Magnesium hydroxide-based peroxide bleaching of high-brightness mechanical pulps

A high final brightness is desired in most paper and board products. This requires bleaching processes that are able to produce high-brightness pulps. Mechanical pulps are widely bleached for high brightness using alkaline hydrogen peroxide with traditional sodium hydroxide and sodium silicate as additives. With high doses however, peroxide bleaching causes high organic loads in the mill effluent and anionic trash carry-over to papermaking. To alleviate the problems that arise from the use of sodium-based additives in peroxide bleaching, interest in the use of alternative magnesium-based chemicals has increased. In this study, a new, technical high-purity magnesium hydroxide-based bleaching additive was evaluated on laboratory-scale, pilot-scale and mill-scale experiments and trials for its ability to produce a high brightness in peroxide bleaching without the known problems of sodium-based chemicals. The key findings of this study include: a high brightening potential of peroxide bleaching using the Mg(OH)2-based additive, significant reductions (40-70%) in all categories of environmental load, and cationic demand lowered by 60-70% in bleached pulp with no loss in strength properties or in sheet bulk. When used in TMP refiner bleaching, the Mg(OH)2-based additive resulted in savings in specific energy consumption and provided a good bleaching response.

Lightweight, liquid-cooled, direct-drive generator for highpower wind turbines: motivation, concept, and performance

Thesis: A liquid-cooled, direct-drive, permanent-magnet, synchronous generator with helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit offers an excellent combination of attributes to reliably provide economic wind power for the coming generation of wind turbines with power ratings between 5 and 20MW. A generator based on the liquid-cooled architecture proposed here will be reliable and cost effective. Its smaller size and mass will reduce build, transport, and installation costs. Summary: Converting wind energy into electricity and transmitting it to an electrical power grid to supply consumers is a relatively new and rapidly developing method of electricity generation. In the most recent decade, the increase in wind energy’s share of overall energy production has been remarkable. Thousands of land-based and offshore wind turbines have been commissioned around the globe, and thousands more are being planned. The technologies have evolved rapidly and are continuing to evolve, and wind turbine sizes and power ratings are continually increasing. Many of the newer wind turbine designs feature drivetrains based on Direct-Drive, Permanent-Magnet, Synchronous Generators (DD-PMSGs). Being low-speed high-torque machines, the diameters of air-cooled DD-PMSGs become very large to generate higher levels of power. The largest direct-drive wind turbine generator in operation today, rated just below 8MW, is 12m in diameter and approximately 220 tonne. To generate higher powers, traditional DD-PMSGs would need to become extraordinarily large. A 15MW air-cooled direct-drive generator would be of colossal size and tremendous mass and no longer economically viable. One alternative to increasing diameter is instead to increase torque density. In a permanent magnet machine, this is best done by increasing the linear current density of the stator windings. However, greater linear current density results in more Joule heating, and the additional heat cannot be removed practically using a traditional air-cooling approach. Direct liquid cooling is more effective, and when applied directly to the stator windings, higher linear current densities can be sustained leading to substantial increases in torque density. The higher torque density, in turn, makes possible significant reductions in DD-PMSG size. Over the past five years, a multidisciplinary team of researchers has applied a holistic approach to explore the application of liquid cooling to permanent-magnet wind turbine generator design. The approach has considered wind energy markets and the economics of wind power, system reliability, electromagnetic behaviors and design, thermal design and performance, mechanical architecture and behaviors, and the performance modeling of installed wind turbines. This dissertation is based on seven publications that chronicle the work. The primary outcomes are the proposal of a novel generator architecture, a multidisciplinary set of analyses to predict the behaviors, and experimentation to demonstrate some of the key principles and validate the analyses. The proposed generator concept is a direct-drive, surface-magnet, synchronous generator with fractional-slot, duplex-helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit to accommodate liquid coolant flow. The novel liquid-cooling architecture is referred to as LC DD-PMSG. The first of the seven publications summarized in this dissertation discusses the technological and economic benefits and limitations of DD-PMSGs as applied to wind energy. The second publication addresses the long-term reliability of the proposed LC DD-PMSG design. Publication 3 examines the machine’s electromagnetic design, and Publication 4 introduces an optimization tool developed to quickly define basic machine parameters. The static and harmonic behaviors of the stator and rotor wheel structures are the subject of Publication 5. And finally, Publications 6 and 7 examine steady-state and transient thermal behaviors. There have been a number of ancillary concrete outcomes associated with the work including the following. X Intellectual Property (IP) for direct liquid cooling of stator windings via an embedded coaxial coolant conduit, IP for a lightweight wheel structure for lowspeed, high-torque electrical machinery, and IP for numerous other details of the LC DD-PMSG design X Analytical demonstrations of the equivalent reliability of the LC DD-PMSG; validated electromagnetic, thermal, structural, and dynamic prediction models; and an analytical demonstration of the superior partial load efficiency and annual energy output of an LC DD-PMSG design X A set of LC DD-PMSG design guidelines and an analytical tool to establish optimal geometries quickly and early on X Proposed 8 MW LC DD-PMSG concepts for both inner and outer rotor configurations Furthermore, three technologies introduced could be relevant across a broader spectrum of applications. 1) The cost optimization methodology developed as part of this work could be further improved to produce a simple tool to establish base geometries for various electromagnetic machine types. 2) The layered sheet-steel element construction technology used for the LC DD-PMSG stator and rotor wheel structures has potential for a wide range of applications. And finally, 3) the direct liquid-cooling technology could be beneficial in higher speed electromotive applications such as vehicular electric drives.

