Phosphorus content of ditch sediments as indicator of critical source areas

Selostus : Kilpailukykyinen menetelmä pistemäisten fosforikuormitusalueiden paikantamiseen

Pasvik Water Quality Report Environmental Monitoring Programme in the Norwegian, Finnish and Russian Border Area

The Pasvik monitoring programme was created in 2006 as a result of the trilateral cooperation, and with the intention of following changes in the environment under variable pollution levels. Water quality is one of the basic elements of the Programme when assessing the effects of the emissions from the Pechenganikel mining and metallurgical industry (Kola GMK). The Metallurgic Production Renovation Programme was implemented by OJSC Kola GMK to reduce emissions of sulphur and heavy metal concentrated dust. However, the expectations for the reduction in emissions from the smelter in the settlement Nikel were not realized. Nevertheless, Kola GMK has found that the modernization programme’s measures do not provide the planned reductions of sulfur dioxide emissions. In this report, temporal trends in water chemistry during 2000–2009 are examined on the basis of the data gathered from Lake Inari, River Pasvik and directly connected lakes, as well as from 26 small lakes in three areas: Pechenganikel (Russia), Jarfjord (Norway) and Vätsäri (Finland). The lower parts of the Pasvik watercourse are impacted by both atmospheric pollution and direct wastewater discharge from the Pechenganikel smelter and the settlement of Nikel. The upper section of the watercourse, and the small lakes and streams which are not directly linked to the Pasvik watercourse, only receive atmospheric pollution. The data obtained confirms the ongoing pollution of the river and water system. Copper (Cu), nickel (Ni) and sulphates are the main pollution components. The highest levels were observed close to the smelters. The most polluted water source of the basin is the River Kolosjoki, as it directly receives the sewage discharge from the smelters and the stream connecting the Lakes Salmijarvi and Kuetsjarvi. The concentrations of metals and sulphates in the River Pasvik are higher downstream from the Kuetsjarvi Lake. There has been no fall in the concentrations of pollutants in Pasvik watercourse over the last 10 years. Ongoing recovery from acidification has been evident in the small lakes of the Jarfjord and Vätsäri areas during the 2000s. The buffering capacity of these lakes has improved and the pH has increased. The reason for this recovery is that sulphate deposition has decreased, which is also evident in the water quality. However, concentrations of some metals, especially Ni and Cu, have risen during the 2000s. Ni concentrations have increased in all three areas, and Cu concentrations in the Pechenganickel and Jarfjord areas, which are located closer to the smelters. Emission levels of Ni and Cu did not fall during 2000s. In fact, the emission levels of Ni compounds even increased compared to the 1990s.

Long-term nutrient load management and lake restoration: Case of Säkylän Pyhäjärvi (SW Finland)

Eutrophication caused by anthropogenic nutrient pollution has become one of the most severe threats to water bodies. Nutrients enter water bodies from atmospheric precipitation, industrial and domestic wastewaters and surface runoff from agricultural and forest areas. As point pollution has been significantly reduced in developed countries in recent decades, agricultural non-point sources have been increasingly identified as the largest source of nutrient loading in water bodies. In this study, Lake Säkylän Pyhäjärvi and its catchment are studied as an example of a long-term, voluntary-based, co-operative model of lake and catchment management. Lake Pyhäjärvi is located in the centre of an intensive agricultural area in southwestern Finland. More than 20 professional fishermen operate in the lake area, and the lake is used as a drinking water source and for various recreational activities. Lake Pyhäjärvi is a good example of a large and shallow lake that suffers from eutrophication and is subject to measures to improve this undesired state under changing conditions. Climate change is one of the most important challenges faced by Lake Pyhäjärvi and other water bodies. The results show that climatic variation affects the amounts of runoff and nutrient loading and their timing during the year. The findings from the study area concerning warm winters and their influences on nutrient loading are in accordance with the IPCC scenarios of future climate change. In addition to nutrient reduction measures, the restoration of food chains (biomanipulation) is a key method in water quality management. The food-web structure in Lake Pyhäjärvi has, however, become disturbed due to mild winters, short ice cover and low fish catch. Ice cover that enables winter seining is extremely important to the water quality and ecosystem of Lake Pyhäjärvi, as the vendace stock is one of the key factors affecting the food web and the state of the lake. New methods for the reduction of nutrient loading and the treatment of runoff waters from agriculture, such as sand filters, were tested in field conditions. The results confirm that the filter technique is an applicable method for nutrient reduction, but further development is needed. The ability of sand filters to absorb nutrients can be improved with nutrient binding compounds, such as lime. Long-term hydrological, chemical and biological research and monitoring data on Lake Pyhäjärvi and its catchment provide a basis for water protection measures and improve our understanding of the complicated physical, chemical and biological interactions between the terrestrial and aquatic realms. In addition to measurements carried out in field conditions, Lake Pyhäjärvi and its catchment were studied using various modelling methods. In the calibration and validation of models, long-term and wide-ranging time series data proved to be valuable. Collaboration between researchers, modellers and local water managers further improves the reliability and usefulness of models. Lake Pyhäjärvi and its catchment can also be regarded as a good research laboratory from the point of view of the Baltic Sea. The main problem in both of them is eutrophication caused by excess nutrients, and nutrient loading has to be reduced – especially from agriculture. Mitigation measures are also similar in both cases.

