Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

A support system for evaluating a suitable joining method in the production of sheet metal goods

This report illustrates a comparative study of various joining methods involved in sheet metal production. In this report it shows the selection of joining methods, which includes comparing the advantages and disadvantages of a method over the other ones and choosing the best method for joining. On the basis of various joining process from references, a table is generated containing set of criterion that helps in evaluation of various sheet metal joining processes and in selecting the most suitable process for a particular product. Three products are selected and a comprehensive study of the joining methods is analyzed with the help of various parameters. The table thus is the main part of the analysis process of this study and can be advanced with the beneficial results. It helps in a better and easy understanding and comparing the various methods, which provides the foundation of this study and analysis. The suitability of the joining method for various types of cases of different sheet metal products can be tested with the help of this table. The sections of the created table display the requirements of manufacturing. The important factor has been considered and given focus in the table, as how the usage of these parameters is important in percentages according to particular or individual case. The analysis of the methods can be extended or altered by changing the parameters according to the constraint. The use of this table is demonstrated by pertaining the cases from sheet metal production.

Laser Cutting of Austenitic Stainless Steel with a High Quality Laser Beam

The thin disk and fiber lasers are new solid-state laser technologies that offer a combinationof high beam quality and a wavelength that is easily absorbed by metal surfacesand are expected to challenge the CO2 and Nd:YAG lasers in cutting of metals ofthick sections (thickness greater than 2mm). This thesis studied the potential of the disk and fiber lasers for cutting applications and the benefits of their better beam quality. The literature review covered the principles of the disk laser, high power fiber laser, CO2 laser and Nd:YAG laser as well as the principle of laser cutting. The cutting experiments were made with thedisk, fiber and CO2 lasers using nitrogen as an assist gas. The test material was austenitic stainless steel of sheet thickness 1.3mm, 2.3mm, 4.3mm and 6.2mm for the disk and fiber laser cutting experiments and sheet thickness of 1.3mm, 1.85mm, 4.4mm and 6.4mm for the CO2 laser cutting experiments. The experiments focused on the maximum cutting speeds with appropriate cut quality. Kerf width, cutedge perpendicularity and surface roughness were the cut characteristics used to analyze the cut quality. Attempts were made to draw conclusions on the influence of high beam quality on the cutting speed and cut quality. The cutting speeds were enormous for the disk and fiber laser cutting experiments with the 1.3mm and 2.3mm sheet thickness and the cut quality was good. The disk and fiber laser cutting speeds were lower at 4.3mm and 6.2mm sheet thickness but there was still a considerable percentage increase in cutting speeds compared to the CO2 laser cutting speeds at similar sheet thickness. However, the cut quality for 6.2mm thickness was not very good for the disk and fiber laser cutting experiments but could probably be improved by proper selection of cutting parameters.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Multispectral image compression using the wavelet transform

Multispectral images contain information from several spectral wavelengths and currently multispectral images are widely used in remote sensing and they are becoming more common in the field of computer vision and in industrial applications. Typically, one multispectral image in remote sensing may occupy hundreds of megabytes of disk space and several this kind of images may be received from a single measurement. This study considers the compression of multispectral images. The lossy compression is based on the wavelet transform and we compare the suitability of different waveletfilters for the compression. A method for selecting a wavelet filter for the compression and reconstruction of multispectral images is developed. The performance of the multidimensional wavelet transform based compression is compared to other compression methods like PCA, ICA, SPIHT, and DCT/JPEG. The quality of the compression and reconstruction is measured by quantitative measures like signal-to-noise ratio. In addition, we have developed a qualitative measure, which combines the information from the spatial and spectral dimensions of a multispectral image and which also accounts for the visual quality of the bands from the multispectral images.

