Fotokatalyyttinen kalvonpesu

Fotokatalyysillä tarkoitetaan spontaania kemiallista reaktiota, joka tapahtuu fotokatalyytin absorboidessa valoa. Reaktio voi tapahtua joko katalyytin pinnalla tai sen läheisyydessä, mutta fotokatalyytti pysyy reaktiossa muuttumattomana. Ominaisuuksiltaan paras ja eniten tutkittu fotokatalyyttinen materiaali on titaanidioksidi, jolla on säteilytettynä kyky hajottaa orgaanisia molekyylejä hiilidioksidiksi ja vedeksi. Fotokatalyysin käyttömahdollisuuksia tutkitaan membraanikalvojen puhdistamisessa kalvojen käyttöiän ja erotustehokkuuden parantamiseksi. Nykyisin kalvojen puhdistamiseen käytetään useimmiten kemiallista pesua, jonka tuloksena on usein haitallisia yhdisteitä sisältävä liuos. Fotokatalyyttinen puhdistus voisi olla ratkaisu ongelmaan, sillä sen avulla voitaisiin puhdistamisessa käytettävien kemikaalien ja siinä muodostuvien jätteiden määrää vähentää. Tämän työn kokeellisessa osassa tutkittiin polyvinyylideenifluoridikalvon (PVDF) kestävyyttä ja puhdistumista fotokatalyyttisissä reaktioissa. PVDF:n on todettu olevan erinomainen kalvomateriaali, koska se on termisesti stabiili ja se kestää hyvin kemikaaleja, kuten orgaanisia liuottimia, happoja ja emäksiä. Työssä todettiin PVDF-kalvon puhdistuvan UV/TiO2-käsittelyn avulla. Kalvo puhdistui parhaiten, kun käytettiin 0,425 m- % TiO2-liuosta. Puhdistumista havainnoitiin sekä puhtaan veden vuon mittauksilla että värjäämällä käsiteltyjä kalvoja ja mittaamalla niiden värinintensiteetti.

Alikriittisen veden käyttö kromatografisessa erotuksessa

Alikriittisellä vedellä tarkoitetaan paineistettua vettä, joka on kriittisen lämpötilansa (374 °C) alapuolella nestemäisessä tilassa. Veden tiheys pienenee lämpötilan kasvaessa Veden liuotinominaisuuksia voidaan säädellä lämpötilan avulla. Veden pintajännitys, viskositeetti, tiheys ja polaarisuus pienenevät lämpötilan kasvaessa, ja alikriittisen veden aineominaisuudet muuttuvat lähemmäksi orgaanista liuotinta. Alikriittisen veden dielektrisyysvakion aleneminen johtuu pääasiassa lämpötilan vaikutuksesta ja vain vähän paineen vaikutuksesta. Alikriittistä vettä on käytetty liuottimena uutossa, mutta nyt myös alikriittinen kromatografia on kehittymässä oleva erotusmenetelmä. Työn kokeellisessa osassa kehitettiin kromatografinen laitteisto alikriittiselle vedelle, jolla tutkittiin sokerialkoholien ja sokerien kromatografista erotusta alikriittisen veden avulla. Lisäksi tutkittiin sokerialkoholien, sokereiden ja stationäärifaasien termistä kestävyyttä. Tutkittavina komponentteina olivat sorbitoli, mannitoli, ksylitoli, arabinoosi, mannoosi, ksyloosi, maltoosi ja ramnoosi. Stationäärifaaseina käytettiin makrohuokoista funktionalisoimatonta polystyreenidivinyylibentseenikopolymeeriä, sekä vahvoja ja heikkoja divinyylibentseenillä ristisilloitettuja kationinvaihtohartseja, jotka olivat joko Na+- tai Ca2+-ionimuodoissa. Veden lämpötilan nostaminen vaikuttaa sekä kromatografisen stationäärifaasin tilavuusmuutoksiin että näytekomponenttien ominaisuuksiin. Vahvoilla kationinvaihtimilla havaittiin termisten tilavuusmuutosten riippuvan ionimuodosta: Na+-muotoiset hartsit turpoavat ja Ca2+-muotoiset kutistuvat lämpötilan noustessa. Heikot kationinvaihtimet kutistuvat molemmissa ionimuodoissa, mutta Ca2+-muoto kutistuu Na+-muotoa voimakkaammin. Näytekomponenteista sokerialkoholien havaittiin kestävän paremmin korkeita lämpötiloja kuin sokerien. Sokerialkoholeista kestävimmäksi havaittiin ksylitoli ja sokereista ramnoosi. Tutkittavien komponenttien piikkien havaittiin kapenevan, häntimisen vähenevän, ja piikkien eluoituvan aikaisemmin riippuen käytettävästä stationäärifaasista. Ca2+-muotoisen vahvan kationinvaihtimen kompleksinmuodostuskyky heikkeni lämpötilan kasvaessa. Näytekomponenttien erotus ei kuitenkaan parantunut lämpötilan noustessa tutkituilla stationäärifaaseilla.

