Numerical simulation of two-chamber plasma sources using finite element method

Numerical simulation of plasma sources is very important. Such models allows to vary different plasma parameters with high degree of accuracy. Moreover, they allow to conduct measurements not disturbing system balance.Recently, the scientific and practical interest increased in so-called two-chamber plasma sources. In one of them (small or discharge chamber) an external power source is embedded. In that chamber plasma forms. In another (large or diffusion chamber) plasma exists due to the transport of particles and energy through the boundary between chambers.In this particular work two-chamber plasma sources with argon and oxygen as active mediums were onstructed. This models give interesting results in electric field profiles and, as a consequence, in density profiles of charged particles.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Materiaalimallin määrityksestä kylmämuovattujen putkipalkkien K-liitosten FE-analyysissä

Työssä on tutkittu kylmämuovattujen nelikulmaisten putkipalkkien K-liitosten mallinnusta epälineaarisella elementtimenetelmällä. Työn tärkeimpänä tavoitteena on ollut kehittää putkipalkin osien materiaalimalleja siten, että liitosten kestävyyttä voidaan tutkia laboratoriokokeiden ohella luotettavasti myös elementtimenetelmällä. Toisena tavoitteena on ollut tutkia, voidaanko putkipalkkien liitosten mitoitusohjeita turvallisesti soveltaa kylmämuovatuille putkipalkeille, joissa valmistusprosessi aiheuttaa muutoksia materiaaliominaisuuksiin, erityisesti muodonmuutoskykyyn. Työssä tehtyjen laboratoriokokeiden ja elementtianalyysien perusteella elementti-menetelmä on käyttökelpoinen työkalu putkipalkkiliitosten staattista kestävyyttä määritettäessä, kun materiaalimallit on määritetty oikein. Erityisesti liitoksen käyttö-rajatilan mukaisen kestävyyden laskennassa elementtimenetelmällä saadaan hyvin laboratoriokokeita vastaavia tuloksia. Tehdyt laboratoriokokeet osoittavat myös, että Eurocode 3:n mukaisia putkipalkkien liitosten mitoitusohjeita voi turvallisesti käyttää kylmämuovatuille putkipalkeille.

Miehistönkuljetusajoneuvon rungon suunnittelu

Tämän diplomityön tavoitteena oli suunnitella miehistönkuljetusajoneuvon runko. Rungosta suunniteltiin mahdollisimman hyvin energiaa absorboiva. Rakenne toteutettiin kennora-kenteena. Suunnittelussa sovellettiin koneensuunnittelun periaatteiden lisäksi energiaa ab-sorboivien rakenteiden suunnittelun periaatteita. Myös valmistustekniset näkökohdat otet-tiin huomioon. Rakenteessa hyödynnettiin Ruukki Oy:n Ramor 500 suojausterästä sekä OPTIM 500 MC terästä. Lisäksi erilaisten täyteaineiden käyttöä tutkittiin. Suunnittelun työkaluna käytettiin epälineaarista elementtimenetelmää, koska energiaa ab-sorboivien rakenteiden suunnittelussa on otettava huomioon materiaalien epälineaarinen käyttäytyminen. Rakenteen suunnittelu jakaantui viiteen vaiheeseen. Aluksi rakenteeseen kohdistuvat kuormitukset laskettiin elementtimenetelmän avulla. Esisuunnittelussa lasket-tiin plastisuusteorian avulla alustavasti tarvittavat materiaalipaksuudet. Tämän jälkeen ra-kenteen ydingeometria optimoitiin mahdollisimman hyvin energiaa absorboivaksi. Opti-moinnissa hyödynnettiin elementtimenetelmää. Seuraavassa vaiheessa varmistettiin raken-teen globaalit ominaisuudet. Lopuksi rakenteen kestävyyttä tarkasteltiin elementtimene-telmällä. Runko ei mallien mukaan kestänyt siltä vaadittuja kuormitustapauksia. Mallin kaikki ole-tukset pidettiin varmalla puolella. Reunaehdot oletettiin todellisuutta jäykemmiksi. Myös-kään materiaalin venymänopeudesta johtuvaa lujittumista ei otettu huomioon. Koska mii-naräjähdys on monimutkainen tapahtuma, rungon todellinen kestävyys joudutaan ar-viomaan räjähdystesteillä. Elementtimallien perusteella voidaan kuitenkin sanoa, että ener-giaa absorboiva ajoneuvon runko on mahdollista toteuttaa kennorakenteena. Lisäksi voi-daan todeta, että elementtimenetelmää sopii työvälineeksi tämän tyyppisten rakenteiden suunnitteluun.

