Towards input/output-free modelling of linear infinite-dimensional systems in continuous time

This dissertation describes a networking approach to infinite-dimensional systems theory, where there is a minimal distinction between inputs and outputs. We introduce and study two closely related classes of systems, namely the state/signal systems and the port-Hamiltonian systems, and describe how they relate to each other. Some basic theory for these two classes of systems and the interconnections of such systems is provided. The main emphasis lies on passive and conservative systems, and the theoretical concepts are illustrated using the example of a lossless transfer line. Much remains to be done in this field and we point to some directions for future studies as well.

Solving Leontief Input-Output Model with Trapezoidal Fuzzy Numbers and Gauss-Seidel Algorithm

In this work a fuzzy linear system is used to solve Leontief input-output model with fuzzy entries. For solving this model, we assume that the consumption matrix from di erent sectors of the economy and demand are known. These assumptions heavily depend on the information obtained from the industries. Hence uncertainties are involved in this information. The aim of this work is to model these uncertainties and to address them by fuzzy entries such as fuzzy numbers and LR-type fuzzy numbers (triangular and trapezoidal). Fuzzy linear system has been developed using fuzzy data and it is solved using Gauss-Seidel algorithm. Numerical examples show the e ciency of this algorithm. The famous example from Prof. Leontief, where he solved the production levels for U.S. economy in 1958, is also further analyzed.

Structural dynamics in the global pulp and paper industry

The pulp and paper industry is currently facing broad structural changes due to global shifts in demand and supply. These changes have significant impacts on national economies worldwide. Planted forests (especially eucalyptus) and recovered paper have quickly increased their importance as raw material for paper and paperboard production. Although advances in information and communication technologies could reduce the demand for communication papers, and the growth of paper consumption has indeed flattened in developed economies, particularly in North America and Western Europe, the consumption is increasing on a global scale. Moreover, the focal point of production and consumption is moving from the Western world to the rapidly growing markets of Southeast Asia. This study analyzes how the so-called megatrends (globalization, technological development, and increasing environmental awareness) affect the pulp and paper industry’s external environment, and seeks reliable ways to incorporate the impact of the megatrends on the models concerning the demand, trade, and use of paper and pulp. The study expands current research in several directions and points of view, for example, by applying and incorporating several quantitative methods and different models. As a result, the thesis makes a significant contribution to better understand and measure the impacts of structural changes on the pulp and paper industry. It also provides some managerial and policy implications.

