Effect of Shielding Gases in Laser Welding of Aluminium Alloys

High reflectivity to laser light, alloying element evaporation during high power laser welding makes aluminium alloys highly susceptibility to weld defects such as porosity, cracking and undercutting. The dynamic behaviour of the keyhole, due to fluctuating plasma above the keyhole and the vaporization ofthe alloying elements with in the keyhole, is the key problem to be solved for the improvement of the weld quality and stabilization of the keyhole dynamics isperhaps the single most important development that can broaden the application of laser welding of aluminium alloys. In laser welding, the shielding gas is commonly used to stabilize the welding process, to improve the welded joint features and to protect the welded seam from oxidation. The chemicalcomposition of the shielding gas is a key factor in achieving the final qualityof the welded joints. Wide range of shielding gases varying from the pure gasesto complex mixtures based on helium, argon, nitrogen and carbon dioxide are commercially available. These gas mixtures should be considered in terms of their suitability during laser welding of aluminium alloys to produce quality welds. The main objective of the present work is to study the effect of the shielding gascomposition during laser welding of aluminium alloys. Aluminium alloy A15754 was welded using 3kW Nd-YAG laser (continuous wave mode). The alloy samples were butt welded with different shielding gases (pure and mixture of gases) so that high quality welds with high joint efficiencies could be produced. It was observed that the chemical composition of the gases influenced the final weld quality and properties. In general, the mixture gases, in correct proportions, enabled better utilisation of the properties of the mixing gases, stabilized the welding process and produced better weld quality compared to the pure shielding gases.

Weldability of high strength aluminium alloys

The need for reduced intrinsic weight of structures and vehicles in the transportation industry has made aluminium research of interest. Aluminium has properties that are favourable for structural engineering, including good strength-to-weight ratio, corrosion resistance and machinability. It can be easily recycled saving energy used in smelting as compared to steel. Its alloys can have ultimate tensile strength of up to 750 MPa, which is comparable to steel. Aluminium alloys are generally weldable, however welding of high strength alloys like the 7xxx series pose considerable challenges. This paper presents research on the weldability of high strength aluminium alloys, principally the 7xxx series. The weldability with various weld processes including MIG, TIG, and FSW, is discussed in addition to consideration of joint types, weld defects and recommendations for minimizing or preventing weld defects. Experimental research was carried out on 7025-T6 and AW-7020 alloys. Samples were welded, and weld cross sections utilized in weld metallurgy studies. Mechanical tests were carried out including hardness tests and tensile tests. In addition, testing was done for the presence of Al2O3 on exposed aluminium alloy. It was observed that at constant weld heat input using a pulsed MIG system, the welding speed had little or no effect on the weld hardness. However, the grain size increased as the filler wire feed rate, welding current and welding speed increased. High heat input resulted in lower hardness of the weld profile. Weld preheating was detrimental to AW- 7020 welds; however, artificial aging was beneficial. Acceptable welds were attained with pulsed MIG without the removal of the Al2O3 layer prior to welding. The Al2O3 oxide layer was found to have different compositions in different aluminium alloys. These findings contribute useful additional information to the knowledge base of aluminium welding. The application of the findings of this study in welding will help reduce weld cost and improve high strength aluminium structure productivity by removing the need for pre-weld cleaning. Better understanding of aluminium weld metallurgy equips weld engineers with information for better aluminium weld design.

Nd:YAG Laser Welding of 5083 Aluminium Alloy using Filler Wire

High reflectivity and high thermal conductivity, high vapour pressure of alloyingelements as well as low liquid surface tension and low ionisation potential, make laser welding of aluminium and its alloys a demanding task.Problems that occur during welding are mainly process instabilities of the keyhole and the melt pool, increased plasma formation above the melt pool and loss of alloying elements. These problems lead to unwanted metallurgical defects like hot cracks and porosity in the weld bead andother problems concerning the shape and appearance of the weld bead. In order to minimise the defects and improve the weld quality, the process and beam parameters need to be carefully adjusted along with a consideration concerning the use of filler wire for the welding process. In this work the welding of 3,0 mm thick grade 5083 aluminium alloy plates using a 3,0 kW Nd:YAG laser with grade 5183 filler wire addition is investigated. The plates were welded as butt joints with air gap sizes 0,5 mm, 0,7mm and 1,0 mm. The analysis of the weld beads obtained from the weldedsamples showed that the least imperfections were produced with 0,7 mm air gaps at moderate welding speeds. The analysis also covered the calculation of the melting efficiency and the study of the shape of the weld bead. The melting efficiency was on average around 20 % for the melting process of the welded plates. The weld beads showed the characteristic V-shape of a laser weld and retained this shape during the whole series of experiments.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Aluminium fouling and its impact on activated carbon based dioxin and furan removal in a wet scrubber at a co-incineration plant