Potential for Greenhouse Gas Emission Reductions by Using Biomethane as a Road Transportation Fuel

The aim of this thesis is to study whether the use of biomethane as a transportation fuel is reasonable from climate change perspective. In order to identify potentials and challenges for the reduction of greenhouse gas (GHG) emissions, this dissertation focuses on GHG emission comparisons, on feasibility studies and on the effects of various calculation methodologies. The GHG emissions calculations are carried out by using life cycle assessment (LCA) methodologies. The aim of these LCA studies is to figure out the key parameters affecting the GHG emission saving potential of biomethane production and use and to give recommendations related to methodological choices. The feasibility studies are also carried out from the life cycle perspective by dividing the biomethane production chain for various operators along the life cycle of biomethane in order to recognize economic bottlenecks. Biomethane use in the transportation sector leads to GHG emission reductions compared to fossil transportation fuels in most cases. In addition, electricity and heat production from landfill gas, biogas or biomethane leads to GHG reductions as well. Electricity production for electric vehicles is also a potential route to direct biogas or biomethane energy to transportation sector. However, various factors along the life cycle of biomethane affect the GHG reduction potentials. Furthermore, the methodological selections have significant effects on the results. From economic perspective, there are factors related to different operators along the life cycle of biomethane, which are not encouraging biomethane use in the transportation sector. To minimize the greenhouse gas emissions from the life cycle of biomethane, waste feedstock should be preferred. In addition, energy consumption, methane leakages, digestate utilization and the current use of feedstock or biogas are also key factors. To increase the use of biomethane in the transportation sector, political steering is needed to improve the feasibility for the operators. From methodological perspective, it is important to recognize the aim of the life cycle assessment study. The life cycle assessment studies can be divided into two categories: 1.) To produce average GHG information of biomethane to evaluate the acceptability of biomethane use compared to fossil transportation fuels. 2.) To produce GHG information of biomethane related to actual decision-making situations. This helps to figure out the actual GHG emission changes in cases when feedstock, biogas or biomethane are already in other use. For example directing biogas from electricity production to transportation use does not necessarily lead to additional GHG emission reductions. The use of biomethane seems to have a lot of potential for the reduction of greenhouse gas emissions as a transportation fuel. However, there are various aspects related to production processes, to the current use of feedstock or biogas and to the feasibility that have to be taken into account.

