Reducing contact resistance in graphene devices

In this thesis, the contact resistance of graphene devices was investigated because high contact resistance is detrimental to the performance of graphene field-effect transistors (GFET). Method for increasing so-called edge-contact area was applied in device fabrication process, as few nanometers thick Ni layer was used as a catalytic etchant during the annealing process. Finally, Ni was also used as a metal for contact. GFETs were fabricated using electron beam lithography using graphene fabricated by chemical vapor deposition (CVD). Critical part of the fabrication process was to preserve the high quality of the graphene channel while etching the graphene at contact areas with Ni during the annealing. This was achieved by optimizing the combination of temperature and gas flows. The structural properties of graphene were studied using scanning electron microscopy, scanning confocal μ-Raman spectroscopy and optical microscopy. Evaluation of electric transport properties including contact resistance was carried out by transmission line method and four-probe method. The lowest contact resistance found was about at 350 Ωμm. In addition, different methods to transfer CVD graphene synthesized on copper were studied. Typical method using PMMA as a supporting layer leaves some residues after its removal, thus effecting on the performance of a graphene devices. In a metal assisted transfer method, metal is used as an interfacial layer between PMMA and graphene. This allows more effective removal of PMMA. However, Raman spectra of graphene transferred by metal assisted method showed somewhat lower quality than the PMMA assisted method

On the development of object functions and restrictions for shapes made with a turret punch press

This study presents the information required to describe the machine and device resources in the turret punch press environment which are needed for the development of the analysing method for automated production. The description of product and device resources and their interconnectedness is the starting point for method comparison the development of expenses, production planning and the performance of optimisation. The manufacturing method cannot be optimized unless the variables and their interdependence are known. Sheet metal parts in particular may then become remarkably complex, and their automatic manufacture may be difficult or, with some automatic equipment, even impossible if not know manufacturing properties. This thesis consists of three main elements, which constitute the triangulation. In the first phase of triangulation, the manufacture occuring on a turret punch press is examined in order to find the factors that affect the efficiency of production. In the second phase of triangulation, the manufacturability of products on turret punch presses is examined through a set of laboratory tests. The third phase oftriangulation involves an examination of five industry parts. The main key findings of this study are: all possible efficiency in high automation level machining cannot be achieved unless the raw materials used in production and the dependencies of the machine and tools are well known. Machine-specific manufacturability factors for turret punch presses were not taken into account in the industrial case samples. On the grounds of the performed tests and industrial case samples, the designer of a sheet metal product can directly influence the machining time, material loss, energy consumption and the number of tools required on a turret punch press by making decisions in the way presented in the hypothesis of thisstudy. The sheet metal parts to be produced can be optimised to bemanufactured on a turret punch press when the material to be used and the kinds of machine and tool options available are known. This provides in-depth knowledge of the machine and tool properties machine and tool-specifically. None of the optimisation starting points described here is a separate entity; instead, they are all connected to each other.

