The Possibilities and Dosimetric Limitations of MLC-Based Intensity-Modulated Radiotherapy Delivery and Optimization Techniques

The use of intensity-modulated radiotherapy (IMRT) has increased extensively in the modern radiotherapy (RT) treatments over the past two decades. Radiation dose distributions can be delivered with higher conformality with IMRT when compared to the conventional 3D-conformal radiotherapy (3D-CRT). Higher conformality and target coverage increases the probability of tumour control and decreases the normal tissue complications. The primary goal of this work is to improve and evaluate the accuracy, efficiency and delivery techniques of RT treatments by using IMRT. This study evaluated the dosimetric limitations and possibilities of IMRT in small (treatments of head-and-neck, prostate and lung cancer) and large volumes (primitive neuroectodermal tumours). The dose coverage of target volumes and the sparing of critical organs were increased with IMRT when compared to 3D-CRT. The developed split field IMRT technique was found to be safe and accurate method in craniospinal irradiations. By using IMRT in simultaneous integrated boosting of biologically defined target volumes of localized prostate cancer high doses were achievable with only small increase in the treatment complexity. Biological plan optimization increased the probability of uncomplicated control on average by 28% when compared to standard IMRT delivery. Unfortunately IMRT carries also some drawbacks. In IMRT the beam modulation is realized by splitting a large radiation field to small apertures. The smaller the beam apertures are the larger the rebuild-up and rebuild-down effects are at the tissue interfaces. The limitations to use IMRT with small apertures in the treatments of small lung tumours were investigated with dosimetric film measurements. The results confirmed that the peripheral doses of the small lung tumours were decreased as the effective field size was decreased. The studied calculation algorithms were not able to model the dose deficiency of the tumours accurately. The use of small sliding window apertures of 2 mm and 4 mm decreased the tumour peripheral dose by 6% when compared to 3D-CRT treatment plan. A direct aperture based optimization (DABO) technique was examined as a solution to decrease the treatment complexity. The DABO IMRT technique was able to achieve treatment plans equivalent with the conventional IMRT fluence based optimization techniques in the concave head-and-neck target volumes. With DABO the effective field sizes were increased and the number of MUs was reduced with a factor of two. The optimality of a treatment plan and the therapeutic ratio can be further enhanced by using dose painting based on regional radiosensitivities imaged with functional imaging methods.

Competence Development and Capacity Building of Sawmill Enterprises in Kenya – A Human Resources Development Approach

The Kenyan forestry and sawmilling industry have been subject to a changing environment since 1999 when the industrial forest plantations were closed down. This has lowered raw material supply and it has affected and reduced the sawmill operations and the viability of the sawmill enterprises. The capacity of the 276 registered sawmills is not sufficient to fulfill sawn timber demand in Kenya. This is because of the technological degradation and lack of a qualified labor force, which were caused because of non-existent sawmilling education and further training in Kenya. Lack of competent sawmill workers has led to low raw material recovery, under utilization of resources and loss of employment. The objective of the work was to suggest models, methods and approaches for the competence and capacity development of the Kenyan sawmilling industry, sawmills and their workers. A nationwide field survey, interviews, questionnaire and literature review was used for data collection to find out the sawmills’ competence development areas and to suggest models and methods for their capacity building. The sampling frame included 22 sawmills that represented 72,5% of all the registered sawmills in Kenya. The results confirmed that the sawmills’ technological level was backwards, productivity low, raw material recovery unacceptable and workers’ professional education low. The future challenges will be how to establish the sawmills’ capacity building and workers’ competence development. Sawmilling industry development requires various actions through new development models and approaches. Activities should be started for technological development and workers’ competence development. This requires re-starting of vocational training in sawmilling and the establishment of more effective co-operation between the sawmills and their stakeholder groups. In competence development the Enterprise Competence Management Model of Nurminen (2007) can be used, whereas the best training model and approach would be a practically oriented learning at work model in which the short courses, technical assistance and extension services would be the key functions.

