Northern agriculture : constraints and responses to global climate change

Selostus: Maatalous pohjoisilla äärialueilla: ilmastolliset rajoitukset ja ilmaston muutosten vaikutukset viljelyyn

Change detection in boreal forests using bi-temporal aerial photographs

[Abstract]

Temporal trends in chemical parameters of upland forest soils in southern Finland

Abstract

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Active sulphide mine tailings impoundments as sources of contaminated drainage: controlling factors, methods of characterisation and geochemical constraints for mitigation

Low quality mine drainage from tailings facilities persists as one of the most significant global environmental concerns related to sulphide mining. Due to the large variation in geological and environmental conditions at mine sites, universal approaches to the management of mine drainage are not always applicable. Instead, site-specific knowledge of the geochemical behaviour of waste materials is required for the design and closure of the facilities. In this thesis, tailings-derived water contamination and factors causing the pollution were investigated in two coeval active sulphide mine sites in Finland: the Hitura Ni mine and the Luikonlahti Cu-Zn-Co-Ni mine and talc processing plant. A hydrogeochemical study was performed to characterise the tailingsderived water pollution at Hitura. Geochemical changes in the Hitura tailings were evaluated with a detailed mineralogical and geochemical investigation (solid-phase speciation, acid mine drainage potential, pore water chemistry) and using a spatial assessment to identify the mechanisms of water contamination. A similar spatial investigation, applying selective extractions, was carried out in the Luikonlahti tailings area for comparative purposes (Hitura low-sulphide tailings vs. Luikonlahti sulphide-rich tailings). At both sites, hydrogeochemistry of tailings seepage waters was further characterised to examine the net results of the processes observed within the impoundments and to identify constraints for water treatment. At Luikonlahti, annual and seasonal variation in effluent quality was evaluated based on a four-year monitoring period. Observations pertinent to future assessment and mine drainage prevention from existing and future tailings facilities were presented based on the results. A combination of hydrogeochemical approaches provided a means to delineate the tailings-derived neutral mine drainage at Hitura. Tailings effluents with elevated Ni, SO₄ ^2- and Fe content had dispersed to the surrounding aquifer through a levelled-out esker and underneath the seepage collection ditches. In future mines, this could be avoided with additional basal liners in tailings impoundments where the permeability of the underlying Quaternary deposits is inadequate, and with sufficiently deep ditches. Based on the studies, extensive sulphide oxidation with subsequent metal release may already initiate during active tailings disposal. The intensity and onset of oxidation depended on e.g. the Fe sulphide content of the tailings, water saturation level, and time of exposure of fresh sulphide grains. Continuous disposal decreased sulphide weathering in the surface of low-sulphide tailings, but oxidation initiated if they were left uncovered after disposal ceased. In the sulphide-rich tailings, delayed burial of the unsaturated tailings had resulted in thick oxidized layers, despite the continuous operation. Sulphide weathering and contaminant release occurred also in the border zones. Based on the results, the prevention of sulphide oxidation should already be considered in the planning of tailings disposal, taking into account the border zones. Moreover, even lowsulphide tailings should be covered without delay after active disposal ceases. The quality of tailings effluents showed wide variation within a single impoundment and between the two different types of tailings facilities assessed. The affecting factors included source materials, the intensity of weathering of tailings and embankment materials along the seepage flow path, inputs from the process waters, the water retention time in tailings, and climatic seasonality. In addition, modifications to the tailings impoundment may markedly change the effluent quality. The wide variation in the tailings effluent quality poses challenges for treatment design. The final decision on water management requires quantification of the spatial and seasonal fluctuation at the site, taking into account changes resulting from the eventual closure of the impoundment. Overall, comprehensive hydrogeochemical mapping was deemed essential in the identification of critical contaminants and their sources at mine sites. Mineralogical analysis, selective extractions, and pore water analysis were a good combination of methods for studying the weathering of tailings and in evaluating metal mobility from the facilities. Selective extractions with visual observations and pH measurements of tailings solids were, nevertheless, adequate in describing the spatial distribution of sulphide oxidation in tailings impoundments. Seepage water chemistry provided additional data on geochemical processes in tailings and was necessary for defining constraints for water treatment.