Switchable lanthanide fluorescence probes in homogenous molecular diagnostics

The number of molecular diagnostic assays has increased tremendously in recent years.Nucleic acid diagnostic assays have been developed, especially for the detection of human pathogenic microbes and genetic markers predisposing to certain diseases. Closed-tube methods are preferred because they are usually faster and easier to perform than heterogenous methods and in addition, target nucleic acids are commonly amplified leading to risk of contamination of the following reactions by the amplification product if the reactions are opened. The present study introduces a new closed-tube switchable complementation probes based PCR assay concept where two non-fluorescent probes form a fluorescent lanthanide chelate complex in the presence of the target DNA. In this dual-probe PCR assay method one oligonucleotide probe carries a non-fluorescent lanthanide chelate and another probe a light absorbing antenna ligand. The fluorescent lanthanide chelate complex is formed only when the non-fluorescent probes are hybridized to adjacent positions into the target DNA bringing the reporter moieties in close proximity. The complex is formed by self-assembled lanthanide chelate complementation where the antenna ligand is coordinated to the lanthanide ion captured in the chelate. The complementation probes based assays with time-resolved fluorescence measurement showed low background signal level and hence, relatively high nucleic acid detection sensitivity (low picomolar target concentration). Different lanthanide chelate structures were explored and a new cyclic seven dentate lanthanide chelate was found suitable for complementation probe method. It was also found to resist relatively high PCR reaction temperatures, which was essential for the PCR assay applications. A seven-dentate chelate with two unoccupied coordination sites must be used instead of a more stable eight- or nine-dentate chelate because the antenna ligand needs to be coordinated to the free coordination sites of the lanthanide ion. The previously used linear seven-dentate lanthanide chelate was found to be unstable in PCR conditions and hence, the new cyclic chelate was needed. The complementation probe PCR assay method showed high signal-to-background ratio up to 300 due to a low background fluorescence level and the results (threshold cycles) in real-time PCR were reached approximately 6 amplification cycles earlier compared to the commonly used FRET-based closed-tube PCR method. The suitability of the complementation probe method for different nucleic acid assay applications was studied. 1) A duplex complementation probe C. trachomatis PCR assay with a simple 10-minute urine sample preparation was developed to study suitability of the method for clinical diagnostics. The performance of the C. trachomatis assay was equal to the commercial C. trachomatis nucleic acid amplification assay containing more complex sample preparation based on DNA extraction. 2) A PCR assay for the detection of HLA-DQA1*05 allele, that is used to predict the risk of type 1 diabetes, was developed to study the performance of the method in genotyping. A simple blood sample preparation was used where the nucleic acids were released from dried blood sample punches using high temperature and alkaline reaction conditions. The complementation probe HLA-DQA1*05 PCR assay showed good genotyping performance correlating 100% with the routinely used heterogenous reference assay. 3) To study the suitability of the complementation probe method for direct measurement of the target organism, e.g., in the culture media, the complementation probes were applied to amplificationfree closed-tube bacteriophage quantification by measuring M13 bacteriophage ssDNA. A low picomolar bacteriophage concentration was detected in a rapid 20- minute assay. The assay provides a quick and reliable alternative to the commonly used and relatively unreliable UV-photometry and time-consuming culture based bacteriophage detection methods and indicates that the method could also be used for direct measurement of other micro-organisms. The complementation probe PCR method has a low background signal level leading to a high signal-to-background ratio and relatively sensitive nucleic acid detection. The method is compatible with simple sample preparation and it was shown to tolerate residues of urine, blood, bacteria and bacterial culture media. The common trend in nucleic acid diagnostics is to create easy-to-use assays suitable for rapid near patient analysis. The complementation probe PCR assays with a brief sample preparation should be relatively easy to automate and hence, would allow the development of highperformance nucleic acid amplification assays with a short overall assay time.

On Commutation and Conjugacy of Rational Languages and the Fixed Point Method

The research on language equations has been active during last decades. Compared to the equations on words the equations on languages are much more difficult to solve. Even very simple equations that are easy to solve for words can be very hard for languages. In this thesis we study two of such equations, namely commutation and conjugacy equations. We study these equations on some limited special cases and compare some of these results to the solutions of corresponding equations on words. For both equations we study the maximal solutions, the centralizer and the conjugator. We present a fixed point method that we can use to search these maximal solutions and analyze the reasons why this method is not successful for all languages. We give also several examples to illustrate the behaviour of this method.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

The future of branded sportswear store formats in Germany 2030: Four images of the future

A fast changing dynamic business environment is becoming a norm today in different areas, including retailing. The aims of this study are to explore existing store formats of branded sportswear retailing and their characteristics, and to identify the trends which might shape their future. The ultimate goal, however, is to create and analyze images of the future of branded sportswear retailing in Germany 2030 by applying the methods of futures studies. As theoretical background, the cyclical theories of retail evolution have been used. Empirical material is obtained by conducting a Disaggregative Policy Delphi method based study, the aim of which is to obtain well–argued qualitative and quantitative information from experts about store format development in order to create future images based on cluster analysis. Flagship stores, Concept stores, Factory Outlets, Pop-up stores, E-commerce and M-commerce represent the diversity of store formats existing in Germany today. They have different aims, roles, and advantages which retailers try to leverage. However such trends as multichannel integration, technological enhancements, growing popularity of online channels, switching customer behaviors, customization and personalization, and economic turbulence might shape the future of sportswear retailing. Four future images constructed: “Multichannel Integration”, “Smart and Personal”, “Consumer Diversification”, and “Always Online” – describe alternative futures of German branded sportswear store formats in 2030 based on different trends, assumptions, hopes and fears. They also point out uncertainties in retailing such as cannibalization of channels, the growing power and expectations of consumers, the complexity of multichannel synergies, and the switching customer behavior. Constructed future images, thus, provide readers with an opportunity to imagine and explore alternative states of the future of branded sportswear store formats in Germany 2030. They could serve well as a tool to communicate the results to decision–makers, compare them, and to analyze to inspire and direct actions for a better future tomorrow.