Fluoriditasetarkastelu ja päästöjen hallinta ferrokromi- ja terästeollisuudessa

Työn alkuosassa kartoitettiin AvestaPolarit –yhtiöiden Tornion tehtaiden keskeiset fluoridilähteet kuten fluspaatti, valukuonat, valupulverit ja fluorivetyhappo. Valupulverien ja kuonien haihtumis- ja liukoisuuskäyttäytymistä valaistiin kotimaisten ja kansainvälisten tutkimusten avulla. Tutkimustuloksia sovellettiin pääpiirteittäin Tornion tehtaiden tilanteeseen ottamalla huomioon tekijät, jotka saattoivat lieventää tai vahvistaa fluoridien vaikutusta ympäristöön. Yleisesti fluoridien ympäristö- ja terveysvaikutukset arvioitiin vähäisiksi. Työn kokeellisessa osassa määritettiin Tornion tehtaiden ferrokromitehtaan, terässulaton, kuumavalssaamon ja kylmävalssaamon fluoriditaseet. Jokaisen osastojen syötteiden fluoridipitoisuudet selvitettiin tuottajien ilmoittamien tuotekoostumuksien, spesifikaatioiden ja fluoridianalyysien perusteella. Fluoridien kokonaismäärät laskettiin jokaiselle syötteelle ja ne suhteutettiin kunkin osaston vuoden 2001 tuotantotasoon. Tasetarkastelussa suurimpina fluoridisyötteinä nousivat odotetusti esiin terässulaton käyttämä kuonanmuodostaja-aine fluspaatti (CaF2) ja kylmävalssaamon peittaushappo, 70 prosenttinen fluorivetyhappo (HF). Lisäksi muita merkittäviä syötteitä olivat kylmävalssaamon käyttämä kalkkipitoinen sekakuona ja ferrokromitehtaan sulatuskoksi. Tuotoksien eli päästöjen fluoridipitoisuudet saatiin selville päästömittauksin. Jätevesistä otettiin pääosin viikoittaisia kokoomanäytteitä, jotka analysoitiin tehtaan laboratoriossa. Kaasumaiset tuotokset oli määritetty kertamittauksien perusteella. Kiinteiden tuotoksien eli sakkojen ja kuonien fluoridimittaukset suoritettiin 3 sulatuksen kuonanäytteistä ja sakan vuosinäytteestä. Tuotoksista suurimmat ominaispäästökertoimet olivat juuri terässulaton AOD-konvertterin ja senkkauunin kuonilla ja kylmävalssaamon neutraloidulla regenerointisakalla ja neutralointisakoilla. Näistä ei aiheutunut varsinaista päästöä lähiympäristöön, koska sakat ja kuonat loppusijoitetaan tehtaan kaatopaikalle tai niitä käytetään liukenemattomassa muodossa. Tornion tehtaiden fluoridisyötteiden ja -tuotoksien mittausepätarkkuudet vaikuttivat fluoriditaseeseen. Ferrokromitehtaan fluoridisyötteet olivat kokonaismäärältään selvästi suurempia kuin tuotokset. Terässulaton fluoriditaseen tuotokset olivat suurempia kuin syötteet ja kylmävalssaamon syötteet sekä tuotokset olivat karkeasti arvioiden samaa suuruusluokkaa. Kuumavalssaamon fluoridisyötteet ja -tuotokset olivat mitättömiä. Fluoriditaseen epävarmuustekijöitä voidaan vähentää suorittamalla esimerkiksi useita fluoridimittauksia kaasumaisista päästöistä.

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.

JNK regulates dendrite and spine architecture in the central nervous system influencing spatial learning and motor tasks

JNK1 is a MAP-kinase that has proven a significant player in the central nervous system. It regulates brain development and the maintenance of dendrites and axons. Several novel phosphorylation targets of JNK1 were identified in a screen performed in the Coffey lab. These proteins were mainly involved in the regulation of neuronal cytoskeleton, influencing the dynamics and stability of microtubules and actin. These structural proteins form the dynamic backbone for the elaborate architecture of the dendritic tree of a neuron. The initiation and branching of the dendrites requires a dynamic interplay between the cytoskeletal building blocks. Both microtubules and actin are decorated by associated proteins which regulate their dynamics. The dendrite-specific, high molecular weight microtubule associated protein 2 (MAP2) is an abundant protein in the brain, the binding of which stabilizes microtubules and influences their bundling. Its expression in non-neuronal cells induces the formation of neurite-like processes from the cell body, and its function is highly regulated by phosphorylation. JNK1 was shown to phosphorylate the proline-rich domain of MAP2 in vivo in a previous study performed in the group. Here we verify three threonine residues (T1619, T1622 and T1625) as JNK1 targets, the phosphorylation of which increases the binding of MAP2 to microtubules. This binding stabilizes the microtubules and increases process formation in non-neuronal cells. Phosphorylation-site mutants were engineered in the lab. The non-phosphorylatable mutant of MAP2 (MAP2- T1619A, T1622A, T1625A) in these residues fails to bind microtubules, while the pseudo-phosphorylated form, MAP2- T1619D, T1622D, Thr1625D, efficiently binds and induces process formation even without the presence of active JNK1. Ectopic expression of the MAP2- T1619D, T1622D, Thr1625D in vivo in mouse brain led to a striking increase in the branching of cortical layer 2/3 (L2/3) pyramidal neurons, compared to MAP2-WT. The dendritic complexity defines the receptive field of a neuron and dictates the output to the postsynaptic cells. Previous studies in the group indicated altered dendrite architecture of the pyramidal neurons in the Jnk1-/- mouse motor cortex. Here, we used Lucifer Yellow loading and Sholl analysis of neurons in order to study the dendritic branching in more detail. We report a striking, opposing effect in the absence of Jnk1 in the cortical layers 2/3 and 5 of the primary motor cortex. The basal dendrites of pyramidal neurons close to the pial surface at L2/3 show a reduced complexity. In contrast, the L5 neurons, which receive massive input from the L2/3 neurons, show greatly increased branching. Another novel substrate identified for JNK1 was MARCKSL1, a protein that regulates actin dynamics. It is highly expressed in neurons, but also in various cancer tissues. Three phosphorylation target residues for JNK1 were identified, and it was demonstrated that their phosphorylation reduces actin turnover and retards migration of these cells. Actin is the main cytoskeletal component in dendritic spines, the site of most excitatory synapses in pyramidal neurons. The density and gross morphology of the Lucifer Yellow filled dendrites were characterized and we show reduced density and altered morphology of spines in the motor cortex and in the hippocampal area CA3. The dynamic dendritic spines are widely considered to function as the cellular correlate during learning. We used a Morris water maze to test spatial memory. Here, the wild-type mice outperformed the knock-out mice during the acquisition phase of the experiment indicating impaired special memory. The L5 pyramidal neurons of the motor cortex project to the spinal cord and regulate the movement of distinct muscle groups. Thus the altered dendrite morphology in the motor cortex was expected to have an effect on the input-output balance in the signaling from the cortex to the lower motor circuits. A battery of behavioral tests were conducted for the wild-type and Jnk1-/- mice, and the knock-outs performed poorly compared to wild-type mice in tests assessing balance and fine motor movements. This study expands our knowledge of JNK1 as an important regulator of the dendritic fields of neurons and their manifestations in behavior.