Dioxins and furans, PCDD/Fs, are highly toxic substances formed in post combustion zones in furnaces. PCDD/F emissions are regulated by a waste incineration directive which relates also to co-incineration plants. Several observations of dioxin and furan enhancements in wet scrub- bers have been reported previously. This is thought to be due to the so-called "memory effect" which occurs when dioxins and furans absorb into plastic material in scrubbers and desorb when ambient circumstances alter significantly. At the co-incineration plant involved, dioxins and furans are controlled with a wet scrubber, the tower packing of which is made of plastic in which activated carbon particles are dispersed. This should avoid the memory effect and act as a dioxin and furan sink since dioxins and furans are absorbed irreversibly into the packing ma- terial. In this case, the tower packing in the scrubber is covered with a white layer that has been found to be mainly aluminium. The aim of this thesis was to determine the aluminium balance and the dioxin and furan behaviour in the scrubber and, thus, the impacts that the foul- ing has on dioxin and furan removal. The source of aluminium, reasons for fouling and further actions to minimize its impacts on dioxin and furan removal were also to be discovered. Measurements in various media around the scrubber and in fuels were made and a profile analysis of PCDD/F and mass balance calculations were carried out. PCDD/F content de- creased in the scrubber. The reduced PCDD/F was not discharged into scrubbing water. The removal mechanism seems to work in spite of the fouling, at least with low PCDD/F loads. Most of the PCDD/F in excess water originates from the Kymijoki River which is used as feeding water in the scrubber. Fouling turned out to consist mainly of aluminium hydroxides. Sludge combusted in the furnace was found to be a significant source of aluminium. Ways to minimize the fouling would be adjustment of pH to a proper lever, installation of a mechanical filter to catch the loose material from the scrubbing water and affecting the aluminium content of the sludge.

Commodity Price Driven Risk Management from Viewpoint of High Grade Steel Alloys

The study of price risk management concerning high grade steel alloys and their components was conducted. This study was focused in metal commodities, of which nickel, chrome and molybdenum were in a central role. Also possible hedging instruments and strategies for referred metals were studied. In the literature part main themes are price formation of Ni, Cr and Mo, the functioning of metal exchanges and main hedging instruments for metal commodities. This section also covers how micro and macro variables may affect metal prices from the viewpoint of short as well as longer time period. The experimental part consists of three sections. In the first part, multiple regression model with seven explanatory variables was constructed to describe price behavior of nickel. Results were compared after this with information created with comparable simple regression model. Additionally, long time mean price reversion of nickel was studied. In the second part, theoretical price of CF8M alloy was studied by using nickel, ferro-chrome and ferro-molybdenum as explanatory variables. In the last section, cross hedging possibilities for illiquid FeCr -metal was studied with five LME futures. Also this section covers new information concerning possible forthcoming molybdenum future contracts as well. The results of this study confirm, that linear regression models which are based on the assumption of market rationality, are not able to reliably describe price development of metals at issue. Models fulfilling assumptions for linear regression may though include useful information of statistical significant variables which have effect on metal prices. According to the experimental part, short futures were found to incorporate the most accurate information concerning the price movements in the future. However, not even 3M futures were able to predict turning point in the market before the faced slump. Cross hedging seemed to be very doubtful risk management strategy for illiquid metals, because correlations coefficients were found to be very sensitive for the chosen time span.

Kevyiden rakennemateriaalien soveltamismahdollisuudet metsäkoneissa

Asiakkaiden ympäristötietoisuus, metsäkoneille asetettavat korkeat vaatimukset ja kiristyvä kilpailu pakottavat metsäkoneiden valmistajat etsimään vaihtoehtoisia valmistusmateriaaleja, joita käyttämällä metsäkoneet kevenevät ja sitä kautta niiden ympäristökuormitukset ja käyttökustannukset alenevat ja kapasiteetti kasvaa. Metsäkoneiden rakenteiden keventämisessä alumiini on yksi varteenotettava vaihtoehto teräksen korvaajaksi, sillä alumiinin ominaisuus/paino -suhde on terästä parempi. Alumiinin käyttöä hitsatuissa rakenteissa ovat rajoittaneet sen korkea hinta ja melko huono väsymiskestävyys. Diplomityön tavoitteena on ollut selvittää mahdollisuuksia korvata metsäkoneiden rakenteista löytyviä teräksestä valmistettuja osia alumiinista valmistetuilla osilla. Diplomityön teoriaosassa on käsitelty rakenteiden keventämistä, metsäkoneille asetettavia vaatimuksia, alumiinien materiaaliominaisuuksia, alumiinirakenteiden valmistuksessa käytettäviä menetelmiä sekä alumiinirakenteiden suunnittelua. Lisäksi teoriaosassa on käsitelty komposiittien materiaaliominaisuuksia ja komposiittirakenteiden suunnittelua. Diplomityön kokeellisessa osassa on vertailtu nykyisiä rakennemateriaaleja ja alumiineja metsäkoneen eri osien rakennemateriaaleina osien vaatimusprofiileihin ja materiaalien ominaisuusprofiileihin perustuen. Vaatimusprofiilien perusteella on laadittu ominaisuusprofiilit alumiineille ja teräksille. Sovittamalla vaatimus- ja ominaisuusprofiilit yhteen arvoanalyysin avulla, metsäkoneista on etsitty mahdollisia kohteita, joissa nykyinen rakennemateriaali voitaisiin korvata alumiinilla. Tältä pohjalta metsäkoneista löytyi rakenteita, joissa alumiinin käyttö rakennemateriaalina teräksen sijaan olisi mahdollista. Diplomityö toimii hyvänä pohjana tutkittaessa mahdollisuuksia metsäkoneiden rakenteiden keventämiseksi.