Vendor Managed Inventory: the Critical Success Factors from the Manufacturer Point of View

Yritykset ovat pakotettuja erilaisiin yhteistyömuotoihin pärjätäkseen kiristyvässä kilpailussa. Yhteistyösuhteet kulkevat eri nimillä riippuen teollisuuden alasta ja siitä, missä kohtaa toimitusketjua ne toteutuvat, mutta periaatteessa kaikki pohjautuvat samaan ideaan kuin Vendor Managed Inventory (VMI); varastoon jakysyntään liittyvä tieto jaetaan toimitusketjun eri osapuolien kesken, jotta tuotanto, jakelu ja varastonhallinta olisi mahdollista optimoida. Vendor Managed Inventory on ideana yksinkertainen, mutta vaatii onnistuakseen paljon. Perusolettamus on, että toimittajan on kyettävä hallinnoimaan asiakkaan varastoa paremmin kuin asiakas itse. Tämä ei kuitenkaan ole mahdollista ilman riittävää yhteistyötä, oikeanlaista informaatiota tai sopivia tuoteominaisuuksia. Tämän työn tarkoitus on esitellä kriittiset menestystekijät valmistajan kannalta, kun näkyvyys todelliseen kysyntään on heikko ja kyseessäolevat tuotteet ovat ominaisuuksiltaan toimintamalliin huonosti soveltuvia. VMItoimintamallin soveltuvuus matkapuhelimia valmistavan yrityksen liiketoimintaan, sekä sen vaikutus asiakasyhteistyöhön, kannattavuuteen ja toiminnan tehostamiseen on myös tutkittu.

Ohjelmistoyritysten liiketoimintamallit Kaakkois-Suomessa

Tutkielman tavoitteena on tunnistaa Kaakkois-Suomen alueella olevat ohjelmistoyritysten tyypilliset yritysryhmät ja kuvata niiden toimintaa. Tunnistamalla alueen ohjelmistoyrityksille ominaiset piirteet työ antaa myös pohjaa tulevien kehityskohteiden löytämisessä ja kehitystoimenpiteiden kohdistamisessa useisiin samantyyppisiin yrityksiin. Työn taustaksi esitellään ohjelmistoalaa ja ohjelmistoliiketoiminnan malleja, joiden pohjalta muodostetaan viitekehys alueen ohjelmistoyritysten empiiriseen tarkasteluun. Empiriaosuudessa tarkastellaan työn teoreettisessa osiossa esitettyjen liiketoimintamallien toteutumista Kaakkois-Suomessa ja ryhmitellään alueen ohjelmistoyritykset erottelevimpien tekijöiden avulla. Tutkimus on luonteeltaan kvantitatiivinen kokonaistutkimus Kaakkois-Suomen ohjelmistoyrityksistä, ja tutkimusotteeltaan deskriptiivinen eli kuvaileva. Tutkimusaineisto perustui tutkimusryhmän suorittamaan strukturoituun haastatteluun, jossa haastateltiin kaikkiaan 58 ohjelmistoyrityksen vastuuhenkilöitä. Tutkimustulosten perusteella alueelta pystyttiin tunnistamaan neljä toimintatavoiltaan erilaista ohjelmistoliiketoiminnan perustyyppiä: asiakaslähtöiset toimijat (26 toimipaikkaa), räätälöijät (14 toimipaikkaa), integroijat (10 toimipaikkaa) ja tuotteistajat (8 toimipaikkaa). Tulokset osoittavat, että perinteisten ohjelmistoalan liiketoimintamallien kuvaukset ja niistä tehtävät yleistykset antavat hyvän lähtökohdan ohjelmistoyritysten tarkasteluun. Kuitenkin perinteisten ohjelmistoalan liiketoimintamallien antama näkökulma on liian rajoittunut,jos halutaan tarkastella syvällisemmin ohjelmistoyritysten liiketoimintalogiikkaa.