Fibre-reinforced composites as root canal posts

Fibre-reinforced composite (FRC) root canal posts are suggested to have biomechanical benefits over traditional metallic posts, but they lack good adhesion to resin composites. The aim of this series of studies was to evaluate the adhesion of individually formed fibre-reinforced composite material to composite resin and dentin, as well as some mechanical properties. Flexural properties were evaluated and compared between individually formed FRC post material and different prefabricated posts. The depth of polymerization of the individually formed FRC post material was evaluated with IR spectrophotometry and microhardness measurements, and compared to that of resin without fibres. Bonding properties of the individually formed FRC post to resin cements and dentin were tested using Pull-out- and Push-out-force tests, evaluated with scanning electron microscopy, and compared to those of prefabricated FRC and metal posts. Load-bearing capacity and microstrain were evaluated and failure mode assessment was made on incisors restored with individually formed FRC posts of different structures and prefabricated posts. The results of these studies show that the individually polymerized and formed FRC post material had higher flexural properties compared to the commercial prefabricated FRC posts. The individually polymerized FRC material showed almost the same degree of conversion after light polymerization as monomer resin without fibres. Moreover, it was found that the individually formed FRC post material with a semiinterpenetrating polymer network (IPN) polymer matrix bonded better to composite resin luting cement, than did the prefabricated posts with a cross-linked polymer matrix. Furthermore, it was found that, contrary to the other posts, there were no adhesive failures between the individually formed FRC posts and composite resin luting cement. This suggests better interfacial adhesion of cements to these posts. Although no differences in load-bearing capacity or microstrain could be seen, the incisors restored with individually formed FRC posts with a hollow structure showed more favourable failures compared to other prefabricated posts. These studies suggest that it is possible to use individually formed FRC material with semi-IPN polymer matrix as root canal post material. They also indicate that there are benefits especially regarding the bonding properties to composite resin and dentin with this material compared to prefabricated FRC post material with a cross-linked matrix. Furthermore, clinically more repairable failures were found with this material compared to those of prefabricated posts.

Oliotietokannan muuttaminen relaatiotietokannaksi

Diplomityön tavoitteena oli parantaa oliotietokantaan perustuvan mökkivarausjärjestelmän pitkiä vasteaikoja ja epävakaata toimintaa sekä luoda tietokantaperusta uusille toiminnoille. Ratkaisua etsittiin korvaamalla oliotietokanta relaatiotietokannalla. Diplomityö on osa koko varausjärjestelmän uusintaa. Työn teoreettinen osuus käsittelee sekä olio- että relaatiotietokannan rakennetta ja oliomallin muuttamista relaatiomalliksi. Käytännön osassa esitellään relaatiotietokannan luominen vaiheittain ja kerrotaan tietojen siirron periaatteesta. Relaatiotietokannan havaittiin olevan vakaampi ja tehokkaampi vasteajoiltaan. Samoin sen vaatima levytilan ja muistin määrä oli pienempi kuin oliotietokannalla. Lisäksi siihen todettiin uusien järjestelmien liittämisen olevan yksinkertaisempaa.