Uncertainty of Efficiency Measurements in Electric Drives

The two central goals of this master's thesis are to serve as a guidebook on the determination of uncertainty in efficiency measurements and to investigate sources of uncertainty in efficiency measurements in the field of electric drives by a literature review, mathematical modeling and experimental means. The influence of individual sources of uncertainty on the total instrumental uncertainty is investigated with the help of mathematical models derived for a balance and a direct air cooled calorimeter. The losses of a frequency converter and an induction motor are measured with the input-output method and a balance calorimeter at 50 and 100 % loads. A software linking features of Matlab and Excel is created to process measurement data, calculate uncertainties and to calculate and visualize results. The uncertainties are combined with both the worst case and the realistic perturbation method and distributions of uncertainty by source are shown based on experimental results. A comparison of the calculated uncertainties suggests that the balance calorimeter determines losses more accurately than the input-output method with a relative RPM uncertainty of 1.46 % compared to 3.78 - 12.74 % respectively with 95 % level of confidence at the 93 % induction motor efficiency or higher. As some principles in uncertainty analysis are open to interpretation the views and decisions of the analyst can have noticeable influence on the uncertainty in the measurement result.

Optimisation of data analysis method for a fluidized bed combustion test rig

Nowadays the used fuel variety in power boilers is widening and new boiler constructions and running models have to be developed. This research and development is done in small pilot plants where more faster analyse about the boiler mass and heat balance is needed to be able to find and do the right decisions already during the test run. The barrier on determining boiler balance during test runs is the long process of chemical analyses of collected input and outputmatter samples. The present work is concentrating on finding a way to determinethe boiler balance without chemical analyses and optimise the test rig to get the best possible accuracy for heat and mass balance of the boiler. The purpose of this work was to create an automatic boiler balance calculation method for 4 MW CFB/BFB pilot boiler of Kvaerner Pulping Oy located in Messukylä in Tampere. The calculation was created in the data management computer of pilot plants automation system. The calculation is made in Microsoft Excel environment, which gives a good base and functions for handling large databases and calculations without any delicate programming. The automation system in pilot plant was reconstructed und updated by Metso Automation Oy during year 2001 and the new system MetsoDNA has good data management properties, which is necessary for big calculations as boiler balance calculation. Two possible methods for calculating boiler balance during test run were found. Either the fuel flow is determined, which is usedto calculate the boiler's mass balance, or the unburned carbon loss is estimated and the mass balance of the boiler is calculated on the basis of boiler's heat balance. Both of the methods have their own weaknesses, so they were constructed parallel in the calculation and the decision of the used method was left to user. User also needs to define the used fuels and some solid mass flowsthat aren't measured automatically by the automation system. With sensitivity analysis was found that the most essential values for accurate boiler balance determination are flue gas oxygen content, the boiler's measured heat output and lower heating value of the fuel. The theoretical part of this work concentrates in the error management of these measurements and analyses and on measurement accuracy and boiler balance calculation in theory. The empirical part of this work concentrates on the creation of the balance calculation for the boiler in issue and on describing the work environment.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