Cost efficient extractive removal of birch pulp

Tämän diplomityön tarkoituksena oli selvittää kustannustehokkaita keinoja uuteaineiden vähentämiseksi koivusulfaattimassasta. Uuteaineet voivat aiheuttaa ongelmia muodostaessaan saostumia prosessilaitteisiin. Saostumat aiheuttavat tukkeumia ja mittaushäiriöitä, mutta irrotessaan ne myös huonontavat sellun laatua. Lopputuotteeseen joutuessaan ne voivat lisäksi aiheuttaa haju- ja makuhaittoja, joilla on erityistä merkitystä esimerkiksi valmistettaessa elintarvikekartonkeja. Tämä työ tehtiin Stora Enson sellutehtaalla, Enocell Oy:llä, Uimaharjussa. Teoriaosassa käsiteltiin uuteaineiden koostumusta ja niiden aiheuttamia ongelmia sellu– ja paperitehtaissa. Lisäksi koottiin aikaisempien tehdaskokeiden fysikaalisia ja kemiallisia keinoja vähentää koivu-uutetta. Tarkastelualueina olivat puunkäsittely, keitto, pesemö ja valkaisu. Kokeellisessa osassa suoritettiin esikokeita laboratorio- ja tehdasmittakaavassa, jotta saavutettaisiin käytännöllistä tietoa itse lopuksi tehtävää tehdasmittakaavan koetta varten. Laboratoriokokeissa tutkittiin mm. keiton kappaluvun, lisäaineiden ja hartsisaippuan vaikutusta koivu-uutteeseen. Lisäksi suoritettiin myös happo- (A) ja peretikkahappovaiheen (Paa) laboratoriokokeet. Tehdasmittakaavassa tarkasteltiin mm. keiton kappaluvun, pesemön lämpötilan, A-vaiheen, valkaisun peroksidi- ja Paa-vaiheen vaikutusta koivu-uutteeseen. Uutteenpoistotehokkuutta eri menetelmien välillä vertailtiin niin määrällisesti kuin rahallisesti. Uutteenpoistotehokkuudella mitattuna vertailuvaihe oli tehokkain pesemön loppuvaiheessa ja valkaisun alkuvaiheessa. Pesemön loppuvaiheessa uutteenpoistoreduktiot olivat noin 30 % ja valkaisun alkuvaiheessa 40 %. Peroksidivaihe oli tehokkain käytettynä valkaisun loppuvaiheessa noin 40 % reduktiolla. Kustannustehokkuudella mitattuna tehokkaimmaksi osoittautui A-vaihe yhdessä peroksidivaiheen kanssa. Säästöt vertailujaksoon verrattuna olivat noin 0.3 €/ADt. Lisäksi kyseinen yhdistelmä osoittautui hyväksi keinoksi säilyttää uutetaso alle maksimirajan kuitulinja 2:lla, kun kuitulinjalla 1 tuotettiin samanaikaisesti armeeraussellua.

