Indoor air quality at a waste incineration plant in Finland

Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.

The Current Situation of Sewage Sludge and Manure Treatment in Livestock Enterprises in the Leningrad Region

The problem concerning livestock waste handling in the Leningrad region has been subjected to a number of research works. However, the requirements for use of manure and sewage sludge as well as for treatment processes are not certain. So, this problem remains relevant and, therefore, further investigation ought to be made. Currently a large amount of sewage sludge and manure is generated in the Leningrad region. These livestock wastes have to be obligatory treated. The most common methods for treatment in the region, such as anaerobic digestion, composting and aging as well as the most potential methods are described in the thesis. The most potential methods for the Leningrad region are anaerobic digestion, composting and combustion. Each method has strengths and weaknesses, which are also considered in the paper. Aging was not considered as potential treatment method because it does not meet the sanitary and epidemiological requirements. Furthermore, the work gives an overview and comparison of Finnish and Russian legislative and normative acts concerning livestock wastes handling. On the whole the requirements of the Russian Federation concerning sewage sludge and manure are not much different from the Finnish ones.

Public-private partnership in marine litter waste management

Marine litter is an international environmental problem that causes considerable costs to coastal communities and the fishing industry. Several international and national treaties and regulations have provisions to marine litter and forbid disposal of waste into the sea. However, none of these regulations state a responsibility for public authorities to recover marine litter from the sea, like they do for marine litter that washes up on public beaches. In a financial evaluation of a value chain for marine litter incineration it was found out that the total costs of waste incineration are approximately 100 ─ 200 % higher than waste fees offered by waste contractors of ports. The high costs of incineration are derived from the high calorific value of marine litter and therefore a high incineration cost for the waste, and long distances between ports that are taking part in a project for marine litter recovery from the sea and an Energy-from-Waste (EfW) facility. This study provides a possible solution to diverting marine litter from landfills to more environmentally sustainable EfW use by using a public-private partnership (PPP) framework. PPP would seem to fit as a suitable cooperative approach for answering problems of current marine litter disposal in theory. In the end it is up to the potential partners of this proposed PPP to decide whether the benefits of cooperation justify the required efforts.

Energiapuun kastelu jätetäytön suotovedellä tuhkasta ja kompostista valmistetussa kasvualustassa

Tässä työssä tutkitaan suotoveden käsittelyä käyttämällä sitä kierrätysmateriaaleista valmistetussa tuhkamullassa loppusijoitusalueen päällä kasvatettavan energiapuukasvuston kasteluun. Kyseisen toimintamallin tarkoituksena on haihduttaa suotovettä energiapuiden avulla sekä sitouttaa ravinteita ja haitta-aineita sekä kasvustoon että kasvualustaan. Tavoitteena on selvittää toimintamallin hyödyntämiskelpoisuus ja tehokkuus suotovesien käsittelymenetelmänä sekä kastelun vaikutukset energiapuun kasvuun. Työssä suoritettiin kesän ja syksyn 2014 aikana energiapuun kastelukoe Mustankorkea Oy:n jätteenkäsittelykeskuksen alueella Jyväskylässä. Kokeessa loppusijoitusalueen päälle istutettuja eri kasvuvaiheissa olevia energiapajukasvustoja sekä hybridihaapakasvustoa kasteltiin jätetäytön suotovedellä. Kokeessa käytettiin kasvualustoina tuhkamultaa, joka oli valmistettu tuhkasta, kompostista ja ylijäämämaa- aineksesta, sekä kompostia. Kasteluveden, valumavesien, kasvualustojen ja pajukasvuston ominaisuuksia seurattiin kokeen aikana analyysien avulla. Lisäksi alueen vesitaseen selvittämiseksi suoritettiin lysimetrikokeet, joissa lysimetreihin istutettuja pajuja kasteltiin suotovedellä sekä hanavedellä. Tulosten perusteella suotovesikastelu lisäsi sekä pajun että haavan kasvua. Kastelu lisäsi pajun ravinnepitoisuuksia. Se myös heikensi hieman pajun poltto-ominaisuuksia. Kasvualustan ominaisuuksiin kastelulla ei havaittu olevan vaikutuksia. Kastelumäärä, jota voidaan käyttää ilman valumia, on kokeen perusteella n. 100–600 mm/kasvukausi käytetyllä kastelujärjestelmällä. Kastelujärjestelmää kehittämällä on kuitenkin luultavasti mahdollista lisätä haihduntaa ja siten kastelumäärää merkittävästi.