Capital Structure of Finnish SMEs and Financial Constraints

This thesis studies capital structure of Finnish small and medium sized enterprises. The specific object of the study is to test whether financial constraints have an effect on capital structure. In addition influences of several other factors were studied. Capital structure determinants are formulated based on three capital structure theories. The tradeoff theory and the agency theory concentrate on the search of optimal capital structure. The pecking order theory concerns favouring on financing source over another. The data of this study consists of financial statement data and results of corporate questionnaire. Regression analysis was used to find out the effects of several determinants. Regression models were formed based on the presented theories. Short and long term debt ratios were considered separately. The metrics of financially constrained firms was included in all models. It was found that financial constrains have a negative and significant effect to short term debt ratios. The effect was negative also to long term debt ratio but not statistically significant. Other considerable factors that influenced debt ratios were fixed assets, age, profitability, single owner and sufficiency of internal financing.

Generalized Differential Evolution for Global Multi-Objective Optimization with Constraints

The objective of this thesis work is to develop and study the Differential Evolution Algorithm for multi-objective optimization with constraints. Differential Evolution is an evolutionary algorithm that has gained in popularity because of its simplicity and good observed performance. Multi-objective evolutionary algorithms have become popular since they are able to produce a set of compromise solutions during the search process to approximate the Pareto-optimal front. The starting point for this thesis was an idea how Differential Evolution, with simple changes, could be extended for optimization with multiple constraints and objectives. This approach is implemented, experimentally studied, and further developed in the work. Development and study concentrates on the multi-objective optimization aspect. The main outcomes of the work are versions of a method called Generalized Differential Evolution. The versions aim to improve the performance of the method in multi-objective optimization. A diversity preservation technique that is effective and efficient compared to previous diversity preservation techniques is developed. The thesis also studies the influence of control parameters of Differential Evolution in multi-objective optimization. Proposals for initial control parameter value selection are given. Overall, the work contributes to the diversity preservation of solutions in multi-objective optimization.

Opportunities, constraints and constrained opportunities – A study on mothers’ working time patterns in 22 European countries

The aim of this study was to analyse mothers’ working time patterns across 22 European countries. The focus was on three questions: how much mothers prefer to work, how much they actually work, and to what degree their preferred and actual working times are (in)consistent with each other. The focus was on cross-national differences in mothers’ working time patterns, comparison of mothers’ working times to that of childless women and fathers, as well as on individual- and country-level factors that explain the variation between them. In the theoretical background, the departure point was an integrative theoretical approach where the assumption is that there are various kinds of explanations for the differences in mothers’ working time patterns – namely structural, cultural and institutional – , and that these factors are laid in two levels: individual- and country-levels. Data were extracted from the European Social Survey (ESS) 2010 / 2011. The results showed that mothers’ working time patterns, both preferred and actual working times, varied across European countries. Four clusters were formed to illustrate the differences. In the full-time pattern, full-time work was the most important form of work, leaving all other working time forms marginal. The full-time pattern was perceived in terms of preferred working times in Bulgaria and Portugal. In polarised pattern countries, fulltime work was also important, but it was accompanied by a large share of mothers not working at all. In the case of preferred working times, many Eastern and Southern European countries followed it whereas in terms of actual working times it included all Eastern and Southern European countries as well as Finland. The combination pattern was characterised by the importance of long part-time hours and full-time work. It was the preferred working time pattern in the Nordic countries, France, Slovenia, and Spain, but Belgium, Denmark, France, Norway, and Sweden followed it in terms of actual working times. The fourth cluster that described mothers’ working times was called the part-time pattern, and it was illustrated by the prevalence of short and long part-time work. In the case of preferred working times, it was followed in Belgium, Germany, Ireland, the Netherlands and Switzerland. Besides Belgium, the part-time pattern was followed in the same countries in terms of actual working times. The consistency between preferred and actual working times was rather strong in a majority of countries. However, six countries fell under different working time patterns when preferred and actual working times were compared. Comparison of working mothers’, childless women’s, and fathers’ working times showed that differences between these groups were surprisingly small. It was only in part-time pattern countries that working mothers worked significantly shorter hours than working childless women and fathers. Results therefore revealed that when mothers’ working times are under study, an important question regarding the population examined is whether it consists of all mothers or only working mothers. Results moreover supported the use of the integrative theoretical approach when studying mothers’ working time patterns. Results indicate that mothers’ working time patterns in all countries are shaped by various opportunities and constraints, which are comprised of structural, cultural, institutional, and individual-level factors.

