Modelling the effect of temperature on height increment of Scots pine at high latitudes

Abstract

Computational and Experimental Analysis of Flow Field in the Diffusers of Centrifugal Compressors

Centrifugal compressors are widely used for example in process industry, oil and gas industry, in small gas turbines and turbochargers. In order to achieve lower consumption of energy and operation costs the efficiency of the compressor needs to be improve. In the present work different pinches and low solidity vaned diffusers were utilized in order to improve the efficiency of a medium size centrifugal compressor. In this study, pinch means the decrement of the diffuser flow passage height. First different geometries were analyzed using computational fluid dynamics. The flow solver Finflo was used to solve the flow field. Finflo is a Navier-Stokes solver. The solver is capable to solve compressible, incompressible, steady and unsteady flow fields. Chien's k-e turbulence model was used. One of the numerically investigated pinched diffuser and one low solidity vaned diffuser were studied experimentally. The overall performance of the compressor and the static pressure distribution before and after the diffuser were measured. The flow entering and leaving the diffuser was measured using a three-hole Cobra-probe and Kiel-probes. The pinch and the low solidity vaned diffuser increased the efficiency of the compressor. Highest isentropic efficiency increment obtained was 3\% of the design isentropic efficiency of the original geometry. It was noticed in the numerical results that the pinch made to the hub and the shroud wall was most beneficial to the operation of the compressor. Also the pinch made to the hub was better than the pinchmade to the shroud. The pinch did not affect the operation range of the compressor, but the low solidity vaned diffuser slightly decreased the operation range.The unsteady phenomena in the vaneless diffuser were studied experimentally andnumerically. The unsteady static pressure was measured at the diffuser inlet and outlet, and time-accurate numerical simulation was conducted. The unsteady static pressure showed that most of the pressure variations lay at the passing frequency of every second blade. The pressure variations did not vanish in the diffuser and were visible at the diffuser outlet. However, the amplitude of the pressure variations decreased in the diffuser. The time-accurate calculations showed quite a good agreement with the measured data. Agreement was very good at the design operation point, even though the computational grid was not dense enough inthe volute and in the exit cone. The time-accurate calculation over-predicted the amplitude of the pressure variations at high flow.

Sähkönjakeluverkon ja sähköasemien kehittämissuunnitelma

Tämän työn tavoitteena on tarkastella keskijänniteverkonja sähköasemien kehittämistarpeita kahdella kohdealueella Kymenlaakson Sähköverkko Oy:n verkossa. Tarkastelun pohjatiedoiksi selvitettiin verkon sähköinen nykytila, luotettavuus, verkon topologia, kuormitusten jakautuminen ja muodostettiintulevaisuuden kuormitusennusteet. Lisäksi tarkasteltiin sähköasemien korvattavuus. Keskeiseksi työn sisällöksi muodostui kevytsähköasemien eri sijoituspaikkojen kannattavuustarkastelut, ottaen huomioon uuden keskijännitesyöttöpisteen vaikutukset keskijänniteverkon vahvistustarpeisiin, häviöihin ja käyttövarmuuteen. Laskelmat suoritettiin elinkaarikustannusperiaatteella huomioiden investointien, keskeytyksestä aiheutuneen haitan, häviöiden, kunnossapidon javiankorjauksen kustannukset. Työn tuloksena saatiin investointistrategiaehdotukset, joiden pohjalta verkkoyhtiö voi tehdä lähitulevaisuuden ratkaisuja sekä valmistautua tuleviin investointeihin.

STYREENI-BUTADIEENILATEKSIN VALMISTUS EMULSIOPOLYMEROIN-NILLA JA LATEKSIN VISKOSITEETTIIN VAIKUTTAVAT TEKIJÄT.

