Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.

MCMC Analysis for Optimization of Stochastic Models

In any decision making under uncertainties, the goal is mostly to minimize the expected cost. The minimization of cost under uncertainties is usually done by optimization. For simple models, the optimization can easily be done using deterministic methods.However, many models practically contain some complex and varying parameters that can not easily be taken into account using usual deterministic methods of optimization. Thus, it is very important to look for other methods that can be used to get insight into such models. MCMC method is one of the practical methods that can be used for optimization of stochastic models under uncertainty. This method is based on simulation that provides a general methodology which can be applied in nonlinear and non-Gaussian state models. MCMC method is very important for practical applications because it is a uni ed estimation procedure which simultaneously estimates both parameters and state variables. MCMC computes the distribution of the state variables and parameters of the given data measurements. MCMC method is faster in terms of computing time when compared to other optimization methods. This thesis discusses the use of Markov chain Monte Carlo (MCMC) methods for optimization of Stochastic models under uncertainties .The thesis begins with a short discussion about Bayesian Inference, MCMC and Stochastic optimization methods. Then an example is given of how MCMC can be applied for maximizing production at a minimum cost in a chemical reaction process. It is observed that this method performs better in optimizing the given cost function with a very high certainty.

Regulation of Electricity Transmission and Distribution in Russia

The regulation of electricity transmission and distribution business is an essential issue for any electricity market; it is widely introduced in developed electricity markets of Great Britain, Scandinavian countries and United States of America and other. Those markets which were liberalized recently also need well planned regulation model to be chosen and implemented. In open electricity markets the sectors of electricity distribution and transmission remain monopolies, so called "natural monopolies", as introducing the competition into these sectors in most cases appears to be inefficient. Thatis why regulation becomes very important as its main tasks are: to set reasonable tariffs for customers, to ensure non-discriminating process of electricity transmission and distribution, at the same time to provide distribution companies with incentives to operate efficiently and the owners of the companies with reasonable profits as well; the problem of power quality should be solved at the same time. It should be mentioned also, that there is no incentive scheme which will be suitable for any conditions, that is why it is essential to study differentregulation models in order to form the best one for concrete situation. The aim of this Master's Thesis is to give an overview over theregulation of electricity transmission and distribution in Russia. First, the general information about theory of regulation of natural monopolies will be described; the situation in Russian network business and the importance of regulation process for it will be discussed next. Then there is a detailed description ofexisting regulatory system and the process of tariff calculation with an example. And finally, in the work there is a brief analysis of problems of present scheme of regulation, an attempt to predict the following development of regulationin Russia and the perspectives and risks connected to regulation which could face the companies that try to enter Russian electricity market (such as FORTUM OY).

SME internationalisation from a network perspective : an empirical study on a Finnish-Greek business network

The study examines the internationalisation process of a contemporary SME firm and explores the impact of its business network on this development. The objective of the study is to understand SME internationalisation and its dynamics from a network perspective. The purpose of this research project is to describe and explore the development process of a firm and its business network by identifying the changes, critical events and influence factors that form this development. It is a qualitative case study, which focuses on a Finnish focal firm and its respective business network as it expands into the Greek market. It is a longitudinal research process, which covers a period of time from 1994 to 2004. The empirical study concentrates on the paper trading and converting business. The study builds on the network theory and the framework provided by Johanson and Mattsson's (1988) model on network internationalisation. The incremental internationalisation theories and network theories form the theoretical focus. The research project is organised according to a process view. The focal firm evolves from a domestically-oriented small subsidiary into an internationally experienced company, which has activities in several market areas and numerous business networks in various market segments and product categories. The findings illustrate the importance of both the domestic and foreign business network context in a firm's internationalisation process. The results of the study suggest theoretical modifications on a firm's internationalisation process by broadening the perspective and incorporating the strategic context of a firm. The findings suggest that internationalisation process is a non-linear process, which does not have a deterministic order in its development. The findings emphasise the significance of relational networks, both managerial and entrepreneurial, for establishing position in foreign markets. It implies that a firm's evolution is significantly influenced by its business network and by critical events. Business networks gain coherence due to common goals and they use accumulated capabilities to exploit market opportunities. The business network sets constraints and provides opportunities, which makes the related decision making strategically important. The firm co-evolves with its business network. The research project provides an instrumental case study with a description of an SME internationalisation process. It contributes to existing knowledge by illustrating dynamics in an international business network and by pinpointing the importance of suppliers, customers, partners, ownerships and competition to the internationalisation process.