Waste Management in Commercial Activity: State-of-the-Art and the Potential Innovation in the Urban Areas of Hanoi, Vietnam

As the rapid development of the society as well as the lifestyle, the generation of commercial waste is getting more complicated to control. The situation of packaging waste and food waste – the main fractions of commercial waste in different countries in Europe and Asia is analyzed in order to evaluate and suggest necessary improvements for the existing waste management system in the city of Hanoi, Vietnam. From all waste generation sources of the city, a total amount of approximately 4000 tons of mixed waste is transported to the composting facility and the disposal site, which emits a huge amount of 1,6Mt of GHG emission to the environment. Recycling activity is taking place spontaneously by the informal pickers, leads to the difficulty in managing the whole system and uncertainty of the overall data. With a relative calculation, resulting in only approximately 0,17Mt CO2 equivalent emission, incinerator is suggested to be the solution of the problem with overloaded landfill and raising energy demand within the inhabitants.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Suomalaisten jäte- ja jätevesialan yritysten yhteistyömahdollisuudet sekä uudet tuotekonseptit koti- ja ulkomaisen liiketoiminnan kehittämisessä

Diplomityö on tehty osana InnoEnvi-hanketta, joka on Etelä-Suomen ympäristöalan verkostoitumiseen ja tietoyhteiskunnan kehittymiseen tähtäävä toimintakokonaisuus. InnoEnvi on osa Etelä-Suomen maakuntien valmistelemaa InnoElli-ohjelmaa. InnoEnvi-hankkeen päätavoitteena on kehittyvän ympäristöklusterin luominen Etelä-Suomeen. Monet suomalaiset ympäristöalalle erikoistuneet yritykset ovat vielä tänä päivänä pieniä, nuoria ja pirstaleisia, minkä vuoksi ne tarvitsevat tukea ja yhteistyötä varsinkin vientimarkkinoille pyrkiessään. Tämän työn oleellisimpana tavoitteena oli kartoittaa Etelä-Suomen jäte- ja jätehuoltoalan yritysten yhteistyön mahdollisuuksia ja etuja, sekä yhteistyön tuomaa vaikutusta koti- ja ulkomaiseen liiketoimintaan. Tutkimusongelmaa lähestyttiin kartoittamalla Suomen tämänhetkistä jäte- ja jätevesihuollon tilaa ja käytössä olevaa teknologiaa sekä ympäristöliiketoimintaan vaikuttavia ohjauskeinoja. Ympäristöalan liiketoimintakenttään syvennyttiin tutkimalla alan verkostoitumista ja uusia verkostoitumisen mahdollisuuksia. Verkostoituneita yrityksiä ja yhteistyön lisätarvetta selvitettiin InnoEnvissä tehtyjen aiempien tutkimustulosten sekä tässä tutkimuksessa tehtyjen yrityshaastattelujen avulla. Uudet EU-maat panostavat tiukentuvien ympäristösäädösten takia ympäristönsuojeluun, mikä tekee niistä houkuttelevan ympäristöteknologian vientikohteen. Tässä työssä valittiin tutkimuksen kohteiksi Latvia ja Puola, joiden ympäristöteknologian tasoa ja kehitystarpeita selvitettiin vientipotentiaalin hahmottamiseksi. Molempien maiden jätevesi- ja varsinkin jätehuollossa on paljon kehitettävää, ja maissa panostetaankin kehitystoimiin monin erilaisin valtiollisin ohjelmin. Kotimaisen ympäristöliiketoiminnan kehittämiseksi työssä käsiteltiin neljää tuote- ja palvelukonseptia, jotka valittiin InnoEnvi-hankkeessa tehdystä ajankohtaisesta ympäristöalan investointihankekartoituksesta. Valitut konseptit ovat: REF-valmistuslaitos, jätevesilietteen käsittelylaitteisto, pilaantuneiden maiden käsittelytoimet sekä kaatopaikan lopettaminen. Tuotekonseptit jaettiin osatuotteisiin ja –palveluihin, joita verkostoituneet yritykset voisivat yhdessä tuottaa. Työkaluiksi yritysten kontakteihin nähtiin InnoEnvi-hankkeessa muodostetut miniklusterit ja niiden sisällä kehittyvä toiminta sekä hankkeessa rakennettu www-pohjainen Matching-palvelu. Tutkimuksessa löydettiin uusia mahdollisuuksia yhteistyötoiminnalle. Verkostoitumisessa nähdään haastattelujen mukaan monia etuja: tiedonsaanti, taloudelliset edut, toiminnan luotettavuus sekä uudet virikkeet markkinointiin ja tuotekehitykseen. Lisäyhteistyökumppaneille on haastattelujen mukaan tarvetta. Verkostoituminen tuo vientitoimintaa aloitteleville pk-sektorin yrityksille mahdollisuuden saavuttaa kansainvälistymiseen tarvittavia resursseja. Niin koti- kuin ulkomaisessakin liiketoiminnassa verkoston tärkeimmäksi tekijäksi osoittautui veturiyritys, joka voi vastata verkostossa muun muassa markkinoinnista ja tuotekehityksestä Vientitoiminnassa kohdemaan lainsäädännön ja yleisien toimintatapojen tunteminen on tärkeää. Paikalliset kohdemaan suunnittelu- ja urakointiyritykset ovat tärkeitä yhteistyökumppaneita vientihankkeessa. Latviassa jätehuoltoteknologian kehittämisen tarve on niin yhdyskunta-, ongelma- kuin teollisuusjätteidenkin osalta merkittävä. Puolassa jätesektorin ajankohtaisia aiheita ovat muun muassa kaatopaikkojen vähentäminen ja pakkausjätteen käsittely. Molempien esimerkkimaiden kohdalla jätevesihuollossa tullaan keskittymään lietteiden käsittelyn vaatimiin teknologian tarpeisiin. Vientiosiossa tehtiin vientiyhteistyöesimerkki, jossa tutkittiin kuvitteellista rakennusjätteen käsittelylaitoksen toimittamisprojektia Puolaan. Esimerkkiin saatiin tietoja InnoEnvissä tehdystä Puolan markkinatutkimuksesta. Tulokseksi saatiin viitteitä mahdollisista suomalaisista laitetoimittajista, viisi potentiaalista puolalaista suunnitteluyritystä sekä viisi puolalaista urakoitsijaa. On tärkeää, että kotimaisella yritysryppäällä on kokemusta sujuvasta yhteistyöstä ennen vientiprojektin toteuttamista. Tuotekonseptiesimerkkeihin kartoitettiin pääosa eteläsuomalaisista tuotteiden ja palvelujen tarjoajista. Tarkasteluun otettiin mukaan myös yrityksiä, joiden tuotteet tai palvelut olivat lähellä käsiteltyä konseptia. Tehtyjen yrityslistojen avulla on tarkoitus antaa virikkeitä uusien yritysryppäiden muodostamisesta sekä uusista tuote- ja palveluideoista, joille on nähtävissä markkinapotentiaalia. InnoEnvi-hankkeessa valmisteltujen työkalujen avulla eteläsuomalaiset yhteistyöstä kiinnostuneet yritykset voivat luoda kontakteja ja kokoontua miettimään tulevien investointihankkeiden toteuttamista kotimaassa ja myöhemmin jopa ulkomailla. Työn tuloksia esitellään InnoEnvi-hankkeen toimijoiden kautta jäteminiklusterissa toimiville eteläsuomalaisille yrityksille.