Moottoripyörän rungon muuntelun valvontakriteerit muutoskatsastuksessa

Muutoskatsastusta koskeva lainsäädäntö aiheuttaa tulkintavaikeuksia ja rajoitteita moottoripyöräharrastajille ja alan toimijoille. Nykyinen asetus edellyttää tarvittaessa asiantuntijaselvitystä rakennemuutoksen lujuudesta ja hitsaustyöstä. Moottoripyörän geometria on laissa rajattu akselivälin ja emäputken kulman osalta. Moottoripyörien runkoja valmistetaan hitsaamalla seostamattomista teräksistä ja lämpökäsiteltävistä alumiini- ja terässeoksista. Runkojen muuntelu suoritetaan myös yleisesti hitsaamalla. Turvallisuuden kannalta tärkeiltä hitsausliitoksilta vaaditaan hyvää laatua, joka saavutetaan oikeilla hitsausparametreilla ja -suorituksella. Vaatimukset seostamattomalle teräkselle voidaan täyttää pätevöityneen hitsaajan toimesta. Lämpökäsiteltävät seokset vaativat lisäksi jälkilämpökäsittelyn, mikä edelleen vaikeuttaa runkojen hitsausta. Hitsien laadun merkitystä moottoripyörän rungossa tutkittiin soveltamalla rajoitetun vahingon periaatetta. Vauriotapauksena mallinnettiin satunnaisen rungon hitsausliitoksen murtuminen. Eri kuormitustilanteissa elementtimenetelmää hyödyntäen todettiin chopper-tyyppisten moottoripyörien runkojen olevan osittain vauriosietoisia ja havaittiin kriittiset hitsausliitokset emä- ja vaakaputken alueilla. Moottoripyörien runkojen kriittisiä hitsausliitoksia tarkasteltiin väsymisen kannalta. Soveltamalla tehollista lovijännitystä, vertailtiin emäputken hitsausliitosten väsymiskestävyyttä oletetulla kuormituksella. Tulosten perusteella muunneltu moottoripyörän runko voi olla alkuperäisrunkoa kestävämpi tai heikompi. Moottoripyörän akseliväli tai emäputken kulma eivät määrää kestävyyttä, vaan rakenteen yksityiskohtainen suunnittelu. Kriittisten liitosten väsymiskestävyyksissä havaittiin merkittäviä eroja eri mallien välillä.

Alumiinipainevalujen purseen- ja jäysteenpoiston kehitysmahdollisuudet

Valupurseiden ja jäysteiden poistaminen on osa alumiinipainevalujen tuotantoprosessia. Työssä on tutkittu käytössä olevien ja uusien menetelmien mahdollisuuksia taloudellisempaan tuotantoon. Purseiden ja jäysteiden poistamiseen käytettävien menetelmien lisäksi tutkimuskohteita ja ideoita on haettu muista metallien työstömenetelmistä. Valupurseiden ja jäysteiden määritelmiä, muodostumista ja luokittelua on esitelty laajasti. Menetelmien tutkimus on painottunut valupurseiden poistamiseen ja valun jälkeistä leikkaamista on tutkittu erityisesti sisäpuolisten muotojen työstämiseen käytettyjen pistintyökalujen kautta. Muotin ulostyöntötapin purseen poistaminen on ollut tärkeä asia menetelmien tutkimuksissa. Valupurseiden, leikkaus- ja koneistusjäysteiden poistamiseksi lastuavista työstömenetelmistä tutkittuja ovat koneistaminen koneistuskeskuksella, aventaminen, hiertopuhallus, suihkuhiertäminen, vesisuihkuleikkaus, ultraäänityöstö, harjaus, painehiertäminen, hiominen kohdistetuilla ja kohdistamattomilla menetelmillä. Myös terminen jäysteenpoistomenetelmä (TEM), kemiallinen työstö (ECM) ja laserleikkaus on otettu esiin tutkimuksessa. Työn tuloksena on näkemys tutkittujen menetelmien jatkokehitystarpeesta ja mahdollisuudesta soveltaa niitä sarjatuotantoon.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