Esikiristetyn pulttiliitoksen vaikutus hitsausmuodonmuutoksiin

Tässä työssä tutkitaan propulsioyksikön kiinnitysrenkaan pulttiliitosten vaikutusta asen-nushitsauksesta aiheutuviin hitsausmuodonmuutoksiin. Hitsausmuodonmuutoksissa tutki-taan tärkeimpinä kohtina asennuslohkossa laakerin rajapintaa sekä kääntömoottorin kiinni-tyspintaa. Tutkimuksessa asennuslohkon hitsaaminen ja muodonmuutosten arvioiminen toteutettiin käyttämällä epälineaarista elementtimenetelmää. Ensisijaisena tavoitteena työssä on tutkia esikiristettyjen pulttiliitoksien vaikutusta raken-teen muodonmuutoksiin ja pohtia aiheutuvien siirtymien perusteella pulttien tarpeellisuutta rakenteessa. Tämän lisäksi vertaillaan pultillisen ja pultittoman kiinnitystavan eroavaisuuk-sia tuloksia analysoimalla. Saatujen tuloksien perusteella radiaaliset ja aksiaaliset siirtymät eivät olleet riittävän suuria aiheuttamaan haittoja rakenteen toimivuudelle kummassakaan mallissa. Lisäanalyysejä tar-kemmalla lämmöntuonnilla voidaan pitää tarvittavana pulttiliitoksien tarpeellisuuden tar-kemman testaamisen vuoksi.

Effective notch method assessment of misalignment for fatigue loaded welds

 The objective of this thesis work was to assess axial misalignment in fatigue loaded welds using the effective notch method. As a result, the fatigue behaviour of non-load carrying cruciform fillet welded joint under cyclic tensile loading has been studied. Various degrees of axial misalignment have been found in one series of non-load carrying cruciform fillet welded joints used in a laboratory investigation. As a result, it was important to carry out a comprehensive investigation since axial misalignment forms part of thequality of fatigue loaded structure and can reduce the fatigue strength. To extend the study, the correlation between fatigue strength and stress ratio, as well as stress concentration factor, were also studied. Moreover, a closer investigation of place of crack initiation and its dependence on weld sequence and imperfections of test specimen (angular distortion) was studied. For the fatigue class calculations, FEM (finite element method) and the effectivenotch approach are used. The addressed variable is the axial misalignment whichis introduce by modeling the entire joint. Fracture mechanics based calculations are also used and quantitatively compared with effective notch and experimental results.

Calculation of the critical crack size for cold form rectangular hollow section tube (CRHS) under bending load at -40º C temperature

To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.

Development of beam and plate finite elements based on the absolute nodal coordinate formulation

The focus of this dissertation is to develop finite elements based on the absolute nodal coordinate formulation. The absolute nodal coordinate formulation is a nonlinear finite element formulation, which is introduced for special requirements in the field of flexible multibody dynamics. In this formulation, a special definition for the rotation of elements is employed to ensure the formulation will not suffer from singularities due to large rotations. The absolute nodal coordinate formulation can be used for analyzing the dynamics of beam, plate and shell type structures. The improvements of the formulation are mainly concentrated towards the description of transverse shear deformation. Additionally, the formulation is verified by using conventional iso-parametric solid finite element and geometrically exact beam theory. Previous claims about especially high eigenfrequencies are studied by introducing beam elements based on the absolute nodal coordinate formulation in the framework of the large rotation vector approach. Additionally, the same high eigenfrequency problem is studied by using constraints for transverse deformation. It was determined that the improvements for shear deformation in the transverse direction lead to clear improvements in computational efficiency. This was especially true when comparative stress must be defined, for example when using elasto-plastic material. Furthermore, the developed plate element can be used to avoid certain numerical problems, such as shear and curvature lockings. In addition, it was shown that when compared to conventional solid elements, or elements based on nonlinear beam theory, elements based on the absolute nodal coordinate formulation do not lead to an especially stiff system for the equations of motion.

