmien tuotantoon

Pre-harvest soil acidification, liming or N fertilization did not significantly affect the survival and growth of young Norway spruce

Abstract

Time consumption and damage to the remaining stock in mechanised and motor manual pre-commercial thinning

Abstract

Aqueous photocatalytic oxidation of steroid estrogens

Concerns have increased regarding the detection of endocrine-disrupting compounds in the effluents of sewage treatment plants (STPs). These compounds are able to disrupt normal function of the endocrine system of living organisms even at trace concentrations. Natural and synthetic steroid estrogens (SEs) are believed to be responsible for the majority of the endocrine-disrupting effects. Municipal sewage, the main source of SEs in the environment, is a complex mixture of a wide range of pollutants at concentrations much higher than those of SEs. Low concentrations of SEs in the presence of copollutants thus make their removal problematic. The main objectives of the present work were to study the potential of photocatalytic oxidation (PCO) to effectively treat SE-containing aqueous solutions and to identify the optimum conditions for such treatment. The results showed that SEs can be effectively degraded photocatalytically. Due to the adsorption properties of SEs on the TiO2 photocatalyst surface alkaline medium was found to be beneficial for SE oxidation despite the presence of co-pollutants in concentrations characteristic for the sanitary fraction of municipal sewage. The potential of PCO to selectively oxidise SEs was examined in the presence of copollutants of the sanitary fraction of sewage - urea, saccharose and human urine. The impact of ethanol, often used as a solvent in the preparation of SE stock solutions, was also studied and the results indicated the need to use organic solvent-free solutions for the study of SE behaviour. Photocatalytic oxidation of SEs appeared to be indifferent towards the presence of urea in concentrations commonly found in domestic sewage. The effect of other co-pollutants under consideration was far weaker than could be expected from their concentrations, which are from one hundred to a few thousands times higher than those of the SEs. Although higher concentrations can dramatically slow down the PCO of SEs, realistic concentrations of co-pollutants characteristic for the sanitary fraction of domestic sewage allowed selective removal of SEs. This indicates the potential of PCO to be a selective oxidation method for SE removal from the separate sanitary fraction of municipal sewage.

Photocatalytic oxidation of humic substances and lignins in aqueous solutions

Tässä tutkimuksessa tarkastellaan kahden yleisen, veden ympäristökuormitusta aiheuttavan kemikaaliryhmän, ligniinin ja humusaineiden, fotokatalyyttistahapetusta (photocatalytic oxidation, PCO) vesiliuoksessa. Fotokatalyyttina käytettiin titaanidioksidia, jota säteilytettiin ultraviolettivalolla. Työssä selvitettiin useiden eri olosuhdeparametrien vaikutusta fotokatalyysiin. Tutkittavia parametreja olivat mm. kontaminanttien alkukonsentraatio, pH, vetyperoksidilisäys, rauta-ionien lisäys, fotokatalyysimenetelmä, fotokatalyytin pintakonsentraatioja titaanidioksidin määrä lasisissa mikropartikkeleissa. Ultraviolettivalon lähteinä käytettiin sekä keinovaloa että auringonvaloa. Katalyytin kantoaineena käytettiin huokoisia lasisia mikropartikkeleita, joiden pintaan kiinnittynyt titaanidioksidi pystyi hyvin vähentämään kontaminanttien määrää vedessä. Fotokatalyysin tehokkuus kasvoi humusaine- ja ligniinikonsentraatioiden kasvaessa. Korkeimmat hapetustehokkuudet kumallakin kontaminantilla saavutettiin neutraaleissa jalievästi emäksisissä olosuhteissa huolimatta siitä, että paras adsorboituminen tapahtui happamissa olosuhteissa. Tämän perusteella voidaan olettaa, että humusaineiden ja ligniinin hapetus tapahtuu pääosin radikaalimekanismilla. Vetyperoksidin lisääminen humusaineliuokseen lisäsi hapettumisnopeutta, vaikka näennäinen hapetustehokkuus ei muuttunut. Tämän perusteella vetyperoksidi hapetti myös humusaineita referenssinäytteessä. Ligniinin fotokatalyyttinen hapettuminen parani vetyperoksidilisäyksellä happamissa olosuhteissa johtuen lisääntyneestä OH-radikaalien muodostumisesta. Ligniini ei hapettunut vetyperoksidilla, jos fotokatalyyttiä ei¿ollut läsnä. Rauta-ionit eivät lisänneet humushappojen fotokatalyyttistähapettumista, mutta Fe2+-ionien lisäys aina konsentraatioon 0.05 mM johti ligniinin hapettumistehokkuuden voimakkaaseen kasvuun. Rauta-ionikonsentraation kasvattaminen edelleen johti ligniinin hapetustehokkuuden alenemiseen.

Kinetics of selective oxidation of lactose to lactobionic acid over Pd-active carbon catalyst

Laktoosi eli maitosokeri on tärkein ainesosa useimpien nisäkkäiden tuottamassa maidossa. Sitä erotetaan herasta, juustosta ja maidosta. Laktoosia käytetään elintarvike- ja lääketeollisuuden raaka-aineena monissaeri tuotteissa. Lääketeollisuudessa laktoosia käytetään esimerkiksi tablettien täyteaineena. Hapettamalla laktoosia voidaan valmistaa laktobionihappoa, 2-keto-laktobionihappoa ja laktuloosia. Laktobionihappoa käytetään biohajoavien pintojen ja kosmetiikkatuotteiden valmistuksessa, sekä sisäelinten säilöntäliuoksissa, joissa laktobionihappo estää happiradikaalien aiheuttamien kudosvaurioiden syntymistä. Tässä työssä laktoosia hapetettiin laktobionihapoksi sekoittimella varustetussa laboratoriomittakaavaisessa panosreaktorissa käyttäenkatalyyttinä palladiumia aktiivihiilellä. Muutamissa kokeissa katalyytin promoottorina käytettiin vismuttia, joka hidastaa katalyytin deaktivoitumista. Työn tarkoituksena oli saada lisää tietoa laktoosin hapettamisen kinetiikasta. Laktoosin hapettumisessa laktobionihapoksi havaittiin selektiivisyyteen vaikuttavan muunmuassa reaktiolämpötila, paine, pH ja käytetyn katalyytin määrä. Katalyyttiä kierrättämällä eri kokeiden välillä saatiin paremmat konversiot, selektiivisyydet ja saannot. Parhaat koetulokset saatiin hapetettaessa synteettisellä ilmalla 60 oC lämpötilassa ja 1 bar paineessa. Tehdyissä kokeissa pH:n säätö tehtiin manuaalisesti, joten pH ei pysynyt koko ajan haluttuna. Laktoosin konversio oli parhaimmillaan 95 %. Laktobionihapon suhteellinen selektiivisyys oli 100% ja suhteellinen saanto 100 %. Kinetiikan matemaattinen mallinnus tehtiin Modest-ohjelmalla käyttäen kokeista saatuja mittaustuloksia.Ohjelman avulla estimoitiin parametreja ja saatiin matemaattinen malli reaktorille. Tässä työssä tehtiin kineettinen mallinnus myös ravistelureaktorissa tehdyille laktoosin hapetuskokeille, missä pH pysyi koko ajan haluttuna 'in-situ' titrauksen avulla. Työn yhteydessä selvitettiin myös mahdollisuutta käyttää monoliittikatalyyttejä laktoosin hapetusreaktiossa.