The Use of Data Envelopment Analysis as Equity Portfolio Selection Criterion in the Finnish Stock Market

This thesis examines the application of data envelopment analysis as an equity portfolio selection criterion in the Finnish stock market during period 2001-2011. A sample of publicly traded firms in the Helsinki Stock Exchange is examined in this thesis. The sample covers the majority of the publicly traded firms in the Helsinki Stock Exchange. Data envelopment analysis is used to determine the efficiency of firms using a set of input and output financial parameters. The set of financial parameters consist of asset utilization, liquidity, capital structure, growth, valuation and profitability measures. The firms are divided into artificial industry categories, because of the industry-specific nature of the input and output parameters. Comparable portfolios are formed inside the industry category according to the efficiency scores given by the DEA and the performance of the portfolios is evaluated with several measures. The empirical evidence of this thesis suggests that with certain limitations, data envelopment analysis can successfully be used as portfolio selection criterion in the Finnish stock market when the portfolios are rebalanced at annual frequency according to the efficiency scores given by the data envelopment analysis. However, when the portfolios were rebalanced every two or three years, the results are mixed and inconclusive.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Evaluation of performance analysis software for Linux computing cluster

Tietokonejärjestelmän osien ja ohjelmistojen suorituskykymittauksista saadaan tietoa,jota voidaan käyttää suorituskyvyn parantamiseen ja laitteistohankintojen päätöksen tukena. Tässä työssä tutustutaan suorituskyvyn mittaamiseen ja mittausohjelmiin eli ns. benchmark-ohjelmistoihin. Työssä etsittiin ja arvioitiin eri tyyppisiä vapaasti saatavilla olevia benchmark-ohjelmia, jotka soveltuvat Linux-laskentaklusterin suorituskyvynanalysointiin. Benchmarkit ryhmiteltiin ja arvioitiin testaamalla niiden ominaisuuksia Linux-klusterissa. Työssä käsitellään myös mittausten tekemisen ja rinnakkaislaskennan haasteita. Benchmarkkeja löytyi moneen tarkoitukseen ja ne osoittautuivat laadultaan ja laajuudeltaan vaihteleviksi. Niitä on myös koottu ohjelmistopaketeiksi, jotta laitteiston suorituskyvystä saisi laajemman kuvan kuin mitä yhdellä ohjelmalla on mahdollista saada. Olennaista on ymmärtää nopeus, jolla dataa saadaan siirretyä prosessorille keskusmuistista, levyjärjestelmistä ja toisista laskentasolmuista. Tyypillinen benchmark-ohjelma sisältää paljon laskentaa tarvitsevan matemaattisen algoritmin, jota käytetään tieteellisissä ohjelmistoissa. Benchmarkista riippuen tulosten ymmärtäminen ja hyödyntäminen voi olla haasteellista.

Fuzzy Principal Components Analysis

Due to the large number of characteristics, there is a need to extract the most relevant characteristicsfrom the input data, so that the amount of information lost in this way is minimal, and the classification realized with the projected data set is relevant with respect to the original data. In order to achieve this feature extraction, different statistical techniques, as well as the principal components analysis (PCA) may be used. This thesis describes an extension of principal components analysis (PCA) allowing the extraction ofa finite number of relevant features from high-dimensional fuzzy data and noisy data. PCA finds linear combinations of the original measurement variables that describe the significant variation in the data. The comparisonof the two proposed methods was produced by using postoperative patient data. Experiment results demonstrate the ability of using the proposed two methods in complex data. Fuzzy PCA was used in the classificationproblem. The classification was applied by using the similarity classifier algorithm where total similarity measures weights are optimized with differential evolution algorithm. This thesis presents the comparison of the classification results based on the obtained data from the fuzzy PCA.

