Measurement of the air permeability profile on SC paper machine

Tämän diplomityön tarkoituksena oli asentaa ja kehittää UPM-Kymmene Rauman tehtaiden PK2:lle luotettava ja toimiva ilmanläpäisyprofiilin mittaus. Työn tarkoituksena oli myös kartoittaa tietoja ilmanläpäisyprofiiliin vaikuttavista seikoista sekä mahdollisuuksista säätää ilmanläpäisyprofiilia. Lisäksi työn tavoitteena oli löytää toimiva menetelmä verrata online mitattua ilmanläpäisyprofiilia laboratoriossa mitattuun ilmanläpäisyprofiiliin online mittauksen luotettavuuden näkökulmasta. Työn aikana selvitettiin myös ilmanläpäisyprofiilin mittauksen mahdollisuutta superkalanteroidusta SC paperista. Työn kirjallisessa osassa käsiteltiin paperin huokoisuutta ja ilmanläpäisyä, huokoisuustasoon ja huokoisuus profiiliin vaikuttavia tekijöitä, ilmanläpäisevyyden merkitystä SC paperin valmistukselle ja SC paperin painettavuudelle sekä ilmanläpäisevyyden laboratorio- sekä online mittausta. Kirjallisessa osassa käsiteltiin myös Honeywellin uutta Poros ilmanläpäisysensoria. Työn kokeellisessa osassa tutkittiin ilmanläpäisyprofiilimittauksen luotettavuutta CD ja MD suunnassa sekä laboratorio- ja online-mittausten välisiä eroavaisuuksia ennen PK2 uusintaa. PK2 uusinnan jälkeen kokeellisessa osassa keskityttiin luotettavuuden varmentamiseen CD ja MD suunnassa sekä kartoittamaan tekijöitä, jotka aiheuttivat pieniä tasoeroja mittausten välillä. Mittaukset todettiin luotettaviksi ja niiden pohjalta suoritettiin mitattujen online profiilien välisiä vertailuja. Ilmanläpäisyprofiililla todettiin olevan positiivinen korrelaatio neliömassaprofiilin ja kosteusprofiilin kanssa sekä negatiivinen korrelaatio tuhkaprofiilin kanssa. PK2 uusinnan yhteydessä tehtiin koeajoja, jotka liittyivät laadunoptimointiin viira- ja puristinosalla. Koeajoissa tutkittujen asioiden lisäksi tutkittiin muutettujen parametrien vaikutusta ilmanläpäisyprofiiliin. Höyrylaatikon vaikutusta ilmanläpäisyprofiiliin tutkittiin säätöjen virityksen yhteydessä.

Ultrasonic and Electrokinetic Remediation of Low Permeability Soil Contaminated with Persistent Organic Pollutants

Electrokinetics has emerged as a potential technique for in situ soil remediation and especially unique because of the ability to work in low permeability soil. In electrokinetic remediation, non-polar contaminants like most organic compounds are transported primarily by electroosmosis, thus the process is effective only if the contaminants are soluble in pore fluid. Therefore, enhancement is needed to improve mobility of these hydrophobic compounds, which tend to adsorb strongly to the soil. On the other hand, as a novel and rapidly growing science, the applications of ultrasound in environmental technology hold a promising future. Compared to conventional methods, ultrasonication can bring several benefits such as environmental friendliness (no toxic chemical are used or produced), low cost, and compact instrumentation. It also can be applied onsite. Ultrasonic energy applied into contaminated soils can increase desorption and mobilization of contaminants and porosity and permeability of soil through developing of cavitation. The research investigated the coupling effect of the combination of these two techniques, electrokinetics and ultrasonication, in persistent organic pollutant removal from contaminated low permeability clayey soil (with kaolin as a model medium). The preliminary study checked feasibility of ultrasonic treatment of kaolin highly contaminated by persistent organic pollutants (POPs). The laboratory experiments were conducted in various conditions (moisture, frequency, power, duration time, initial concentration) to examine the effects of these parameters on the treatment process. Experimental results showed that ultrasonication has a potential to remove POPs, although the removal efficiencies were not high with short duration time. The study also suggested intermittent ultrasonication over longer time as an effective means to increase the removal efficiencies. Then, experiments were conducted to compare the performances among electrokinetic process alone and electrokinetic processes combined with surfactant addition and mainly with ultrasonication, in designed cylinders (with filtercloth separating central part and electrolyte parts) and in open pans. Combined electrokinetic and ultrasonic treatment did prove positive coupling effect compared to each single process alone, though the level of enhancement is not very significant. The assistance of ultrasound in electrokinetic remediation can help reduce POPs from clayey soil by improving the mobility of hydrophobic organic compounds and degrading these contaminants through pyrolysis and oxidation. Ultrasonication also sustains higher current and increases electroosmotic flow. Initial contaminant concentration is an essential input parameter that can affect the removal effectiveness.

