Transfer of MPEG-2 Transport Stream over MPLS

This study examines how MPEG-2 Transport Stream, used in DVB-T video transmission, can be reliably and efficiently transferred to remote locations over an MPLS network. All the relevant technologies used in this scenario are also discussed in the study. This study was done for Digita Oy, which is a major radio and television content distributor in Finland. The theoretical part of the study begins with the introduction to MPLS technology and continues with explanation of IP Multicast and its components. The fourth section discusses MPEG-2 and the formation and content of MPEG-2 Transport Stream. These technologies were studied in relevant literature and RFC documentation. After the theoretical part of the study, the test setup and the test cases are presented. The results of the test cases, and the conclusions that can be drawn based on them, are discussed in the last section of the study. The tests showed that it is possible to transfer digital video quite reliably over an MPLS network using IP Multicast. By configuring the equipment correctly, the recovery time of the network in case of a failure can be shortened remarkably. Also, the unwanted effect of other traffic on the critical video traffic can be eliminated by defining the Quality of Service parameters correctly. There are, however, some issues that need to be tested further before this setup can be used in broadcast networks. Reliable operation of IP Multicast and proper error correction are the main subjects for future testing.

Non-surgical transfer of 4',6'-diamidino-2-phenylindole-stained equine embryos

Selostus: Hevosen alkioiden värjääminen DAPI:lla ennen vastaanottajaan siirtoa

The transfer of 137Cs through the soil-plant-sheep food chain in different pasture ecosystems

Selostus: Radiocesiumin kulkeutuminen eri laidunekosysteemien maa-ruoho-lammas -ravintoketjussa

Production of calves following nonsurgical transfer of fresh and refrigerated bovine demi-embryos

Selostus: Vasikoiden tuottaminen tuoreilla ja kylmäsäilytetyillä halkaistuilla alkioilla

Applicability of Power-Line Communications to Data Transfer of On-line Condition Monitoring of Electrical Drives

The research of power-line communications has been concentrated on home automation, broadband indoor communications and broadband data transfer in a low voltage distribution network between home andtransformer station. There has not been carried out much research work that is focused on the high frequency characteristics of industrial low voltage distribution networks. The industrial low voltage distribution network may be utilised as a communication channel to data transfer required by the on-line condition monitoring of electric motors. The advantage of using power-line data transfer is that it does not require the installing of new cables. In the first part of this work, the characteristics of industrial low voltage distribution network components and the pilot distribution network are measured and modelled with respect topower-line communications frequencies up to 30 MHz. The distributed inductances, capacitances and attenuation of MCMK type low voltage power cables are measured in the frequency band 100 kHz - 30 MHz and an attenuation formula for the cables is formed based on the measurements. The input impedances of electric motors (15-250 kW) are measured using several signal couplings and measurement based input impedance model for electric motor with a slotted stator is formed. The model is designed for the frequency band 10 kHz - 30 MHz. Next, the effect of DC (direct current) voltage link inverter on power line data transfer is briefly analysed. Finally, a pilot distribution network is formed and signal attenuation in communication channels in the pilot environment is measured. The results are compared with the simulations that are carried out utilising the developed models and measured parameters for cables and motors. In the second part of this work, a narrowband power-line data transfer system is developed for the data transfer ofon-line condition monitoring of electric motors. It is developed using standardintegrated circuits. The system is tested in the pilot environment and the applicability of the system for the data transfer required by the on-line condition monitoring of electric motors is analysed.