Performance analysis of software run-time behaviour using 3D-visualisation

Monimutkaisen tietokonejärjestelmän suorituskykyoptimointi edellyttää järjestelmän ajonaikaisen käyttäytymisen ymmärtämistä. Ohjelmiston koon ja monimutkaisuuden kasvun myötä suorituskykyoptimointi tulee yhä tärkeämmäksi osaksi tuotekehitysprosessia. Tehokkaampien prosessorien käytön myötä myös energiankulutus ja lämmöntuotto ovat nousseet yhä suuremmiksi ongelmiksi, erityisesti pienissä, kannettavissa laitteissa. Lämpö- ja energiaongelmien rajoittamiseksi on kehitetty suorituskyvyn skaalausmenetelmiä, jotka edelleen lisäävät järjestelmän kompleksisuutta ja suorituskykyoptimoinnin tarvetta. Tässä työssä kehitettiin visualisointi- ja analysointityökalu ajonaikaisen käyttäytymisen ymmärtämisen helpottamiseksi. Lisäksi kehitettiin suorituskyvyn mitta, joka mahdollistaa erilaisten skaalausmenetelmien vertailun ja arvioimisen suoritusympäristöstä riippumatta, perustuen joko suoritustallenteen tai teoreettiseen analyysiin. Työkalu esittää ajonaikaisesti kerätyn tallenteen helposti ymmärrettävällä tavalla. Se näyttää mm. prosessit, prosessorikuorman, skaalausmenetelmien toiminnan sekä energiankulutuksen kolmiulotteista grafiikkaa käyttäen. Työkalu tuottaa myös käyttäjän valitsemasta osasta suorituskuvaa numeerista tietoa, joka sisältää useita oleellisia suorituskykyarvoja ja tilastotietoa. Työkalun sovellettavuutta tarkasteltiin todellisesta laitteesta saatua suoritustallennetta sekä suorituskyvyn skaalauksen simulointia analysoimalla. Skaalausmekanismin parametrien vaikutus simuloidun laitteen suorituskykyyn analysoitiin.

Reporting Framework: Implementation and Performance Analysis

Fenix on suuri metsäteollisuuden tuotannonohjausjärjestelmä. Fenix-järjestelmän raportointi- ja tulostuspalvelut elävätvaihdekautta. Aikaisemmin käytetyt raportointityökalut ovat vanhentumassa ja neon korvattava uusilla. Uusi raportointialusta, Global Printing System (GPS), onrakennettu StreamServe Business Communication Platformin ympärille. Uuden alustan on tarkoitus hoitaa Fenixin tulostus sekä raportointitehtävät. Työ kuvaa raportointialustan toteutuksen sekä sen tärkeimmät ominaisuudet. Uuden alustan suorituskyvyssä on ollut toivomisen varaa. Etenkin suurien raporttien generoiminen on kestänyt joskus toivottoman pitkään. Työssä analysoidaan raportointialustan suorituskykyä ja etsitään mahdolliset pullonkaulat. Suorituskyvyn heikkouksiin pyritään löytämään ratkaisut ja annetaan ehdotuksia suorituskyvyn parantamiseksi. XML pohjaisena järjestelmänä GPS:n suorituskyvyssä suurta osaaesittää XML:n tehokkuus. GPS sisääntuleva data tulee XML-muodossa ja sisääntulon parsimisen tehokkuus on avaintekijöitä koko GPS:n tehokkuuden kannalta. Suorituskyvyn parantamisessa keskitytäänki vahvasti XML:n tehokkaampaan käyttöön ja esitetään ehdotuksia sen parantamiseksi.