Ultralujasta teräksestä valmistetun liitoksen pienahitsin staattinen kestävyys

Ultralujat teräkset ovat teräksiä, joiden lujuus on reilusti suurempi verrattuna perinteisiin rakenneteräksiin. Niiden ominaisuuksia hyödynnetään eniten nosto- ja kuljetusvälinete¬ollisuudessa. Ultralujien terästen käyttö avaa suunnittelijalle uusia mahdollisuuksia suun¬nitella ulottuvampia ja kevyempiä rakenteita, jolloin voidaan saavuttaa säästöjä niin val¬mistus- kuin polttoainekustannuksissakin. Ultralujille teräksille ei kuitenkaan ole ole¬massa niitä vastaavia suunnitteluohjeita tai standardeja. Teräsrakenteiden liitosten suun¬nitteluun mitoitusohjeita antava standardi SFS-EN 1993-1-8 ei huomioi teräksiä, joiden myötölujuus on yli 460 MPa. SFS-EN 1993-1-12 on 1993-1-8:n laajennus, joka on voi¬massa myötölujuuteen 700 MPa asti. Tässä diplomityössä tutkittiin ultralujista teräksistä valmistettujen pienahitsiliitosten käyttäytymistä vetokokeiden ja elementtimenetelmän avulla. Tulosten avulla voitiin mää¬rittää matalalujuuksisten terästen mitoitusohjeiden soveltuvuutta ultralujille teräksille. Kokeissa käytetty teräs oli Ruukin valmistama Optim 960 QC.

Vibrations in Rotating Machinery Arising from Minor Imperfections in Component Geometries

Vibrations in machines can cause noise, decrease the performance, or even damage the machine. Vibrations appear if there is a source of vibration that excites the system. In the worst case scenario, the excitation frequency coincides with the natural frequency of the machine causing resonance. Rotating machines are a machine type, where the excitation arises from the machine itself. The excitation originates from the mass imbalance in the rotating shaft, which always exists in machines that are manufactured using conventional methods. The excitation has a frequency that is dependent on the rotational speed of the machine. The rotating machines in industrial use are usually designed to rotate at a constant rotational speed, the case where the resonances can be easily avoided. However, the machines that have a varying operational speed are more problematic due to a wider range of frequencies that have to be avoided. Vibrations, which frequencies equal to rotational speed frequency of the machine are widely studied and considered in the typical machine design process. This study concentrates on vibrations, which arise from the excitations having frequencies that are multiples of the rotational speed frequency. These vibrations take place when there are two or more excitation components in a revolution of a rotating shaft. The dissertation introduces four studies where three kinds of machines are experiencing vibrations caused by different excitations. The first studied case is a directly driven permanent magnet generator used in a wind power plant. The electromagnetic properties of the generator cause harmonic excitations in the system. The dynamic responses of the generator are studied using the multibody dynamics formulation. In another study, the finite element method is used to study the vibrations of a magnetic gear due to excitations, which frequencies equal to the rotational speed frequency. The objective is to study the effects of manufacturing and assembling inaccuracies. Particularly, the eccentricity of the rotating part with respect to non-rotating part is studied since the eccentric operation causes a force component in the direction of the shortest air gap. The third machine type is a tube roll of a paper machine, which is studied while the tube roll is supported using two different structures. These cases are studied using different formulations. In the first case, the tube roll is supported by spherical roller bearings, which have some wavinesses on the rolling surfaces. Wavinesses cause excitations to the tube roll, which starts to resonate at the frequency that is a half of the first natural frequency. The frequency is in the range where the machine normally operates. The tube roll is modeled using the finite element method and the bearings are modeled as nonlinear forces between the tube roll and the pedestals. In the second case studied, the tube roll is supported by freely rotating discs, which wavinesses are also measured. The above described phenomenon is captured as well in this case, but the simulation methodology is based on the flexible multibody dynamics formulation. The simulation models that are used in both of the last two cases studied are verified by measuring the actual devices and comparing the simulated and measured results. The results show good agreement.

Rakenteellisen jouston kuvaus reaaliaikasimuloinnissa

Työn tavoitteena oli tuottaa rakenteellisen jouston huomioiva monikappaledynmiikan simulointiohjelma Matlab-ympäristöön. Rakenteellinen jousto huomioitiin kelluvan koordinaatiston menetelmällä ja joustavuutta kuvaavat muodot ratkaistiin elementtimenetelmällä. Tehdyn ohjelman avulla voidaan koostaa joustavista kappaleista koostuvia avaruusmekanismeja ja tutkia niiden dynaamista käyttäytymistä. Simulointitulosta verrattiin kaupallisen ohjelmiston tuottamaan tulokseen. Työssä havaittiin, että kelluvan koordinaatiston menetelmä on käyttökelpoinen reaaliaikaiseen simulointiin. Työssä toteutetun ohjelman tulokset vastasivat kaupallisen simulointiohjelman tuloksia.