Use of field measurements in fatigue analysis of forestry cranes

Tässä työssä on esitetty väsyttävän kuormituksen mittaamiseen ja mittausdatan jälkikäsittelyyn sekä väsymismitoitukseen liittyviä menetelmiä. Menetelmien sovelluskohteena oli metsäkoneen kuormain, joka on väsyttävästi kuormitettu hitsattu rakenne. Teoriaosassa on kuvattu väsymisilmiötä ja väsymismitoitusmenetelmiä sekä kuormitusten tunnistamiseen ja mittausten jälkikäsittelyyn liittyviä menetelmiä. Yleisimmin käytettyjen väsymismitoitusmenetelmien rinnalle on esitetty luotettavuuteen perustuvaa väsymismitoitusmenetelmää. Kuormainten suunnittelussa on keveys- j a kestoikävaatimusten takia erityisen suuri merkitys väsymisen huomioimisella. Rakenteille on ominaista tietyt toiminnan kannalta välttämättömät hitsatut yksityiskohdat, jotka usein määräävät koko rakenteen kestoiän. Koska nämä ongelmakohdat pystytään useimmiten tunnistamaan jo suunnitteluvaiheessa, voidaan yksityiskohtien muotoilulla usein parantaa huomattavasti koko rakenteen kestoikää. Näiden yksityiskohtien optimointi on osittain mahdollista toteuttaa ilman kuormituskertymätietoa, mutta useimmiten kuormitusten tunnistaminen on edellytys parhaan ratkaisun löytymiselle. Tällöin toistaiseksi paras keino todellisen väsyttävän kuormituksen tunnistamiseksi on pitkäaikaiset kenttämittaukset. Kenttämittauksilla selvitetään rakenteeseen kohdistuvat kuormitukset venymäliuskojen avulla. Kuormitusten tunnistamisella on erityisen suuri merkitys kun halutaan määrittää rakenteen kestoikä. Väsyminen ja väsyttävä kuormitus ovat kuitenkin tilastollisia muuttujia j a yksittäiselle rakenteelle ei ole mahdollista määrittää tarkkaa k estoikää. Tilastollisia menetelmiä käyttäen on kuitenkin mahdollista määrittää rakenteen vaurioitumisriski. Laskettaessa vaurioitumisriskiä suurelle määrälle yksittäisiä rakenteita voidaan muodostaa tarkkojakin ennusteita mahdollisten vaurioiden lukumäärästä. Tällöin kuormituskertymätiedosta voi olla tavanomaisen suunnittelun lisäksi laajempaa hyötyä esimerkiksi takuukäsittelyssä. Tässä työssä on sovellettu esitettyjä teorioita käytännössä metsäkoneen harvesterin puomiston väsymistarkasteluun. Kyseisen rakenteen kuormituksia mitattiin kahden viikon aikana yhteensä 35 tuntia, jonka perusteella laskettiin väsyttävän kuormituksen tilastollinen jakauma esimerkkitapaukselle. Mittauksen perusteella ei voitu tehdä kuitenkaan johtopäätöksiä tuotteen koko elinkaaren kuormituksista eikä muiden samanlaisten tuotteiden kuormituksista, koska mitattu otos oli suhteellisen lyhyt ja rajoittui vain yhteen käyttäjään ja muutamaan käyttökohteeseen. Menetelmien testaamiseksi kyseinen otos oli kuitenkin riittävä. Kuormituskertymätietoa käytettiin hyväksi myös laatumääritysten muodostamisessaesimerkkitapaukselle. Murtumismekaniikkaan perustuvalla menetelmällä arvioitiinharvesteripilarin valun mahdollisten valuvirheiden suurin sallittu koko. Luotettavuuteen pohjautuvan mitoitusmenettelyn tarve näyttää olevanlisääntymässä, joten pitkäaikaisten kenttämittausten tehokas hyödyntäminen tulee olemaan keskeinen osa väsymismitoitusta lähitulevaisuudessa. Menetelmiä olisi mahdollista tehostaa yhdistämällä kuormituskertymään erilaisia kuormitusten suhteen riippuvia tunnettuja suureita kuten käsiteltävän puun halkaisija. Todellisettuotekohtaiset tilastolliset jakaumat kuormituksista voitaisiin muodostaa mahdollisesti tehokkaammin, jos esimerkiksi kuormitusten riippuvuus metsätyypistä pystyttäisiin ensin määrittämään.