Adaptive Markov chain Monte Carlo and Bayesian filtering for state space models

This thesis is concerned with the state and parameter estimation in state space models. The estimation of states and parameters is an important task when mathematical modeling is applied to many different application areas such as the global positioning systems, target tracking, navigation, brain imaging, spread of infectious diseases, biological processes, telecommunications, audio signal processing, stochastic optimal control, machine learning, and physical systems. In Bayesian settings, the estimation of states or parameters amounts to computation of the posterior probability density function. Except for a very restricted number of models, it is impossible to compute this density function in a closed form. Hence, we need approximation methods. A state estimation problem involves estimating the states (latent variables) that are not directly observed in the output of the system. In this thesis, we use the Kalman filter, extended Kalman filter, Gauss–Hermite filters, and particle filters to estimate the states based on available measurements. Among these filters, particle filters are numerical methods for approximating the filtering distributions of non-linear non-Gaussian state space models via Monte Carlo. The performance of a particle filter heavily depends on the chosen importance distribution. For instance, inappropriate choice of the importance distribution can lead to the failure of convergence of the particle filter algorithm. In this thesis, we analyze the theoretical Lᵖ particle filter convergence with general importance distributions, where p ≥2 is an integer. A parameter estimation problem is considered with inferring the model parameters from measurements. For high-dimensional complex models, estimation of parameters can be done by Markov chain Monte Carlo (MCMC) methods. In its operation, the MCMC method requires the unnormalized posterior distribution of the parameters and a proposal distribution. In this thesis, we show how the posterior density function of the parameters of a state space model can be computed by filtering based methods, where the states are integrated out. This type of computation is then applied to estimate parameters of stochastic differential equations. Furthermore, we compute the partial derivatives of the log-posterior density function and use the hybrid Monte Carlo and scaled conjugate gradient methods to infer the parameters of stochastic differential equations. The computational efficiency of MCMC methods is highly depend on the chosen proposal distribution. A commonly used proposal distribution is Gaussian. In this kind of proposal, the covariance matrix must be well tuned. To tune it, adaptive MCMC methods can be used. In this thesis, we propose a new way of updating the covariance matrix using the variational Bayesian adaptive Kalman filter algorithm.

Benchmarking Spare Parts' Logistics Process

Työn tavoitteena oli selvittää SBU:n varastovaraosien logistinen prosessin tämänhetkinen tilanne verrattuna muihin ja sitä kautta oppia uusia tehokkaita tapoja hallita sitä sekä parantaa sen kilpailukykyä. Selvittäminen tapahtui benchmarkkaamalla SBU:n varastovaraosien logistinen prosessi kahteen sen kilpailijaan ja viiteen muuhun ei kilpailija yritykseen. Bechmarking -aineiston kerääminen tapahtui pääasiassa Inter netin, haastattelujen, bechmarking -kyselyn ja yritysvierailujen avulla. Tulosten vertailu ja analysointi perustui kerättyyn aineistoon. Kriteereiksi lopullista vertailua varten valittiin seikat, joihin liittyvä tieto oli saatavilta suurimmalta osalta bechmarking -yrityksistä. Tuloksena lopullisesta vertailusta muodostettiin "ranking" lista, jossa yritykset on laitettu paremmuus-järjestykseen. Tässä vertailussa SBU sijoittui viimeiseksi ja SBU varastovaraosien logistisessa prosessissa havaittiin olevan useita parannuskohteita. Joka tapauksessa SBU sai paljon tietoa siitä, kuinka muut yritykset hallitsevat prosessinsa ja kuinka SBU:n tulisi tulevaisuudessa hallita oma logistinen prosessinsa ja kuinka se voisi sitä kautta lisätä kilpailukykyään.

In-line Monitoring of Precipitation Process using Raman Spectroscopy and ATR-FTIR