Unlicensed Mobile Access Concept from Testing Point of View

Viime vuosikymmenien aikana kommunikaatioteknologiat ovat kehittyneet erittäin paljon. Uusia verkkoja, liityntätekniikoita, protokollia ja päätelaitteita on luotu alati kehittyvällä vauhdilla, eikä hidastumisen merkkejä ole näkyvissä. Varsinkin mobiilisovellukset ovat kasvattaneet markkinaosuuksiaan viime aikoina. Unlicensed MobileAccess (UMA) on uusi liityntätekniikka mobiilipäätelaitteille, joka mahdollistaa liitynnän GSM- runkoverkkoon WLAN- tai Bluetooth - tekniikoiden avulla. Tämä diplomityö keskittyy UMAan liittyviin teknologioihin, joita tarkastellaan lähemmin ensimmäisissä kappaleissa. Tavoitteena on esitellä, mitä UMA merkitsee, ja kuinka eri tekniikoita voidaan soveltaa sen toteutuksissa. Ennenkuin uusia teknologioita voidaan soveltaa kaupallisesti, täytyy niiden olla kokonaisvaltaisesti testattuja. Erilaisia testausmenetelmiä sovelletaan laitteistonja ohjelmiston testaukseen, mutta tavoite on kuitenkin sama, eli vähentää testattavan tuotteen epäluotettavuutta ja lisätä sen laatua. Vaikka UMA käsittääkin pääasiassa jo olemassa olevia tekniikoita, tuo se silti mukanaan uuden verkkoelementin ja kaksi uutta kommunikaatioprotokollaa. Ennen kuin mitään UMAa tukevia ratkaisuja voidaan tuoda markkinoille, monia erilaisia testausmenetelmiä on suoritettava, jotta varmistutaan uuden tuotteen oikeasta toiminnallisuudesta. Koska tämä diplomityö käsittelee uutta tekniikkaa, on myös testausmenetelmien yleisen testausteorian käsittelemiselle varattu oma kappale. Kappale esittelee erilaisia testauksen näkökulmia ja niihin perustuen rakennetaan myös testausohjelmisto. Tavoitteena on luoda ohjelmisto, jota voidaan käyttää UMA-RR protokollan toiminnan varmentamiseen kohdeympäristössä.

Kromatografisen erotusfaasin huokoskoon karakterisointi

Työssä tutkittiin sulfonoitujen polystyreenidivinyylibentseenirunkoisten geeli-, meso- ja makrohuokoistenioninvaihtohartsien rakennetta käyttäen useita eri karakterisointimenetelmiä. Lisäksi työssä tutkittiin hartsien huokoskoon vaikutusta aminohappojen kromatografisessa erotuksessa. Työn pääpaino oli hartsien huokoskoon ja huokoisuuden määrittämisessä. Sen selvittämiseksi käytettiin hyväksi elektronimikroskopiaa, typpiadsorptiomittauksia, sekä käänteistä kokoekskluusiokromatografiaa. Parhaat tulokset saatiin käänteisellä kokoekskluusiokromatografialla, joka perustuu erikokoisten dekstraanipolymeerien käyttöön mallimolekyyleinä. Menetelmä sopii meso- ja makrohuokoisuuden tutkimiseen, mutta sen heikkoutena on erittäin pitkä mittausaika. Menetelmä antaa myös huokoskokojakauman, mutta yhden hartsin mittaaminen voi kestää viikon. Menetelmää muutettiin siten, että käytettiin määritettävää huokoskokoaluetta kuvaavien kahden dekstraanipolymeerin seosta. Kromatografiset ajo-olosuhteet optimoitiin sellaisiksi, että injektoidussa seoksessa olevien dekstraanien vastehuiput erottuivat toisistaan. Tällöin voitiin luotettavasti määrittää tutkittavan stationaarifaasin suhteellinen huokoisuus. Tätä työssä kehitettyä nopeaa käänteiseen kokoekskluusiokromatografiaan perustuvaa menetelmää kutsutaan kaksipistemenetelmäksi. Hartsien sulfonihapporyhmien määrää ja jakautumista tutkittiin määrittämällä hartsien kationinvaihtokapasiteetti sekä tutkimalla hartsin pintaa konfokaali-Raman-spektroskopian avulla. Sulfonihapporyhmien ioninvaihtokyvyn selvittämiseksi mitattiin K+-muotoon muutetusta hartsista S/K-suhde poikkileikkauspinnasta. Tulosten perusteella hartsit olivat tasaisesti sulfonoituneet ja 95 % rikkiatomeista oli toimivassa ioninvaihtoryhmässä. Aminohappojen erotuksessa malliaineina oli lysiini, seriini ja tryptofaani. Hartsi oli NH4+-muodossa ja petitilavuus oli 91 mL. Eluenttina käytettiin vettä, jonka pH oli 10. Paras tulos saatiin virtausnopeudella 0,1 mL/min, jolla kaikki kolme aminohappoa erottuivat toisistaan Finex Oy:n mesohuokoisella KEF78-hartsilla. Muilla tutkituilla hartseilla kaikki kolme aminohappoa eivät missään ajo-olosuhteissa erottuneet täysin.

