Development of Craniofacial Bone Defect Reconstruction Implant Based on Fibre-Reinforced Composite with Photopolymerisable Resin Systems. Experimental studies in vitro and in vivo.

Reconstruction of defects in the craniomaxillofacial (CMF) area has mainly been based on bone grafts or metallic fixing plates and screws. Particularly in the case of large calvarial and/or craniofacial defects caused by trauma, tumours or congenital malformations, there is a need for reliable reconstruction biomaterials, because bone grafts or metallic fixing systems do not completely fulfill the criteria for the best possible reconstruction methods in these complicated cases. In this series of studies, the usability of fibre-reinforced composite (FRC) was studied as a biostable, nonmetallic alternative material for reconstructing artificially created bone defects in frontal and calvarial areas of rabbits. The experimental part of this work describes the different stages of the product development process from the first in vitro tests with resin-impregnated fibrereinforced composites to the in vivo animal studies, in which this FRC was tested as an implant material for reconstructing different size bone defects in rabbit frontal and calvarial areas. In the first in vitro study, the FRC was polymerised in contact with bone or blood in the laboratory. The polymerised FRC samples were then incubated in water, which was analysed for residual monomer content by using high performance liquid chromatography (HPLC). It was found that this in vitro polymerisation in contact with bone and blood did not markedly increase the residual monomer leaching from the FRC. In the second in vitro study, different adhesive systems were tested in fixing the implant to bone surface. This was done to find an alternative implant fixing system to screws and pins. On the basis of this study, it was found that the surface of the calvarial bone needed both mechanical and chemical treatments before the resinimpregnated FRC could be properly fixed onto it. In three animal studies performed with rabbit frontal bone defects and critical size calvarial bone defect models, biological responses to the FRC implants were evaluated. On the basis of theseevaluations, it can be concluded that the FRC, based on E-glass (electrical glass) fibres forming a porous fibre veil enables the ingrowth of connective tissues to the inner structures of the material, as well as the bone formation and mineralization inside the fibre veil. Bone formation could be enhanced by using bioactive glass granules fixed to the FRC implants. FRC-implanted bone defects healed partly; no total healing of defects was achieved. Biological responses during the follow-up time, at a maximum of 12 weeks, to resin-impregnated composite implant seemed to depend on the polymerization time of the resin matrix of the FRC. Both of the studied resin systems used in the FRC were photopolymerised and the heat-induced postpolymerisation was used additionally.

Using time and stochastic models for software reliability forecasting and analysis

Tämä työ luo katsauksen ajallisiin ja stokastisiin ohjelmien luotettavuus malleihin sekä tutkii muutamia malleja käytännössä. Työn teoriaosuus sisältää ohjelmien luotettavuuden kuvauksessa ja arvioinnissa käytetyt keskeiset määritelmät ja metriikan sekä varsinaiset mallien kuvaukset. Työssä esitellään kaksi ohjelmien luotettavuusryhmää. Ensimmäinen ryhmä ovat riskiin perustuvat mallit. Toinen ryhmä käsittää virheiden ”kylvöön” ja merkitsevyyteen perustuvat mallit. Työn empiirinen osa sisältää kokeiden kuvaukset ja tulokset. Kokeet suoritettiin käyttämällä kolmea ensimmäiseen ryhmään kuuluvaa mallia: Jelinski-Moranda mallia, ensimmäistä geometrista mallia sekä yksinkertaista eksponenttimallia. Kokeiden tarkoituksena oli tutkia, kuinka syötetyn datan distribuutio vaikuttaa mallien toimivuuteen sekä kuinka herkkiä mallit ovat syötetyn datan määrän muutoksille. Jelinski-Moranda malli osoittautui herkimmäksi distribuutiolle konvergaatio-ongelmien vuoksi, ensimmäinen geometrinen malli herkimmäksi datan määrän muutoksille.