Role of Membrane Transporters, P-Glycoprotein and Mrp1, in The Placental Transfer of Drugs With Special Reference to Saquinavir and Quetiapine

Drug transporting membrane proteins are expressed in various human tissues and blood-tissue barriers, regulating the transfer of drugs, toxins and endogenous compounds into or out of the cells. Various in vitro and animal experiments suggest that P-glycoprotein (P-gp) forms a functional barrier between maternal and fetal blood circulation in the placenta thereby protecting the fetus from exposure to xenobiotics during pregnancy. The multidrug resistance-associated protein 1 (MRP1) is a relatively less studied transporter protein in the human placenta. The aim of this study series was to study the role of placental transporters, apical P-gp and basal MRP1, using saquinavir as a probe drug, and to study transfer of quetiapine and the role of P-gp in its transfer in the dually perfused human placenta/cotyledon. Furthermore, two ABCB1 (encoding P-gp) polymorphisms (c.3435C>T, p.Ile1145Ile and c.2677G>T/A, p.Ala893Ser/Thr) were studied to determine their impact on P-gp protein expression level and on the transfer of the study drugs. Also, the influence of the P-gp protein expression level on the transfer of the study drugs was addressed. Because P-gp and MRP1 are ATP-dependent drug-efflux pumps, it was studied whether exogenous ATP is needed for the function of ATP-dependent transporter in the present experimental model. The present results indicated that the addition of exogenous ATP was not necessary for transporter function in the perfused human placental cotyledon. Saquinavir and quetiapine were both found to cross the human placenta; transplacental transfer (TPTAUC %) for saquinavir was <0.5% and for quetiapine 3.7%. Pharmacologic blocking of P-gp led to disruption of the blood-placental barrier (BPB) and increased the placental transfer of P-gp substrate, saquinavir, into the fetal circulation by 6- to 8-fold. In reversed perfusions P-gp, MRP1 and possibly OATP2B1 had a negligible role in the fetal-to-maternal transfer of saquinavir. The TPTAUC % of saquinavir was about 100-fold greater from the fetal side to the maternal side compared with the maternal-to-fetal transfer. P-gp activity is not likely to modify the placental transfer of quetiapine. Higher P-gp protein expression levels were associated with the variant allele 3435T, but no correlation was found between the TPTAUC % of saquinavir and placental P-gp protein expression. The present results indicate that P-gp activity drastically affects the fetal exposure to saquinavir, and suggest that pharmacological blockade of the P-gp activity during pregnancy may pose an increased risk for adverse fetal outcome. The blockade of P-gp activity could be used in purpose to obtain higher drug concentration to the fetal side, for example, in prevention (to decrease virus transfer to fetal side) or in treating sick fetus.

Transfer of Administrative HR Services to Global Service Center in Poland

Liiketoimintaa tukevien palvelujen etätuotanto edustaa uutta kansainvälistymisen muotoa. Kehittyvien markkinoiden nousu yhdistettynä yritysten arvoketjutoimintojen kansainvälistymiseen on luonut yrityksille kasvavan paineen etsiä parasta sijaintia toiminnoilleen. Monikansalliset yritykset ovat yhä useammin korvanneet paikallisia henkilöstöpalvelujaan siirtymällä globaaliin malliin jaettujen palvelujen tuotannossa. Tämä diplomityö on toteutettu tukeakseen UPM:n henkilöstöhallintoa globaalin palvelukeskuksen perustamisessa Puolaan. Tutkimuksen tavoitteena on laajentaa käsitystä henkilöstöpalvelujen tarjontamallin uudistamiseen johtaneista tekijöistä ja motiiveista. Empiirisen tutkimuksen tärkein tavoite on tukea rekrytoinnin hallinnollisten töiden siirtoa globaaliin palvelukeskukseen palvelun laadun säilyessä vähintään aikaisemmalla tasolla. Tutkimuksen tulokset painottavat strategista näkökulmaa muutokseen. Strategiset syyt UPM:n henkilöstöhallinnon globaalin palvelukeskuksen perustamiselle sisältävät ylikapasiteetin ja päällekkäisten toimintojen vähentämisen eri maissa. Muutos lisää palvelun joustavuutta sekä edesauttaa toiminnan läpinäkyvyyttä, ennustettavuutta ja kustannusten valvontaa. Onnistuneesti toteutetut jaetut palvelut voivat toimia hyvänä lähtökohtana tehokkaiden henkilöstöpalvelujen tuottamiselle.

