Effect of Noncondensable Gases on Circulation of Primary Coolant in Nuclear Power Plants in Abnormal Situations

The present study focuses on two effects of the presence of a noncondensable gas on the thermal-hydraulic behavior of thecoolant of the primary circuit of a nuclear reactor in the VVER-440 geometry inabnormal situations. First, steam condensation with the presence of air was studied in the horizontal tubes of the steam generator (SG) of the PACTEL test facility. The French thermal-hydraulic CATHARE code was used to study the heat transfer between the primary and secondary side in conditions derived from preliminary experiments performed by VTT using PACTEL. In natural circulation and single-phase vapor conditions, the injection of a volume of air, equivalent to the totalvolume of the primary side of the SG at the entrance of the hot collector, did not stop the heat transfer from the primary to the secondary side. The calculated results indicate that air is located in the second half-length (from the mid-length of the tubes to the cold collector) in all the tubes of the steam generator The hot collector remained full of steam during the transient. Secondly, the potential release of the nitrogen gas dissolved in the water of the accumulators of the emergency core coolant system of the Loviisa nuclear power plant (NPP) was investigated. The author implemented a model of the dissolution and release ofnitrogen gas in the CATHARE code; the model created by the CATHARE developers. In collaboration with VTT, an analytical experiment was performed with some components of PACTEL to determine, in particular, the value of the release time constant of the nitrogen gas in the depressurization conditions representative of the small and intermediate break transients postulated for the Loviisa NPP. Such transients, with simplified operating procedures, were calculated using the modified CATHARE code for various values of the release time constant used in the dissolution and release model. For the small breaks, nitrogen gas is trapped in thecollectors of the SGs in rather large proportions. There, the levels oscillate until the actuation of the low-pressure injection pumps (LPIS) that refill the primary circuit. In the case of the intermediate breaks, most of the nitrogen gas is expelled at the break and almost no nitrogen gas is trapped in the SGs. In comparison with the cases calculated without taking into account the release of nitrogen gas, the start of the LPIS is delayed by between 1 and 1.75 h. Applicability of the obtained results to the real safety conditions must take into accountthe real operating procedures used in the nuclear power plant.

The Effect of Plant Closures on Market Value: Empirical Evidence from Pulp and Paper Industry 2004-2012

The aim of this study was to research how plant closure announcements affect the market value of the largest pulp and paper industry companies in the world. Also the effect of announcements on competitors was researched and whether the location of plants, timing, reasons for the closures, and characteristics of the closing firms and competitors have an impact on the results. The overall sample included 57 events in the years 2004-2012 and event study was used as a research method. Main theories were signaling theory and spillover effect. According to empirical results, investors consider plant closure announcements as a positive signal for market value. The spillover effect on competitors was, on average, positive and characteristics of the firms and closures had an effect on the results. Furthermore, the market generally predicted the closures and overreacted to them on the announcement day and after it. It is possible for corporate management and investors to learn from the results and use them as support for their decision making.

Effect of species composition on economic return in amixed stand of Norway spruce and Scots Pine

Summary

Effect of fertilizer treatment on the biomass production and nutrient uptake of short-rotation willow on cut-away peatlands

Summary

Effect of soil wetness on air composition and nitrous oxide emission in a loam soil

Selostus: Maan märkyyden vaikutus ilman koostumukseen ja dityppioksidiemissioon hiuemaassa

Effect of drainage maintenance on the nutrient status on drained Scots pine mires

Tiivistelmä: Kunnostusojituksen vaikutus rämeiden ravinnetilaan

Effect of harvest time on storage loss and sprouting in onion

Selostus: Sadonkorjuuajan vaikutus sipulin varastohävikkiin ja varastoinnin jälkeiseen versomiseen

Effect of anionic salts on some blood and urine minerals, acid-base balance and udder oedema of dry pregnant cows

Selostus: Anionisten suolojen vaikutus ummessa olevien lehmien veren ja virtsan kivennäisiin, happo-emästasapainoon sekä utarepöhöön

Effect of compression wood on surface roughness and surface absorption of medium density fiberboard

Abstract

The Effect of Family Ownership on Firm Performance: Empirical Evidence from Norway

Tutkimuksen tavoitteena on selvittää, onko perheomistajuus, eli yksityisomistus, kannattavampi omistusmuoto kuin institutionaalinen omistajuus ja, onko yrityksen iällä ja koolla vaikutusta perheyritysten menestymiseen. Aikaisempaan tutkimustietoon tukeutuen, tutkimuksen aluksi käydään myös läpi perheomistajuuteen yleisesti liitettyjä ominaispiirteitä sekä perheyritysten menestymistä verrattuna ei-perheyrityksiin. Empiirinen analyysi perheomistajuuden vaikutuksista yrityksen kannattavuuteen sekä yrityksen iän ja koon vaikutuksista perheyritysten menestymiseen toteutetaan kahden otoksen avulla, jotka koostuvat listaamattomista norjalaisista pienistä ja keskisuurista yrityksistä (pk-yrityksistä). Näin ollen satunnaisotos ja päätoimialaotos, johon listaamattomat pk-yritykset on valittu satunnaisesti Norjan tärkeimmiltä toimialoilta, analysoidaan erikseen. Analyysi toteutetaan käyttäen lineaarista regressioanalyysia. Vaikka satunnaisotoksen perusteella perheyritykset eivät näytä olevan ei-perheyrityksiä kannattavampia, päätoimialaotos osoittaa, että listaamattomissa pk-yrityksissä perhe- eli yksityisomistajuus on merkittävästi institutionaalista omistajuutta kannattavampi omistusmuoto. Eritoten nuoret ja pienet yritykset vastaavat perheyritysten paremmasta kannattavuudesta.