Hulevesikuormitus ja sen vähentäminen rakennetulla alueella

Työssä tarkasteltiin hulevesien ravinnekuormituksen muodostumista ja kuormituksen vähentämismahdollisuuksia rakennetussa ympäristössä esimerkkialueena Sunisenlahden valuma-alue. Työn tavoitteena oli löytää ns. hotspot- alueet ja esittää valuma-alueelle osa-alueittain käsittelymenetelmä, joka soveltuu kyseisen alueen hulevesien käsittelyyn, huomioi alueen maankäytön, maastoprofiilin, maanomistuksesta ja maaperästä johtuvat rajoitukset. Sunisenlahden valuma-alue on kokonaisuudessaan rakennettua, jakautuen 24 osavaluma-alueeseen, joiden pinta-alat ja maankäyttö poikkeavat toisistaan. Alueella on kauttaaltaan sadevesiverkosto, jonka purku tapahtuu pääosin Sunisenlahdelle. Osa valuma-alueista on keskustamaisia, osa väljästi rakennettua pientaloaluetta. Joillakin valuma-alueilla on myös toimintoja, joiden hulevesien käsittely edellyttää myös haitta-aineiden poistamista. Valuma-alueella tutkittiin ravinnekuormituksen muodostumista näyttein 12 näytepisteellä. Typpikuormituksesta hulevesien osuus on noin 48 % ja fosforikuormituksesta hulevesien osuus on noin 36 %.

Uusiutuvan energian käyttömahdollisuudet Liikuntakeskus Pajulahdessa

Tämä diplomityö on tehty Lappeenrannan teknillisen yliopiston, Liikuntakeskus Pajulahden ja Nastolan Energiasäätiön yhteisprojektina. Työn tarkoituksena on tutkia aurinkosähköjärjestelmien taloudellista kannattavuutta ostosähkön korvaamisessa Liikuntakeskus Pajulahden kiinteistössä. Työssä tehdään laskelmat aurinkopaneelien tuotoista, tuotetun sähkön hinnasta, investointien takaisinmaksuajoista sekä tuotetun aurinkosähkön synnyttämistä hiilidioksidipäästövähenemistä. Lisäksi tarkastellaan energiaveron vaikutusta pientuotantolaitoksen kannattavuuteen. Tämän hetkisillä aurinkosähköjärjestelmien hinnoilla pystytään tuottamaan puhdasta, ympäristöystävällistä sähköä kilpailukykyiseen hintaan. Työssä tehdään yleiskatsaus myös muiden uusiutuviin energialähteisiin perustuvien tuotantomenetelmien käyttömahdollisuuksista. Yhtenä erityistarkastelunkohteena on Pajulahden monitoimihalliin vuonna 2008 suunniteltu vesistöä lämmönlähteenä käyttävä lämpöpumppujärjestelmä, jonka toteutukseen ei saatu tarvittavia lupia. Tarkastelussa tutkitaan myös aiemmin Suomessa toteutettuja vastaavia hankkeita ja niiden lupien saantia. Lisäksi on haettu tosiasioihin perustuvia argumentteja keskusteluun vesistölämmön hyödyntämisestä. Tarkastelun kohteena oleva vesistölämpöhanke voidaan todeta olevan erittäin kannattava, taloudellisesti sekä ympäristöllisesti. Tutkimuksen pohjalta Nastolan Energiasäätiölle tuotetaan havainnollinen ja selkeä aineisto aurinkoenergian hyödyntämismahdollisuuksista Nastolan kunnassa.