Production of Chemicals from Woody Biomass by Wet Oxidation

The production of chemicals from sawdust by wet oxidation has been investigated. Two different concentrations of sawdust; 54054 mg/l and 32683 mg/l were used in the study. The wet oxidation operating conditions were; 175 deg.C – 225 deg.C, 1MPa Oxygen, and 40 minutes to 120 minutes reaction time. Carboxylic acids were among the chemicals produced in the process. The total yield of carboxylic acids was found to increase with temperature. Also, higher yields of carboxylic acids were observed at a lower sawdust concentration. This was probably due to the high oxygen-biomass ratio at lower sawdust concentration. Higher oxygen availability at low sawdust concentration resulted in increased conversion of the sawdust; hence the higher yields of carboxylic acids. At lower sawdust concentration, a total carboxylic acid yield of 25.59 wt% was attained at 200 deg.C and 40 minutes reaction time. At higher sawdust concentration, a total carboxylic acid yield of 15.57 wt% was attained at 200 deg.C and 40-minutes reaction time. The carboxylic acids identified include formic acid, acetic acid, succinic acid and oxalic acid. The optimum temperature for the production of formic acid was found to be 200 deg.C, while the optimum temperature for the production of acetic acid was found to be 225 deg.C. A temperature of 225 deg.C and relatively short reaction time of 10 minutes was found to be the optimal condition for the production of succinic acid. Formic acid was produced in the highest yield, with an optimal yield of 13.69wt %, when the reaction temperature and time are 200 deg.C and 40 minutes respectively. The yield of formic acid was found to decrease significantly when further increasing the temperature to 225 deg.C. This was presumably due to thermal decomposition of formic acid at relatively higher temperature. However, the yield of acetic acid was found to steadily increase with temperature. This is because acetic is more thermally stable than formic acid. The yield of acetic acid did not decrease after the temperature was increased to 225 deg.C. Optimal yield of acetic acid (7.98wt %) was achieved at; 225 deg.C, and 40 minutes reaction time. Succinic acid was produced only at temperatures of 200 deg.C and 225 deg.C. Optimal yield of succinic acid (5.66wt %) was attained under the following conditions; 32683 mg/l, 225 deg.C, 1MPa O2, and 10-minutes reaction time. Oxalic acid was produced in the lowest yield and, less frequently. The optimal yield of oxalic acid (4.02 wt%) was attained at 175 deg.C and 80-minutes of reaction time The Total Organic Carbon (TOC) is found to be higher when increasing the operating temperature, thus suggesting that more organic compounds are formed at higher temperatures. The identified carboxylic acids could only account for less than 30% of the measured COD content of the various wet oxidation samples. This implies that some other unidentified compounds (reaction products) must have been present. In general, wet oxidation seems to be an effective method for converting lignocellulosic biomass into useful chemicals. Relatively higher temperatures have been found to favor the production of carboxylic acids from sawdust.