Polymorfian jatkuva seuranta saostuksessa on hyödyllistä suunnittelun ja kidetuotteen ominaisuuksien sekä kiteytystä seuraavan jatkoprosessoinnin kannalta. Tässä diplomityössä on tutkittu L-glutamiinihapon kahden (- ja ß) polymorfimuodon liukoisuuden riippuvuutta pH:sta ja lämpötilasta.Tulokseksi saatiin, että kummankin polymorfin liukoisuus kasvoi sekä pH:ta ettälämpötilaa kasvatettaessa. ¿¿muodon liukoisuus oli korkeampi kuin ß-muodon liukoisuus valituilla pH-arvoilla eri lämpötiloissa. Lisäksi seurattiin puolipanostoimisen saostuksen aikana 1-litraisella laboratoriokiteyttimellä muodostuvan kiteisen polymorfiseoksen koostumusta hyödyntäen in-line Raman-spektroskopiaa. Myös liuoksen pH-muutosta seurattiin sekä liuoksen koostumusta ATR FTIR-spektroskopian (Attenuated Total Reflection Fourier Transform Infrared Spectrometer) avulla. Tutkittavina muuttujina olivat mm. sekoitusintensiteetti, sekoitintyyppi, reaktanttien (natriumglutamaatti ja rikkihappo) konsentraatiot sekä syötetyn rikkihapon syöttökohta kiteyttimessä. Työhön sisältyi 36 koetta ja osa kokeista toistettiin tulosten oikeellisuuden tarkistamiseksi. Inline-mittaustulosten verifioimiseksi kidenäytteet analysoitiin myös käyttämällä konfokaali Raman-mikroskooppia. Kidemorfologiaa tutkittiin SEM-kuvien (Scanning Eletronic Microscope) avulla. Työ osoitti, että Raman-spektroskopia on joustava ja luotettava menetelmä saostusprosessin jatkuvaan seurantaan L-glutamiinihapolla. Alhaiset lähtöainepitoisuudet tuottivat pääasiassa ¿¿muotoa, kun taas alhainen sekoitusteho edisti ß-muodon muodostumista. Syöttökohta vaikutti merkittävästi polymorfiaan. Kun rikkihapon syöttökohta oli epäideaalisesti sekoitetulla vyöhykkeellä, nousi ylikylläisyystaso korkeaksi ja päätuote oli tällöin ß-muotoa. 6-lapainen vinolapaturbiini (nousukulma 45o) ja 6-lapainen levyturbiini eivät merkittävästi poikenneet toisistaan muodostuvien polymorfien osalta.

Modeling of non-isothermalvapor membrane separation with thermodynamic models and generalized mass transfer equations

A rigorous unit operation model is developed for vapor membrane separation. The new model is able to describe temperature, pressure, and concentration dependent permeation as wellreal fluid effects in vapor and gas separation with hydrocarbon selective rubbery polymeric membranes. The permeation through the membrane is described by a separate treatment of sorption and diffusion within the membrane. The chemical engineering thermodynamics is used to describe the equilibrium sorption of vapors and gases in rubbery membranes with equation of state models for polymeric systems. Also a new modification of the UNIFAC model is proposed for this purpose. Various thermodynamic models are extensively compared in order to verify the models' ability to predict and correlate experimental vapor-liquid equilibrium data. The penetrant transport through the selective layer of the membrane is described with the generalized Maxwell-Stefan equations, which are able to account for thebulk flux contribution as well as the diffusive coupling effect. A method is described to compute and correlate binary penetrant¿membrane diffusion coefficients from the experimental permeability coefficients at different temperatures and pressures. A fluid flow model for spiral-wound modules is derived from the conservation equation of mass, momentum, and energy. The conservation equations are presented in a discretized form by using the control volume approach. A combination of the permeation model and the fluid flow model yields the desired rigorous model for vapor membrane separation. The model is implemented into an inhouse process simulator and so vapor membrane separation may be evaluated as an integralpart of a process flowsheet.

The Early Phases of Innovation Process - Case: New Wireless E-Business Opportunities in Forest Industry

Tutkimuksen tavoitteena oli soveltaa innovaatioprosessiteorioita käytäntöön konteksti huomioonottaen, koska langattoman sähköisen liiketoiminnan nopeat muutokset, metsäteollisuuden erityispiirteet ja ei-kaupallisuus asettavat erityistarpeita innovoinnille. Painopiste on prosessin aikaisissa vaiheissa, koska ne ovat kriittisiä koko innovaatioprosessin menestymisen kannalta. Tähtäimenä oli löytää yrityssektorille uusia langattomia sähköisen liiketoiminnan mahdollisuuksia, jotka hyödyttävät tutkimuksessa mukanaolevaa yritystä. Tutkimuksessa käytettiin konstruktiivista tutkimusotetta ja metodeina sähköistä aivomyrskyä, tarkistuslistaa sekä GDSS- ja postikyselyä.Tutkimuksen tuloksena on esitetty innovaatioprosessin aikaiset vaiheet kirjallisuudesta, metsäteollisuuden erityispiirteet ja innovaatioprosessisovellus. Lisäksi tämä tutkimus tuotti uusia sähköisen liiketoiminnan ideoita, suoritti niille seulonnan ja kävi läpi alustavan tutkimuksen.

