Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Drivers and barriers of mobile travel and tourism service adoption : a study of individual perceptions and business model development in a travel and tourism context

The Travel and Tourism field is undergoing changes due to the rapid development of information technology and digital services. Online travel has profoundly changed the way travel and tourism organizations interact with their customers. Mobile technology such as mobile services for pocket devices (e.g. mobile phones) has the potential to take this development even further. Nevertheless, many issues have been highlighted since the early days of mobile services development (e.g. the lack of relevance, ease of use of many services). However, the wide adoption of smartphones and the mobile Internet in many countries as well as the formation of so-called ecosystems between vendors of mobile technology indicate that many of these issues have been overcome. Also when looking at the numbers of downloaded applications related to travel in application stores like Google Play, it seems obvious that mobile travel and tourism services are adopted and used by many individuals. However, as business is expected to start booming in the mobile era, many issues have a tendency to be overlooked. Travelers are generally on the go and thus services that work effectively in mobile settings (e.g. during a trip) are essential. Hence, the individuals’ perceived drivers and barriers to use mobile travel and tourism services in on-site or during trip settings seem particularly valuable to understand; thus this is one primary aim of the thesis. We are, however, also interested in understanding different types of mobile travel service users. Individuals may indeed be very different in their propensity to adopt and use technology based innovations (services). Research is also switching more from investigating issues of mobile service development to understanding individuals’ usage patterns of mobile services. But designing new mobile services may be a complex matter from a service provider perspective. Hence, our secondary aim is to provide insights into drivers and barriers of mobile travel and tourism service development from a holistic business model perspective. To accomplish the research objectives seven different studies have been conducted over a time period from 2002 – 2013. The studies are founded on and contribute to theories within diffusion of innovations, technology acceptance, value creation, user experience and business model development. Several different research methods are utilized: surveys, field and laboratory experiments and action research. The findings suggest that a successful mobile travel and tourism service is a service which supports one or several mobile motives (needs) of individuals such as spontaneous needs, time-critical arrangements, efficiency ambitions, mobility related needs (location features) and entertainment needs. The service could be customized to support travelers’ style of traveling (e.g. organized travel or independent travel) and should be easy to use, especially easy to take into use (access, install and learn) during a trip, without causing security concerns and/or financial risks for the user. In fact, the findings suggest that the most prominent barrier to the use of mobile travel and tourism services during a trip is an individual’s perceived financial cost (entry costs and usage costs). It should, however, be noted that regulations are put in place in the EU regarding data roaming prices between European countries and national telecom operators are starting to see ‘international data subscriptions’ as a sales advantage (e.g. Finnish Sonera provides a data subscription in the Baltic and Nordic region at the same price as in Finland), which will enhance the adoption of mobile travel and tourism services also in international contexts. In order to speed up the adoption rate travel service providers could consider e.g. more local initiatives of free Wi-Fi networks, development of services that can be used, at least to some extent, in an offline mode (do not require costly network access during a trip) and cooperation with telecom operators (e.g. lower usage costs for travelers who use specific mobile services or travel with specific vendors). Furthermore, based on a developed framework for user experience of mobile trip arrangements, the results show that a well-designed mobile site and/or native application, which preferably supports integration with other mobile services, is a must for true mobile presence. In fact, travel service providers who want to build a relationship with their customers need to consider a downloadable native application, but in order to be found through the mobile channel and make contact with potential new customers, a mobile website should be available. Moreover, we have made a first attempt with cluster analysis to identify user categories of mobile services in a travel and tourism context. The following four categories were identified: info-seekers, checkers, bookers and all-rounders. For example “all-rounders”, represented primarily by individuals who use their pocket device for almost any of the investigated mobile travel services, constituted primarily of 23 to 50 year old males with high travel frequency and great online experience. The results also indicate that travel service providers will increasingly become multi-channel providers. To manage multiple online channels, closely integrated and hybrid online platforms for different devices, supporting all steps in a traveler process should be considered. It could be useful for travel service providers to focus more on developing browser-based mobile services (HTML5-solutions) than native applications that work only with specific operating systems and for specific devices. Based on an action research study and utilizing a holistic business model framework called STOF we found that HTML5 as an emerging platform, at least for now, has some limitations regarding the development of the user experience and monetizing the application. In fact, a native application store (e.g. Google Play) may be a key mediator in the adoption of mobile travel and tourism services both from a traveler and a service provider perspective. Moreover, it must be remembered that many device and mobile operating system developers want service providers to specifically create services for their platforms and see native applications as a strategic advantage to sell more devices of a certain kind. The mobile telecom industry has moved into a battle of ecosystems where device makers, developers of operating systems and service developers are to some extent forced to choose their development platforms.