On the innovation capacity of technologyrelated knowledge-intensive business services. A case study of the technology and engineering consulting (TEC) sector in Singapore

Even though the research on innovation in services has expanded remarkably especially during the past two decades, there is still a need to increase understanding on the special characteristics of service innovation. In addition to studying innovation in service companies and industries, research has also recently focused more on services in innovation, as especially the significance of so-called knowledge intensive business services (KIBS) for the competitive edge of their clients, othercompanies, regions and even nations has been proved in several previous studies. This study focuses on studying technology-based KIBS firms, and technology andengineering consulting (TEC) sector in particular. These firms have multiple roles in innovation systems, and thus, there is also a need for in-depth studies that increase knowledge about the types and dimensions of service innovations as well as underlying mechanisms and procedures which make the innovations successful. The main aim of this study is to generate new knowledge in the fragmented research field of service innovation management by recognizing the different typesof innovations in TEC services and some of the enablers of and barriers to innovation capacity in the field, especially from the knowledge management perspective. The study also aims to shed light on some of the existing routines and new constructions needed for enhancing service innovation and knowledge processing activities in KIBS companies of the TEC sector. The main samples of data in this research include literature reviews and public data sources, and a qualitative research approach with exploratory case studies conducted with the help of the interviews at technology consulting companies in Singapore in 2006. These complement the qualitative interview data gathered previously in Finland during a larger research project in the years 2004-2005. The data is also supplemented by a survey conducted in Singapore. The respondents for the survey by Tan (2007) were technology consulting companies who operate in the Singapore region. The purpose ofthe quantitative part of the study was to validate and further examine specificaspects such as the influence of knowledge management activities on innovativeness and different types of service innovations, in which the technology consultancies are involved. Singapore is known as a South-east Asian knowledge hub and is thus a significant research area where several multinational knowledge-intensive service firms operate. Typically, the service innovations identified in the studied TEC firms were formed by several dimensions of innovations. In addition to technological aspects, innovations were, for instance, related to new client interfaces and service delivery processes. The main enablers of and barriers to innovation seem to be partly similar in Singaporean firms as compared to the earlier study of Finnish TEC firms. Empirical studies also brought forth the significance of various sources of knowledge and knowledge processing activities as themain driving forces of service innovation in technology-related KIBS firms. A framework was also developed to study the effect of knowledge processing capabilities as well as some moderators on the innovativeness of TEC firms. Especially efficient knowledge acquisition and environmental dynamism seem to influence the innovativeness of TEC firms positively. The results of the study also contributeto the present service innovation literature by focusing more on 'innovation within KIBs' rather than 'innovation through KIBS', which has been the typical viewpoint stressed in the previous literature. Additionally, the study provides several possibilities for further research.