Työn tavoitteina oli kirjallisuusosassa selvittää emulsiopolymeroinnin perusperiaatteet ja lateksien viskositeettiin vaikuttavat tekijät. Kokeellisessa osassa selvitettiin eräiden kaupallisten lateksien viskositeettiin vaikuttavia tekijöitä. Tutkittujen kaupallisten lateksien viskositeettien riippuvuudelle kuiva-ainepitoisuudesta saatiin tulokset, jotka ovat melko hyvin yhtäpitäviä kirjallisuudesta saatujen tulosten kanssa. Tutkitut lateksit erosivat lähinnä maksimaalisen polymeeripartikkelin tilavuusosuuden kohdalla kirjallisuudesta saaduista arvoista. Tämän todettiin johtuvan sähköisen kaksoiskerroksen ja partikkelin pintaan kiinnittyneiden ryhmien vaikutuksesta. Tämä tulos varmentui elektrolyyttipitoisuuden vaikutusta selvitettäessä. Elektrolyyttilisäys laski lateksien viskositeetteja ja pienensi lateksien välisiä viskositeettieroja. Lateksin pH:n nostolla oli selvästi viskositeettia kasvattava vaikutus. Tämä johtuu osaltaan myös sähköisen kaksoiskerroksen kasvamisesta happoryhmien ionisoituessa. Latekseja toisiinsa verrattaessa havaittiin selkeästi karboksyylihapon ja initiaattorista peräisin olevien happoryhmien määrän vaikutus lateksin viskositeetin muutokselle. Paljon karboksyylihappoa ja initiaattoria sisältävien lateksien viskositeetti muuttui selvästi voimakkaammin pH:n muuttuessa. Latekseissa havaittiin myös ero heikkojen karboksyylihapporyhmien ja vahvojen initiaattorista peräisin olevien happoryhmien ionisoitumisen välillä. Vahvat happoryhmät ionisoituivat matalammassa pH:ssa kuin vahvat ja nostavat näin myös viskositeettia matalammassa pH:ssa kuin karboksyylihapporyhmät. Anionisen emulgaattorin lisäyksellä ei havaittu olevan kovinkaan suurta vaikutusta viskositeettiin. Partikkelikoon vaikutusta voitiin tutkia ainoastaan prosessista saadun mittausaineiston avulla. Partikkelikoon vaikutukset peittyivät suurelta osin muiden tekijöiden alle. Ainoastaan yhdelle lateksityypille saatiin selkeä riippuvuus partikkelikoon ja viskositeetin välille. Riippuvuus noudattaa kirjallisuudesta saatuja tietoja eli partikkelikoon kasvaessa viskositeetti laskee. Myös lateksin viskositeetin riippuvuus käytetystä leikkaus-nopeudesta noudattaa hyvin kirjallisuudesta saatuja tuloksia. Lateksin viskositeetti laskee leikkausnopeuden kasvaessa.

A Practical Micro Mechanical Model Based Local Approach Methodology for the Analysis of Ductile Fracture of Welded T-Joints

This thesis concentrates on developing a practical local approach methodology based on micro mechanical models for the analysis of ductile fracture of welded joints. Two major problems involved in the local approach, namely the dilational constitutive relation reflecting the softening behaviour of material, and the failure criterion associated with the constitutive equation, have been studied in detail. Firstly, considerable efforts were made on the numerical integration and computer implementation for the non trivial dilational Gurson Tvergaard model. Considering the weaknesses of the widely used Euler forward integration algorithms, a family of generalized mid point algorithms is proposed for the Gurson Tvergaard model. Correspondingly, based on the decomposition of stresses into hydrostatic and deviatoric parts, an explicit seven parameter expression for the consistent tangent moduli of the algorithms is presented. This explicit formula avoids any matrix inversion during numerical iteration and thus greatly facilitates the computer implementation of the algorithms and increase the efficiency of the code. The accuracy of the proposed algorithms and other conventional algorithms has been assessed in a systematic manner in order to highlight the best algorithm for this study. The accurate and efficient performance of present finite element implementation of the proposed algorithms has been demonstrated by various numerical examples. It has been found that the true mid point algorithm (a = 0.5) is the most accurate one when the deviatoric strain increment is radial to the yield surface and it is very important to use the consistent tangent moduli in the Newton iteration procedure. Secondly, an assessment of the consistency of current local failure criteria for ductile fracture, the critical void growth criterion, the constant critical void volume fraction criterion and Thomason's plastic limit load failure criterion, has been made. Significant differences in the predictions of ductility by the three criteria were found. By assuming the void grows spherically and using the void volume fraction from the Gurson Tvergaard model to calculate the current void matrix geometry, Thomason's failure criterion has been modified and a new failure criterion for the Gurson Tvergaard model is presented. Comparison with Koplik and Needleman's finite element results shows that the new failure criterion is fairly accurate indeed. A novel feature of the new failure criterion is that a mechanism for void coalescence is incorporated into the constitutive model. Hence the material failure is a natural result of the development of macroscopic plastic flow and the microscopic internal necking mechanism. By the new failure criterion, the critical void volume fraction is not a material constant and the initial void volume fraction and/or void nucleation parameters essentially control the material failure. This feature is very desirable and makes the numerical calibration of void nucleation parameters(s) possible and physically sound. Thirdly, a local approach methodology based on the above two major contributions has been built up in ABAQUS via the user material subroutine UMAT and applied to welded T joints. By using the void nucleation parameters calibrated from simple smooth and notched specimens, it was found that the fracture behaviour of the welded T joints can be well predicted using present methodology. This application has shown how the damage parameters of both base material and heat affected zone (HAZ) material can be obtained in a step by step manner and how useful and capable the local approach methodology is in the analysis of fracture behaviour and crack development as well as structural integrity assessment of practical problems where non homogeneous materials are involved. Finally, a procedure for the possible engineering application of the present methodology is suggested and discussed.

