Advanced control methods for reducing nitrogen oxides in a fluidized bed boiler

Tämän työn tarkoituksena oli löytää keinoja erään leijukerroskattilan typenoksidipäästöjen vähentämiseksi. Koska päästöt olivat jo alunperin alhaiset leijukerrostekniikan ja hybridin SNCR/SCR –typenpoistolaitteiston ansiosta, päätettiin päästöjä lähteä vähentämään parantamalla ammoniakkiruiskutuksen säätöä. Alkuperäinen ammoniakkiruiskutuksen säätö oli liian hidas, jotta satunnaisten häiriöiden aiheuttamat typenoksidipiikit olisi pystytty poistamaan. Ammoniakkiruiskutusta parannettiin lisäämällä jokaiseen ammoniakkilinjaan mäntäpumput, joiden avulla ammoniakkia voidaan syöttää sinne, missä sitä eniten tarvitaan. Ammoniakkiruiskutuksen säätöön kehitettiin uusi sumeaan logiikkaan perustuva säätäjä. Myös muita kehittyneitä säätömenetelmiä kuten neuroverkkoa hyödynnettiin säätäjän kehityksessä. Ammoniakkiruiskutuksen säätäjää testattiin menestyksekkäästi Ruotsissa Brista Kraftin Märstassa sijaitsevalla voimalaitoksella

Control methods for arc welding power supplies

Welding is one of the most important process of modern industry. Welding technology is used in the manufacture and repair a wide variety of products from different metals and alloys. In this thesis the different aspects of arc welding were discussed, such as stability and control of welding arc, power supplies for arc welding (especially the welding inverters because it is the most modern welding power source). All parameters of power source have influence on the arc parameters and its by-turn influence on quality. The ways of control for arc welding inverter power sources have been considered. Calculations and modeling in Matlab/Simulink were done for PI control method. All parameters of power source have influence on the arc parameters and its by-turn influence on quality.

Novel force control methods in a teleoperation system of a hydraulic slider

The objective of the this research project is to develop a novel force control scheme for the teleoperation of a hydraulically driven manipulator, and to implement an ideal transparent mapping between human and machine interaction, and machine and task environment interaction. This master‘s thesis provides a preparatory study for the present research project. The research is limited into a single degree of freedom hydraulic slider with 6-DOF Phantom haptic device. The key contribution of the thesis is to set up the experimental rig including electromechanical haptic device, hydraulic servo and 6-DOF force sensor. The slider is firstly tested as a position servo by using previously developed intelligent switching control algorithm. Subsequently the teleoperated system is set up and the preliminary experiments are carried out. In addition to development of the single DOF experimental set up, methods such as passivity control in teleoperation are reviewed. The thesis also contains review of modeling of the servo slider in particular reference to the servo valve. Markov Chain Monte Carlo method is utilized in developing the robustness of the model in presence of noise.

Study of Control Methods of a High-Frequency Cycloconverter for Domestic Induction Heating Appliances

A high-frequency cyclonverter acts as a direct ac-to-ac power converter circuit that does not require a diode bidge rectifier. Bridgeless topology makes it possible to remove forward voltage drop losses that are present in a diode bridge. In addition, the on-state losses can be reduced to 1.5 times the on-state resistance of switches in half-bridge operation of the cycloconverter. A high-frequency cycloconverter is reviewed and the charging effect of the dc-capacitors in ``back-to-back'' or synchronous mode operation operation is analyzed. In addition, a control method is introduced for regulating dc-voltage of the ac-side capacitors in synchronous operation mode. The controller regulates the dc-capacitors and prevents switches from reaching overvoltage level. This can be accomplished by variating phase-shift between the upper and the lower gate signals. By adding phase-shift between the gate signal pairs, the charge stored in the energy storage capacitors can be discharged through the resonant load and substantially, the output resonant current amplitude can be improved. The above goals are analyzed and illustrated with simulation. Theory is supported with practical measurements where the proposed control method is implemented in an FPGA device and tested with a high-frequency cycloconverter using super-junction power MOSFETs as switching devices.