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination

Characterizing Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 as a new probiotic combination: basic properties of JS and pilot in vivo assessment of the combination Each candidate probiotic strain has to have the documentation for the proper identification with current molecular tools, for the biological properties, for the safety aspects and for the health benefits in human trials if the intention is to apply the strain as health promoting culture in the commercial applications. No generalization based on species properties of an existing probiotic are valid for any novel strain, as strain specific differences appear e.g. in the resistance to GI tract conditions and in health promoting benefits (Madsen, 2006). The strain evaluation based on individual strain specific probiotic characteristics is therefore the first key action for the selection of the new probiotic candidate. The ultimate goal in the selection of the probiotic strain is to provide adequate amounts of active, living cells for the application and to guarantee that the cells are physiologically strong enough to survive and be biologically active in the adverse environmental conditions in the product and in GI tract of the host. The in vivo intervention studies are expensive and time consuming; therefore it is not rational to test all the possible candidates in vivo. Thus, the proper in vitro studies are helping to eliminate strains which are unlikely to perform well in vivo. The aims of this study were to characterize the strains of Propionibacterium freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705, both used for decades as cheese starter cultures, for their technological and possible probiotic functionality applied in a combined culture. The in vitro studies of Propionibacterium freudenreichii ssp. shermanii JS focused on the monitoring of the viability rates during the acid and bile treatments and on the safety aspects such as antibiotic susceptibility and adhesion. The studies with the combination of the strains JS and LC705 administered in fruit juices monitored the survival of the strains JS and LC705 during the GI transit and their effect on gut wellbeing properties measured as relief of constipation. In addition, safety parameters such as side effects and some peripheral immune parameters were assessed. Separately, the combination of P. freudenreichii ssp. shermanii JS and Lactobacillus rhamnosus LC705 was evaluated from the technological point of view as a bioprotective culture in fermented foods and wheat bread applications. In this study, the role ofP. freudenreichii ssp. shermanii JS as a candidate probiotic culture alone and in a combination with L. rhamnosus LC705 was demonstrated. Both strains were transiently recovered in high numbers in fecal samples of healthy adults during the consumption period. The good survival through the GI transit was proven for both strains with a recovery rate from 70 to 80% for the JS strain and from 40 to 60% for the LC705 strain from the daily dose of 10 log10 CFU. The good survival was shown from the consumption of fruit juices which do not provide similar matrix protection for the cells as milk based products. The strain JS did not pose

Late effects of cancer at a young age: Registry-based studies of the health of cancer patients and their off-spring

Modern cancer therapy has resulted in increased survival among patients diagnosed with cancer at a young age. These improvements have led to the investigation of late morbidity and mortality associated with cancer and its treatments. The aim of this study was to evaluate late effects of cancer treated at a young age on the health of patients and their offspring. Utilising the nationwide population-based registries in Finland, we evaluated the risk of hypothyroidism and the probability of parenthood in cancer survivors as well as preterm birth, neonatal outcomes, and the risk of cancer among offspring of patients. The survivor cohort, identified from the Finnish Cancer Registry, consisted of 25,784 cancer patients diag-nosed between ages 0 and 34 in 1953–2004. By linkage to the population register, siblings of these patients were identified for comparison. The prevalence of hypothyroidism was higher among former childhood cancer (aged 0–16) patients than in the general population. The probability of parenthood following early onset cancer was overall significantly reduced compared to siblings. Offspring of female cancer survivors were at an increased risk of preterm birth, this risk being highest among patients diagnosed in childhood and early adulthood (aged 20–34 years). The offspring were not, however, at a significantly increased risk of neonatal death or stillbirth, though they were more likely to need monitoring or intensive care in the neonatal period. The risk of sporadic cancer among offspring of male and female cancer survivors was not elevated in comparison to the general population. The study showed that former cancer patients are at risk of certain adverse endocrine and reproductive health outcomes and should be followed for timely intervention. The offspring of cancer survivors do not appear to be at risk for adverse health outcomes.