Puhdistetun jäteveden patogeenit ja desinfiointitarve

Turun seudulla kuuden kunnan jätevesien käsittely keskitetään Kakolanmäen kallion sisälle rakennettuun jätevedenpuhdistamoon, joka otetaan käyttöön vuoden 2008 lopulla. Kakolanmäen jätevedenpuhdistamolla on varauduttu tulevaisuudessa kiristyviin lupaehtoihin sekä mahdollisiin puhdistetun jäteveden hygieenistä laatua koskeviin lisämääräyksiin jättämällä tilavaraus puhdistetun jäteveden desinfioimiselle ultraviolettivalolla. Diplomityössä on selvitetty vuoden kestäneessä tutkimusjaksossa 1.9.2006- 31.8.2007 Turun kaupungin keskuspuhdistamolta mereen johdetun puhdistetun jäteveden ja esiselkeytetyn ohitusveden hygieenisen laadun vaihtelua. Jäteveden desinfiointitarvetta on arvioitu tarkastelemalla jätevedenpuhdistamon hygieenistä puhdistustulosta ja jätevesien vaikutusta purkuvesistön hygieeniseen tilaan. Tutkimuksen perusteella virtaama ei vaikuttanut merkittävästi jäteveden ulosteperäisten bakteerien määriin. Sen sijaan jäteveden bakteeripitoisuudet laskivat alhaisissa lämpötiloissa. Lämpötilan vaikutus näkyi selkeämmin esiselkeytetyssä kuin puhdistetussa jätevedessä eli bakteerien poistumiseen aktiivilietevaiheen aikana vaikuttavat muut tekijät. Mitä tehokkaammin aktiivilietevaihe toimi, sitä tehokkaammin myös bakteereja poistui. Taudinaiheuttajabakteerit selvisivät puhdistusprosessista paremmin viileän kauden aikana. Puhdistetun jäteveden hygieeninen laatu ei täyttänyt uimaveden tai kasteluveden laatuvaatimuksia, joten desinfiointitarve olisi perustelua. Jätevesien vaikutus Turun edustan merialueen hygieeniseen tilaan näkyi ajoittain korkeina bakteeripitoisuuksina purkupaikan lähistöllä. Vielä ei ole suoraa näyttöä siitä aiheuttavatko jätevedet purkupaikan lähistön uimarannoilla terveydellisiä riskejä. Jäteveden UV-desinfiointi kannattava toteuttaa vain jos hygieeninen puhdistusvelvoite määrätään. UV-desinfioinnin mitoituksessa Kakolanmäen jätevedenpuhdistamolla tulee ottaa huomioon suurin sallittu hydraulinen painehäviö. Mitoitus voidaan tehdä puhdistamon käyttöönoton jälkeen kun tarvitut prosessimittaustiedot ovat saatavilla.

Pientalon lämmitysjärjestelmän valinta

Lämmityskustannukset ovat merkittävä osa pientalon asumiskustannuksista. Oikealla lämmitysratkaisuvalinnalla voidaan saada merkittäviä säästöjä aikaiseksi. Lämmitysjärjestelmä on pitkäaikainen investointi ja järjestelmän vaihtaminen toiseen on usein kallista. Järjestelmän valinnassa tehtyä virhettä on siten vaikea korjata jälkikäteen. Jotta osataan valita kuhunkin tilanteeseen sopivin lämmitysratkaisu, täytyy tietää millaisia kustannuseriä eri vaihtoehdot sisältävät ja millainen merkitys niillä on kokonaiskustannuksiin. Lämmitysjärjestelmän valinnassa tulee huomioida asuntojen erilaiset energiantarpeet, tekniset ratkaisut ja käyttäjien mieltymykset. Edellä mainituista syistä lämmitysjärjestelmiä ei voida laittaa yleispätevään edullisuusjärjestykseen. Tässä työssä käsitellään esimerkkilaskelmien avulla joitain lämmitysjärjestelmäratkaisuja ja niiden kustannuksia. Vaikka työ ei käsitä kaikkia markkinoilla olevia vaihtoehtoja, työssä esitettyjä laskentamenetelmiä voidaan soveltaa myös muihin lämmitysjärjestelmiin.