Power efficiency estimation and simulation of different control methods for the rotary screw compressor

Nowadays the energy efficiency has become one of the most concerned topics. Compressors are the equipment, which is very common in industry. Moreover, they tend to operate during long cycles and therefore even small decrease in power consumption can significantly reduce electricity costs during the year. And therefore it is important to investigate ways of increasing the energy efficiency of the compressors. In the thesis rotary screw compressor alongside with different control approaches is described. Simulation models for various control types of rotary screw compressor are developed. Analysis of laboratory equipment is conducted and results are compared with simulation. Suggestions of the real laboratory equipment improvement are given.

Pölynhallintamenetelmät rakentamisessa - tekninen toteutus ja menetelmien tehokkuus

Rakennustyömaa on yksi vaarallisimpia ja työolosuhteiltaan haastavimpia työpaikkoja. Sisävalmistusvaiheessa ongelmaksi muodostuu töiden tuottama pöly ja melu. Työmaan epäjärjestys ja likaisuus lisäävät tapaturmariskiä. Pölytöntä rakennustyömaata ei ole olemassa ja tästä syystä pölynhallinta muodostuu merkittäväksi tekijäksi pölyn leviämisen rajoittamisessa. Työn tavoitteena oli tutkia teknisiä pölynhallintakeinoja, joilla voidaan vähentää henkilökohtaisen suojauksen tarvetta rakennustyömailla. Pölynhallintaan työmailla voidaan vaikuttaa työtapojen ja -menetelmien valinnalla, töiden vaiheistuksella, kohdepoistoilla, osastoinnilla ja alipaineistuksella. Työssä oli tarkoitus myös verrata ja tutkia erilaisten ja eri työvaiheisiin tarkoitettujen pölynhallintalaitteistojen toimintaa ja niiden toimivuutta pölynhallinnassa. Tämä tutkimus toteutettiin Savocon Oy:n Kuopioon rakennettavan Turontähden rakennustyömaalla huhti- ja toukokuussa 2008. Tutkimusten perusteella tekniset pölynhallintakeinot toimivat kohtalaisen hyvin. Hiomalaitteissa pölynhallinta on tekninen ominaisuus, mutta sen toimivuus riippuu myös siitä, osaako työntekijä hyödyntää pölynhallintaa oikealla tavalla. Toimintaan vaikuttaa se, osaavatko laitteen käyttäjät asettaa imutehon sellaiseksi, että se on riittävän suuri poistamaan pölyn, mutta ei liian suuri haitatakseen työntekoa ja saaden aikaan heikkoa työnjälkeä. Oikeat laiteasetukset opitaan kokeilemalla. Imutehon säätömahdollisuus on erilaisten pintatasoitteiden myötä erityisen tärkeä laiteominaisuus. Timanttihiomalaitteilla saavutetut pölynpoistotehokkuudet olivat kaikki yli 97 prosenttia, kun niiden tehoa verrattiin ilman pölynpoistoa tapahtuvaan timanttihiontaan. Timanttihiontaa ei suositella tehtäväksi ilman pölynpoistotekniikkaa, sillä pölyntuotto on suurta ja pölypitoisuudet nousevat nopeasti hyvin suuriksi ja työntekijöiden altistus pölylle kasvaa. Ilmanpuhdistimien tehot riittivät pienen tilan ilman puhdistamiseen, mutta suurissa tiloissa ja suurissa pitoisuuksissa teho jäi riittämättömäksi. Oikein mitoitettuina ilmanpuhdistimia voidaan suositella kohdepoistolla toimivien laitteiden lisäksi huonetilaan puhdistamaan vähäiset hiukkaspäästöt, joita laitteista tulee. Teollisuusimurien valinnassa huomio tulee kiinnittää moottorin imutehoon, moottorin jäähdytyksen järjestelyyn, pölypussin materiaaliin ja pölypussin tyhjennysmekanismiin. Näillä on suuri merkitys siivoustyön pölyttömämpään lopputulokseen. Tämän työn käyttö markkinointitarkoituksessa ilman tekijän lupaa on kielletty.