Quantum transport phenomena and shallow impurity states in CdSb

This work is dedicated to investigation of the energy spectrum of one of the most anisotropic narrow-gap semiconductors, CdSb. At the beginning of the present studies even the model of its energy band structure was not clear. Measurements of galvanomagnetic effects in wide temperature range (1.6 - 300 K) and in magnetic fields up to 30 T were chosen for clarifying of the energy spectrum in the intentionally undoped CdSb single crystals and doped with shallow impurities (In, Ag). Detection of the Shubnikov - de Haas oscillations allowed estimating the fundamental energy spectrum parameters. The shapes of the Fermi surfaces of electrons (sphere) and holes (ellipsoid), the number of the equivalent extremums for valence band (2) and their positions in the Brillouin zone were determined for the first time in this work. Also anisotropy coefficients, components of the tensor of effective masses of carriers, effective masses of density of states, nonparabolicity of the conduction and valence bands, g-factor and its anisotropy for n- and p-CdSb were estimated for the first time during these studies. All the results obtained are compared with the cyclotron resonance data and the corresponding theoretical calculations for p-CdSb. This is basic information for the analyses of the complex transport properties of CdSb and for working out the energy spectrum model of the shallow energy levels of defects and impurities in this semiconductor. It was found out existence of different mechanisms of hopping conductivity in the presence of metal - insulator transition induced by magnetic field in n- and p-CdSb. Quite unusual feature opened in CdSb is that different types of hopping conductivity may take place in the same crystal depending on temperature, magnetic field or even orientation of crystal in magnetic field. Transport properties of undoped p-CdSb samples show that the anisotropy of the resistivity in weak and strong magnetic fields is determined completely by the anisotropy of the effective mass of the holes. Temperature and magnetic field dependence of the Hall coefficient and magnetoresistance is attributed to presence of two groups of holes with different concentrations and mobilities. The analysis demonstrates that below Tcr ~ 20 K and down to ~ 6 - 7 K the low-mobile carriers are itinerant holes with energy E2 ≈ 6 meV. The high-mobile carriers, at all temperatures T < Tcr, are holes activated thermally from a deeper acceptor band to itinerant states of a shallower acceptor band with energy E1 ≈ 3 meV. Analysis of temperature dependences of mobilities confirms the existence of the heavy-hole band or a non-equivalent maximum and two equivalent maxima of the light-hole valence band. Galvanomagnetic effects in n-CdSb reveal the existence of two groups of carriers. These are the electrons of a single minimum in isotropic conduction band and the itinerant electrons of the narrow impurity band, having at low temperatures the energies above the bottom of the conduction band. It is found that above this impurity band exists second impurity band of only localized states and the energy of both impurity bands depend on temperature so that they sink into the band gap when temperature is increased. The bands are splitted by the spin, and in strong magnetic fields the energy difference between them decreases and redistribution of the electrons between the two impurity bands takes place. Mobility of the conduction band carriers demonstrates that scattering in n-CdSb at low temperatures is strongly anisotropic. This is because of domination from scattering on the neutral impurity centers and increasing of the contribution to mobility from scattering by acoustic phonons when temperature increases. Metallic conductivity in zero or weak magnetic field is changed to activated conductivity with increasing of magnetic field. This exhibits a metal-insulator transition (MIT) induced by the magnetic field due to shift of the Fermi level from the interval of extended states to that of the localized states of the electron spectrum near the edge of the conduction band. The Mott variablerange hopping conductivity is observed in the low- and high-field intervals on the insulating side of the MIT. The results yield information about the density of states, the localization radius of the resonant impurity band with completely localized states and about the donor band. In high magnetic fields this band is separated from the conduction band and lies below the resonant impurity bands.