Non-Linear Journal Bearing Model for Analysis of Superharmonic Vibrations of Rotor Systems

A rotating machine usually consists of a rotor and bearings that supports it. The nonidealities in these components may excite vibration of the rotating system. The uncontrolled vibrations may lead to excessive wearing of the components of the rotating machine or reduce the process quality. Vibrations may be harmful even when amplitudes are seemingly low, as is usually the case in superharmonic vibration that takes place below the first critical speed of the rotating machine. Superharmonic vibration is excited when the rotational velocity of the machine is a fraction of the natural frequency of the system. In such a situation, a part of the machine’s rotational energy is transformed into vibration energy. The amount of vibration energy should be minimised in the design of rotating machines. The superharmonic vibration phenomena can be studied by analysing the coupled rotor-bearing system employing a multibody simulation approach. This research is focused on the modelling of hydrodynamic journal bearings and rotorbearing systems supported by journal bearings. In particular, the non-idealities affecting the rotor-bearing system and their effect on the superharmonic vibration of the rotating system are analysed. A comparison of computationally efficient journal bearing models is carried out in order to validate one model for further development. The selected bearing model is improved in order to take the waviness of the shaft journal into account. The improved model is implemented and analyzed in a multibody simulation code. A rotor-bearing system that consists of a flexible tube roll, two journal bearings and a supporting structure is analysed employing the multibody simulation technique. The modelled non-idealities are the shell thickness variation in the tube roll and the waviness of the shaft journal in the bearing assembly. Both modelled non-idealities may cause subharmonic resonance in the system. In multibody simulation, the coupled effect of the non-idealities can be captured in the analysis. Additionally one non-ideality is presented that does not excite the vibrations itself but affects the response of the rotorbearing system, namely the waviness of the bearing bushing which is the non-rotating part of the bearing system. The modelled system is verified with measurements performed on a test rig. In the measurements the waviness of bearing bushing was not measured and therefore it’s affect on the response was not verified. In conclusion, the selected modelling approach is an appropriate method when analysing the response of the rotor-bearing system. When comparing the simulated results to the measured ones, the overall agreement between the results is concluded to be good.

Utilization of retention chemicals in non-wood containing furnishes

The usage of the non-wood pulps in furnishes for various paper grades is the real alternative for substitution of wood fibres in the papermaking. This is especially important now, when the prices for wood are increasing and forest resources are depleting in many regions of our planet. However, there are several problems associated with utilization of such pulps. In terms of the papermaking process one of the main problems is the poor dewatering of the non-wood pulps. This problem can be partially solved by means of retention aids. In the literature part were described technological features of the non-wood pulps as the raw materials for paper production. Moreover, overviews of the retention chemicals and methods for retention measurement were done; special attention was paid to the mechanisms of retention and drainage. Finally, factors affecting on the drainage and retention of non-wood pulps were considered holistically. Particular emphasis was put on the possibility of enzyme treatment for drainage improvement. It was stated that retention aids can significantly improve dewatering of non-wood pulps. In the experimental part the goal was to investigate influence of various microparticle retention aids on the drainage, retention and formation of furnish containing wheat straw pulp, obtained by novel pulping process (Formico™Fib). The parallel test were performed with reference furnish containing only wood pulps. It was found that Bentonite-CPAM retention aid can significantly improve drainage and retention; however formation seems be suffer from such additives. It was stated that performance of the Silica-Starch retention aid significantly depends on the starch dosing sequence and wet-end conditions; this system have shown better formation than other tested retention aids. Silica-CPAM retention aid have provided comparable results in retention and drainage with Bentonite-CPAM, while Silica-starch did not improve dewatering and yielded in lowest filler retention among other aids. Ultimately, optimal dosages for the tested retention chemicals have been suggested.