Lämpöpumppujärjestelmät integroidussa kylmä- ja lämpötehon tuotossa

Tässä työssä tutkittiin lämpöpumppujärjestelmiä, joilla tuotetaan samaan aikaan kylmä- ja lämpötehoa. Höyryn puristus lämpöpumppu on yleisimmin käytetty lämpöpumpputyyppi ja sen pääkomponentit ovat kompressori, lauhdutin, paisuntaventtiili ja höyrystin. Lämpöpumppu tuottaa samaan aikaan kylmätehoa höyrystimellä ja lämpötehoa lauhduttimella. Lämpöpumpun toiminta-arvoihin vaikuttaa valittujen lämpötilatasojen lisäksi voimakkaasti valitun kiertoaineen termodynaamiset ominaisuudet sekä kompressorin painesuhteeseen verrannollinen isentrooppihyötysuhde. Uusissa lämpöpumpuissa käytetään HFC yhdisteitä sekä sekoituksia kiertoaineina, mutta myös luonnolliset aineet, kuten ammoniakki, ovat lupaavia korvikkeita CFC yhdisteille. Sopivia sovelluskohteita kylmä- ja lämpötehon yhteistuotannolle ovat kauppa- ja asuinrakennukset, hotellit, toimistot, elintarviketeollisuus ja -myymälät sekä vierekkäiset jää- ja uimahallit ja hiihtoputket. Kylmä- ja lämpötehon yhteistuotannolla voitaisiin saavuttaa merkittäviä säästöjä ja päästövähennyksiä. Esimerkiksi jäähallien kylmäkoneiden lauhdelämmön hyödyntämisessä olisi Suomessa potentiaalia 6-10 miljoonan euron vuotuisiin säästöihin. Kylmä- ja lämpötehon yhteistuotanto voidaan toteuttaa hyödyntämällä kylmäkoneen lauhdelämpöä toisella lämpöpumpulla. Toinen vaihtoehto on käyttää eri tilojen samanaikaiseen lämmittämiseen ja jäähdyttämiseen HPS lämpöpumppua tai moniyksikköistä lämpöpumppua.

Genetically Determined Hypometabolism in Alzheimer’s Disease and Midlife Risk Factors for Cognitive Impairment

The role of genetic factors in the pathogenesis of Alzheimer’s disease (AD) is not completely understood. In order to improve this understanding, the cerebral glucose metabolism of seven monozygotic and nine dizygotic twin pairs discordant for AD was compared to that of 13 unrelated controls using positron emission tomography (PET). Traditional region of interest analysis revealed no differences between the non-demented dizygotic co-twins and controls. In contrast, in voxel-level and automated region of interest analyses, the non-demented monozygotic co-twins displayed a lower metabolic rate in temporal and parietal cortices as well as in subcortical grey matter structures when compared to controls. Again, no reductions were seen in the non-demented dizygotic co-twins. The reductions seen in the non-demented monozygotic co-twins may indicate a higher genetically mediated risk of AD or genetically mediated hypometabolism possibly rendering them more vulnerable to AD pathogenesis. With no disease modifying treatment available for AD, prevention of dementia is of the utmost importance. A total of 2 165 at least 65 years old twins of the Finnish Twin Cohort with questionnaire data from 1981 participated in a validated telephone interview assessing cognitive function between 1999 and 2007. Those subjects reporting heavy alcohol drinking in 1981 had an elevated cognitive impairment risk over 20 years later compared to light drinkers. In addition, binge drinking was associated with an increased risk even when total alcohol consumption was controlled for, suggesting that binge drinking is an independent risk factor for cognitive impairment. When compared to light drinkers, also non-drinkers had an increased risk of cognitive impairment. Midlife hypertension, obesity and low leisure time physical activity but not hypercholesterolemia were significant risk factors for cognitive impairment. The accumulation of risk factors increased cognitive impairment risk in an additive manner. A previously postulated dementia risk score based on midlife demographic and cardiovascular factors was validated. The risk score was found to well predict cognitive impairment risk, and cognitive impairment risk increased significantly as the score became higher. However, the risk score is not accurate enough for use in the clinic without further testing.