Immediate Decision-Making and Information Needs in Intensive Care Coordination

The aim of this study was to develop a theoretical model for information integration to support the deci¬sion making of intensive care charge nurses, and physicians in charge – that is, ICU shift leaders. The study focused on the ad hoc decision-making and immediate information needs of shift leaders during the management of an intensive care unit’s (ICU) daily activities. The term ‘ad hoc decision-making’ was defined as critical judgements that are needed for a specific purpose at a precise moment with the goal of ensuring instant and adequate patient care and a fluent flow of ICU activities. Data collection and research analysis methods were tested in the identification of ICU shift leaders’ ad hoc decision-making. Decision-making of ICU charge nurses (n = 12) and physicians in charge (n = 8) was observed using a think-aloud technique in two university-affiliated Finnish ICUs for adults. The ad hoc decisions of ICU shift leaders were identified using an application of protocol analysis. In the next phase, a structured online question¬naire was developed to evaluate the immediate information needs of ICU shift leaders. A national survey was conducted in all Finnish, university-affiliated hospital ICUs for adults (n = 17). The questionnaire was sent to all charge nurses (n = 515) and physicians in charge (n = 223). Altogether, 257 charge nurses (50%) and 96 physicians in charge (43%) responded to the survey. The survey was also tested internationally in 16 Greek ICUs. From Greece, 50 charge nurses out of 240 (21%) responded to the survey. A think-aloud technique and protocol analysis were found to be applicable for the identification of the ad hoc decision-making of ICU shift leaders. During one day shift leaders made over 200 ad hoc decisions. Ad hoc decisions were made horizontally, related to the whole intensive care process, and vertically, concerning single intensive care incidents. Most of the ICU shift leaders’ ad hoc decisions were related to human resources and know-how, patient information and vital signs, and special treatments. Commonly, this ad hoc decision-making involved several multiprofessional decisions that constituted a bundle of immediate decisions and various information needs. Some of these immediate information needs were shared between the charge nurses and the physicians in charge. The majority of which concerned patient admission, the organisation and management of work, and staff allocation. In general, the information needs of charge nurses were more varied than those of physicians. It was found that many ad hoc deci-sions made by the physicians in charge produced several information needs for ICU charge nurses. This meant that before the task at hand was completed, various kinds of information was sought by the charge nurses to support the decision-making process. Most of the immediate information needs of charge nurses were related to the organisation and management of work and human resources, whereas the information needs of the physicians in charge mainly concerned direct patient care. Thus, information needs differ between professionals even if the goal of decision-making is the same. The results of the international survey confirmed these study results for charge nurses. Both in Finland and in Greece the information needs of charge nurses focused on the organisation and management of work and human resources. Many of the most crucial information needs of Finnish and Greek ICU charge nurses were common. In conclusion, it was found that ICU shift leaders make hundreds of ad hoc decisions during the course of a day related to the allocation of resources and organisation of patient care. The ad hoc decision-making of ICU shift leaders is a complex multi-professional process, which requires a lot of immediate information. Real-time support for information related to patient admission, the organisation and man¬agement of work, and allocation of staff resources is especially needed. The preliminary information integration model can be applied when real-time enterprise resource planning systems are developed for intensive care daily management

Metsäteollisuuden jätevesien häiriöpäästöt ja niihin varautuminen. CASE: Kaakkois-Suomi

Metsäteollisuuden jätevesien normaaleja jatkuvia päästöjä hallitaan yhä paremmin. Tästä syystä niin sanottujen häiriöpäästöjen merkitys vesien kuormittajana kasvaa. Työssä tarkasteltiin 14 Kaakkois-Suomen metsäteollisuuden toiminnanharjoittajan jätevesien häiriöpäästöjä.Työn tavoitteena oli selvittää minkälaisia ja kuinka paljon poikkeuksellisia tilanteita on viime vuosina esiintynyt. Työssä selvitettiin mitkä syyt olivat aiheuttaneet häiriöpäästöjä, mitä vaikutuksia häiriöillä oli jätevesipäästöihin sekä kuinka tilanteissa oli toimittu. Työn teoriaosassa tarkasteltiin metsäteollisuuden tuotantoprosessien ja jätevedenpuhdistuksen mahdollisia häiriöpäästölähteitä sekä niiden ominaispiirteitä. Lisäksi tarkasteltiin häiriöpäästöjen vaikutuksia ja seurauksia toiminnanharjoittajien ja lupaviranomaisten näkökulmasta sekä kuinka häiriöpäästöihin tulee lainsäädännön ja ympäristöjärjestelmien mukaan varautua. Tutkimusosio koostui toiminnanharjoittajille lähetetystä häiriöpäästökyselystä, viranomaisille lähetetyistä häiriöpäästöilmoituksista sekä VAHTI –tietokannan vesipäästötiedoista. Kaikilla toiminnanharjoittajilla esiintyi häiriöpäästöjä. Häiriöpäästöt aiheuttivat lupaehtojen ylityksiä vuosina 1998-2003 yhteensä 66 kappaletta. Suurimpana syynä häiriöpäästöihin olivat prosessihäiriöt. Useimmiten häiriöpäästöt olivat usean eri syyn summa. Häiriöpäästöjen ilmoittamiskäytäntö viranomaisille vaihtelee, vaikka lupaehdoissa häiriö- ja poikkeustilanteet on määritelty kaikille lähes samalla tavalla. Jotkut ilmoittavat kaikista päästölisäyksistä, kun taas toiset ainoastaan merkittävistä. Osa ilmoittaa häiriöpäästöistä puhelimitse, jolloin ilmoituksesta ei jää kirjallista dokumenttia. Kaikista lupaehtojen ylityksistä ei ole tehty kirjallista ilmoitusta. Lupaehdoissa on häiriö- ja poikkeustilanteet määritelty sen verran suppeasti, että toiminnanharjoittajat soveltavat niitä haluamallaan tavalla. Valvontaviranomaiset puuttuvat häiriötilanteisiin lähinnä kehottamalla toiminnanharjoittajia poistamaan häiriötilanteet. Viranomaiset eivät ole määränneet toiminnan keskeyttämistä häiriöpäästöjen poistamiseksi. Yhdestä häiriöpäästöstä on tehty rikosilmoitus.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.