Erikoispaperin käyristymisen pienentäminen mittapysyvyyttä parantamalla

Diplomityössä on tutkittu Tervakoski Oy:n PK8:lla valmistettavan irrokepaperin mittapy-syvyysongelmaa. Tämä ilmenee asiakkaan jatkojalostusprosesseissa esim. silikonointi- ja liimausvaiheissa paperin huonona ajettavuutena. Työ pohjautuu PK8:lla suoritettavien tehdasmittakaavaisten koeajojen prosessiolosuhteiden ja mittapysyvyyttä kuvaavien analyysien tulosten tarkasteluun. Työn kirjallisuusosassa kerrotaan silikonointi- ja laminointiprosessin vaatimuksista irrokepaperille. Mittapysyvyyden teoreettista taustaa lähestytään puukuidun sorptio-ominaisuuksien tarkastelulla. Osassa perehdytään mm. paperin mittapysyvyyteen ja käyristymiseen vaikuttaviin eri tekijöihin. Osio sisältää myös katsauksen paperin mittapysyvyyden ja käyristymisen eri mittausmenetelmistä. Työn kokeellisessa osassa tarkastellaan PK8:n prosessiolosuhteiden vaikutuksia mittapysy- vyyden tasoon. Kokeellinen osa sisältää neljä tehdasmittakaavaista koeajosarjaa ja 23 eri koepistettä, joiden tarkoituksena on löytää PK8:lle mittapysyvyyden kannalta parhaimmat mahdolliset olosuhteet muiden laatuarvojen kärsimättä. Koesarjojen muuttujina on käytetty kuivatusviirojen kireyttä, konesuuntaista vetojännitystä sekä suihkusuhteen ja jauhatusasteen muutoksia. Lisäksi paperin käyristymiseen pyrittiin vaikuttamaan PK8:lla toispuoleisella kuivatuksella ja erilliskostutuskoneen toispuoleisella kostutusvesimäärällä. Koesarjojen prosessiolosuhteiden ja analyysitulosten perusteella PK8:lla muutettiin ajotapamallia jo työn kuluessa. Kokeellisen osan loputtua PK8:n tuotantolinjalle määriteltiin uusi ajotapamalli. PK8:n tuotantolinjalla valmistettavan glassiinin poikkisuuntainen kuivatuskutistuma aleni eräässä koesarjassa prosessiolosuhteiden muutosten myötä noin 13 %. Mittapysy-vyyttä kuvaavat kosteuslaajentuma, märkämuodonmuutos ja käyristyminen paranivat keskimäärin 11 %. Uuden ajotapamallin myötä PK8:n valmistaman irrokepaperin laatutaso on noussut, jolloin on jo nyt havaittu, että glassiinin ajettavuus on selkeästi parantunut asiakkaan jatkojalostusprosesseissa.

VAP-1 in Leukocyte Trafficking

The extravasation of leukocytes from the blood stream into the tissues is a prerequisite for adequate immune surveillance and immune reaction. The leukocyte movement from the bloodstream into the tissues is mediated by molecular bonds. The bonds are formed between adhesion molecules on endothelial cells and their counterparts expressed on leukocytes. Vascular adhesion protein-1 (VAP-1) is an endothelial adhesion molecule mediating leukocyte interactions with endothelium. It is also an enzyme having semicarbazide sensitive amine oxidase (SSAO) activity. The SSAOactivity catalyses deamination of primary amines into corresponding aldehyde and during the enzymatic reaction hydrogen peroxide and ammonia are produced. The aim of this study was to investigate the relationship between the adhesive and enzymatic activities of VAP-1. The role of VAP-1 in leukocyte traffic was studied in vivo under normal and pathological conditions in VAP-1 deficient mice. The results from in vitro flow-based assays indicated that VAP-1 uses both SSAOactivity and its adhesive epitope to bind leukocytes, and both are perquisites for VAP-1 mediated adhesion. Furthermore, in vivo results demonstrated that leukocyte trafficking was impaired in vivo by deleting VAP-1 or inhibiting SSAO-activity. There was impairment in lymphocyte recirculation as well as leukocyte accumulation into the inflamed area. Moreover, the VAP-1 deficient mice did not show generalized defects in antimicrobial responses, whereas significant reduction in tumor progression and neovascularization was observed. These results indicate that VAP-1 could be used as a target in anti-adhesive therapies either by blocking its adhesive epitope with antibodies or by inhibiting its SSAO-activity using inhibitors. Moreover, targeting of VAP-1 may provide a new way of inhibiting neovascularization in tumors.