Opistorakennusten energiatehokkuuden parantaminen

Tämän diplomityön tavoitteena on selvittää Kymenlaakson Opiston energiatehokkuuden parantamista ja tutkia onko olemassa selvästi taloudellisempi sekä ekologisempi tapa kattaa Opiston lämmitystarve verrattuna nykyisin käytössä olevaan kaukolämpöön. Työn teoriaosuudessa tehdään katsaus rakennusten energiatehokkuuteen vaikuttaviin seikkoihin, lähienergian tuotantoon ja energiatehokkuuden parantamiseen liittyvään lainsäädäntöön ja säädöksiin. Useasta rakennuksesta koostuva kansanopisto tarjoaa mielenkiintoisen pohjan selvitystyölle ja suuri lämmitystehontarve yhdistettynä monille saneerauskohteille tyypillisiin ahtaisiin teknisiin tiloihin asettaa rajoituksia lämmitysjärjestelmän suunnittelulle. Soveltavassa osuudessa määritellään reunaehdot mahdolliselle kaukolämmön korvaavalle lämmitysratkaisulle. Tutkitaan vesistölämmön hyödyntämisen mahdollisuutta ja lasketaan aurinkosähkön ja -lämmön tuotantopotentiaalia. Maalämpöjärjestelmän mitoituksessa ja taloudellisessa vertailussa käytettiin apuna maalämpöjärjestelmiä toimittavia yrityksiä. Työssä saatujen tulosten perusteella maalämpöjärjestelmä on taloudellisesti kannattava isossa kohteessa, tosin järjestelmän asennukseen liittyy ahtaiden tilojen johdosta ongelmia. Maalämpö on myös selvästi ekologisempi, kuin nykyisin käytössä oleva kaukolämpö. Aurinkosähkön tuotannolle on Kymenlaakson Opistolla hyvä potentiaali ja sähkön tuotanto kohtaa hyvin sähkön käytön.

Developing Service-based Solutions for Water Treatment in Finnish Mining Industry

The aim of this master’s thesis is to analyze the mining industry customers' current and future needs for the water treatment services and discover new business development opportunities in the context of mine water treatment. In addition, the study focuses on specifying service offerings needed and evaluate suitable revenue generation models for them. The main research question of the study is: What kind of service needs related to water treatment can be identified in the Finnish mining industry? The literature examined in the study focused on industrial service classification and new service development process as well as the revenue generation of services. A qualitative research approach employing a case study method was chosen for the study. The present study uses customer and expert interviews as primary data source, complemented by archival data. The primary data was gathered by organizing total of 13 interviews, and the interviews were analyzed by using qualitative content analysis. The abductive-logic was chosen as the way of conducting scientific reasoning in this study. As a result, new service proposals were developed for Finnish mine industry suppliers. The main areas of development were on asset efficiency services and process support services. The service needs were strongly associated with suppliers’ know-how of water treatment process optimization, cost-effectiveness as well as on alternative technologies. The study provides an insight for managers that wish to pursue a water treatment services as a part of their business offering.