FPGA-Based Control Design for Power Electronic Applications

Tehoelektoniikkalaitteella tarkoitetaan ohjaus- ja säätöjärjestelmää, jolla sähköä muokataan saatavilla olevasta muodosta haluttuun uuteen muotoon ja samalla hallitaan sähköisen tehon virtausta lähteestä käyttökohteeseen. Tämä siis eroaa signaalielektroniikasta, jossa sähköllä tyypillisesti siirretään tietoa hyödyntäen eri tiloja. Tehoelektroniikkalaitteita vertailtaessa katsotaan yleensä niiden luotettavuutta, kokoa, tehokkuutta, säätötarkkuutta ja tietysti hintaa. Tyypillisiä tehoelektroniikkalaitteita ovat taajuudenmuuttajat, UPS (Uninterruptible Power Supply) -laitteet, hitsauskoneet, induktiokuumentimet sekä erilaiset teholähteet. Perinteisesti näiden laitteiden ohjaus toteutetaan käyttäen mikroprosessoreja, ASIC- (Application Specific Integrated Circuit) tai IC (Intergrated Circuit) -piirejä sekä analogisia säätimiä. Tässä tutkimuksessa on analysoitu FPGA (Field Programmable Gate Array) -piirien soveltuvuutta tehoelektroniikan ohjaukseen. FPGA-piirien rakenne muodostuu erilaisista loogisista elementeistä ja niiden välisistä yhdysjohdoista.Loogiset elementit ovat porttipiirejä ja kiikkuja. Yhdysjohdot ja loogiset elementit ovat piirissä kiinteitä eikä koostumusta tai lukumäärää voi jälkikäteen muuttaa. Ohjelmoitavuus syntyy elementtien välisistä liitännöistä. Piirissä on lukuisia, jopa miljoonia kytkimiä, joiden asento voidaan asettaa. Siten piirin peruselementeistä voidaan muodostaa lukematon määrä erilaisia toiminnallisia kokonaisuuksia. FPGA-piirejä on pitkään käytetty kommunikointialan tuotteissa ja siksi niiden kehitys on viime vuosina ollut nopeaa. Samalla hinnat ovat pudonneet. Tästä johtuen FPGA-piiristä on tullut kiinnostava vaihtoehto myös tehoelektroniikkalaitteiden ohjaukseen. Väitöstyössä FPGA-piirien käytön soveltuvuutta on tutkittu käyttäen kahta vaativaa ja erilaista käytännön tehoelektroniikkalaitetta: taajuudenmuuttajaa ja hitsauskonetta. Molempiin testikohteisiin rakennettiin alan suomalaisten teollisuusyritysten kanssa soveltuvat prototyypit,joiden ohjauselektroniikka muutettiin FPGA-pohjaiseksi. Lisäksi kehitettiin tätä uutta tekniikkaa hyödyntävät uudentyyppiset ohjausmenetelmät. Prototyyppien toimivuutta verrattiin vastaaviin perinteisillä menetelmillä ohjattuihin kaupallisiin tuotteisiin ja havaittiin FPGA-piirien mahdollistaman rinnakkaisen laskennantuomat edut molempien tehoelektroniikkalaitteiden toimivuudessa. Työssä on myösesitetty uusia menetelmiä ja työkaluja FPGA-pohjaisen säätöjärjestelmän kehitykseen ja testaukseen. Esitetyillä menetelmillä tuotteiden kehitys saadaan mahdollisimman nopeaksi ja tehokkaaksi. Lisäksi työssä on kehitetty FPGA:n sisäinen ohjaus- ja kommunikointiväylärakenne, joka palvelee tehoelektroniikkalaitteiden ohjaussovelluksia. Uusi kommunikointirakenne edistää lisäksi jo tehtyjen osajärjestelmien uudelleen käytettävyyttä tulevissa sovelluksissa ja tuotesukupolvissa.

Evaluation of GPRS Radio Link Control Layer in Weak RF Field

General Packet Radio Service (GPRS) mahdollistaa pakettimuotoisen tiedonsiirron GSM-verkossa. Se tarjoaa yhteyden pakettidataverkkoihin, nostaen samalla tiedonsiirtonopeutta radiorajapinnassa. Radioresurssit ovat varattuna vain silloin kun on jotain lähetettävää, tehden täten radioresurssien käytön paljon tehokkaammaksi. Tämä diplomityö keskittyy GPRS protokollaan ja erityisesti sen datapinossa olevaan Radio Link Control (RLC) kerrokseen. RLC-kerros huolehtii GPRS- puhelimen ja tukiaseman välisen yhteyden luotettavuudesta. Työn tavoitteena on tutkia RLC-kerroksen toiminnallisuutta ja sen luotettavuutta heikossa kentässä, sekä selvittää heikon kentän vaikutusta uudelleenlähetyksiin. Työn tuloksena saadaan arvio signaalin voimakkuuden sekä uudelleen lähetysten vaikutuksesta GPRS:n datansiirtonopeuteen. Tämä työ käsittelee myös lyhyesti GSM-järjestelmää, koska lukijan on näin helpompaa ymmärtää myös GPRS-järjestelmän vaatimia teknisiä muutoksia. Tämä diplomityö on tehty osana Nokia Matkapuhelimet Oyj:ssä käynnissä olevaa GPRS tuotekehitysprojektia. Työn tuloksia käytetään testauksen tukena ja niitä on käytetty apuna RLC-kerroksen luotettavuustestauksen suunnittelussa.