Alpha- and gamma-melanocyte stimulating hormones in obesity. A study of the key central areas of metabolic regulation

The melanocortin system is an important regulator of feeding, energy metabolism,and cardiovascular function and it consists of the pro-opiomelanocortin (POMC) derived melanocyte stimulating hormones (α-, β- and γ-MSH) and their endogenous melanocortin receptors, MC1R to MC5R. In the hypothalamus, α-MSH reduces food intake, and increases energy expenditure and sympathetic tone by binding to MC4R. Mutations affecting the MC4R gene lead to obesity in mammals. On the other hand, the metabolic effects of MC3R stimulation using agonists such as the endogenously expressed γ-MSH have been less extensively explored. The main objective of this study was to investigate the long-term effects of increased melanocortin tone in key areas of metabolic regulation in the central nervous system (CNS) in order to investigate the sitespecific roles of both α-MSH and γ-MSH. The aim was to stereotaxically induce local overexpression of single melanocortin peptides using lentiviral vectors expressing α-MSH (LVi-α-MSH-EGFP) and γ-MSH (LVi-γ-MSH-EGFP). The lentiviral vectors were shown to produce a long-term overexpression and biologically active peptides in cell-based assays. The LVi-α-MSHEGFP was targeted to the arcuate nucleus in the hypothalamus of diet induced obese mice where it reduced weight gain and adiposity independently of food intake. When the nucleus tractus solitarus in the brainstem was targeted, the LVi-α-MSH-EGFP treatment was shown to cause a small decrease in adiposity, which did not impact weight development. However, the α-MSH treatment increased heart rate, which was attenuated by adrenergic receptor blockade indicative of increased sympathetic activity. The LVi-γ-MSH-EGFP was targeted to the hypothalamus where it decreased fat mass in mice eating the standard diet, but the effect was abated if animals consumed a high-fat Western type diet. When the diet induced obese mice were subjected again to the standard diet, the LVi-γ-MSH-EGFP treated animals displayed increased weight loss and reduced adiposity. These results indicate that the long-term central anti-obesity effects of α-MSH are independent of food intake. In addition, overexpression of α-MSH in the brain stem efficiently blocked the development of adiposity, but increased sympathetic tone. The evidence presented in this thesis also indicates that selective MC3R agonists such as γ-MSH could be potential therapeutics in combination with low fat diets.

Belt conveyor energy efficiency analysis and energy model development

An energy model of a belt conveyor was designed. Operation of a belt conveyor was researched. Operational indexes were calculated. Energy optimization process and recommendations were presented.

3D Mesh Simplification. A survey of algorithms and CAD model simplification tests

Simplification of highly detailed CAD models is an important step when CAD models are visualized or by other means utilized in augmented reality applications. Without simplification, CAD models may cause severe processing and storage is- sues especially in mobile devices. In addition, simplified models may have other advantages like better visual clarity or improved reliability when used for visual pose tracking. The geometry of CAD models is invariably presented in form of a 3D mesh. In this paper, we survey mesh simplification algorithms in general and focus especially to algorithms that can be used to simplify CAD models. We test some commonly known algorithms with real world CAD data and characterize some new CAD related simplification algorithms that have not been surveyed in previous mesh simplification reviews.

Active Magnetic Bearing System Identification Methods and Rotor Model Updating

Active magnetic bearing is a type of bearing which uses magnetic field to levitate the rotor. These bearings require continuous control of the currents in electromagnets and data from position of the rotor and the measured current from electromagnets. Because of this different identification methods can be implemented with no additional hardware. In this thesis the focus was to implement and test identification methods for active magnetic bearing system and to update the rotor model. Magnetic center calibration is a method used to locate the magnetic center of the rotor. Rotor model identification is an identification method used to identify the rotor model. Rotor model update is a method used to update the rotor model based on identification data. These methods were implemented and tested with a real machine where rotor was levitated with active magnetic bearings and the functionality of the methods was ensured. Methods were developed with further extension in mind and also with the possibility to apply them for different machines with ease.