Puristinhuopien pesutehokkuuden vaikutus puristinosan ajettavuuteen

Työn tarkoituksena oli kehittää jatkuvatoimiseen pesuun soveltuva emäksinen ja hapan huovanpesuaine sekä tutkia huovanpesun parametreja laboratoriossa ja paperikoneella. Kirjallisuusosassa tarkasteltiin paperikoneen puristinosaa, puristinhuopien ominaisuuksia, puristinhuovissa esiintyviä saostumia ja puristinhuopien kunnostusta sekä esiteltiin FeltPerm-vedenläpäisykykymittari. Kokeellisessa osassa analysoitiin käytetty huopa kvalitatiivisesti ja kvantitatiivisesti ja kun huopaa tukkivien yhdisteiden kemiallinen luonne oli selvitetty, kehitettiin käynninaikaiseen pesuun soveltuva emäksinen ja hapan huovanpesuaine. Huovanpesuaineiden kehitystyössä pesuaineiden tehokkuutta tutkittiin kolmella eri menetelmällä, joista kaksi perustui huovan massan muutoksen määrittämiseen pesussa ja yksi huovan vedenläpäisykyvyn mittaamiseen. Kehitetyillä pesuaineilla optimoitiin laboratoriossa happo- ja emäspesun pH sekä vaikutusaika. Lisäksi tutkittiin huovan turpoamista emäspesussa ja lämpötilan vaikutusta pesutulokseen. Puristinhuopien vedenläpäisykykyä tutkittiin FeltPerm-laitteella kahdella eri SC-paperikoneella, joista toisella oli käytössä käynninaikainen jaksottainen pesu ja toisella pelkät seisokkipesut. Koneella, jossa huovat pestiin käynninaikaisesti, määritettiin pesuparametreja ja optimoitiin emäsvaiheen aikainen pH. Kehitetyillä pesuaineilla suoritettiin koeajo tehtaalla.

Optimization of the procedure for removing iron deposits on ceramic filter media

In this thesis, cleaning of ceramic filter media was studied. Mechanisms of fouling and dissolution of iron compounds, as well as methods for cleaning ceramic membranes fouled by iron deposits were studied in the literature part. Cleaning agents and different methods were closer examined in the experimental part of the thesis. Pyrite is found in the geologic strata. It is oxidized to form ferrous ions Fe(II) and ferric ions Fe(III). Fe(III) is further oxidized in the hydrolysis to form ferric hydroxide. Hematite and goethite, for instance, are naturally occurring iron oxidesand hydroxides. In contact with filter media, they can cause severe fouling, which common cleaning techniques competent enough to remove. Mechanisms for the dissolution of iron oxides include the ligand-promoted pathway and the proton-promoted pathway. The dissolution can also be reductive or non-reductive. The most efficient mechanism is the ligand-promoted reductive mechanism that comprises two stages: the induction period and the autocatalytic dissolution.Reducing agents(such as hydroquinone and hydroxylamine hydrochloride), chelating agents (such as EDTA) and organic acids are used for the removal of iron compounds. Oxalic acid is the most effective known cleaning agent for iron deposits. Since formulations are often more effective than organic acids, reducing agents or chelating agents alone, the citrate¿bicarbonate¿dithionite system among others is well studied in the literature. The cleaning is also enhanced with ultrasound and backpulsing.In the experimental part, oxalic acid and nitric acid were studied alone andin combinations. Also citric acid and ascorbic acid among other chemicals were tested. Soaking experiments, experiments with ultrasound and experiments for alternative methods to apply the cleaning solution on the filter samples were carried out. Permeability and ISO Brightness measurements were performed to examine the influence of the cleaning methods on the samples. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis of the solutions was carried out to determine the dissolved metals.

Heran nanosuodatus: raaka-ainekoostumuksen ja prosessiolosuhteiden vaikutus kalvon likaantumiseen