Spatial and temporal variation in fish populations and assemblages in coastal waters of the northern Baltic Proper

The distribution and traits of fish are of interest both ecologically and socio-economically. In this thesis, phenotypic and structural variation in fish populations and assemblages was studied on multiple spatial and temporal scales in shallow coastal areas in the archipelago of the northern Baltic Proper. In Lumparn basin in Åland Islands, the fish assemblage displayed significant seasonal variation in depth zone distribution. The results indicate that investigating both spatial and temporal variation in small scale is crucial for understanding patterns in fish distribution and community structure in large scale. The local population of Eurasian perch Perca fluviatilis L displayed habitat-specific morphological and dietary variation. Perch in the pelagic zone were on average deeper in their body shape than the littoral ones and fed on fish and benthic invertebrates. The results differ from previous studies conducted in freshwater habitats, where the pelagic perch typically are streamlined in body shape and zooplanktivorous. Stable isotopes of carbon and nitrogen differed between perch with different stomach contents, suggesting differentiation of individual diet preferences. In the study areas Lumparn and Ivarskärsfjärden in Åland Islands and Galtfjärden in Swedish east coast, the development in fish assemblages during the 2000’s indicated a general shift towards higher abundances of small-bodied lower-order consumers, especially cyprinids. For European pikeperch Sander lucioperca L., recent declines in adult fish abundances and high mortalities (Z = 1.06–1.16) were observed, which suggests unsustainably high fishing pressure on pikeperch. Based on the results it can be hypothesized that fishing has reduced the abundances of large predatory fish, which together with bottom-up forcing by eutrophication has allowed the lower-order consumer species to increase in abundances. This thesis contributes to the scientific understanding of aquatic ecosystems with new descriptions on morphological and dietary adaptations in perch in brackish water, and on the seasonal variation in small-scale spatial fish distribution. The results also demonstrate anthropogenic effects on coastal fish communities and underline the urgency of further reducing nutrient inputs and regulating fisheries in the Baltic Sea region.

International Entrepreneurship in Bottom of the Pyramid Markets – Overcoming institutional constraints

Bottom of the pyramid (BoP) markets are an underserved market of approximately four billion people living on under $5 a day in four regional areas: Africa, Asia, Eastern Europe and Latin America. According to estimations, the BoP market forms a $5 trillion global consumer market. Despite the potential of BoP markets, companies have traditionally focused on serving the markets of developed countries and ignored the large customer group at the bottom of the pyramid. The BoP approach as first developed by Prahalad and Hart in 2002 has focused on multinational corporations (MNCs), which were thought of as the ones who should take responsibility in serving the customers at the bottom of the pyramid. This study challenges this proposition and gives evidence that also smaller international new ventures – entrepreneurial firms that are international from their birth, can be successful in BoP markets. BoP markets are characterized by a number of deficiencies in the institutional environment such as strong reliance on informal sector, lack of infrastructure and lack of skilled labor. The purpose of this study is to increase the understanding of international entrepreneurship in BoP markets by analyzing how international new ventures overcome institutional constraints in BoP markets and how institutional uncertainty can be exploited by solving institutional problems. The main objective is divided into four sub objectives. • To describe the opportunities and challenges BoP markets present • To analyze the internationalization of INVs to BoP markets • To examine what kinds of strategies international entrepreneurs use to overcome institutional constraints • To explore the opportunities institutional uncertainty offers for INVs Qualitative approach was used to conduct this study and multiple-case study was chosen as a research strategy in order to allow cross-case analysis. The empirical data was collected through four interviews with the companies Fuzu, Mifuko, Palmroth Consulting and Sibesonke. The results indicated that understanding of the wider institutional environment improves the survival prospects of INVs in BoP markets and that it is indeed possible to exploit institutional uncertainty by solving institutional problems. The main findings were that first-hand experience of the markets and grassroots levels of information are the best assets in internationalization to BoP markets. This study highlights that international entrepreneurs with limited resources can improve the lives of people at the BoP with their business operations and act as small-scale institutional entrepreneurs contributing to the development of the institutional environment of BoP markets.