Selecting, testing and modifying a model for identifying potential key customers

Tämä työ tehtiin globaaliin elektroniikka-alan yritykseen. Diplomityö liittyy haasteeseen, jonka lisääntynyt globalisaatio ja kiristyvä kilpailu ovat luoneet: case yrityksen on selvitettävä kuinka se voi saavuttaa kasvutavoitteet myös tulevaisuudessa hankkimalla uusia asiakkaita ja olemalla yhä enenevissä määrin maailmanlaajuisesti läsnä. Tutkimuksen tavoite oli löytää sopiva malli potentiaalisten avainasiakkaiden identifiointiin ja valintaan, sekä testata ja modifioida valittua mallia case yrityksen tarpeiden mukaisesti. Erityisesti raakadatan kerääminen, asiakkaiden houkuttelevuuskriteerit ja kohdemarkkinarako olivat asioita, jotka tarvitsivat tutkimuksessa huomiota. Kirjallisuuskatsauksessa keskityttiin yritysmarkkinoihin, eri asiakassuhteenhallinnan lähestymistapoihin ja avainasiakkaiden määrittämiseen. CRM:n, KAM:n ja Customer Insight-ajattelun perusteet esiteltiin yhdessä eri avainasiakkaiden identifiointimallien kanssa. Valittua Chevertonin mallia testattiin ja muokattiin työn empiirisessä osassa. Tutkimuksen empiirinen kontribuutio on modifioitu malli potentiaalisten avainasiakkaiden identifiointiin. Se auttaa päätöksentekijöitä etenemään systemaattisesti ja organisoidusti askel askeleelta kohti potentiaalisten asiakkaiden listaa tietyltä markkina-alueelta. Työ tarjoaa työkalun tähän prosessiin sekä luo pohjaa tulevaisuuden tutkimukselle ja toimenpiteille.

Mobile Subscription Acquisition and Retention Costs - An Actvity-Based Model

The objective of this master’s thesis was to develop a model for mobile subscription acquisition cost, SAC, and mobile subscription retention cost, SRC, by applying activity-based cost accounting principles. The thesis was conducted as a case study for a telecommunication company operating on the Finnish telecommunication market. In addition to activity-based cost accounting there were other theories studied and applied in order to establish a theory framework for this thesis. The concepts of acquisition and retention were explored in a broader context with the concepts of customer satisfaction, loyalty and profitability and eventually customer relationship management to understand the background and meaning of the theme of this thesis. The utilization of SAC and SRC information is discussed through the theories of decision making and activity-based management. Also, the present state and future needs of SAC and SRC information usage at the case company as well as the functions of the company were examined by interviewing some members of the company personnel. With the help of these theories and methods it was aimed at finding out both the theory-based and practical factors which affect the structure of the model. During the thesis study it was confirmed that the existing SAC and SRC model of the case company should be used as the basis in developing the activity-based model. As a result the indirect costs of the old model were transformed into activities and the direct costs were continued to be allocated directly to acquisition of new subscriptions and retention of old subscriptions. The refined model will enable managing the subscription acquisition, retention and the related costs better through the activity information. During the interviews it was found out that the SAC and SRC information is also used in performance measurement and operational and strategic planning. SAC and SRC are not fully absorbed costs and it was concluded that the model serves best as a source of indicative cost information. This thesis does not include calculating costs. Instead, the refined model together with both the theory-based and interview findings concerning the utilization of the information produced by the model will serve as a framework for the possible future development aiming at completing the model.

Induction Motor Drive Energy Efficiency - Simulation and Analysis

A coupled system simulator, based on analytical circuit equations and a finite element method (FEM) model of the motor has been developed and it is used to analyse a frequency-converterfed industrial squirrel-cage induction motor. Two control systems that emulate the behaviour of commercial direct-torque-controlled (DTC) and vector-controlled industrial frequency converters have been studied, implemented in the simulation software and verified by extensive laboratory tests. Numerous factors that affect the operation of a variable speed drive (VSD) and its energy efficiency have been investigated, and their significance in the simulation of the VSD results has been studied. The dependency of the frequency converter, induction motor and system losses on the switching frequency is investigated by simulations and measurements at different speeds for both the vector control and the DTC. Intensive laboratory measurements have been carried out to verify the simulation results.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Performance of active portfolio management and the effect of stock market trend