The effect of brand trust on satisfaction, trust, and loyalty on a consumer magazine website

Internetin käyttö on yleistynyt valtavasti viimeisen kymmenen vuoden aikana. Internetissä kuluttajalta puuttuu kasvokkainen kontakti myyjään, mikä voi vähentää kuluttajan luottamusta myyjää kohtaan. Tällaisessa tilanteessa kuluttaja voi käyttää brändejä viitteenä myyjän luotettavuudesta. Tämän tutkielman tarkoituksena on tutkia brändiluottamuksen vaikutusta kuluttajan tyytyväisyyteen, luottamukseen ja uskollisuuteen Internet-sivuja kohtaan. Tutkielman kysely (n=875) toteutettiin Vauva-lehden Internet-sivuilla. Tutkielman tulokset paljastavat, että brändiluottamuksella on merkittävä myönteinen vaikutus kuluttajan tyytyväisyyteen, luottamukseen ja uskollisuuteen Internet-sivuja kohtaan. Internet-sivujen aikaisempikäyttö sekä rekisteröityminen sivuille vaikuttavat myös luottamukseen Internet-sivuja kohtaan. Lisäksi brändiluottamuksen vaikutus brändiuskollisuuden osoittautui erittäin merkittäväksi.

The effect of oxygen delignification on fiber properties in kraft pulp production - a review

Fiber damages comprise fiber deformations, characterized as fiber curl, kink, dislocations and strength losses as well as some yet unidentified factors. This recently discovered phenomenon is especially evident in mill scale kraftpulps. Laboratory produced pulps tend to have less damages and superior strength properties compared to those produced in pulp mills. Generally fiber damages pose a problem in the production of reinforcement pulp because they tend to decrease the ability of fibers to transmit load. Previous studies on fiber damage have shown that most of the fiber damages occur during brown stock processing starting from cooking and discharging. This literature review gives an overall picture on fiber damages occurring during softwood kraft pulp production with an emphasis on the oxygen delignification stage. In addition the oxygen delignification stage itself is described in more detailed extent in order to understand the mechanisms behind the delignification and fiber damaging effect. The literature available on this subject is unfortunately quite contradictory and implicates a lotof different terms. Only a few studies have been published which help to understand the nature of fiber damages. For that reason the knowledge presented in this work is not only based on previous studies but also on research scientist and mill staff interviews.

The Effect of Operational Disturbances on Reliability and Operation Time Distribution of NCmachine Tools in FMS

This thesis concentrates on studying the operational disturbance behavior of machine tools integrated into FMS. Operational disturbances are short term failures of machine tools which are especially disruptive to unattended or unmanned operation of FMS. The main objective was to examine the effect of operational disturbances on reliability and operation time distribution for machine tools. The theoretical part of the thesis covers the fimdamentals of FMS relating to the subject of this study. The concept of FMS, its benefits and operator's role in FMS operation are reviewed. The importance of reliability is presented. The terms describing the operation time of machine tools are formed by adopting standards and references. The concept of failure and indicators describing reliability and operational performance for machine tools in FMSs are presented. The empirical part of the thesis describes the research methodology which is a combination of automated (ADC) and manual data collection. By using this methodology it is possible to have a complete view of the operation time distribution for studied machine tools. Data collection was carried out in four FMSs consisting of a total of 17 machine tools. Each FMS's basic features and the signals of ADC are described. The indicators describing the reliability and operation time distribution of machine tools were calculated according to collected data. The results showed that operational disturbances have a significant influence on machine tool reliability and operational performance. On average, an operational disturbance occurs every 8,6 hours of operation time and has a down time of 0,53 hours. Operational disturbances cause a 9,4% loss in operation time which is twice the amount of losses caused by technical failures (4,3%). Operational disturbances have a decreasing influence on the utilization rate. A poor operational disturbance behavior decreases the utilization rate. It was found that the features of a part family to be machined and the method technology related to it are defining the operational disturbance behavior of the machine tool. Main causes for operational disturbances were related to material quality variations, tool maintenance, NC program errors, ATC and machine tool control. Operator's role was emphasized. It was found that failure recording activity of the operators correlates with the utilization rate. The more precisely the operators record the failure, the higher is the utilization rate. Also the FMS organizations which record failures more precisely have fewer operational disturbances.