Deep-hole drilling process, monitoring system and sensors modifications

 In the drilling processes and especially deep-hole drilling process, the monitoring system and having control on mechanical parameters (e.g. Force, Torque,Vibration and Acoustic emission) are essential. The main focus of this thesis work is to study the characteristics of deep-hole drilling process, and optimize the monitoring system for controlling the process. The vibration is considered as a major defect area of the deep-hole drilling process which often leads to breakage of the drill, therefore by vibration analysis and optimizing the workpiecefixture, this area is studied by finite element method and the suggestions are explained. By study on a present monitoring system, and searching on the new sensor products, the modifications and recommendations are suggested for optimize the present monitoring system for excellent performance in deep-hole drilling process research and measurements.

Terässiilojen mitoitusohjelman kehittäminen

Siiloja käytetään jauhemaisten ja rakeisten aineiden varastointiin ja annosteluun maataloudessa sekä mm. lasi-, laasti- ja tasoiteteollisuudessa. Tällaiset laitokset toimitetaan usein kokonaistoimituksina, joissa tavanomaisten teräsrakenteiden kustannusvaikutus voi olla jopa 30 % koko toimituksen arvosta. Niinpä osaltaan siilojen tehokkaalla mitoituksella ja erilaisiarakenneratkaisuja vertailemalla voidaan alentaa toimitusten kokonaiskustannuksia. Tässä diplomityössä perehdyttiin siilojen rakenteisiin ja niiden lujuustekniseen mitoitukseen etenkin tuentaratkaisujen osalta. Mitoituksen osalta työssä perehdyttiin pääasiassa uusiin Eurooppalaisiin standardeihin SFS-EN 1991-4 ja SFS-EN 1993-4-1. Niiden mukaan määritetään mitoituskuormat sekä tehdään lujuustekninen mitoitus. Työn tuloksena laadittiin Microsoft Excel -pohjainen mitoitusohjelma, jolla voidaan nopeasti mitoittaa siilojen olennaisimmat teräsrakenteet. Ohjelmalla voidaan määrittää mitoitus koskien siilon lieriön ja kartion seinämiä sekä tuentaratkaisuja. Ohjelma nopeuttaa erityisesti tarjousvaiheen suunnittelua ja antaa pohjan varsinaiselle siilojen yksityiskohtaiselle mitoittamiselle ja suunnittelulle.

Dynamic Simulations of Rotors during Drop on Retainer Bearings

The active magnetic bearings have recently been intensively developed because of noncontact support having several advantages compared to conventional bearings. Due to improved materials, strategies of control, and electrical components, the performance and reliability of the active magnetic bearings are improving. However, additional bearings, retainer bearings, still have a vital role in the applications of the active magnetic bearings. The most crucial moment when the retainer bearings are needed is when the rotor drops from the active magnetic bearings on the retainer bearings due to component or power failure. Without appropriate knowledge of the retainer bearings, there is a chance that an active magnetic bearing supported rotor system will be fatal in a drop-down situation. This study introduces a detailed simulation model of a rotor system in order to describe a rotor drop-down situation on the retainer bearings. The introduced simulation model couples a finite element model with component mode synthesis and detailed bearing models. In this study, electrical components and electromechanical forces are not in the focus. The research looks at the theoretical background of the finite element method with component mode synthesis that can be used in the dynamic analysis of flexible rotors. The retainer bearings are described by using two ball bearing models, which include damping and stiffness properties, oil film, inertia of rolling elements and friction between races and rolling elements. Thefirst bearing model assumes that the cage of the bearing is ideal and that the cage holds the balls in their predefined positions precisely. The second bearing model is an extension of the first model and describes the behavior of the cageless bearing. In the bearing model, each ball is described by using two degrees of freedom. The models introduced in this study are verified with a corresponding actual structure. By using verified bearing models, the effects of the parameters of the rotor system onits dynamics during emergency stops are examined. As shown in this study, the misalignment of the retainer bearings has a significant influence on the behavior of the rotor system in a drop-down situation. In this study, a stability map of the rotor system as a function of rotational speed of the rotor and the misalignment of the retainer bearings is presented. In addition, the effects of parameters of the simulation procedure and the rotor system on the dynamics of system are studied.