The Application of Enterprise Architecture Approach to Military Concept Development–Case Study

Abstract—Concept development and experimentation (CD&E) plays an important role in driving strategic transformation in the military community. Defence architecture frameworks, such as the NATO architecture framework, are considered excellent means to support CD&E. There is not much empirical evidence, however, to indicate how enterprise architectures (EA) are applied in the military community or particularly in military CD&E. Consequently, this paper describes and discusses empirical application of the EA approach in CD&E. The research method in the paper is a case study. Situational method engineering (SiME) is used as a framework to adapt the EA approach to the case project of the paper. The findings of the paper suggest that the EA is applicable to CD&E work, although all aspects of the original concept could not be expressed in the EA model of the case project. The results also show that the SiME method can support in applying the EA framework to the CD&E in the case project.

Benefits and challenges of Enterprise Resource Planning for Pakistani SMEs

Enterprise resource planning (ERP) software is used to combine all the functions happening inside the organization with the help of one software. All the data is centralized which makes it easy to manage information for all participants. The literature on ERP is studied thoroughly the whole process of adoption till the implementation and final evaluations. But studies that focus on small and medium sized enterprises are limited in number when compared to the large scale enterprises. In case of Pakistan, research is very limited. In this thesis, the author tries to analyze the current status of SMEs usage of ERP system. The benefits obtained and challenges faced by SMEs of Pakistan are studied. Framework presented by Shang and Seddon (2000) is used to understand the benefits obtained by the SMEs in Pakistan. This is a comprehensive framework that classifies the benefits obtained by the ERP adoption, into five categories: operational benefits, managerial benefits, Strategic benefits, IT benefits, and Organizational benefits. The results show that SMEs of Pakistan are also getting many benefits after adoption of ERP. Most of the firms had implemented SAP software. Operational benefits were mentioned by all the firms. The most important benefits were report generation, quick access to critical information, better product and cost planning. Respondents also mentioned that they had reduced corruption as a result of ERP implementation. It is also an important benefit considering high corruption rate in Pakistan. Along with benefits, challenges faced by Pakistani SMEs included infrastructure problems like electricity, difficulties with integration of one module with other module, costs of adoption and lack of skilled ERP consultants. Further studies in this regard can be conducted on cloud based ERP which is fast growing all around the world.

The Role of an Enterprise Portal in Knowledge Management Strategy, Case: Private Equity Investor

Työ tutkii yritysportaalin roolia organisaation tietojohtamisessa. Tutkimusongelman ratkaisemiseksi luodaan viitekehys, jossa yritysportaalin ja tietojohtamisen teoriat linkittyvät. Työn empiirisessä osassa viitekehys on pohjana case-yritykselle rakennettavalle yritysportaalille. Laadullinen tutkimus käsittää teoriaosuuden sekä osallistuvaan case-tutkimukseen perustuvan empiriaosuuden. Työn runko muodostuu kahden vastakkaisen tietojohtamisajattelun vuoropuhelusta, jotka ovat informaatioteknologiaan- ja strategiseen johtamiseen perustuvat näkökulmat. Toimivan tietojohtamismallin täytyy sisältää molemmat aspektit. Jokainen organisaatio tarvitsee informaation hallintaan liittyviä toiminnallisuuksia ja täten eksplisiittisen tiedon hallinta tietojärjestelmien avulla on onnistuneen tietojohtamisen kulmakiviä. Tätä perusinfrastruktuuria on mahdollista laajentaa hiljaisen tiedon hallintaan perustuvilla tietojohtamismenetelmillä. Työn ratkaisu näiden kahden näkemyksen, 'kovan' informaatioteknogiaan painottuvan sekä 'pehmeän' ihmisnäkökulman integrointiin, on yritysportaali. Työssä käytettävä yritysportaalin viitekehys rakentuu kolmeen päätoiminnallisuuteen; sisällönhallintaan, yhteistyöominaisuuksiin ja liiketoimintatiedon hallintaan. Työ todistaa yhteyden viitekehyksen sekä tietojohtamisen perusmallien, kuten tietojohtamisen prosessimallin sekä tietoympäristöjen välillä. Yritysportaali voi täten toimia, ei ainoastaan yksittäisten tietojohtamistyökalujen implementoinnissa, vaan tietojohtamisstrategian luomisen apuna tarjoten alustan tai 'katalyytin' kokonaisvaltaiselle tietojohtamiselle.