Työssä tutkittiin kalvon likaantumiseen vaikuttavia tekijöitä juoksuteheran nanosuodatuksessa. Tutkimuksessa käytettiin Desal-5 DK kalvoa. Heran nanosuodatukset suoritettiin yhden spiraalimoduulin käsittävää pilot -mittakaavaista suodatuslaitteistoa käyttäen. Työssä selvitettiin suodatettavan heran iän, pastörointilämpötilan, pH:n, suodatuslämpötilan sekäheran sisältämän juustopölyn, lisätyn kalsiumkloridin määrän ja rasvan laadun vaikutusta permeaattivuohon. Jokaista tekijää testattiin kahta eri muuttujaa käyttäen. Työssä tutkittiin myös kahden samanlaisen kalvon välisiä läpäisevyyseroja. Heran pastörointilämpötila, pH ja suodatuslämpötila osoittautuivat kalvon likaantumisen kannalta tärkeimmiksi tekijöiksi heran nanosuodatuksessa. Permeaattivuo oli korkeampi suodatettaessa 74 ºC lämpötilassa pastöroitua heraa, kuin 78 ºC lämpötilassa pastöroitua. Hera suodattui paremmin silloin, kunsen pH oli säädetty 5,8:aan, kuin heran pH:n ollessa säädettynä 5,2:een. Suodatettaessa 18 ºC suodatuslämpötilaan temperoitua heraa havaittiin korkeampi permeaattivuo kuin 12 ºC lämpötilaan termostoitua heraa suodatettaessa. Heran sisältämä pölyn määrä, rasvan laatu ja heran ikä havaittiin tilastollisesti merkityksettömiksi tekijöiksi sekä heran suodattuvuuden, että kalvon puhdistuvuuden kannalta. Kalsiumkloridin lisääminen heraan ennen suodatusta vaikuttivain kalvon suodatuksen jälkeiseen peseytyvyyteen. Kalvo puhdistui paremmin, kun kalsiumkloridia ei oltu lisätty heraan ennen suodatusta. Desal-5 DK kalvojen läpäisevyyseroja tutkittiin suodattamalla glukoosia ja natriumkloridia sisältävää malliaineliuosta kummankin vertailtavan kalvon läpi. Kokeissa havaittiin, että toista nanosuodatuskalvoa käytettäessä mitatut vesivuot olivat jopa 100 % korkeampia kuin vertailukalvoa käytettäessä mitatut. Myös glukoosin kalvolle pidättymisessä havaittiin eroja kalvojen välillä. Syyksi suuriin läpäisevyyseroihin arveltiin riittämätöntä kalvojen esikäsittelyä ennen malliainekokeen suorittamista, joten ei pystytty arvioimaan, oliko kalvojen läpäisevyyksissävalmistusprosessista johtuvia eroja.

Korkeakappa-massan suotatuvuus

Työn tarkoituksena oli tutkia korkeakappa-massan suotautuvuutta sekä etsiä uusia analyysimenetelmiä korkeakappa-massan karakterisoimiseksi. Työssä pyrittiin määrittämään tekijöitä, jotka vaikuttavat korkeakappa-massan suotautumiseen. Työn kirjallisessa osassa tarkasteltiin aluksi yleisesti keiton teoriaa, minkä jälkeen käsiteltiin jauhatusta ja tarkemmin korkeakappa-massan hienovaraisempaa jauhatusta eli kuidutusta. Seuraavaksi käsiteltiin suodatusta ja sen teoriaa sekä suodatukseen vaikuttavia tekijöitä. Massan pesusta esitettiin perusteet ja teoriaa. Lopuksi tarkasteltiin massan karakterisointia eri lähestymistavoilla sekä kuitujen perusominaisuuksia. Kokeellisessa osassa verrattiin LTY:n koesuodatuslaitteistolla tehdyillä suodatuskokeilla korkeakappa-massaisen sellukakun suotautuvuutta eri paine-eroilla, suodoksen eri hienoainepitoisuuksilla sekä ennen ja jälkeen sellutehtaallatapahtuneen kuidutuksen. Savonlinnassa sijaitsevalla laitteistolla tehtiin syrjäytystestejä ennen ja jälkeen kuidutusta otetuilla sellumassoilla. Lisäksi ennenja jälkeen kuidutusta otettuja sellumassanäytteitä karakterisoitiin mm. kuituanalysaattorilla, huokoskoko- ja ominaispinta-ala-analyyseillä sekä SEM-kuvilla. Suodatuskokeissa hienoainepitoisuudella ei ollut merkitystä permeabiliteettiin mitattujen suodosvirtausten perusteella. Kuten Darcyn lain perusteella voitiin olettaa, kakun paine-eron kasvaessa permeabiliteetti kasvoi. Vaikutus ei ollut kuitenkaan lineaarinen paine-eroon verrattuna vaan kakun permeabiliteetti kasvoi enemmän tietyllä paine-erovälillä. Tämä paine-eroväli vaihteli hieman riippuen oliko sellumassa otettu ennen vai jälkeen kuidutusta. Lappeenrannassa tehdyissä suodatuskokeissa ei ennen ja jälkeen kuidutusta otetuilla näytteillä ollut selvää eroa permeabiliteeteissa, mutta Savonlinnan syrjäytystesteissä ero syrjäytymisnopeudessa oli selvä. Ennen ja jälkeen kuidutusta otettujen sellumassojen kuituanalysaattorituloksissa ja SEM-kuvissa ei havaittu eroa näytteiden välillä, mutta massojen huokoskoko muuttui kuidutuksen vaikutuksesta.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Modeling of non-isothermalvapor membrane separation with thermodynamic models and generalized mass transfer equations