Paperin puhtauden parantaminen lajittelun ja muiden prosessiteknisten keinojen avulla

Tämä työ suoritettiin UPM- Kymmene Oyj:n Tervasaaren tehtaan PK 5:llä. PK 5 valmistaa tarrantaustapaperia. Tämän työn tarkoituksena oli löytää eri keinoja paperin puhtauden parantamiseksi. Puhtaamman paperin valmistaminen parantaa paperikoneen kilpailukykyä kilpailijoihinsa nähden sekä vähentää asiakasvalituskustannuksia. Työn kirjallinen osa koostuu kolmesta suuremmasta kokonaisuudesta, joiden tarkoituksena on luoda teoriapohjaa kokeellisen osan suoritusta varten. Kirjallisuusosan pääpaino on kohdistettu PK 5:llä esiintyviin saostumanaiheuttajiin, kuten uuteaineisiin, ASA- liimaan ja mikrobeihin. Tarkemmassa tarkastelussa on kirjallisuusosassa myös painelajittelu ja pyörrepuhdistus. Kokeellisessa osassa suoritettiin PK 5:n prosessissa syntyvien epäpuhtauksien karakterisointi. Suurimmat saostuman aiheuttajat analyysien perusteella olivat puuperäiset uuteaineet ja ASA- liima. Epäorgaanisista aineista päällystyskomponenttina toimiva kaoliini ja sellun mukana tuleva pihkatalkki esiintyi useimpien saostumien komponentteina. Selvityksessä havaittiin, että prosessille vieraita aineita ei löydetty muista, kuin kalanteroidusta paperista analysoiduista tummista täplistä. Tummista täplistä analysoitu styreenin alkuperä voi selittyä mm. prosessiin päässeellä kumilla tai muovilla. PK 5:n prosessissa selvityksen mukaan silikonipohjainen vaahdonestoaine aiheuttaa erittäin suuria tummia saostumia, joten sen pääsy prosessiin tulee estää sellutehtaalla tarkoin. Epäpuhtauksien määrä on suurin PK 5:n prosessissa hylkylinjassa ja lyhyessä kierrossa. Hylyn painelajittelu poistaa hyvin roskia syöttömassasta. Hylyn lajittelun toisen portaan lajittimen rejektin roskapitoisuus on suhteellisen suuri. Rejektin ohjaaminen ulos prosessista vähentää roskaisuuden rikastumista prosessiin. Sakeamassalajittelun sijoittaminen PK 5:n konekyypin jälkeen vähentää roskien päätymistä paperiin. Hylyn painelajittelun ja PP- laitoksen rejektin ohjaaminen sakeamassalajittelun toiseen portaaseen vähentäisi priimakuitutappiota ja roskien määrää käytetyissä massoissa. Seisokin aikaisen putkilinjojen pesujen lopputulos parani huomattavasti BA- pesuaineen käyttöönoton jälkeen. Kyseisen pesuaine soveltuu liuottamaan putkistosta mm. PK 5:llä esiintyvät uuteaine- ja ASA- saostumat. BSA- sellun pH- säädön lopettamisella oli suuri vähentävä vaikutus tummien täplien esiintymistiheyteen. pH- säädössä BSA- tornin pohjalaimennukseen annosteltu lipeä edesauttoi tummien saostumien syntymistä saippuoiden uuteaineita.

Genetic Basis and Diagnostics of Extended-Spectrum Beta-Lactamases among Enterobacteriaceae in Finland

Since the introduction of antibiotic agents, the amount and prevalence of Beta-lactam resistant enterobacteria has become an increasing problem. Many enterobacteria are opportunistic pathogens that easily acquire resistance mechanisms and genes, which make the situation menacing. These bacteria have acquired resistance and can hydrolyse extended spectrum cephalosporins and penicillins by producing enzymes called extended-spectrum Beta-lactamases (ESBLs). ESBL-producing bacteria are most commonly found in the gastro-intestinal tract of colonised patients. These resistant strains can be found in both health-care associated and community-acquired isolates. The detection and treatment of infections caused by bacteria producing ESBLs are problematic. This study investigated the genetic basis of extended-spectrum Beta-lactamases in Enterobacteriaceae, especially in Escherichia coli and Klebsiella pneumoniae isolates. A total of 994 Finnish Enterobacteriaceae strains, collected at 26 hospital laboratories, during 2000 and 2007 were analysed. For the genetic basis studies, PCR, sequencing and pyrosequencing methods were optimised. In addition, international standard methods, the agar dilution and disk diffusion methods were performed for the resistance studies, and the susceptibility of these strains was tested for antimicrobial agents that are used for treating patients. The genetic analysis showed that bla_CTX-M was the most prevalent gene among the E. coli isolates, while blaS_HV-12 was the most common Beta-lactamase gene in K. pneumoniae. The susceptibility testing results showed that about 60% of the strains were multidrug resistant. The prevalence of ESBL-producing isolates in Finland has been increasing since 2000. However, the situation in Finland is still much better than in many other European countries.