Evolution of Ba and Role of Absorptive Capacity in Collaboration between MNCs and Chinese Universities in China

During the recent years, collaboration with Chinese universities has aroused growing interest among multinational companies (MNCs). Cross-cultural university-industry (U-I) collaboration creates various challenges in collaborative knowledge creation and innovation due to the differences e.g. between university and company motivation, objectives and activities. Also different values, norms, and means of actions result often in collisions and misunderstandings. This thesis examines the establishment of the relationships and the evolution of the collaboration between MNCs and Chinese universities. Empirical findings underscore that the partners in collaboration are required to possess research interest as well as capability to acquire, assimilate and exploit new external knowledge. Time and communication have a critical role in the evolution of the collaboration. In China the personal relationships, guanxi, play an important role. Collaborative knowledge creation requires a platform, Ba, which enables the creation of common understanding, commitment, trust and mutual respect. Empirical data has been collected through interviewing company experts and academe of Chinese universities from ICT and forest industries as well as attending panel discussions and meetings with the experts from the field of study.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Enhancing absorptive capacity in a non-research and development. An action research approach to converting individual observations into organisational awareness

The ability to recognize potential knowledge and convert it into business opportunities is one of the key factors of renewal in uncertain environments. This thesis examines absorptive capacity in the context of non-research and development innovation, with a primary focus on the social interaction that facilitates the absorption of knowledge. It proposes that everyone is and should be entitled to take part in the social interaction that shapes individual observations into innovations. Both innovation and absorptive capacity have been traditionally related to research and development departments and institutions. These innovations need to be adopted and adapted by others. This so-called waterfall model of innovations is only one aspect of new knowledge generation and innovation. In addition to this Science–Technology–Innovation perspective, more attention has been recently paid to the Doing–Using–Interacting mode of generating new knowledge and innovations. The amount of literature on absorptive capacity is vast, yet the concept is reified. The greater part of the literature links absorptive capacity to research and development departments. Some publications have focused on the nature of absorptive capacity in practice and the role of social interaction in enhancing it. Recent literature on absorptive capacity calls for studies that shed light on the relationship between individual absorptive capacity and organisational absorptive capacity. There has also been a call to examine absorptive capacity in non-research and development environments. Drawing on the literature on employee-driven innovation and social capital, this thesis looks at how individual observations and ideas are converted into something that an organisation can use. The critical phases of absorptive capacity, during which the ideas of individuals are incorporated into a group context, are assimilation and transformation. These two phases are seen as complementary: whereas assimilation is the application of easy-to-accept knowledge, transformation challenges the current way of thinking. The two require distinct kinds of social interaction and practices. The results of this study can been crystallised thus: “Enhancing absorptive capacity in practicebased non-research and development context is to organise the optimal circumstances for social interaction. Every individual is a potential source of signals leading to innovations. The individual, thus, recognises opportunities and acquires signals. Through the social interaction processes of assimilation and transformation, these signals are processed into the organisation’s reality and language. The conditions of creative social capital facilitate the interplay between assimilation and transformation. An organisation that strives for employee-driven innovation gains the benefits of a broader surface for opportunity recognition and faster absorption.” If organisations and managers become more aware of the benefits of enhancing absorptive capacity in practice, they have reason to assign resources to those practices that facilitate the creation of absorptive capacity. By recognising the underlying social mechanisms and structural features that lead either to assimilation or transformation, it is easier to balance between renewal and effective operations.