Performance Improvement of Centrifugal Compressor Stage with Pinched Geometry or Vaned Diffuser

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.

Targeting of caries prevention at preschool children, a practice based study

Aim and design: To evaluate an oral health program directed to expecting families and their children. The intervention was carried out in one of the four health care areas of the city of Turku. Another area acted as a control. Subjects and methods: Children (n = 1217), born between January 1, 1998 and June 30, 1999, in the respective health care areas were screened for mutans streptococci bacteria (MS), and their caretakers were interviewed when the child was 18 months old. MScolonization was used as the child’s risk indicator. Intensified health education and the use of xylitol lozenges targeted at the children at risk were the main elements of the program. Controls and the non-MS-colonized children received routine prevention –examination and education at the ages of three and five years. Altogether 794 subjects were followed for 42 months after receiving consent from their caretakers. Associations of oral-health-related factors with MS colonization and caries increment were studied inside the control group. Results: MS colonization associated with the occupation of the caretaker and ethnicity. The program was effective in white-collar families; prevented fraction being 67 %. In blue-collar families no effect was achieved. At the age of five years, caries increment was strongly related to the occupation of the caretaker, MS at 18 months, child’s sugar use, night feeding, use of thirst quencher at the age of 18 months, and father’s reported oral health. Conclusions: Programs targeted at MS-colonized children can reduce caries in whitecollar families. A program mainly based on activity at home seems to favor white-collar families, whereas different kind of support is needed for the blue-collar families.

Time Varying Conditional Correlation Between Stock And Bond Returns: Evidence From CIVETS Nations

This thesis estimates long-run time variant conditional correlation between stock and bond returns of CIVETS (Colombia, Indonesia, Vietnam, Egypt, Turkey, and South Africa) nations. Further, aims to analyse the presence of asymmetric volatility effect in both asset returns, as well as, obverses increment or decrement in conditional correlation during pre-crisis and crisis period, which lead to make a reliable diversification decision. The Constant Conditional Correlation (CCC) GARCH model of Bollerslev (1990), the Dynamic Conditional Correlation (DCC) GARCH model (Engle 2002), and the Asymmetric Dynamic Conditional Correlation (ADCC) GARCH model of Cappiello, Engle, and Sheppard (2006) were implemented in the study. The analyses present strong evidence of time-varying conditional correlation in CIVETS markets, excluding Vietnam, during 2005-2013. In addition, negative innovation effects were found in both conditional variance and correlation of the asset returns. The results of this study recommend investors to include financial assets from these markets in portfolios, in order to obtain better stock-bond diversification benefits, especially during high volatility periods.

Kotkan kaupungin ja lähialueen sähkönjakeluverkon kehittämissuunnitelma

Kotkan jakelualueella käytetään historiallisista syistä keskijänniteverkossa kahta jänniteta-soa, 10 kV ja 20 kV. Eri jännitetasojen lisäksi Kotkan jakelualueen 110/20 päämuuntajien kytkentäryhmänä on käytössä YNyn0, kun taas muualla verkossa käytetään YNd11 kyt-kentäryhmää. Jännitetasoista ja kytkentäryhmistä johtuen Kotkan jakeluverkon yhteenkyt-kettävyys ympäröivän verkon kanssa on haastavaa. Työn tavoitteena on selvittää Kotkan kaupungin keskijänniteverkon nykytila ja käytettä-vyys häiriötilanteissa pahimpana mahdollisena aikana, sekä löytää mahdolliset ongelma-kohdat. Verkon nykytila tarkasteltiin verkkotietojärjestelmän avulla käyttäen laskennallisia tuloksia, jotka skaalattiin vastaamaan kovemman pakkastalven kuormitusta. Skaalaus teh-tiin useamman vuoden takaiseen tilanteeseen, jolloin yleinen taloustilanne oli parempi ja verkon kuormitus suurempi, jolloin verkko ei tule alimitoitetuksi taloustilanteen parantuessa. Tulevaisuuden varalta muodostettiin alueen tulevaisuuden kuormitusennusteet käyttämällä historiatietoja sekä tulevaisuuden näkymiä apuna. Työn keskeisimmäksi sisällöksi muodostui selvittää tarve usean käyttöjännitteen säilyttä-miselle sekä erilaisten kytkentäryhmien ylläpitämiseen ja kosketusjänniteongelman ratkai-seminen. Alueen sähköverkon kehittämiseksi tehtiin useita eri vaihtoehtoja, joita vertailtiin elinkaarikustannusperiaatteella toisiinsa. Vertailun pohjalta saatiin investointistrategia ehdo-tukset, joiden pohjalta verkkoyhtiö voi tehdä tulevaisuuteen sijoittuvia ratkaisuja.