Prediction of heat transfer on kraft recovery boiler

Työssä tutkittiin Andritz-Ahlstrom toimittamien soodakattiloiden lämmönsiirtoa ANITA 2.20- suunnitteluohjelmalla feedback- laskentaa apuna käyttäen. Data laskentaan saatiin kattiloiden takuukokeissa mitatuista arvoista. Mittaukset on suoritettiin Andritz-Ahlstromin henkilökunnan toimesta tehdashenkilökunnan avustuksella. Feedback -laskenta tapahtui mittaustulosten perusteella, joten tiettyä virhettä luonnollisesti esiintyi. Aluksi laskettiin taseet molempien ekojen yli erikseen sekä molemmat yhdessä Excel-taulukkolaskentaohjelmalla. Täältä saatiin oletettu savukaasuvirtaus kattilassa. Tämän jälkeen lämpöpintoja muokattiin todellisuutta vastaaviksi yleislikaisuuskerrointa muuttamalla (overall fouling factor). Kertoimet ovat liikkuivat noin 0.4 ja 1.6 välillä riipuen kattilan tyypistä ja ANITAn oletuksesta lämpöpintojen likaisuudelle. Havaittin että yhtä varsinaista syytä lämpöpintojen eroavaisuuteen oletetusta ei saatu. Syitä toiminnan poikkeamiseen oli monia. Mm. etukammion koolla havaittiin olevan suurtakin vaikutusta tulistimien, etenkin savukaasuvirrassa ensimmäisen tulistimen toimintaan. Yleisesti todettiin muiden tulistimien vastaavan oletettua toimintaa. Keittopinnan ja ekonomiserien toimintaa tutkittiin hivenen suppeammin ja havaittiin niiden toimivan huomattavasti stabiilimmin kuin tulistimien. Likaisuus kertoimet oletetusta vaihtelivat noin ±20 %.

Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Integration of Electronic Commerce and Enterprise Systems

The necessity of EC (Electronic Commerce) and enterprise systems integration is perceived from the integrated nature of enterprise systems. The proven benefits of EC to provide competitive advantages to the organizations force enterprises to adopt and integrate EC with their enterprise systems. Integration is a complex task to facilitate seamless flow of information and data between different systems within and across enterprises. Different systems have different platforms, thus to integrate systems with different platforms and infrastructures, integration technologies, such as middleware, SOA (Service-Oriented Architecture), ESB (Enterprise Service Bus), JCA (J2EE Connector Architecture), and B2B (Business-to-Business) integration standards are required. Huge software vendors, such as Oracle, IBM, Microsoft, and SAP suggest various solutions to address EC and enterprise systems integration problems. There are limited numbers of literature about the integration of EC and enterprise systems in detail. Most of the studies in this area have focused on the factors which influence the adoption of EC by enterprise or other studies provide limited information about a specific platform or integration methodology in general. Therefore, this thesis is conducted to cover the technical details of EC and enterprise systems integration and covers both the adoption factors and integration solutions. In this study, many literature was reviewed and different solutions were investigated. Different enterprise integration approaches as well as most popular integration technologies were investigated. Moreover, various methodologies of integrating EC and enterprise systems were studied in detail and different solutions were examined. In this study, the influential factors to adopt EC in enterprises were studied based on previous literature and categorized to technical, social, managerial, financial, and human resource factors. Moreover, integration technologies were categorized based on three levels of integration, which are data, application, and process. In addition, different integration approaches were identified and categorized based on their communication and platform. Also, different EC integration solutions were investigated and categorized based on the identified integration approaches. By considering different aspects of integration, this study is a great asset to the architectures, developers, and system integrators in order to integrate and adopt EC with enterprise systems.