Purpose of the study is to evaluate performance of active portfolio management and the effect of stock market trend on the performance. Theory of efficient markets states that market prices reflect all available information and that all investors share a common view of future price developments. This view gives little room for the success of active management, but the theory has been disputed – at least the level of efficiency. Behavioral finance has developed theories that identify irrational behavior patterns of investors. For example, investment decisions are not made independent of past market developments. These findings give reason to believe that also the performance of active portfolio management may depend on market developments. Performance of 16 Finnish equity funds is evaluated during the period of 2005 to 2011. In addition two sub periods are constructed, a bull market period and a bear market period. The sub periods are created by joining together the two bull market phases and the two bear market phases of the whole period. This allows for the comparison of the two different market states. Performance of the funds is measured with risk-adjusted performance by Modigliani and Modigliani (1997), abnormal return over the CAPM by Jensen (1968), and market timing by Henriksson and Merton (1981). The results suggested that in average the funds are not able to outperform the market portfolio. However, the underperformance was found to be lower than the management fees in average which suggests that portfolio managers are able to do successful investment decisions to some extent. The study revealed substantial dependence on the market trend for all of the measures. The risk-adjusted performance measure suggested that in bear markets active portfolio managers in average are able to beat the market portfolio but not in bull markets. Jensen´s alpha and the market timing model also showed striking differences between the two market states. The results of these two measures were, however, somewhat problematic and reliable conclusions about the performance could not be drawn.

Regulation of epidermal tight junctions by calcium ATPases and p38

The epidermis is the upper layer of the skin and keratinocytes are its most abundant cells. Tight junctions are cell junctions located in the granular layer of the epidermis. They maintain the polarity of the cells and regulate the movement of water-soluble molecules. Epidermal tight junctions may lose their integrity when there are defects in intercellular calcium regulation. Hailey-Hailey and Darier´s disease are dominantly inherited, blistering skin diseases. Hailey-Hailey disease is caused by mutations in the ATP2C1 gene encoding a calcium/manganese ATPase SPCA1 of the Golgi apparatus. Darier´s disease is caused by mutations in the ATP2A2 gene encoding a calcium ATPase SERCA2 of the endoplasmic reticulum. p38 regulates the differentiation of keratinocytes. The overall regulation of epidermal tight junctions is not well understood. The present study examined the regulation of tight junctions in the human epidermis with a focus on calcium ATPases and p38. Skin from Hailey-Hailey and Darier´s disease patients was studied by using immunofluorescence labeling which targeted intercellular junction proteins. Transepidermal water loss was also measured. ATP2C1 gene expression was silenced in cultured keratinocytes, by siRNA, which modeled Hailey-Hailey disease. Expression of intercellular junction proteins was studied at the mRNA and protein levels. Squamous cell carcinoma and normal human keratinocytes were used as a model for impaired and normal keratinocyte differentiation, and the role of p38 isoforms alpha and delta in the regulation of intercellular junction proteins was studied. Both p38 isoforms were silenced by adenovirus cell transduction, chemical inhibitors or siRNA and keratinocyte differentiation was assessed. The results of this thesis revealed that: i.) intercellular junction proteins are expressed normally in acantholytic skin areas of patients with Hailey-Hailey or Darier´s disease but the localization of ZO-1 expanded to the stratum spinosum; ii.) tight junction proteins, claudin-1 and -4, are regulated by ATP2C1 in non-differentiating keratinocytes; and iii.) p38 delta regulates the expression of tight junction protein ZO-1 in proliferating keratinocytes and in squamous cell carcinoma derived cells. ZO-1 silencing, however, did not affect the expression of other tight junction proteins, suggesting that they are differently regulated. This thesis introduces new mechanisms involved in the regulation of tight junctions revealing new interactions. It provides novel evidence linking intracellular calcium regulation and tight junctions.