Novel control, haptic and calibration methods for teleoperated electrohydraulic servo systems

The aim of this thesis is to propose a novel control method for teleoperated electrohydraulic servo systems that implements a reliable haptic sense between the human and manipulator interaction, and an ideal position control between the manipulator and the task environment interaction. The proposed method has the characteristics of a universal technique independent of the actual control algorithm and it can be applied with other suitable control methods as a real-time control strategy. The motivation to develop this control method is the necessity for a reliable real-time controller for teleoperated electrohydraulic servo systems that provides highly accurate position control based on joystick inputs with haptic capabilities. The contribution of the research is that the proposed control method combines a directed random search method and a real-time simulation to develop an intelligent controller in which each generation of parameters is tested on-line by the real-time simulator before being applied to the real process. The controller was evaluated on a hydraulic position servo system. The simulator of the hydraulic system was built based on Markov chain Monte Carlo (MCMC) method. A Particle Swarm Optimization algorithm combined with the foraging behavior of E. coli bacteria was utilized as the directed random search engine. The control strategy allows the operator to be plugged into the work environment dynamically and kinetically. This helps to ensure the system has haptic sense with high stability, without abstracting away the dynamics of the hydraulic system. The new control algorithm provides asymptotically exact tracking of both, the position and the contact force. In addition, this research proposes a novel method for re-calibration of multi-axis force/torque sensors. The method makes several improvements to traditional methods. It can be used without dismantling the sensor from its application and it requires smaller number of standard loads for calibration. It is also more cost efficient and faster in comparison to traditional calibration methods. The proposed method was developed in response to re-calibration issues with the force sensors utilized in teleoperated systems. The new approach aimed to avoid dismantling of the sensors from their applications for applying calibration. A major complication with many manipulators is the difficulty accessing them when they operate inside a non-accessible environment; especially if those environments are harsh; such as in radioactive areas. The proposed technique is based on design of experiment methodology. It has been successfully applied to different force/torque sensors and this research presents experimental validation of use of the calibration method with one of the force sensors which method has been applied to.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Sliding Mode Control for Switched Mode Power Supplies

Control applications of switched mode power supplies have been widely investigated. The main objective ofresearch and development (R&D) in this field is always to find the most suitable control method to be implemented in various DC/DC converter topologies. Inother words, the goal is to select a control method capable of improving the efficiency of the converter, reducing the effect of disturbances (line and load variation), lessening the effect of EMI (electro magnetic interference), and beingless effected by component variation. The main objective of this research work is to study different control methods implemented in switched mode power supplies namely (PID control, hysteresis control, adaptive control, current programmed control, variable structure control (VSC), and sliding mode control (SMC). The advantages and drawbacks of each control method are given. Two control methods, the PID and the SMC are selected and their effects on DC/DC (Buck, Boost, and Buck-Boost) converters are examined. Matlab/SimulinkTM is used to implement PID control method in DC/DC Buck converter and SMC in DC/DC (Buck, and Buck Boost) converters. For the prototype, operational amplifiers (op-amps) are used to implement PID control in DC/DC Buck converter. For SMC op-amps are implemented in DC/DC Buck converter and dSPACETM is used to control the DC/DC Buck-Boost converter. The SMC can be applied to the DC/DC (Buck, Boost, and Buck-Boost) converters. A comparison of the effects of the PID control and the SMC on the DC/DC Buck converter response in steady state, under line variations, load variations, and different component variations is performed. Also the Conducted RF-Emissions between the PID and SMC DC/DC Buck Converter are compared. The thesis shows that, in comparison with the PID control, the SMC provides better steady-state response, better dynamic response, less EMI, inherent order reduction, robustness against system uncertainty disturbances, and an implicit stability proof. Giving a better steady-state and dynamic response, the SMC is implemented in a DC/DC resonant converter. The half-wave zero current switching (HWZCS) DC/DC Buck converter is selected as a converter topology. A general guideline to select the tank component values, needed for the designing of a HWZCS DC/DC Buck, is obtained. The implementation of the SMC to a HWZCS DC/DC Buck converter is analysed. The converter response is investigated in the steady-state region and in the dynamic region.