Liikennebiokaasun tuotannon ja käytön ulkoiset kustannukset Pohjois-Karjalassa

Työn tavoitteena oli selvittää liikennebiokaasuntuotannon ja käytön vaikutus liikenteen ulkoi-siin kustannuksiin Pohjois-Karjalassa. Biokaasua tuotetaan Joensuussa Kuhasalon jäteveden-puhdistamolla sekä Kontiosuon jäteasemalla, Kiteellä biokaasua tuotetaan BioKympin yh-teismädätyslaitoksessa. Lisäksi laskennassa huomioitiin yhden maatilakokoluokan biokaasun-tuotanto. Työssä selvitettiin kaksi skenaariota liikennebiokaasun tuotantomääräksi vuodelle 2015. Liikennebiokaasua voitaisiin tuottaa optimiskenaarion mukaan 3 426 MWh ja maksimi-tuotantoskenaarion mukaan 21 532 MWh. Liikennebiokaasun käytön vaikutukset liikenteen päästöihin laskettiin vuodelle 2015 ja vuo-delle 2020, jolloin liikennebiokaasua käytettäisiin 10 % liikenteen energiantarpeesta Pohjois-Karjalassa. Hiilidioksidipäästöt vähenevät vuoden 2020 tilanteessa samassa suhteessa kuin liikennebiokaasu korvaa fossiilisia polttoaineita. Muista päästöistä merkittävimmät päästövä-hennykset saatiin kun vuoden 2010 dieselautot muutettaisiin biokaasuautoiksi, tällöin hiuk-kaspäästöt alenisivat jopa 18 % vuoden 2010 päästöistä. Lisäksi selvitettiin liikenteen päästöjen pienenemisen vaikutus liikenteen aiheuttamiin ulkoisiin kustannuksiin. Laskettavat ulkoiset kustannukset olivat ilmastonmuutos, pakokaasupäästöt sekä energiariippuvuus. Pakokaasupäästöjen aiheuttamat ulkoiset kustannukset olivat vuonna 2010 noin 7 miljoonaa euroa. Liikennebiokaasua käyttävästä ajoneuvotyypistä riippuen ulkoiset kustannukset laskevat vuoden 2020 tilanteessa 10–16 % vuoden 2010 kustannuksista. Ilmastonmuutoksen ulkoiset kustannukset vuodelle 2010 olivat 9,5 miljoonaa euroa. Biokaasun käytön avulla kustannuksissa voitaisiin säästää 910 000 euroa vuonna 2020. Ener-giariippuvuuden hinta öljynkäytöstä oli vuonna 2010 noin 4,2 miljoonaa euroa ja vuonna 2020 kustannukset voisivat laskea 450 000 euroa.

Adaptive Routing Approaches for Networked Many-Core Systems

Through advances in technology, System-on-Chip design is moving towards integrating tens to hundreds of intellectual property blocks into a single chip. In such a many-core system, on-chip communication becomes a performance bottleneck for high performance designs. Network-on-Chip (NoC) has emerged as a viable solution for the communication challenges in highly complex chips. The NoC architecture paradigm, based on a modular packet-switched mechanism, can address many of the on-chip communication challenges such as wiring complexity, communication latency, and bandwidth. Furthermore, the combined benefits of 3D IC and NoC schemes provide the possibility of designing a high performance system in a limited chip area. The major advantages of 3D NoCs are the considerable reductions in average latency and power consumption. There are several factors degrading the performance of NoCs. In this thesis, we investigate three main performance-limiting factors: network congestion, faults, and the lack of efficient multicast support. We address these issues by the means of routing algorithms. Congestion of data packets may lead to increased network latency and power consumption. Thus, we propose three different approaches for alleviating such congestion in the network. The first approach is based on measuring the congestion information in different regions of the network, distributing the information over the network, and utilizing this information when making a routing decision. The second approach employs a learning method to dynamically find the less congested routes according to the underlying traffic. The third approach is based on a fuzzy-logic technique to perform better routing decisions when traffic information of different routes is available. Faults affect performance significantly, as then packets should take longer paths in order to be routed around the faults, which in turn increases congestion around the faulty regions. We propose four methods to tolerate faults at the link and switch level by using only the shortest paths as long as such path exists. The unique characteristic among these methods is the toleration of faults while also maintaining the performance of NoCs. To the best of our knowledge, these algorithms are the first approaches to bypassing faults prior to reaching them while avoiding unnecessary misrouting of packets. Current implementations of multicast communication result in a significant performance loss for unicast traffic. This is due to the fact that the routing rules of multicast packets limit the adaptivity of unicast packets. We present an approach in which both unicast and multicast packets can be efficiently routed within the network. While suggesting a more efficient multicast support, the proposed approach does not affect the performance of unicast routing at all. In addition, in order to reduce the overall path length of multicast packets, we present several partitioning methods along with their analytical models for latency measurement. This approach is discussed in the context of 3D mesh networks.