A rigorous unit operation model is developed for vapor membrane separation. The new model is able to describe temperature, pressure, and concentration dependent permeation as wellreal fluid effects in vapor and gas separation with hydrocarbon selective rubbery polymeric membranes. The permeation through the membrane is described by a separate treatment of sorption and diffusion within the membrane. The chemical engineering thermodynamics is used to describe the equilibrium sorption of vapors and gases in rubbery membranes with equation of state models for polymeric systems. Also a new modification of the UNIFAC model is proposed for this purpose. Various thermodynamic models are extensively compared in order to verify the models' ability to predict and correlate experimental vapor-liquid equilibrium data. The penetrant transport through the selective layer of the membrane is described with the generalized Maxwell-Stefan equations, which are able to account for thebulk flux contribution as well as the diffusive coupling effect. A method is described to compute and correlate binary penetrant¿membrane diffusion coefficients from the experimental permeability coefficients at different temperatures and pressures. A fluid flow model for spiral-wound modules is derived from the conservation equation of mass, momentum, and energy. The conservation equations are presented in a discretized form by using the control volume approach. A combination of the permeation model and the fluid flow model yields the desired rigorous model for vapor membrane separation. The model is implemented into an inhouse process simulator and so vapor membrane separation may be evaluated as an integralpart of a process flowsheet.

Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.

A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Lämmönsiirron numeerinen laskenta profiloidulle kanavalle.

Työn tavoitteena oli tutkia aaltomaisen profiloinnin vaikutusta suorien jäähdytyskanavien lämmönsiirtoon ja painehäviöön. Erilaisia profiileja oli kymmenen kappaletta ja ne olivat 5mm leveitä ja 30cm pitkiä kukin. Ne laskettiin kolmeulotteisina tapauksina FINFLO-virtausratkaisijalla kolmella eri Reynoldsin luvulla, jotka vastasivat laminaarista, osittain turbulenttista ja lähes kokonaan turbulenttista virtausta. Lämmönsiirtoaine oli kuiva +30°C ilma ja profiloinnin toteutustapa oli toisiaan sivuavat ympyräkaaret kolmella erilaisella säteen arvolla ja kolmella erilaisella aallonpituuden arvolla. Lisäksi laskettiin saman levyisen tasokanavan arvot jokaisella Reynoldsin luvulla kaksiulotteisina tapauksina. Näitä profiloimattomia kanavia pidettiin referenssitapauksina. Tuloksena havaittiin että profiloimalla saadaan yksiselitteisesti suurempi lämpöteho ulos samasta tilavuudesta. Lämmönsiirtokerroin kasvaa profiloinnin avulla parhaimmillaan n. 20% käytetystä turbulenssimallista tai lämmönsiirtokertoimen määritelmästä riippumatta. Painehäviö kasvaa myös aina, mutta kitkakerroin voi hieman pienentyä. Profiilin varsinaisena hyvyyskriteerinä pidettiin lämmönsiirtokertoimen ja kitkakertoimen suhdetta h/f. Se osoittautui riippuvaksi Reynoldsin luvusta ja turbulenssimallista; ASM ja Chien k-έ -mallit ennustavat transitioetäisyyden eri tavalla. Laminaarisilla virtauksilla h/f :n vaihtelu oli vähäistä; suhde vaihteli vain ±5% eri profiilien kesken. ASM-mallilla havaittiin sekundääripyörteilyä, ehkä siksi että se mallintaa anisotrooppisen turbulenssin. Chien k-έ malli ennusti suuremman ja aikaisemmin alkavan turbulenttisuuden kuin ASM. Lisäksi havaittiin mm. että tietyillä profiileilla muodostuu kanavan kapeimpaan kohtaan selvä virtausnopeuden paikallinen minimi seinämän läheisyyden takia.