Palveluhankintojen analysointi ja mittaaminen, case Stora Enso Saimaa Services Oy

Tutkimuksen tavoitteena oli luoda Stora Enso Saimaa Services Oy:lle palveluhankintojen suorituskyvyn mittaristo Balanced Scorecardin avulla. Yrityksen palveluhankintakentän kirjavuuden vuoksi työ rajattiin koskemaan vain Etelä-Karjalan Yrityksiltä (= EKY) ostettavia kunnossapitopalveluja. Mittariston muodostamisen lähtökohtana oli hankintatoimen strateginen tavoite, kokonaiskustannusten alentaminen. Tämä tavoite konkretisoituu parhaiten hankintojen elinkaarikustannusten minimoimisena. Työssä käytettiin kvalitatiivista tutkimusmenetelmää. Tutkimuskohdetta analysoitiin tapaustutkimusmenetelmällä. Aineisto kerättiin sisäisille asiakkaille suunnatulla puolistrukturoidulla haastatteluilla, ostajien ajankäytönseurantakyselyllä sekä osallistuvalla havainnoinnilla. Haastatteluja tehtiin 10 ja kyselyjä 6. Palveluhankintojen elinkaarikustannusten ja mittaamisen osalta on tehty tutkimuksia hyvin vähän. EKY-palveluhankintoihin onnistuttiin kuitenkin luomaan tasapainotettu mittaristo palvelujen erityispiirteet huomioiden. EKY-elinkaarikustannusanalysoinnissa keskityttiin palveluhankintojen keskeisiin kustannuskomponentteihin kuten transaktiokustannusteoriaan, hintojen määräytymiseen ja huonon laadun kustannuksiin. Näiden pohjalta kriittisiksi palveluhankintojen menestystekijöiksi nousivat mm. ostajien ajankäytön suuntaaminen strategisiin työtehtäviin, hintojen hallinta sekä toimittajien laadun arviointi. Nämä tekijät muotoiltiin EKY-palveluhankintojen tuloskorttiin ja niihin valittiin hankintatoimen mittausmalleista sopivat suorituskyvyn mittarit. Mittarit jaettiin EKY-palveluhankintoihin määriteltyihin neljään näkökulmaan Balanced Scorecard -prosessin mukaisesti.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Technology selection and group decision support systems: Case studies on supporting strategic technology selection processes

The objective of the dissertation is to increase understanding and knowledge in the field where group decision support system (GDSS) and technology selection research overlap in the strategic sense. The purpose is to develop pragmatic, unique and competent management practices and processes for strategic technology assessment and selection from the whole company's point of view. The combination of the GDSS and technology selection is approached from the points of view of the core competence concept, the lead user -method, and different technology types. In this research the aim is to find out how the GDSS contributes to the technology selection process, what aspects should be considered when selecting technologies to be developed or acquired, and what advantages and restrictions the GDSS has in the selection processes. These research objectives are discussed on the basis of experiences and findings in real life selection meetings. The research has been mainly carried outwith constructive, case study research methods. The study contributes novel ideas to the present knowledge and prior literature on the GDSS and technology selection arena. Academic and pragmatic research has been conducted in four areas: 1) the potential benefits of the group support system with the lead user -method,where the need assessment process is positioned as information gathering for the selection of wireless technology development projects; 2) integrated technology selection and core competencies management processes both in theory and in practice; 3) potential benefits of the group decision support system in the technology selection processes of different technology types; and 4) linkages between technology selection and R&D project selection in innovative product development networks. New type of knowledge and understanding has been created on the practical utilization of the GDSS in technology selection decisions. The study demonstrates that technology selection requires close cooperation between differentdepartments, functions, and strategic business units in order to gather the best knowledge for the decision making. The GDSS is proved to be an effective way to promote communication and co-operation between the selectors. The constructs developed in this study have been tested in many industry fields, for example in information and communication, forest, telecommunication, metal, software, and miscellaneous industries, as well as in non-profit organizations. The pragmatic results in these organizations are some of the most relevant proofs that confirm the scientific contribution of the study, according to the principles of the constructive research approach.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.