A rose is a rose is a rose? Defining significant properties of social science research data

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Biogas production in regional integrated biodegradable waste treatment – Possibilities for improving energy performance and reducing GHG emissions

The greatest threat that the biodegradable waste causes on the environment is the methane produced in landfills by the decomposition of this waste. The Landfill Directive (1999/31/EC) aims to reduce the landfilling of biodegradable waste. In Finland, 31% of biodegradable municipal waste ended up into landfills in 2012. The pressure of reducing disposing into landfills is greatly increased by the forthcoming landfill ban on biodegradable waste in Finland. There is a need to discuss the need for increasing the utilization of biodegradable waste in regional renewable energy production to utilize the waste in a way that allows the best possibilities to reduce GHG emissions. The objectives of the thesis are: (1) to find important factors affecting renewable energy recovery possibilities from biodegradable waste, (2) to determine the main factors affecting the GHG balance of biogas production system and how to improve it and (3) to find ways to define energy performance of biogas production systems and what affects it. According to the thesis, the most important factors affecting the regional renewable energy possibilities from biodegradable waste are: the amount of available feedstock, properties of feedstock, selected utilization technologies, demand of energy and material products and the economic situation of utilizing the feedstocks. The biogas production by anaerobic digestion was seen as the main technology for utilizing biodegradable waste in agriculturally dense areas. The main reason for this is that manure was seen as the main feedstock, and it can be best utilized with anaerobic digestion, which can produce renewable energy while maintaining the spreading of nutrients on arable land. Biogas plants should be located close to the heat demand that would be enough to receive the produced heat also in the summer months and located close to the agricultural area where the digestate could be utilized. Another option for biogas use is to upgrade it to biomethane, which would require a location close to the natural gas grid. The most attractive masses for biogas production are municipal and industrial biodegradable waste because of gate fees the plant receives from them can provide over 80% of the income. On the other hand, directing gate fee masses for small-scale biogas plants could make dispersed biogas production more economical. In addition, the combustion of dry agricultural waste such as straw would provide a greater energy amount than utilizing them by anaerobic digestion. The complete energy performance assessment of biogas production system requires the use of more than one system boundary. These can then be used in calculating output–input ratios of biogas production, biogas plant, biogas utilization and biogas production system, which can be used to analyze different parts of the biogas production chain. At the moment, it is difficult to compare different biogas plants since there is a wide variation of definitions for energy performance of biogas production. A more consistent way of analyzing energy performance would allow comparing biogas plants with each other and other recovery systems and finding possible locations for further improvement. Both from the GHG emission balance and energy performance point of view, the energy consumption at the biogas plant was the most significant factor. Renewable energy use to fulfil the parasitic energy demand at the plant would be the most efficient way to reduce the GHG emissions at the plant. The GHG emission reductions could be increased by upgrading biogas to biomethane and displacing natural gas or petrol use in cars when compared to biogas CHP production. The emission reductions from displacing mineral fertilizers with digestate were seen less significant, and the greater N2O emissions from spreading digestate might surpass the emission reductions from displacing mineral fertilizers.