Mathematical modeling and optimal control of malaria

Malaria continues to infect millions and kill hundreds of thousands of people worldwide each year, despite over a century of research and attempts to control and eliminate this infectious disease. Challenges such as the development and spread of drug resistant malaria parasites, insecticide resistance to mosquitoes, climate change, the presence of individuals with subpatent malaria infections which normally are asymptomatic and behavioral plasticity in the mosquito hinder the prospects of malaria control and elimination. In this thesis, mathematical models of malaria transmission and control that address the role of drug resistance, immunity, iron supplementation and anemia, immigration and visitation, and the presence of asymptomatic carriers in malaria transmission are developed. A within-host mathematical model of severe Plasmodium falciparum malaria is also developed. First, a deterministic mathematical model for transmission of antimalarial drug resistance parasites with superinfection is developed and analyzed. The possibility of increase in the risk of superinfection due to iron supplementation and fortification in malaria endemic areas is discussed. The model results calls upon stakeholders to weigh the pros and cons of iron supplementation to individuals living in malaria endemic regions. Second, a deterministic model of transmission of drug resistant malaria parasites, including the inflow of infective immigrants, is presented and analyzed. The optimal control theory is applied to this model to study the impact of various malaria and vector control strategies, such as screening of immigrants, treatment of drug-sensitive infections, treatment of drug-resistant infections, and the use of insecticide-treated bed nets and indoor spraying of mosquitoes. The results of the model emphasize the importance of using a combination of all four controls tools for effective malaria intervention. Next, a two-age-class mathematical model for malaria transmission with asymptomatic carriers is developed and analyzed. In development of this model, four possible control measures are analyzed: the use of long-lasting treated mosquito nets, indoor residual spraying, screening and treatment of symptomatic, and screening and treatment of asymptomatic individuals. The numerical results show that a disease-free equilibrium can be attained if all four control measures are used. A common pitfall for most epidemiological models is the absence of real data; model-based conclusions have to be drawn based on uncertain parameter values. In this thesis, an approach to study the robustness of optimal control solutions under such parameter uncertainty is presented. Numerical analysis of the optimal control problem in the presence of parameter uncertainty demonstrate the robustness of the optimal control approach that: when a comprehensive control strategy is used the main conclusions of the optimal control remain unchanged, even if inevitable variability remains in the control profiles. The results provide a promising framework for the design of cost-effective strategies for disease control with multiple interventions, even under considerable uncertainty of model parameters. Finally, a separate work modeling the within-host Plasmodium falciparum infection in humans is presented. The developed model allows re-infection of already-infected red blood cells. The model hypothesizes that in severe malaria due to parasite quest for survival and rapid multiplication, the Plasmodium falciparum can be absorbed in the already-infected red blood cells which accelerates the rupture rate and consequently cause anemia. Analysis of the model and parameter identifiability using Markov chain Monte Carlo methods is presented.

Modelling the Knowledge Interface between Sales and Production Functions of a Company. Case: New Service Development Process.

Yrityksen sisäisten rajapintojen tunteminen mahdollistaa tiedonvaihdon hallinnan läpi organisaation. Idean muokkaaminen kannattavaksi innovaatioksi edellyttää organisaation eri osien läpi kulkevaa saumatonta prosessiketjua sekä tietovirtaa. Tutkielman tavoitteena oli mallintaa organisaation kahden toiminnallisesti erilaisen osan välinen tiedon vaihto. Tiedon vaihto kuvattiin rajapintana, tietoliittymänä. Kolmiulotteinen organisaatiomalli muodosti tutkimuksen pääteorian. Se kytkettiin yrityksen tuotanto- ja myyntiosiin, kuten myös BestServ-projektin kehittämään uuteen palvelujen kehittämisen prosessiin. Uutta palvelujen kehittämisen prosessia laajennettiin ISO/IEC 15288 standardin kuvaamalla prosessimallilla. Yritysarkkitehtuurikehikoita käytettiin mallintamisen perustana. Tietoliittymä nimenä kuvastaa näkemystä siitä, että tieto [tietämys] on olemukseltaan yksilöiden tai ryhmien välistä. Mallinnusmenetelmät eivät kuitenkaan vielä mahdollista tietoon [tietämykseen] liittyvien kaikkien ominaisuuksien mallintamista. Tietoliittymän malli koostuu kolmesta osasta, joista kaksi esitetään graafisessa muodossa ja yksi taulukkona. Mallia voidaan käyttää itsenäisesti tai osana yritysarkkitehtuuria. Teollisessa palveluliiketoiminnassa sekä tietoliittymän mallinnusmenetelmä että sillä luotu malli voivat auttaa konepajateollisuuden yritystä ymmärtämään yrityksen kehittämistarpeet ja -kohteet, kun se haluaa palvelujen tuottamisella suuremman roolin asiakasyrityksen liiketoiminnassa. Tietoliittymän mallia voidaan käyttää apuna organisaation tietovarannon ja tietämyksen mallintamisessa sekä hallinnassa ja näin pyrkiä yhdistämään ne yrityksen strategiaa palvelevaksi kokonaisuudeksi. Tietoliittymän mallinnus tarjoaa tietojohtamisen kauppatieteelliselle tutkimukselle menetelmällisyyden tutkia innovaatioiden hallintaa sekä organisaation uudistumiskykyä. Kumpikin tutkimusalue tarvitsevat tarkempaa tietoa ja mahdollisuuksia hallita tietovirtoja, tiedon vaihtoa sekä organisaation tietovarannon käyttöä.