First principles modeling of metallic alloys and alloy surfaces

By alloying metals with other materials, one can modify the metal’s characteristics or compose an alloy which has certain desired characteristics that no pure metal has. The field is vast and complex, and phenomena that govern the behaviour of alloys are numerous. Theories cannot penetrate such complexity, and the scope of experiments is also limited. This is why the relatively new field of ab initio computational methods has much to give to this field. With these methods, one can extend the understanding given by theories, predict how some systems might behave, and be able to obtain information that is not there to see in physical experiments. This thesis pursues to contribute to the collective knowledge of this field in the light of two cases. The first part examines the oxidation of Ag/Cu, namely, the adsorption dynamics and oxygen induced segregation of the surface. Our results demonstrate that the presence of Ag on the Cu(100) surface layer strongly inhibits dissociative adsorption. Our results also confirmed that surface reconstruction does happen, as experiments predicted. Our studies indicate that 0.25 ML of oxygen is enough for Ag to diffuse towards the bulk, under the copper oxide layer. The other part elucidates the complex interplay of various energy and entropy contributions to the phase stability of paramagnetic duplex steel alloys. We were able to produce a phase stability map from first principles, and it agrees with experiments rather well. Our results also show that entropy contributions play a very important role on defining the phase stability. This is, to the author’s knowledge, the first ab initio study upon this subject.

Hitsatun alumiinikappaleen anodisointi

Tämän työn tarkoituksena oli selvittää, mitä on alumiinin pintakäsittelymenetelmä anodisointi ja kuinka se tapahtuu. Esille otettu esimerkkitapaus liittyy hitsatun alumiinin anodisointiin ja siinä ilmenneisiin ongelmiin.

Modern Metallic Materials for Arctic Environment

This thesis is part of the Arctic Materials Technologies Development –project, which aims to research and develop manufacturing techniques, especially welding, for Arctic areas. The main target of this paper is to clarify what kind of European metallic materials are used, or can be used, in Arctic. These materials include mainly carbon steels but also stainless steels and aluminium and its alloys. Standardized materials, their properties and also some recent developments are being introduced. Based on this thesis it can be said that carbon steels (shipbuilding and pipeline steels) have been developed based on needs of industry and steels exist, which can be used in Arctic areas. Still, these steels cannot be fully benefited, because rules and standards are under development. Also understanding of fracture behavior of new ultra high strength steels is not yet good enough, which means that research methods (destructive and non-destructive methods) need to be developed too. The most of new nickel-free austenitic and austenitic-ferritic stainless steels can be used in cold environment. Ferritic and martensitic stainless steels are being developed for better weldability and these steels are mainly developed in nuclear industry. Aluminium alloys are well suitable for subzero environment and these days high strength aluminium alloys are available also as thick sheets. Nanotechnology makes it possible to manufacture steels, stainless steels and aluminium alloys with even higher strength. Joining techniques needs to be developed and examined properly to achieve economical and safe way to join these modern alloys.

Alumiinin oksidikerroksen merkitys hitsauksessa

Tämä kandidaatintyö on kirjallisuuden pohjalta laadittu yhteenveto alumiinin oksidikerroksen vaikutuksesta hitsauksessa. Työssä käsitellään alumiinia alkuaineena, alumiinin oksidikerroksen muodostumista ja rakennetta, seosaineiden vaikutusta oksidikerrokseen, alumiinin hitsattavuutta teräkseen vertaillen, alumiiniseosten hitsattavuutta, oksidikerroksen merkitystä hitsauksessa, alumiinin yleisiä hitsausvirheitä, oksidikerroksen poistotapoja sekä alumiinin eri hitsausmenetelmiä. Hitsausmenetelmistä käsitellään pääasiassa alumiinin MIG-, TIG- ja plasmahitsausta.

First-principles study on electronic and structural properties of Cu(In/Ga)Se alloys for solar cells

Thin-film photovoltaic solar cells based on the Cu(In1−xGax)Se2 (CIGS) alloys have attracted more and more attention due to their large optical absorption coefficient, long term stability, low cost, and high efficiency. Modern theoretical studies of this material with first-principles calculations can provide accurate description of the electronic structure and yield results in close agreement with experimental values, but takes a large amount of calculation time. In this work, we use first-principles calculations based on the computationally affordable meta- generalized gradient approximation of the density-functional theory to investigate electronic and structural properties of the CIGS alloys. We report on the simulation of the lattice parameters and band gaps, as a function of chemical composition. The obtained results were found to be in a good agreement with the available experimental data.