Lämpötilamuutosten vaikutukset metallien liimaliitoksiin

Diplomityön tavoitteena oli tutkia lämpötilan ja sen muutosten vaikutusta kahden metallin tai metallin ja magneetin väliseen liimaliitokseen. Tutkimuksen päätavoitteena oli tutkia magneettien liimaukseen käytetyn akryyliliiman lujuutta lämpösyklitysten jälkeen ja eri käyttölämpötilojen seurauksena. Teoriaosassa on käsitelty erilaisia liimauksen toteutukseen ja liimaliitoksen lujuuteen vaikuttavia tekijöitä. Erilaiset metallien liimaukseen soveltuvat liimatyypit ja niiden tarttumiseen liittyvät tekijät, kuten esikäsittelyt on myös käyty läpi teoriaosassa. Myös liiman- ja liimatyypin valintaa koskevia periaatteita ja tekniikoita on käsitelty. Käytännön osassa on esitelty koejärjestelyt sekä tutkittavat materiaalit ja niille suoritetut esikäsittelyt. Käytännön kokeissa suoritettavissa liimaliitoksissa käytettiin akryyli- ja silikoniliimoja, joille suoritettiin erilaisia vetokokeita. Akryyliliimalla liimatuille liitoksille suoritettiin myös lämpösyklityksiä, joita vertailtiin käsittelemättömiin liitoksiin. Magneettien ja metallien välisten liitosten lujuuden lisäksi liimalta saavutettavia lujuuksia arvioitiin rakenneterästen välisen liimaliitoksen sisältävillä vetosauvoilla. Suoritettujen kokeiden perusteella havaittiin lämpötilan vaikuttavan radikaalisesti liimaliitosten lujuuteen. Magneettien liimaliitoksilla saavutettiin käytännön sovellukseen riittävän suuria leikkauslujuuden arvoja vain huoneenlämpötilassa vedettäessä. Lämpösyklitysten todettiin myös heikentävän liitosta selvästi. Silikoniliiman lujuus oli alle sovelluskohteessa vaikuttavien voimien optimaalisissakin olosuhteissa. Metallien välisten liimaliitosten lujuuden todettiin heikentyvän nopeasti kasvatettaessa vetokokeissa käytettyä lämpötilaa. Liitoksen heikkenemistä havaittiin myös lämpötilaa laskettaessa.

Time-Resolved Photoluminescence in Antimonide and Dilute Nitride Quantum Well Structures

This Master's thesis is devoted to semiconductor samples study using time-resolved photoluminescence. This method allows investigating recombination in semiconductor samples in order to develop quality of optoelectronic device. An additional goal was the method accommodation for low-energy-gap materials. The first chapter gives a brief intercourse into the basis of semiconductor physics. The key features of the investigated structures are noted. The usage area of the results covers saturable semiconductor absorber mirrors, disk lasers and vertical-external-cavity surface-emittinglasers. The experiment set-up is described in the second chapter. It is based on up-conversion procedure using a nonlinear crystal and involving the photoluminescent emission and the gate pulses. The limitation of the method was estimated. The first series of studied samples were grown at various temperatures and they suffered rapid thermal annealing. Further, a latticematched and metamorphically grown samples were compared. Time-resolved photoluminescence method was adapted for wavelengths up to 1.5 µm. The results allowed to specify the optimal substrate temperature for MBE process. It was found that the lattice-matched sample and the metamorphically grown sample had similar characteristics.