Kunnallisen jätevedenkäsittelyn tehostaminen membraanitekniikan avulla – esimerkkinä Savitaipaleen jätevedenpuhdistamo

Työssä tutkittiin mahdollisuutta tehostaa kunnallista jätevedenpuhdistusta membraanitekniikkaa käyttäen. Teoriaosassa perehdyttiin kunnallisen jäteveden omi-naisuuksiin ja perinteiseen puhdistusprosessiin. Tämän lisäksi membraanien yleisiä ominaisuuksia, membraanityyppien kykyä erottaa jäteveden sisältämiä yhdisteitä sekä erilaisia mahdollisuuksia membraanisuodatukselle perinteisen jäteve-denpuhdistusprosessin yhteydessä käytiin läpi. Kokeellisessa osassa keskityttiin Savitaipaleen puhdistamon puhdistetun jäteveden laadun parantamiseen membraanisuodatukseen perustuvalla jälkikäsittely-yksiköllä eli tertiäärisuodatuksella. Erilaisia paineavusteisia membraanitekniikoita (MF, UF, NF ja RO) tutkittiin jäteveden puhdistamiseksi ja erotustehokkuuden vertailemiseksi. Tavoitteena oli löytää tehokas ja käytännössä toimiva tapa poistaa fosforia ja typpeä puhdistetusta jätevedestä. Tasomaisilla membraaneilla tehdyissä suodatuksissa MF-membraanit poistivat tehokkaasti fosforia (97 – 98 %) sekä kiintoainesta (100 %) jätevedestä. RO-membraanit alensivat fosfori- (100 %) ja typpipitoisuutta (90 – 94 %) tehokkaasti, poistaen myös liuenneita orgaanisia yhdisteitä (DOC, 90 – 94 %). Mikrosuodatukseen perustuvilla onttokuitumembraaneilla saavutettiin tehokkaan fosforinpoiston lisäksi tasainen kapasiteetti suodatuksen aikaista puhdistusmene-telmää optimoimalla. Pitoisuusalenemat olivat myös erittäin korkeita fosforille (97 – 99 %), kiintoaineelle (100 %), sameudelle (96 – 99 %) sekä COD:lle (38 – 55 %). Tulosten perusteella membraanitekniikkaan perustuva onttokuitusuodatus olisi tehokas ja toimiva jälkikäsittelyprosessi fosforinpoistoon ja jäteveden laadun pa-rantamiseen. Typen poistamiseen parhaiten toimi RO-membraani.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

Suodatuskalvojen toimivuuden arviointi paperiteollisuuden sovelluksissa

Työn tavoitteena oli etsiä vaihtoehtoja paperiteollisuuden kiertovesien ja pastapitoisten jätevesien suodatusprosesseissa tällä hetkellä käytössä oleville kalvoille. Työssä pyrittiin myös määrittämään tekijöitä, joiden avulla voitaisiin ennustaa polymeerikalvon käyttäytymistä erilaisissa paperiteollisuuden kalvosovelluksissa. Työn kirjallisessa osassa tarkasteltiin polymeerikalvojen ominaisuuksia, jotka vaikuttavat kalvojen käyttäytymiseen suodatusprosesseissa. Työssä esiteltiin myös tavallisimmat kalvomateriaalit ja polymeerikalvojen valmistustavat sekä paperiteollisuuden kalvosovelluksia. Paperiteollisuuden kalvosuodatussovellukset eroavat toisistaan huomattavasti toimintaolosuhteiltaan ja käyttötarkoituksiltaan. Tästä johtuen on hankalaa löytää yhteisiä tekijöitä, joiden perusteella voitaisiin ennustaa kalvon käyttäytymistä eri sovelluksissa. Kalvon hydrofiilisyyden todettiin kuitenkin vaikuttavan positiivisesti suodatustapahtumaan useissa sovelluksissa. Kokeellisessa osassa verrattiin erilaisten polymeerikalvojen ja referenssikalvojen toimintaa happaman kirkkaan suodoksen ja pastapitoisen veden suodatuksessa. Kirkkaan suodoksen suodatuskokeet tehtiin UPM-Kymmene Oy:n Kaukaan tehtailla. Pastapitoista jätevettä mallinnettiin syöttöpanoksilla, jotka tehtiin laimentamalla CTC:n valmistamaa LWC-pastaa. Suodatukset tehtiin CR 200/1- ja CR 550/10 -suodattimilla. Kirkkaan suodoksen suodatuksissa käytettiin referenssikalvona regeneroidusta selluloosasta ja pastapitoisen veden suodatuksessa aromaattisesta polyamidista valmistettua kalvoa. Kirkkaan suodoksen koesuodatusten perusteella todettiin, ettei minkään vertailtavan ultrasuodatuskalvon suodatuskapasiteetti ollut yhtä korkea kuin referenssikalvon. Referenssikalvon toiminta suodatuksessa oli myös vakaata syötön laadun muutoksista huolimatta. Todennäköisesti referenssikalvon erittäin hydrofiilinen luonne tekee siitä vertailtavia kalvoja sopivamman kirkkaan suodoksen suodatukseen. Pastapitoisen veden suodatustulosten perusteella referenssikalvolle löytyi useita potentiaalisia korvaajia. Näistä parhaan kalvon valitseminen edellyttää kuitenkin jatkotutkimuksia. SEM-analyysituloksista huomattiin, että tietyntyyppinen kalvorakenne parantaa kalvon toimintaa pastapitoisen veden suodatuksessa.