Geochemistry and water quality of Lake Qarun, Egypt

Water geochemistry is a very important tool for studying the water quality in a given area. Geology and climate are the major natural factors controlling the chemistry of most natural waters. Anthropogenic impacts are the secondary sources of contamination in natural waters. This study presents the first integrative approach to the geochemistry and water quality of surface waters and Lake Qarun in the Fayoum catchment, Egypt. Moreover, geochemical modeling of Lake Qarun was firstly presented. The Nile River is the main source of water to the Fayoum watershed. To investigate the quality and geochemistry of this water, water samples from irrigation canals, drains and Lake Qarun were collected during the period 2010‒2013 from the whole Fayoum drainage basin to address the major processes and factors governing the evolution of water chemistry in the investigation area. About 34 physicochemical quality parameters, including major ions, oxygen isotopes, trace elements, nutrients and microbiological parameters were investigated in the water samples. Multivariable statistical analysis was used to interpret the interrelationship between the different studied parameters. Geochemical modeling of Lake Qarun was carried out using Hardie and Eugster’s evolutionary model and a model simulated by PHREEQC software. The crystallization sequence during evaporation of Lake Qarun brine was also studied using a Jänecke phase diagram involving the system Na‒K‒Mg‒ Cl‒SO4‒H2O. The results show that the chemistry of surface water in the Fayoum catchment evolves from Ca- Mg-HCO3 at the head waters to Ca‒Mg‒Cl‒SO4 and eventually to Na‒Cl downstream and at Lake Qarun. The main processes behind the high levels of Na, SO4 and Cl in downstream waters and in Lake Qarun are dissolution of evaporites from Fayoum soils followed by evapoconcentration. This was confirmed by binary plots between the different ions, Piper plot, Gibb’s plot and δ18O results. The modeled data proved that Lake Qarun brine evolves from drainage waters via an evaporation‒crystallization process. Through the precipitation of calcite and gypsum, the solution should reach the final composition "Na–Mg–SO4–Cl". As simulated by PHREEQC, further evaporation of lake brine can drive halite to precipitate in the final stages of evaporation. Significantly, the crystallization sequence during evaporation of the lake brine at the concentration ponds of the Egyptian Salts and Minerals Company (EMISAL) reflected the findings from both Hardie and Eugster’s evolutionary model and the PHREEQC simulated model. After crystallization of halite at the EMISAL ponds, the crystallization sequence during evaporation of the residual brine (bittern) was investigated using a Jänecke phase diagram at 35 °C. This diagram was more useful than PHREEQC for predicting the evaporation path especially in the case of this highly concentrated brine (bittern). The predicted crystallization path using a Jänecke phase diagram at 35 °C showed that halite, hexahydrite, kainite and kieserite should appear during bittern evaporation. Yet the actual crystallized mineral salts were only halite and hexahydrite. The absence of kainite was due to its metastability while the absence of kieserite was due to opposed relative humidity. The presence of a specific MgSO4.nH2O phase in ancient evaporite deposits can be used as a paleoclimatic indicator. Evaluation of surface water quality for agricultural purposes shows that some irrigation waters and all drainage waters have high salinities and therefore cannot be used for irrigation. Waters from irrigation canals used as a drinking water supply show higher concentrations of Al and suffer from high levels of total coliform (TC), fecal coliform (FC) and fecal streptococcus (FS). These waters cannot be used for drinking or agricultural purposes without treatment, because of their high health risk. Therefore it is crucial that environmental protection agencies and the media increase public awareness of this issue, especially in rural areas.