Acidic dissolution of iron oxides and regeneration of a ceramic filter medium

The dewatering of iron ore concentrates requires large capacity in addition to producing a cake with low moisture content. Such large processes are commonly energy intensive and means to lower the specific energy consumption are needed. Ceramic capillary action disc filters incorporate a novel filter medium enabling the harnessing of capillary action, which results in decreased energy consumption in comparison to traditional filtration technologies. As another benefit, the filter medium is mechanically and chemically more durable than, for example, filter cloths and can, thus, withstand harsh operating conditions and possible regeneration better than other types of filter media. In iron ore dewatering, the regeneration of the filter medium is done through a combination of several techniques: (1) backwashing, (2) ultrasonic cleaning, and (3) acid regeneration. Although it is commonly acknowledged that the filter medium is affected by slurry particles and extraneous compounds, published research, especially in the field of dewatering of mineral concentrates, is scarce. Whereas the regenerative effect of backwashing and ultrasound are more or less mechanical, regeneration with acids is based on chemistry. The chemistry behind the acid regeneration is, naturally, dissolution. The dissolution of iron oxide particles has been extensively studied over several decades but those studies may not necessarily be directly applicable in the regeneration of the filter medium which has undergone interactions with the slurry components. The aim of this thesis was to investigate if free particle dissolution indeed correlates with the regeneration of the filter medium. For this purpose, both free particle dissolution and dissolution of surface adhered particles were studied. The focus was on acidic dissolution of iron oxide particles and on the study of the ceramic filter medium used in the dewatering of iron ore concentrates. The free particle dissolution experiments show that the solubility of synthetic fine grained iron oxide particles in oxalic acid could be explained through linear models accounting for the effects of temperature and acid concentration, whereas the dissolution of a natural magnetite is not so easily explained by such models. In addition, the kinetic experiments performed both support and contradict the work of previous authors: the suitable kinetic model here supports previous research suggesting solid state reduction to be the reaction mechanism of hematite dissolution but the formation of a stable iron oxalate is not supported by the results of this research. Several other dissolution mechanisms have also been suggested for iron oxide dissolution in oxalic acid, indicating that the details of oxalate promoted reductive dissolution are not yet agreed and, in this respect, this research offers added value to the community. The results of the regeneration experiments with the ceramic filter media show that oxalic acid is highly effective in removing iron oxide particles from the surface of the filter medium. The dissolution of those particles did not, however, exhibit the expected behaviour, i.e. complete dissolution. The results of this thesis show that although the regeneration of the ceramic filter medium with acids incorporates the dissolution of slurry particles from the surface of the filter medium, the regeneration cannot be assessed purely based upon free particle dissolution. A steady state, dependent on temperature and on the acid concentration, was observed in the dissolution of particles from the surface even though the limit of solubility of free iron oxide particles had not been reached. Both the regeneration capacity and efficiency, with regards to the removal of iron oxide particles, was found to be temperature dependent, but was not affected by the acid concentration. This observation further suggests that the removal of the surface adhered particles does not follow the dissolution of free particles, which do exhibit a dependency on the acid concentration. In addition, changes in the permeability and in the pore structure of the filter medium were still observed after the bulk concentration of dissolved iron had reached a steady state. Consequently, the regeneration of the filter medium continued after the dissolution of particles from the surface had ceased. This observation suggests that internal changes take place at the final stages of regeneration. The regeneration process could, in theory, be divided into two, possibly overlapping, stages: (1) dissolution of surface-adhered particles, and (2) dissolution of extraneous compounds from within the pore structure. In addition to the fundamental knowledge generated during this thesis, tools to assess the effects of parameters on the regeneration of the ceramic filter medium are needed. It has become clear that the same tools used to estimate the dissolution of free particles cannot be used to estimate the regeneration of a filter medium unless only a robust characterisation of the order of regeneration efficiency is needed.

Bus bar aeolian vibration field tests

Large amplitude bus bar aeolian vibration may lead to post insulator damage. Different damping applications are used to decrease the risk of large amplitude aeolian vibration. In this paper the post insulator load caused by the bus bar aeolian vibration and the effect of damping methods are evaluated. The effects of three types of bus bar connectors and three types of primary structures are studied. Two actual damping devices, damping cable and their combinations are studied. The post insulator loads are studied with strain gage based custom made force sensors installed on the both ends of the post insulator and with the displacement sensor installed on the midpoint of the bus bar. The post insulator loads are calculated from the strain values and the damping properties are determined from the displacement history. The bus bar is deflected with a hanging weight. The weight is released and the bus bar is left to free damped vibration. Both actual bus bar vibration dampers RIBE and SBI were very effective against the aeolian vibration. Combining vibration damper with damping cable will increase the damping ratio but it may be unnecessary considering the extra effort. Bus bar connector type or primary structure have no effect on the vertical load. The bending moment at the post insulator with double sided bus bar connector is significantly higher than at the post insulator with single sided bus bar connector. No reliable conclusions about bus bar connector type effect can be done, but the roller bearing type or central bearing type connector may reduce the bending moment. The RHS steel frame as primary structure may increase the bending moment peak values since it is the least rigid primary structure type and it may start to vibrate as a response to the awakening force of the vibrating bus bar.