PulpExpert-massa-analysaattorin arkinmuodostus

Laboratoriossa tutkittiin rainaussakeuden ja neliömassan vaikutusta formaatioon ja muiden paperin ominaisuuksien hajontoihin sakeusalueella 0,036 %- 0,067 % ja neliömassa-alueella 65 g/m2- 125 g/m2. Havaittiin, että rainaussakeudella oli vaikutusta vain mäntysellusta valmistettujen arkkien formaatioon. Neliömassan noustessa kaikista tutkituista massoista valmistettujen arkkien formaatiot huononivat. Pulseeraus tai alipaine vedenpoiston aikana ei parantanut Turbulence Pulse Sheet Former-laitteella valmistettujen kuumahierrearkkien formaatiota. Kahdella koelaitteella tehtiin sakeusajo, toistokoe ja vuorottelukoe. Laite A mittasi tiettyihin sakeuksiin valmistettujen massojen sakeudet tarkasti. Laitteen B sakeusmittauksessa havaittiin säännöllinen poikkeama. Toistokokeen tuloksista tarkasteltiin mitattujen arvojen hajontoja, laitteiden massanerotuskykyä ja arkkien formaatiota. Laite A teki silmämääräisesti tasaisempia arkkeja, mutta niiden formaatio oli huonompi. Laitteella A saavutettiin pienemmät näytepisteiden sisäiset hajonnat repäisylujuusmittauksessa ja laitteella B vaaleuden mittauksessa. Laite A erotteli massat paremmin vaaleusmittauksessa ja laite B ilmanläpäisevyyden mittauksessa. Vuorottelukokeessa havaittiin, ettei massojen nopea vuorottelu kasvata olennaisesti mittaustuloksien hajontoja.

Kalvojen vertailu heran nanosuodatuksessa

Työssä verrattiin kaupallisia nanosuodatuskalvoja heran konsentroinnissa. Tutkitut kalvot olivat Desal-5 DK, NF45 ja Koch SR1. NF45-kalvosta tutkittiin kahta eri sukupolven kalvoa. Konsentrointiajoja tehtiin sekä laboratoriomittakaavan levysuotimella että pilot-mittakaavan spiraalimoduulilaitteella. Lisäksi tutkittiin juoksute- ja happoheran konsentrointien eroja. Erityistä huomiota kiinnitettiin permeaattivuon arvoihin konsentroinnissa ja kalvojen suolojen ja laktoosin pidätyskykyyn. NF45-kalvon uuden sukupolven malli osoittautui mittauksissa samankaltaiseksi suolojen ja laktoosin pidätyskyvyltään kuin Desal-5 DK. Koch SR1-kalvo, jonka suolojen ja laktoosin pidätyskyky on Desal-5 DK-kalvoa heikompi, puolestaan vastaa ominaisuuksiltaan NF45 vanhan sukupolven kalvoa. Vanhan sukupolven NF45-kalvon valmistus on loppunut keväällä 2000. Vaihdettaessa vanhan sukupolven NF45-kalvot uuden sukupolven kalvoihin on odotettavissa pienemmät permeaattivuot ja suuremmat suolojen ja laktoosin retentiot kuin aiemmin NF45-kalvolla. Juoksuteheran konsentroinnissa suurimmat permeaattivuot saatiin Koch SR1-kalvolla. Levysuotimella ja spiraalimoduulilla saadaan koostumukseltaan samanlainen juoksuteheratiiviste. Levysuotimella permeaattivuot ovat samalla konsentrointikertoimella suuremmat kuin spiraalimoduulilla. Tämä johtuu spiraalimoduuliin jäävistä kuolleista alueista, joissa ei ole virtausta. Uutta prosessia suunniteltaessa voidaan käyttää laboratoriomittakaavan levysuodinkokokeita, kun halutaan tietoa saatavan tuotteen koostumuksesta. Prosessin tuotantokapasiteetin arvioimiseen tarvitaan pilot-mittakaavan spiraalimoduulikokeita. Happoheratiiviste sisältää enemmän suoloja kuin samalla kalvolla valmistettu juoksuteheratiiviste. Tämä johtuu happoheran juoksuteheraa suuremmasta suolapitoisuudesta. Lisäksi happoheran konsentroinnin permeaattivuo on pienempi kuin juoksuteheran permeaattivuo, sillä happoheran alhainen pH, noin 4,5, vaikuttaa kalvon permeabiliteettiin heikentävästi.