Immateriellt kulturarv som begrepp och process : folkloristiska perspektiv på kulturarv i Finlands svenskbygder med folkmusik som exempel

Cultural heritage has become something of an in-word in recent times. Intangible cultural heritage, however, is a category that has received relatively little attention. This folkloristic study focuses on intangible cultural heritage as concept and as process. Folkloristics as a scholarly branch emphasizes non-material culture. Consequently, there is a big potential in bringing existing knowledge of folklore together with current scholarly theories concerning cultural heritage in order to expand the understanding of intangible cultural heritage. In this thesis cultural heritage is regarded as a symbolic construct, which is spoken of and discussed in specific ways. The study of intangible cultural heritage (Swe. kulturarv) as concept focuses on this area. For a cultural component to be experienced as intangible cultural heritage it is, however, not enough to discuss it in those terms. Instead, cultural heritage status needs to be acted out during lengthy processes. This is demonstrated by the study of intangible cultural heritage as process. As a consequence performativity appears crucial to an understanding of cultural heritage – when a sufficient number of people speak and act as if a cultural component has a special status, it will also be perceived as cultural heritage. In this dissertation intangible cultural heritage is studied through cultural analysis, more specifically through discourse analysis. The usage of the concept intangible cultural heritage within cultural organizations, in scholarly use and in the Swedish-speaking press in Finland is examined. Traditional music in the Swedish-speaking districts of Finland is used as a case study of intangible cultural heritage as process. The examination concerns how traditional music, an intangible cultural component, has been discussed, transformed, standardized and objectified in a cultural heritage process. Cultural heritage is generally used as a token of value so that certain cultural components, both intangible and tangible, which are discussed in terms of cultural heritage are perceived to be valuable and should therefore be safeguarded. Intangible cultural heritage depends on performance, that is practitioners use their bodies to act out their traditional knowledge through song, handicraft, storytelling and so on. Intangible cultural components can be transmitted to other individuals in a performance situation, and they can also be documented. In Finland documentation and subsequent filing in archives have been associated with safeguarding of intangible cultural heritage. If the aim of safeguarding is to uphold traditional practices, which is the case for among others UNESCO’s programs aimed at intangible cultural heritage, other efforts are called for: forms of safeguarding that support performance and transmission.

Modelling of ultrasound assisted mixing in Newtonian and non-Newtonian liquids

The purpose of this work is to obtain a better understanding of behaviour of possible ultrasound appliance on fluid media mixing. The research is done in the regard to Newtonian and non-Newtonian fluids. The process of ultrasound appliance on liquids is modelled in COMSOL Multiphysics software. The influence of ultrasound using is introduced as waveform equation. Turbulence modelling is fulfilled by the k-ε model in Newtonian fluid. The modeling of ultrasound assisted mixing in non-Newtonian fluids is based on the power law. To verify modelling results two practical methods are used: Particle Image Velocimetry and measurements of mixing time. Particle Image Velocimetry allows capturing of velocity flow field continuously and presents detailed depiction of liquid dynamics. The second way of verification is the comparison of mixing time of homogeneity. Experimentally achievement of mixing time is done by conductivity measurements. In modelling part mixing time is achieved by special module of COMSOL Multiphysics – the transport of diluted species. Both practical and modelling parts show similar radial mechanism of fluid flow under ultrasound appliance – from the horn tip fluid moves to the bottom and along the walls goes back. Velocity profiles are similar in modelling and experimental part in the case of Newtonian fluid. In the case of non-Newtonian fluid velocity profiles do not agree. The development track of ultrasound-assisted mixing modelling is presented in the thesis.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.

Measurement of social value creation with non-financial measures

This research examines the concept of social entrepreneurship which is a fairly new business model. In the field of business it has become increasingly popular in recent years. The growing awareness of the environment and concrete examples of impact created by social entrepreneurship have encouraged entrepreneurs to address social problems. Society’s failures are tried to redress as a result of business activities. The purpose of doing business is necessarily no longer generating just profits but business is run in order to make a social change with the profit gained from the operations. Successful social entrepreneurship requires a specific nature, constant creativity and strong desire to make a social change. It requires constant balancing between two major objectives: both financial and non-financial issues need to be considered, but not at the expense of another. While aiming at the social purpose, the business needs to be run in highly competitive markets. Therefore, both factors need equally be integrated into an organization as they are complementary, not exclusionary. Business does not exist without society and society cannot go forward without business. Social entrepreneurship, its value creation, measurement tools and reporting practices are under discussion in this research. An extensive theoretical basis is covered and used to support the findings coming out of the researched case enterprises. The most attention is focused on the concept of Social Return on Investment. The case enterprises are analyzed through the SROI process. Social enterprises are mostly small or medium sized. Naturally this sets some limitations in implementing measurement tools. The question of resources requires the most attention and therefore sets the biggest constraints. However, the size of the company does not determine all – the nature of business and the type of social purpose need to be considered always. The mission may be so concrete and transparent that in all cases any kind of measurement would be useless. Implementing measurement tools may be of great benefit – or a huge financial burden. Thus, the very first thing to carefully consider is the possible need of measuring value creation.