Energy-efficient control strategies for variable speed driven parallel pumping systems based on pump operation point monitoring with frequency converters

The pumping processes requiring wide range of flow are often equipped with parallelconnected centrifugal pumps. In parallel pumping systems, the use of variable speed control allows that the required output for the process can be delivered with a varying number of operated pump units and selected rotational speed references. However, the optimization of the parallel-connected rotational speed controlled pump units often requires adaptive modelling of both parallel pump characteristics and the surrounding system in varying operation conditions. The available information required for the system modelling in typical parallel pumping applications such as waste water treatment and various cooling and water delivery pumping tasks can be limited, and the lack of real-time operation point monitoring often sets limits for accurate energy efficiency optimization. Hence, alternatives for easily implementable control strategies which can be adopted with minimum system data are necessary. This doctoral thesis concentrates on the methods that allow the energy efficient use of variable speed controlled parallel pumps in system scenarios in which the parallel pump units consist of a centrifugal pump, an electric motor, and a frequency converter. Firstly, the suitable operation conditions for variable speed controlled parallel pumps are studied. Secondly, methods for determining the output of each parallel pump unit using characteristic curve-based operation point estimation with frequency converter are discussed. Thirdly, the implementation of the control strategy based on real-time pump operation point estimation and sub-optimization of each parallel pump unit is studied. The findings of the thesis support the idea that the energy efficiency of the pumping can be increased without the installation of new, more efficient components in the systems by simply adopting suitable control strategies. An easily implementable and adaptive control strategy for variable speed controlled parallel pumping systems can be created by utilizing the pump operation point estimation available in modern frequency converters. Hence, additional real-time flow metering, start-up measurements, and detailed system model are unnecessary, and the pumping task can be fulfilled by determining a speed reference for each parallel-pump unit which suggests the energy efficient operation of the pumping system.

Wooden packaging waste reuse and refining

The aim of the thesis was both to study wooden packaging waste reuse and refining generated in the forestry machine factory environment, and to find alternative wooden packaging waste utilization options in order to create a new operating model which would decrease the overall amount of waste produced. As environmental and waste legislation has become more rigid and companies' own environmental management systems’ requirements and control have increased, companies have had to consider their environmental aspects more carefully. Companies have to take into account alternative ways of reducing waste through an increase in reuse and recycling. A part of this waste is from different forms of packaging. In the metal industry the most heavily used packaging material is wooden packaging, as such material is heavy and the packaging has to be able to bear heavy stress. In the theoretical part of the thesis, the requirements of packaging and packaging waste legislation, as well as environmental management systems governing companies’ processing of their packaging waste, are studied. The theoretical part includes a process study of systems, which direct packaging waste and wooden packaging waste refining. In addition, methods related to the continuous improvement of these processes are introduced. This thesis concentrates on designing and creating a new operating model in relation to wooden packaging waste processing. The main target was to find an efficient model in order to decrease the total amount of wooden packaging waste and to increase refining. The empirical part introduces methods for approaches to wooden packaging waste re-utilization, as well as a description of a new operating model and its impact.