Pohjapaperin kustannusrakenteen optimointi

Kilpailulliset tekijät ovat johtaneet paperin valmistajat miettimään keinoja valmistuskustannusten leikkaamiseksi. Yksi keino on optimoida raaka-aineiden käyttöä, jota on tehty tässä diplomityössä. Työn tarkoitus on selvittää koeajoin mahdollisuudet kalliimpien raaka-aineiden korvaamiseen edullisemmilla, säilyttäen kuitenkin pohjapaperin laadulliset ominaisuudet. Työ on toteutettu UPM Kymmene Oyj:n Jokilaakson tehtailla, Jämsänkosken paperitehtaan Tarrapaperit-osastolla. Työssä on käytetty apuna tietokoneohjelmia mallintamaan ja simuloimaan paperissa ja paperin kustannusrakenteessa tapahtuvia muutoksia, mutta merkittävimmässä asemassa ovat olleet koeajot ja erilaisten näytteiden käsittely. Raaka-aineina käytettävien massojen osuuksien optimoinnilla on saatu aikaiseksi merkittäviä kustannussäästöjä, mutta työn yhteydessä on löydetty myös keinoja säästöjen saavuttamiseksi energiankulutusta järkevöittämällä. Luotu malli auttaa jatkossa kustannusrakenteen seurannassa. Mäntysellun osuuden laskulla ja täyteaineen osuuden nostolla saavutetaan merkittävimmät kustannussäästöt, kemihierteellä vaikutus kustannuksiin on vähäisempi. Sähköenergiaa vievä kuitujen jauhatus on järjestetty paperikone 3:lla uudella tavalla, jolla on paitsi saavutettu säästöä energiassa, parannettu myös paperin lujuutta.

The alpha2C-adrenoceptor as a neuropsychiatric drug tar-get - PET studies in human subjects

Positron emission tomography imaging has both academic and applied uses in revealing the distribution and density of different molecular targets in the central nervous system. Following the significant progress made with the dopamine D2 receptor, advances have been made in developing PET tracers to allow analysis of receptor occupancy of many other receptor types as well as evaluating changes in endogenous synaptic transmitter concentrations of transmitters e.g. serotonin and noradrenaline. Noradrenergic receptors are divided into α1-, α2- and β-adrenoceptor subfamilies, in humans each of which is composed of three receptor subtypes. The α2-adrenoceptors have an important presynaptic auto-inhibitory function on noradrenaline release but they also have postsynaptic roles in modulating the release of other neurotransmitters, such as serotonin and dopamine. One of the subtypes, the α2C-adrenoceptor, has been detected at distinct locations in the central nervous system, most notably the dorsal striatum. Several serious neurological conditions causing dementia, Alzheimer’s disease and Parkinson’s disease have been linked to disturbed noradrenergic signaling. Furthermore, altered noradrenergic signaling has also been implicated in conditions like ADHD, depression, anxiety and schizophrenia. In order to benefit future research into these central nervous system disorders as well as being useful in the clinical development of drugs affecting brain noradrenergic neurotransmission, validation work of a novel tracer for positron emission tomography studies in humans was performed. Altogether 85 PET imaging experiments were performed during four separate clinical trials. The repeatability of [11C]ORM-13070 binding was tested in healthy individuals, followed by a study to evaluate the dose-dependent displacement of [11C]ORM-13070 from α2C-adrenoceptors by a competing ligand, and the final two studies examined the sensitivity of [11C]ORM-13070 binding to reflect changes in endogenous noradrenaline levels. The repeatability of [11C]ORM-13070 binding was very high. The binding properties of the tracer allowed for a reliable estimation of α2C-AR occupancy by using the reference tissue ratio method with low test-retest variability. [11C]ORM-13070 was dose-dependently displaced from its specific binding sites by the subtype-nonselective α2-adrenoceptor antagonist atipamezole, and thus it proved suitable for use in clinical drug development of novel α2C-adrenoceptor ligands e.g. to determine the best doses and dosing intervals for clinical trials. Convincing experimental evidence was gained to support the suitability of [11C]ORM-13070 for detecting an increase in endogenous synaptic noradrenaline in the human brain. Tracer binding in the thalamus tended to increase in accordance with reduced activity of noradrenergic projections from the locus coeruleus, although statistical significance was not reached. Thus, the investigation was unable to fully validate [11C]ORM-13070 for the detection of pharmacologically evoked reductions in noradrenaline levels.