Design and implementation of FPGA-based LQ control of active magnetic bearings

The need for high performance, high precision, and energy saving in rotating machinery demands an alternative solution to traditional bearings. Because of the contactless operation principle, the rotating machines employing active magnetic bearings (AMBs) provide many advantages over the traditional ones. The advantages such as contamination-free operation, low maintenance costs, high rotational speeds, low parasitic losses, programmable stiffness and damping, and vibration insulation come at expense of high cost, and complex technical solution. All these properties make the use of AMBs appropriate primarily for specific and highly demanding applications. High performance and high precision control requires model-based control methods and accurate models of the flexible rotor. In turn, complex models lead to high-order controllers and feature considerable computational burden. Fortunately, in the last few years the advancements in signal processing devices provide new perspective on the real-time control of AMBs. The design and the real-time digital implementation of the high-order LQ controllers, which focus on fast execution times, are the subjects of this work. In particular, the control design and implementation in the field programmable gate array (FPGA) circuits are investigated. The optimal design is guided by the physical constraints of the system for selecting the optimal weighting matrices. The plant model is complemented by augmenting appropriate disturbance models. The compensation of the force-field nonlinearities is proposed for decreasing the uncertainty of the actuator. A disturbance-observer-based unbalance compensation for canceling the magnetic force vibrations or vibrations in the measured positions is presented. The theoretical studies are verified by the practical experiments utilizing a custom-built laboratory test rig. The test rig uses a prototyping control platform developed in the scope of this work. To sum up, the work makes a step in the direction of an embedded single-chip FPGA-based controller of AMBs.

Kuivurin pölynhallintajärjestelmä

Lämminilmakuivaus on viljan kuivaamisen menetelmistä ylivoimaisesti käytetyin. Siinä kuivurissa olevan viljakerroksen läpi puhalletaan lämmintä ilmaa, kunnes viljan kosteuspitoisuus laskee tavoitetasoon. Viljan jyvistä irtoaa aina pölyä niiden hangatessa toisiaan vasten. Viljankuivaamoiden pölyisyyttä on normaalisti pyritty vähentämään poistamalla leijuvaa pölyä viljan liikkeen epäjatkuvuuskohdista. Pölyä kulkeutuu kuitenkin kuivaamon ulkopuolelle myös kuivaukseen käytetyn ilman mukana. Poistoilman pölypitoisuus ei tavallisesti ole korkea, mutta kuivaamiseen käytetyistä suurista ilmamääristä johtuen pölyä voi kertyä poistoilmakanavan ympäristöön huomattavia määriä. Tämän diplomityön tavoitteena onkin viljankuivurin poistoilman pölypitoisuuden vähentämiseen soveltuvan pölynhallintajärjestelmän kehittäminen. Selvityksessä tarkasteltiin ensinnäkin kuivurin poistoilman pölypitoisuuteen liittyvää kansallista ja kansainvälistä lainsäädäntöä sekä raja-arvoja. Lähdemateriaalin perusteella kartoitettiin pölypitoisuuden vähentämiseen soveltuvia menetelmiä sekä kilpailijoiden toteuttamia ratkaisuja. Myös muita pölynhallintajärjestelmän edellytyksiä selvitettiin. Teoreettisessa tarkastelussa teknistaloudellisesti parhaaksi osoittautunut pölynhallintaratkaisu jalostettiin prototyypiksi. Sen toimintakykyä testattiin erotustehokkuuden mittaamiseen soveltuvan koelaitteiston avulla. Testitulosten perusteella kyseinen pölynhallintajärjestelmä todettiin toimivaksi ja pienellä jatkokehittelyllä myös kaupalliseen käyttöön soveltuvaksi. Testitulosten hyödyntämismahdollisuuksien lisäksi diplomityössä esitetään myös muutamia jatkokehitysehdotuksia.