The impact of bioavailability limitations on microbial stable isotope fractionation in a multiphase system

Stable isotope fractionation analysis of contaminants is a promising method for assessing biodegradation of contaminants in natural systems. However, standard procedures to determine stable isotope fractionation factors, so far, neglect the influence of pollutant bioavailability on stable isotope fractionation. On a microscale, bioavailability may vary due to the spatio-temporal variability of local contaminant concentrations, limited effective diffusivities of the contaminants and cell densities, and thus, the pollutant supply might not meet the intrinsic degradation capacity of the microorganisms. The aim of this study was to demonstrate the effect of bioavailability on the apparent stable isotope fractionation, using a multiphase laboratory setup. The data gained show that the apparent isotope fractionation factors observed during biodegradation processes depend on the amount of biomass and/or the rate of toluene mass transfer from a second to the aqueous phase. They indicate that physico-chemical processes need to be taken into account when stable isotope fractionation analysis is used for the quantification of environmental contaminant degradation.

Fractionation of wood hydrolysate by ultrafiltration membranes at high temperature

Ultrafiltration (UF) is already used in pulp and paper industry and its demand is growing because of the required reduction of raw water intake and the separation of useful compounds from process waters. In the pulp and paper industry membranes might be exposed to extreme conditions and, therefore, it is important that the membrane can withstand them. In this study, extractives, hemicelluloses and lignin type compounds were separated from wood hydrolysate in order to be able to utilise the hemicelluloses in the production of biofuel. The performance of different polymeric membranes at different temperatures was studied. Samples were analysed for total organic compounds (TOC), lignin compounds (UV absorption at 280 nm) and sugar. Turbidity, conductivity and pH were also measured. The degree of fouling of the membranes was monitored by measuring the pure water flux before and comparing it with the pure water flux after the filtration of hydrolysate. According to the results, the retention of turbidity was observed to be higher at lower temperature compared to when the filtrations were operated at high temperature (70 °C). Permeate flux increased with elevated process temperature. There was no detrimental effect of temperature on most of the membranes used. Microdyn-Nadir regenerated cellulose membranes (RC) and GE-Osmonics thin film membranes seemed to be applicable in the chosen process conditions. The Polyethersulphone (NF-PES-10 and UH004P) and polysulphone (MPS-36) membranes used were highly fouled, but they showed high retentions for different compounds.

Building the map of innovation for membrane materials (Ceramic membranes)

This work proposes a method of visualizing the trend of research in the field of ceramic membranes from 1999 to 2006. The presented approach involves identifying problems encountered during research in the field of ceramic membranes. Patents from US patent database and articles from Science Direct(& by ELSEVIER was analyzed for this work. The identification of problems was achieved with software Knowledgist which focuses on the semantic nature of a sentence to generate series of subject action object structures. The identified problems are classified into major research issues. This classification was used for the visualization of the intensity of research. The image produced gives the relation between the number of patents, with time and the major research issues. The identification of the most cited papers which strongly influence the research of the previously identified major issues in the given field was also carried out. The relations between these papers are presented using the metaphor of social network. The final result of this work are two figures, a diagram showing the change in the studied problems a specified period of time and a figure showing the relations between the major papers and groups of the problems

Preparation of Polysulfone Membranes

As it is known, a huge part of all commercially available membranes are prepared by immersion precipitation. This way is the primary way to get flat membranes. The advantages of immersion precipitation are: wide field of the polymers, which can be used (polymer must be soluble in a solvent or a solvent mixture) and ease of performing. The literature part of this work deals with phase inversion membrane preparation methods and casting parameters affecting membrane performance. Also some membrane types and materials are discussed. In the experimental part of this work 73 membrane samples were made with different casting parameters (polymer concentration in the casting solution and precipitation time) and tested for the retention and permeability. The results of these experiments are collected and combined into the figures and tables which are presented in this thesis. This work showed and confirmed connection between membrane performance and casting parameters (concentration of polymer in the casting solution and precipitation time).