Water vapor tightness of packages: methods and optimizing

Työn tarkoituksena oli testata jo tutkimuskeskuksella käytössä ollutta ja tutkimuskeskukselle tässä työssä kehitettyä pakkauksen vesihöyrytiiveyteen liittyvää mittausmenetelmää. Saatuja tuloksia verrattiin keskenään sekä materiaalista mitattuihin arvoihin. Elintarvikepakkauksia tutkittiin myös kosteussensoreiden, säilyvyyskokeen sekä kuljetussimuloinnin avulla. Optimoinnilla tutkittiin pakkauksen muodon vaikutusta vesihöyrytiiveyteen. Pakkauksen vesihöyrynläpäisyn mittaamiseen kehitetty menetelmä toimi hyvin ja sen toistettavuus oli hyvä. Verrattaessa sitä jo olemassa olleeseen menetelmään tulokseksi saatiin, että uusi menetelmä oli nopeampi ja vaati vähemmän työaikaa, mutta molemmat menetelmät antoivat hyviä arvoja rinnakkaisille näytteille. Kosteussensoreilla voitiin tutkia tyhjän pakkauksen sisällä olevan kosteuden muutoksia säilytyksen aikana. Säilyvyystesti tehtiin muroilla ja parhaan vesihöyrysuojan antoivat pakkaukset joissa oli alumiinilaminaatti- tai metalloitu OPP kerros. Kuljetustestauksen ensimmäisessä testissä pakkauksiin pakattiin muroja ja toisessa testissä nuudeleita. Kuljetussimuloinnilla ei ollutvaikutusta pakkausten sisäpintojen eheyteen eikä siten pakkausten vesihöyrytiiveyteen. Optimoinnilla vertailtiin eri muotoisten pakkausten tilavuus/pinta-ala suhdetta ja vesihöyrytiiveyden riippuvuutta pinta-alasta. Optimaalisimmaksi pakkaukseksi saatiin pallo, jonka pinta-ala oli pienin ja materiaalin sallima vesihöyrynläpäisy suurin ja vesihöyrybarrierin määrä pienin.

MANAGING STRATEGIC CHANGE:New Business Models Applying Wireless Technology as a Source of Competitive Edge

The diffusion of mobile telephony began in 1971 in Finland, when the first car phones, called ARP1 were taken to use. Technologies changed from ARP to NMT and later to GSM. The main application of the technology, however, was voice transfer. The birth of the Internet created an open public data network and easy access to other types of computer-based services over networks. Telephones had been used as modems, but the development of the cellular technologies enabled automatic access from mobile phones to Internet. Also other wireless technologies, for instance Wireless LANs, were also introduced. Telephony had developed from analog to digital in fixed networks and allowed easy integration of fixed and mobile networks. This development opened a completely new functionality to computers and mobile phones. It also initiated the merger of the information technology (IT) and telecommunication (TC) industries. Despite the arising opportunity for firms' new competition the applications based on the new functionality were rare. Furthermore, technology development combined with innovation can be disruptive to industries. This research focuses on the new technology's impact on competition in the ICT industry through understanding the strategic needs and alternative futures of the industry's customers. The change speed inthe ICT industry is high and therefore it was valuable to integrate the DynamicCapability view of the firm in this research. Dynamic capabilities are an application of the Resource-Based View (RBV) of the firm. As is stated in the literature, strategic positioning complements RBV. This theoretical framework leads theresearch to focus on three areas: customer strategic innovation and business model development, external future analysis, and process development combining these two. The theoretical contribution of the research is in the development of methodology integrating theories of the RBV, dynamic capabilities and strategic positioning. The research approach has been constructive due to the actual managerial problems initiating the study. The requirement for iterative and innovative progress in the research supported the chosen research approach. The study applies known methods in product development, for instance, innovation process in theGroup Decision Support Systems (GDSS) laboratory and Quality Function Deployment (QFD), and combines them with known strategy analysis tools like industry analysis and scenario method. As the main result, the thesis presents the strategic innovation process, where new business concepts are used to describe the alternative resource configurations and scenarios as alternative competitive environments, which can be a new way for firms to achieve competitive advantage in high-velocity markets. In addition to the strategic innovation process as a result, thestudy has also resulted in approximately 250 new innovations for the participating firms, reduced technology uncertainty and helped strategic infrastructural decisions in the firms, and produced a knowledge-bank including data from 43 ICT and 19 paper industry firms between the years 1999 - 2004. The methods presentedin this research are also applicable to other industries.