Analysis and Control of Excitation, Field Weakening and Stability in Direct Torque Controlled Electrically Excited Synchronous Motor Drives

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor’s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque reference. This method is however parameter sensitive and requires a safety margin between the theoretical torque maximum and the actual torque limit. The DTC modulation principle allows however a direct load angle adjustment without any current control. In this work a direct load angle control method has been developed. The method keeps the drive stabile and allows the maximal utilisation of the drive without a safety margin in the torque limitation.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

Adaptive control of Hydraulic Drive

Adaptive control systems are one of the most significant research directions of modern control theory. It is well known that every mechanical appliance’s behavior noticeably depends on environmental changes, functioning-mode parameter changes and changes in technical characteristics of internal functional devices. An adaptive controller involved in control process allows reducing an influence of such changes. In spite of this such type of control methods is applied seldom due to specifics of a controller designing. The work presented in this paper shows the design process of the adaptive controller built by Lyapunov’s function method for the Hydraulic Drive. The calculation needed and the modeling were conducting with MATLAB® software including Simulink® and Symbolic Math Toolbox™ etc. In the work there was applied the Jacobi matrix linearization of the object’s mathematical model and derivation of the suitable reference models based on Newton’s characteristic polynomial. The intelligent adaptive to nonlinearities algorithm for solving Lyapunov’s equation was developed. Developed algorithm works properly but considered plant is not met requirement of functioning with. The results showed confirmation that adaptive systems application significantly increases possibilities in use devices and might be used for correction a system’s behavior dynamics.

Teollisuuspuhaltimille tarkoitetun suunnittelujärjestelmän kehittäminen

Diplomityön tavoitteena oli kehittää Dust Control Systems Oy:n nykyistä suunnittelujärjestelmää yrityksen toiminnan laadun ja suunnittelun tehokkuuden parantamiseksi. Suunnittelun suurin pullonkaula on valmistusdokumenttien tuottaminen, joten keskeinen tehtävä oli dokumenttien laadun parantaminen ja tuottamisen nopeuttaminen. Lisäksi tärkeää oli selkeyttää nykyistä nimikkeiden hallintaa ja ylläpitoa. Kehitystyö keskittyi suurelta osin suunnittelujärjestelmän ohjelmistoympäristön päivittämiseen ja sen muokkaamiseen. Teoriaosuudessa käsiteltiin nykyaikaista suunnittelua ja sen kehittämismahdollisuuksia. Lisäksi tarkasteltiin suunnittelun automatisoinnin tuomia hyötyjä sekä erilaisia tuotannon tehostamismenetelmiä. Kehitysosiossa tutkittiin yrityksen nykyistä suunnittelujärjestelmää ja ohjelmistoympäristöä, tuotteiden asettamia vaatimuksia sekä järjestelmän puutteita. Näihin liittyi suuresti yhteistyö henkilöstön sekä ohjelmistotoimittajan kanssa. Tutkimuksen perusteella ryhdyttiin kehittämään uutta järjestelmäkokonaisuutta, johon liitettiin tarvittavia ohjelmistoja ja päivityksiä. Käyttöönottoa varten ohjelmistot konfiguroitiin yrityksen tarpeita vastaaviksi. Työn tuloksena saatiin kehittyneempi ja nykyaikaisempi suunnittelujärjestelmä ja ohjelmistoympäristö. Suunnittelijoiden työtaakkaa saadaan kevennettyä toistuvien työvaiheiden pidemmälle viedyllä automatisoinnilla. Uudistettu ohjelmistoympäristö luo osaltaan ehtoja ja sääntöjä, jotta virheitä syntyy yhä vähemmän. Lisäksi suunnittelun läpimenoaikaa saadaan lyhennettyä parannetulla dokumenttien tuottamisella.