Bön om ro

Soitinnus: piano.

Bön om ro, op 122, nro 6

Soitinnus: laulu, ork.

Du är min ro

Soitinnus: lauluääni, piano.

Electroactive ion exchange membranes based on conducting polymers

Ion exchange membranes are indispensable for the separation of ionic species. They can discriminate between anions and cations depending on the type of fixed ionic group present in the membrane. These conventional ion exchange membranes (CIX) have exceptional ionic conductivity, which is advantageous in various electromembrane separation processes such as electrodialysis, electrodeionisation and electrochemical ion exchange. The main disadvantage of CIX membranes is their high electrical resistance owing to the fact that the membranes are electronically non conductive. An alternative can be electroactive ion exchange membranes, which are ionically and electronically conducting. Polypyrrole (PPy) is a type of electroactive ion exchange material as well as a commonly known conducting polymer. When PPy membranes are repeatedly reduced and oxidised, ions are pumped through the membrane. The main aim of this thesis was to develop electroactive cation transport membranes based on PPy for the selective transport of divalent cations. Membranes developed composed of PPy films deposited on commercially available support materials. To carry out this study, cation exchange membranes based on PPy doped with immobile anions were prepared. Two types of dopant anions known to interact with divalent metal ions were considered, namely 4-sulphonic calix[6]arene (C6S) and carboxylated multiwalled carbon nanotubes (CNT). The transport of ions across membranes containing PPy doped with polystyrene sulphonate (PSS) and PPy doped with para-toluene sulphonate (pTS) was also studied in order to understand the nature of ion transport and permeability across PPy(CNT) and PPy(C6S) membranes. In the course of these studies, membrane characterisation was performed using electrochemical quartz crystal microbalance (EQCM) and scanning electron microscopy (SEM). Permeability of the membranes towards divalent cations was explored using a two compartment transport cell. EQCM results demonstrated that the ion exchange behaviour of polypyrrole is dependent on a number of factors including the type of dopant anion present, the type of ions present in the surrounding medium, the scan rate used during the experiment and the previous history of the polymer film. The morphology of PPy films was found to change when the dopant anion was varied and even when the thickness of the film was altered in some cases. In nearly all cases the permeability of the membranes towards metal ions followed the order K+ > Ca2+ > Mn2+. The one exception was PPy(C6S), for which the permeability followed the order Ca2+ ≥ K+ > Mn2+ > Co2+ > Cr3+. The above permeability sequences show a strong dependence on the size of the metal ions with metal ions having the smallest hydrated radii exhibiting the highest flux. Another factor that affected the permeability towards metal ions was the thickness of the PPy films. Films with the least thickness showed higher metal ion fluxes. Electrochemical control over ion transport across PPy(CNT) membrane was obtained when films composed of the latter were deposited on track-etched Nucleopore® membranes as support material. In contrast, the flux of ions across the same film was concentration gradient dependent when the polymer was deposited on polyvinylidene difluoride membranes as support material. However, electrochemical control over metal ion transport was achieved with a bilayer type of PPy film consisting of PPy(pTS)/PPy(CNT), irrespective of the type of support material. In the course of studying macroscopic charge balance during transport experiments performed using a two compartment transport cell, it was observed that PPy films were non-permselective. A clear correlation between the change in pH in the receiving solution and the ions transported across the membrane was observed. A decrease in solution pH was detected when the polymer membrane acted primarily as an anion exchanger, while an increase in pH occurred when it functioned as a cation exchanger. When there was an approximately equal flux of anions and cations across the polymer membrane, the pH in the receiving solution was in the range 6 - 8. These observations suggest that macroscopic charge balance during the transport of cations and anions across polypyrrole membranes was maintained by introduction of anions (OH-) and cations (H+) produced via electrolysis of water.