Patents in the Information and Communications Technology Sector - Development Trends, Problem Areas and Pressures for Change

The patent system was created for the purpose of promoting innovation by granting the inventors a legally defined right to exclude others in return for public disclosure. Today, patents are being applied and granted in greater numbers than ever, particularly in new areas such as biotechnology and information andcommunications technology (ICT), in which research and development (R&D) investments are also high. At the same time, the patent system has been heavily criticized. It has been claimed that it discourages rather than encourages the introduction of new products and processes, particularly in areas that develop quickly, lack one-product-one-patent correlation, and in which theemergence of patent thickets is characteristic. A further concern, which is particularly acute in the U.S., is the granting of so-called 'bad patents', i.e. patents that do not factually fulfil the patentability criteria. From the perspective of technology-intensive companies, patents could,irrespective of the above, be described as the most significant intellectual property right (IPR), having the potential of being used to protect products and processes from imitation, to limit competitors' freedom-to-operate, to provide such freedom to the company in question, and to exchange ideas with others. In fact, patents define the boundaries of ownership in relation to certain technologies. They may be sold or licensed on their ownor they may be components of all sorts of technology acquisition and licensing arrangements. Moreover, with the possibility of patenting business-method inventions in the U.S., patents are becoming increasingly important for companies basing their businesses on services. The value of patents is dependent on the value of the invention it claims, and how it is commercialized. Thus, most of them are worth very little, and most inventions are not worth patenting: it may be possible to protect them in other ways, and the costs of protection may exceed the benefits. Moreover, instead of making all inventions proprietary and seeking to appropriate as highreturns on investments as possible through patent enforcement, it is sometimes better to allow some of them to be disseminated freely in order to maximize market penetration. In fact, the ideology of openness is well established in the software sector, which has been the breeding ground for the open-source movement, for instance. Furthermore, industries, such as ICT, that benefit from network effects do not shun the idea of setting open standards or opening up their proprietary interfaces to allow everyone todesign products and services that are interoperable with theirs. The problem is that even though patents do not, strictly speaking, prevent access to protected technologies, they have the potential of doing so, and conflicts of interest are not rare. The primary aim of this dissertation is to increase understanding of the dynamics and controversies of the U.S. and European patent systems, with the focus on the ICT sector. The study consists of three parts. The first part introduces the research topic and the overall results of the dissertation. The second part comprises a publication in which academic, political, legal and business developments that concern software and business-method patents are investigated, and contentiousareas are identified. The third part examines the problems with patents and open standards both of which carry significant economic weight inthe ICT sector. Here, the focus is on so-called submarine patents, i.e. patentsthat remain unnoticed during the standardization process and then emerge after the standard has been set. The factors that contribute to the problems are documented and the practical and juridical options for alleviating them are assessed. In total, the dissertation provides a good overview of the challenges and pressures for change the patent system is facing,and of how these challenges are reflected in standard setting.

Polymer surface modification by atomic layer deposition

Current industrial atomic layer deposition (ALD) processes are almost wholly confined to glass or silicon substrates. For many industrial applications, deposition on polymer substrates will be necessary. Current deposition processes are also typically carried out at temperatures which are too high for polymers. If deposition temperatures in ALD can be reduced to the level applicable for polymers, it will open new interesting areas and applications for polymeric materials. The properties of polymers can be improved for example by coatings with functional and protective properties. Although the ALD has shown its capability to operate at low temperatures suitable for polymer substrates, there are other issues related to process efficiency and characteristics of different polymers where new knowledge will assist in developing industrially conceivable ALD processes. Lower deposition temperature in ALD generally means longer process times to facilitate the self limiting film growth mode characteristic to ALD. To improve process efficiency more reactive precursors are introduced into the process. For example in ALD oxide processes these can be more reactive oxidizers, such as ozone and oxygen radicals, to substitute the more conventionally used water. Although replacing water in the low temperature ALD with ozone or plasma generated oxygen radicals will enable the process times to be shortened, they may have unwanted effects both on the film growth and structure, and in some cases can form detrimental process conditions for the polymer substrate. Plasma assistance is a very promising approach to improve the process efficiency. The actual design and placement of the plasma source will have an effect on film growth characteristics and film structure that may retard the process efficiency development. Due to the fact that the lifetime of the radicals is limited, it requires the placement of the plasma source near to the film growth region. Conversely this subjects the substrate to exposure byother plasma species and electromagnetic radiation which sets requirements for plasma conditions optimization. In this thesis ALD has been used to modify, activate and functionalize the polymer surfaces for further improvement of polymer performance subject to application. The issues in ALD on polymers, both in thermal and plasma-assisted ALD will be further discussed.